Sie sind auf Seite 1von 7

S

P ro d u c t N u m b e r : P ro d u c t N a m e :

PT-AX100
High Definition Home Cinema Projector

As of August 2006. Specifications subject to change without notice.

< 1 >

High Definition Home Cinema Projector


Specifications
Main Unit LCD*1 panel: Panel size: Display method: Drive method: Pixels: Pixel configuration: Lamp* :
2

PT-AX100
0.7 diagonal (16:9 aspect ratio) Transparent LCD panel (x 3, R/G/B) Active matrix 921,600 (1,280 x 720) x 3, total of 2,764,800 pixels Stripe 220 W UHM lamp 2,000 lumens or more (high power mode) 85 % 6,000:1*3 (full on/full off, dynamic iris on) Manual zoom/focus lens (1:1 1:2), F 1.9 3.1, f 21.7 43.1 mm 40 200 inches (1,016 5,080 mm) diagonally, 16:9 aspect ratio 1.212.4 m (311408) (16:9 aspect ratio) Horizontal: 25%, vertical: 63% Vertical: approx. 30 Ceiling/floor, front/rear

Brightness: Centre-to-corner uniformity ratio: Contrast: Lens: Projection size: Throw distance: Optical axis shift*4: Keystone correction range: Installation: Scanning frequency: S-Video/Video:

fH 15.75 kHz, fV 60 Hz (NTSC, NTSC4.43, PAL-M, PAL60) fH 15.63 kHz, fV 50 Hz (PAL, PAL-N, SECAM)

PC (RGB): YPBPR (YCBCR):

fH 3070 kHz, fV 50 87 Hz 480i (525i): fH 15.75 kHz, fV 60 Hz 480p (525p): fH 31.5 kHz, fV 60 Hz 576i (625i): fH 15.63 kHz, fV 50 Hz 576p (625p): fH 31.25 kHz, fV 50 Hz 720/50p (750/50p): fH 45 kHz, fV 60 Hz 720/60p (750/60p): fH 37.5 kHz, fV 50 Hz 1080/24p (1125/24p): fH 27.0 kHz, fV 24 Hz 1080/50i (1125/50i): fH 28.125 kHz, fV 50 Hz 1080/50p (1125/50p): fH 56.3 kHz, fV 50 Hz 1080/60i (1125/60i): fH 33.75 kHz, fV 60 Hz 1080/60p (1125/60p): fH 67.5 kHz, fV 60 Hz

Terminals:

HDMI IN: S-VIDEO IN: VIDEO IN: PC (RGB) IN: R, G, B: HD/SYNC, VD: COMPONENT IN: Y: PB/PR (CB/CR): SERIAL IN:

19-pin HDMI connector x 1 Mini DIN 4-pin x 1, Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms RCA pin x 1, 1.0 Vp-p, 75 ohms D-sub HD 15-pin (female) x 1, 0.7 Vp-p (1.0 Vp-p for Sync on G), 75 ohms TTL, high impedance (positive/negative polarity) RCA pin (Y, PB/CB, PR/CR) x 1 1.0 p-p, 75 ohms 0.7 Vp-p, 75 ohms Mini DIN 8-pin (female) x 1, for external control (RS-232C compliant) English, French, German, Spanish, Italian, Chinese, Korean, Russian, Swedish, Danish, Norwegian, Polish, Czech, Hungarian, Portuguese, Thai

On-screen menu languages:

As of August 2006

< 2 >

High Definition Home Cinema Projector


Power supply: Power consumption: Dimensions (W x H x D): Weight: Operating temperature: Operating humidity: 100240 V AC, 50/60 Hz

PT-AX100
290 W (0.08 W in standby mode with fan stopped) 395 x 112 x 300 mm (15-17/32 x 4-13/32 x 11-25/32) *5 4.9 kg (10.8 lbs) 0 40C (32104F) 20%80% (no condensation)

Remote Control Power supply: Operating range: 3 V DC (AA battery x 2) Approx. 7 m (23) (when operated directly in front of signal receptor) Dimensions (W x H x D): Weight: 48 x 138 x 28 mm (1-7/8 x 7-27/32 x 1-3/32) 125 g (4.4 oz.)

Optional Accessories Replacement lamp: ET-LAX100 Ceiling mount bracket: ET-PKX100 Serial adapter: ET-ADSER (DIN 8-pin/D-sub 9-pin)

Weights and dimensions shown are approximate. Specifications subject to change without notice.

*1:

The projector uses a type of liquid crystal panel that typically consists of millions of pixels. This panel is built with very high-precision technology designed to provide one of the finest possible images. Occasionally, a few pixels may remain turned on (bright) or turned off (dark). Please note that this is an intrinsic characteristic of the manufacturing technology that affects all products using LCD technology.

