Sie sind auf Seite 1von 13

www.sigmatrainers.

com

TRAINERS Since 23 Years

PULSE CODE MODULATION TRANSMITTER & DEMODULATION RECEIVER TRAINER

MODEL-COM203-COM204

More than 2000 Trainers

SIGMA TRAINERS AHMEDABAD (INDIA)

INTRODUCTION
This trainer has been designed with a view to provide practical and experimental knowledge of Pulse Code Modulation technique as practically implemented in Digital Communication systems on a SINGLE P.C.B. SPECIFICATIONS 1. Power supply requirement 2. Built in IC based power supply. 3. On Board Sampling Pulse signal generator. Frequency Range - Fast Mode Frequency Range - Slow Mode : 1.2 to 1.4 MHz : 0.8 Hz to 1.2 HZ : 230V AC, 50 Hz.

4. Built in variable DC power supply (0 to+ 5V) to see the effect of DC on the output waveform. 5. On Board Input Audio amplifier with Volume control for modulating external signal from Mike or Tape recorder. 6. On Board Output Audio amplifier with speaker & Volume Control. 7. LED indicators for PCM output bits. 8. Modulator Sections 9. Demodulator Sections 10. Standard Accessories : Ramp Generator, Comparator, Parallel to serial converter. : Serial to parallel converter, Latch, D/A converter and Low Pass Filter. : 1. A Training Manual. 2. Connecting Patch cords.

CHAPTER-1
THEORY OF PULSE CODE MODULATION
In continuous wave (CW) modulation, some parameter of a sinusoidal carrier wave is varied continuously in accordance with the message. In contrast with this, in pulse modulation, some parameter of a regular pulse train is varied in accordance with the message. One may distinguish two basic types of pulse modulation, namely, pulse-analogue modulation and pulse-code modulation. In the former, a periodic pulse train is used as the carrier wave, and some characteristic feature of each pulse (e.g.emplitude duration or position) is varied in a continuous manner in accordance with the pertinent sample value of the message signal. On the other hand, in pulse code modulation (PCM), a discrete-time, discrete amplitude representation is used for the signal and, as such, it has no CW counterpart. In a PCM system, the message signal is sampled and the amplitude of each sample is rounded off to the nearest one of a finite set of allowable values and the rounded values are coded. (i) PCM The essential operations on the transmitter of a PCM system are sampling, quantising and encoding, as shown in Fig. 1. The quantising and encoding operations are usually performed in the same circuit. The encoded output is the PCM signal. The PCM pulses get distorted & corrupted with noise in the transmission. The receiver regenerates these impaired signal pulses, decodes and filters to reproduce the message signal. (ii) Sampling The incoming message wave is sampled with a train of narrow rectangular pulses so as to closely approximate the instantaneous sampling process. In order to ensure perfect reconstruction of the message at the receiver, the sampling rate must be greater than twice the highest frequency component w m of the message wave. In practice, a low-pass filter is used at the front end of the sampler in order to exclude frequencies greater than w m before sampling. (iii) Quantizing A continuous signal, such as voice, has within its finite amplitude range, an infinite number of amplitude levels. However, in PCM one retains only a finite number of discrete levels by using quantisation. This introduce some error in the signal. This is called quantisation error or quantisation noise. This means that the original continuous signal may be approximated by a signal constructed of discrete amplitudes selected on a minimum error basis from an available set. Clearly if one assigns the discrete amplitude levels with sufficiently close spacing, one can make the approximated signal practically indistinguishable from the original continuous signal. Graphically, the quantising process means that a straight line representing the relation between input and output of a linear continuous system is replaced by a staircase characteristic as in Fig.2. The quantising error consists of the difference between the input and output signals of the quantizer. It is apparent that the maximum instantaneous value of this error is half of the separation between two adjacent permissible amplitude levels.