*2:

The projector uses a high-voltage mercury lamp that contains high internal pressure. This lamp may break, emitting a large sound, or fail to illuminate, due to impact or extended use. The length of time that it takes for the lamp to break or fail to illuminate varies greatly depending on individual lamp characteristics and usage conditions.

*3: *4: *5:

In AI mode Shift range is limited during simultaneous horizontal and vertical shifting. Lens and legs not included.

As of August 2006

< 3 >

High Definition Home Cinema Projector

PT-AX100

Dimensions

271.1 (10-21/32)

300 (11-25/32)

102.5 (4-1/32) 395 (15-17/32)

69 (11/16)

unit : mm (inch) NOTE: This illustration is not drawn to scale.

Terminals
1 2 3 4 5

1 2 3
6

Serial input HDMI input PC (RGB) input Component (Y/P B /P R ) Input S-Video input Video input

4 5 6

RGB IN connector pin assignment


6 11 15

no. 1 2 3 4

signal R G B GND GND

no. 6 7 8 9 10

signal GND GND GND NC GND

no. 11 12 13 14 15

10

D-sub HD 15-pin, female

As of August 2006

112 (4-13/32)

121 (4-3/4)

signal GND NC HD/SYNC VD NC

< 4 >

High Definition Home Cinema Projector


Standard setting-up positions

PT-AX100
*2 49 (1-15/16)
43 (1-11/16)

H L 179 Projected image L H (7-1/16)

*1

366 446 (14-13/32 17-9/16) Adjustable in 20 mm (25/32) steps

unit : mm (inch)
Lower edge of projected image

W L

65 (2-9/16)

70 (2-3/4)

NOTE:
Projected image

62 (2-7/16)

Illustrations show the projector installed using optional ceiling bracket ET-PKX100. This illustration is not drawn to scale. Values shown are approximate.

Projection distance (screen aspect ratio 16:9))


Projection size (16:9) Diagonal length 1.01 m / 1.52 m / 2.03 m / 40 60 80 Projection distance (L) Min (Wide) 1.2 m / 311 1.8 m / 510 2.4 m / 710 3.1 m / 102 3.7 m / 121 4.6 m / 151 6.2 m / 204 Max (Telephoto) 2.4 m / 710 3.7 m / 121 4.9 m / 16 Height from the edge of screen to center of lens (E) -0.07 m 0.57 m / 2.8 110 -0.10 m 0.85 m / 3.9 411 -0.13 m 1.13 m / 5.1 38 -0.16 m 1.40 m / 6.3 47 -0.19 m 1.68 m / 7.5 56 -0.24 m 2.11 m / 9.4 611 -0.32 m 2.81 m / 12.6 93 Width from the right edge of screen to center of lens (W) 0.22 m 0.67 m / 0.33 m 1.00 m / 0.44 m 1.33 m / 9 11 15 22 33 44 55 67 82

2.54 m / 100 3.05 m / 120 3.81 m / 150 5.08 m / 200

6.2 m / 204 7.4 m / 243 9.3 m / 306 12.4 m / 408

0.55 m 1.66 m / 110 0.67 m 2.00 m / 0.83 m 2.49 m / 1.11 m 3.32 m / 22 29

38 1011

Projection distance (screen aspect ratio 4:3))


Projection size (4:3) Diagonal length 1.01 m / 1.52 m / 2.03 m / 40 60 80 Projection distance (L) Min (Wide) 1.5 m / 411 2.3 m / 77 3.0 m / 910 3.8 m / 126 5.7 m / 188 Max (Telephoto) 3.0 m / 910 4.5 m / 149 6.0 m / 198 7.6 m / 2411 11.4 m / 375 Height from the edge of screen to center of lens (E) -0.01 m 0.62 m / 0.4 -0.01 m 0.93 m / 0.4 2 3 Width from the right edge of screen to center of lens (W) 0.19 m 0.63 m / 0.28 m 0.94 m / 0.37 m 1.26 m / 0.46 m 1.57 m / 0.69 m 2.35 m / 7 11 13 16 23 2 31 42 52 79

-0.02 m 1.24 m / 0.8 41 -0.02 m 1.55 m / 0.8 51 -0.03 m 2.32 m / 1.2 77

2.54 m / 100 3.81 m / 150

NOTE: The values of L shown above vary due to characteristics of the zoom lens. Images may slightly distort due to characteristics of the zoom lens when the zoom lens is set to the minimum throw distance.

Calculation of the projection distance For a screen size different from the above, use the equation below to calculate the projection distance.
16 : 9 4 : 3 minimum maximum minimum maximum L L L L (m) (m) (m) (m) = = = = (diagonal (diagonal (diagonal (diagonal screen screen screen screen size size size size in in in in inches) inches) inches) inches) x x x x 0.0311 0.0621 0.0381 0.0761 0.056 0.056 0.046 0.056

NOTE: The accuracy of calculated value by the formula shown above is 5%.

As of August 2006

< 5 >

High Definition Home Cinema Projector


Computer Data Compatibility

PT-AX100

This projector accepts up to 70 kHz horizontal scanning frequency and 108 MHz dot clock. See the list of compatible signals on the next page for details.
NOTE: The display resolution of this projector is 1280 x 720 pixels. If the display resolution indicated in the above data does not match this resolution, the input signal will be converted to 1280 x 720 pixels (16:9 aspect ratio) or 960 x 720 pixels (4:3 aspect ratio).

Notes on Projector Placement and Operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions. 1. 2. 3. Never place objects on top of the projector while it is operating. Make sure there is an unobstructed space of 200 mm or more around the projectors air intake openings. If the projector is placed in a box or enclosure, ensure the temperature of the air surrounding the projector is between 0C/32F and 35C/95F. Also make sure the projectors intake and exhaust openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is not sucked into the intake openings.
200 mm (7-7/8) or more 200 mm (7-7/8) or more 200 mm (7-7/8) or more

Direction of Air Intake and Exhaust

Intake Exhaust

Operating the Projector Continuously 1. 2. If the projector is to be operated continuously 10 hours or more, lamp replacement cycle duration becomes shorter. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods.

As of August 2006

< 6 >

High Definition Home Cinema Projector


List of Compatible Signals
Scanning frequency H (kHz) 15.7 15.6 15.7 15.6 31.5 31.3 33.8 28.1 27.0 56.3 67.5 45.0 45.0 31.5 37.5 43.3 72.1 30.1 35.2 37.9 48.1 46.9 53.7 37.2 45.1 48.4 56.5 60.0 68.7 72.1 45.3 64.0 67.5 64.0 48.8 V (kHz) 59.9 50.0 59.9 50.0 59.9 50.0 60.0 50.0 24.0 50.0 60.0 60.0 50.0 59.9 75.0 85.0 138.0 60.1 56.3 60.3 72.2 75.0 85.1 59.9 60.1 60.0 70.1 75.0 85.0 89.0 56.5 71.2 74.9 60.0 59.8 13.5 13.5 27.0 27.0 74.3 74.3 74.3 148.5 148.5 74.3 74.3 25.2 31.5 36.0 62.3 31.5 36.0 40.0 50.0 49.5 56.3 51.4 76.5 65.0 75.0 78.8 94.5 99.2 76.2 94.2 108.0 108.0 73.8

PT-AX100
Dot clock frequency (MHz) Picture quality 2

Mode

Display resolution (dots) 1 720 x 480i 720 x 576i 720 x 480i 720 x 576i 720 x 483 720 x 576 1 920 x 1 080i 1 920 x 1 080i 1 920 x 1 080 1 920 x 1 080p 1 920 x 1 080p 1 280 x 720 1 280 x 720 640 x 480 640 x 480 640 x 480 640 x 480 856 x 480 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 1 072 x 600 1 280 x 720 1 024 x 768 1 024 x 768 1 024 x 768 1 024 x 768 1 024 x 768 1 280 x 768 1 152 x 864 1 152 x 864 1 280 x 1024 1 366 x 768

Format

NTSC/NTSC 4.43/ PAL-M/PAL60 PAL/PAL-N/SECAM 525i (480i) 625i (576i) 525p (480p) 625p (576p) 1,125 (1,080)/60i 1,125 (1,080)/50i 1,125 (1,080)/24p 1,125 (1,080)/50p 1,125 (1,080)/60p 750 (720)/60p 750 (720)/50p VGA480

A A A A A A AA AA AA AA AA AA AA A A A A A A A A A A A AA A A A A A A A A A A

VIDEO/S-VIDEO VIDEO/S-VIDEO YP BPR YP BPR YP BPR /HDMI YP BPR /HDMI YP BPR /PC/HDMI YP BPR /PC/HDMI YPBPR /HDMI YPBPR /PC YPBPR /PC YP BPR /HDMI YP BPR /HDMI PC/HDMI PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC

WIDE480 SVGA

WIDE600 WIDE720 XGA

WIDE768 MXGA SXGA WIDE768-2

1. The i appearing after the resolution indicates an interlaced signal. 2. The following symbols are used to indicate picture quality. AA Maximum picture quality can be obtained. A Signals are converted by the image processing circuit before pi ture is projected. c

As of August 2006

< 7 >

Das könnte Ihnen auch gefallen