(iv) Encoding The quantised sample values are coded. Any plan for representing each of this discrete set of values as a particular arrangement of discrete event in a code is called a code One of the discrete events in a code is called a code element or symbol. In a binary code, each symbol may be either of two distinct values or kinds, such as the presence or absence of a pulse. The two symbols of a binary code results in the maximum advantage over the effects of noise in a transmission medium. It is also easy to regenerate. With an n bit (binary digit) binary code, one can represent a total of 2 n distinct numbers. There are several ways by which binary symbols 1 and 0 can be represented by electrical signals. These constitute the PCM signal.

CHAPTER-2
THEORY OF PULSE CODE DEMODULATION

(i) Decoding At the receiver, the received PCM pulses may be reshaped. The reshaped clean pulses are regrouped into code words in the receiver and decoded into a quantised PCM signal. The decoding process involves generating a pulse the amplitude of which is the linear sum of all the pulses in the code word, each pulse weighted by its place-value (2 0 , 2 1 ,2 2 ,2 3 ,....for a binary code) in the code. (ii) Filtering The final operation in the receiving is to recover the signal wave by passing the decoder output through a low-pass reconstruction filter whose cut off frequency is equal to the message bandwidth w m . Assuming that the transmission path is error free, the recovered signal includes no noise with the exception of the initial distortion introduced by the quantisation process. (iii) Quantising Noise As mentioned earlier, quantising noise is produced in the transmitter end of a PCM system by rounding off the sampled values of a continuous base band signal to the nearest permitted quantising levels. For a Quantising process, let the step size be uniform and equal to S volts. It is clear from Fig. 2 that if q e denotes the value of the error produced by the quantising process, with a random input signal, the quantising error is a random variable which is bounded by -S/2 = q e = S/2. It can also be shown that the mean squared value of the quantising noise q e is S 2 /12. When the message signal has uniform probability distribution over each setup size.

CHAPTER-3
CIRCUIT DESCRIPTION OF PULSE CODE MODULATION
The PCM Modulation and Demodulation System consist of following sections. 1. 2. 3. 4. Modulating Audio Signal Generator Sampling Pulse Generator PCM Modulator (Encoder) section Power supply.

(1) Modulating Audio Signal Generator section :IC 8038 - waveform generator - is used generate sine wave signal. 10K Pot is used to vary its frequency. The frequency range is 300 Hz to 3.4Khz. Two 100K presets are adjusted for proper peaks of sine wave signal. 1K preset is used to adjust duty cycle. The sine wave output signal available at pin 2 of IC 8038 is given to IC 356 through Amplitude pot for amplification. The amplified sinewave signal from pin 6 of IC 356 is then available at SINE O/P terminal. 22k Pot is used to vary the amplitude of Sine wave signal. The output amplitude varies from 0 to 15Vpp. (2). Sampling Pulse Generator:The function of this stage to generate sampling pulses. The basic clock is generated by NOT gates made from NAND gates (IC 4011). The clock frequency depends on R-C network selected by Switch and it can be varied by frequency pot. On FAST position the clock frequency available is 1.1 MHz to 1.4 MHz while selecting SLOW position 1 to 2 Hz clock is available. This sampling clock (1.28MHz) is then given to counter IC (4040) in modulator section. (3) Study of PCM Modulator (Encoder) section The 1.28 MHz sampling clock from sampling pulse generator is applied to binary counter IC - 4040. Assuming 3 bit/4 bit - bit select switch in the 4 bit position, then the output signals of 4040 counter viz. Q2, Q3, Q4, Q5 (at pins 2,3,5 and 6) are current weighted by resistors 10K, 22K, 39K & 82K and are summed in resistor 1K5 to produce Ramp waveform of 16 steps. (This ramp waveform can be observed at RAMP o/p socket.) The ramp is symmetrical about 0 volt. The modulating analog signal is connected at input connector from Audi sine wave generator section. This modulating signal is buffered by buffer IC 741 & applied to one input of comparator IC529 at pin 3 through 15K resistor. The ramp waveform is connected to other input of comparator 529 at pin 4. The comparator output is +6 V so long as the input voltage exceeds the ramp voltage, but when this situation is reversed the output changes to 0V. These two levels are converted to those acceptable by the remainder of the circuit, which operates with thresholds of + 2.4 V, by Zener (2.7V Zener). The output of comparator is strobed by AND gate (IC 4081 pin 8,9,10), which derives its other, input from AND gate (IC 4081 pin 13,12,11). This occurs once for every step of the ramp. So long as the comparator output is high the strobe cause o/p at pin 10 (4081) to go high so that the data presented at inputs D0, D1, D2, D3 of latch (IC 4042 pin 4, 7, 13, 14) is latched to the outputs Q0', Q1', Q2', Q3' (IC 4042 pin 2,10, 11, 1). However, when the ramp voltage exceeds the input and the comparator goes low, the latch ceases to be clocked and the previous digital number is stored. When the counter is full, all inputs to NAND gate (IC 4068) are high & the output goes low (pin 13 of 4068), consequently the Enable input of Shift register (IC 4021 pin 9) goes high and the parallel data present on inputs P0-P7 (IC 4021 pin 5,10,13,14) are loaded. This data is PCM 4 bit data and are given to NOT gates (IC 4049) for display on LED as well as these data are clocked at pin 3 in serial form, the clock signal being taken from the Q1 output of Counter (IC 4040 pin 7). This serial data forms the PCM output and is available at PCM o/p socket. A synchronization output is provided to assist in viewing the PCM output with CRO Operation of bit select switch selects 3-bit operation by providing a permanently low fourth bit. Here logic 1 is +6 Volt and logic 0 is -6 Volt. The PCM data streams consist of two guard bits (Low), four data bits (High or low as per input signal), two guard bits (Low) and eight-bit long Sync pulse (High).

(4) Power supply section:The regulated power supply is used for different supply voltages. Following output D.C. Voltages are required to operate PCM Modulation demodulation system. +15V, 250mA -15V, 250mA + 6V, 500mA - 6V, 500mA, Three terminal regulators are used for different output voltages i.e. IC IC IC IC 7815 7915 7806 7906 for for for for +15V, -15V, +6V, -6V,

These ICs are supplied different dc input voltages by two Bridge rectifiers consisting of D1-D4 and D5-D8 & two 1000/25 EC and 1000/10 EC. The capacitors at each input & each output are for filtering purpose.

CHAPTER-4
CIRCUIT DESCRIPTION OF PULSE CODE DEMODULATION
The PCM Demodulation System consist of following sections. 1. Pulse Code Demodulator (Decoder) section 2. Low pass filter 3. Power supply. (1) Study of PCM Demodulator (Decoder) section The decoder also incorporates a sampling clock made of NAND gates ( IC 4011). This clock is gated by the sync detector consisting of IC 3140 (used as comparator) and transistor Q1 (2N2907A). When the PCM input is high Q1 is turned OFF and capacitor C1- 560pf charges through resistor R1 - 33K, when the PCM input is low, Q1 conducts discharging C1-560pf. The time constant C1 & R1 is selected so that the voltage on the comparator (IC 3140) reaches the threshold set by two 33K resistors at pin 2 of 3140 after six consecutive high pulses. When the threshold is reached (during the sync pulse only), the comparator output goes low and inhibits the clock. At the end of the sync pulse C1 is discharged, the comparator output returns to the high state, the clock starts and the counter 4040 is reset. The clock output is divided by two by the D flip flop 4013. (Divided o/p is available at pin 1 of IC 4013.) This divided clock is regated by AND gate (IC 4081 pin 1,2,3) to form relatively narrow clock pulses with their leading edge delayed (delay time is decided by 4K7 and 33pf ) from the PCM data transition by half a pulse width. This pulse is further gated by AND gate (IC 4081 pin 4,5,6) and is used to clock the shift resister (IC 4015). The counter 4040 and inverter (IC 4011 pin 8, 9,10) allow eight clock pulses to occur before AND gate (IC 4081 pin 4,5,6) is inhibited. Thus the two sets of guard bits and four data bits are loaded into shift register (4015). The data bits Q0, Q1, Q2, Q3 (at pin 3,10,12,13 of IC 4015) are loaded into latch (IC 4040) by NAND gate (IC 4011 pin 12,13,11) on the ninth clock pulse. The output of the latch is connected to weighted resistors identical to those in the decoder, which sum a current into resistor R9-1K5. The voltage developed across R9-1K5 is amplified to restore the original level. (2). Low pass filter: This section passes only low frequencies up to 3.4 KHz and reduces all other frequencies. This filter is required to remove high frequency quantisation error noise from demodulated signal. This section is based on IC 741 and R-C circuits. (3) Power supply section: The regulated power supply is used for different supply voltages. Following output D.C. Voltages are required to operate PCM Modulation demodulation system. + 6V, 500mA - 6V, 500mA, Three terminal regulators are used for different output voltages i.e. IC 7806 for +6V, IC 7906 for -6V, These ICs are supplied different dc input voltages by two Bridge rectifiers consisting of D1-D4 & two 1000/16 uF and 100/16 uF. The capacitors at each input & each output are for filtering purpose.

BLOCK DIAGRAM OF PULSE CODE MODULATION


Modulating Audio Signal
AF

Comparator + Strobe Latch

Sampled Data

Shift Register
Parallel to Seri al Co n v ert er

PCM Signal T3

T1 -

Adder

Ramp Signal

T6

Sync Gen.

Counter

T2

SPG

BLOCK DIAGRAM PCM DEMODULATOR


Sync Detector PCM Signal Sampling Pulse Generator Sync SPG Sync Clk Counter

Sync Det.

Shift Register t Serial to Parallel Converter

Strobe Latch D/A Converter

Raw Data T4 LPF

Recovered Data T5

Low Pass Filter

EXPERIMENT PROCEDURE
EXP. (1). TO GENERATE PCM SIGNAL BY MODULATING WITH AUDIO SIGNAL GENERATOR: 1. Connect MOD I/P terminal of PCM modulator to Sine O/P terminal of Audio Oscillator. Connect CRO channel-1 at Sine O/P terminal (T1) of Audio Oscillator. Connect ground of probe to ground terminal of Audio oscillator. Adjust amplitude of sine wave to 2 Vpp and audio frequency to 1 KHz. _______Waveform (T1) 2. Connect CRO channel-2 at Samp Clock terminal (T2) of Sampling pulse generator. Connect ground of probe to ground terminal of PCM demodulator. Keep Freq. Selection switch at Fast Position. _______Waveform (T2) 3. Then connect CRO channel-2 at PCM O/P terminal of modulator. Keep Bit select switch at 4-bit position. The PCM modulated waveform will be seen. ______ Waveform (T3) EXP. (2). TO OBSERVE THE EFFECT OF DC SIGNAL INPUT ON PCM OUTPUT 4. Now connect variable DC signal at MOD I/P terminal of PCM modulator. I.e. connect link between VARD.C. and MOD I/P terminals. Keep Freq. Selection switch at Fast Position. 5. Vary the DC volts control POT in DC Source section and see counting effect on LEDS output. EXP. (3). TO Demodulate PCM SIGNAL: 6. Connect link between PCM O/P terminal and PCM I/P terminal. Connect CRO channel-2 at RAW DATA terminal of demodulator. Observe quantised recovered raw data signal. ______ Waveform (T4) 7. Change bit select switch to 3-bit position and observe steps in output. The steps will be reduced to 8 from 16. 8. Then connect CRO channel-2 at FIL O/P terminal of Low pass filtered and observe filtered recovered output signal. ______ Waveform (T5)

10

TEST POINT WAVEFORMS


T1. Modulating Sinewave signal: (at Sine O/P terminal of Audio Oscillator) : 1 KHz, 2Vpp-

+ 1V
H = 0.5 ms V = 1.0 V Trig = CRO-1

- 1V
1 ms

T2. Sampling Clock signal: - (1.28 MHz, TTL).

+6V

H = 0.2 us V = 5.0 V Trig= CRO-2

-6V
0.8us T3 Ramp Signal (25KHz): -

+1V

40 us
H = 20 us V = 1.0 V Trig= CRO-2

-1V

11

T4 PCM O/P signal

8 bit high Level Sync. +6V


10 us

40us

2 bit

2 bit

H = 10 us V = 5.0 V Trig= CRO-2

12

13

Das könnte Ihnen auch gefallen