Beruflich Dokumente
Kultur Dokumente
The best way to imagine what an edge milling machine does, is to think of it as a "router for natural stones". The main difference lies in the composite of the bits. In order to work on stone you need diamond bits.
FLEX edge milling tools are highly productive specialized tools. They are equipped with powerful motors (11 AMP and 15 AMP motors), full wave electronics, infinitely adjustable speeds and feature pressure and temperature overload protection. Their portability gives the professional maximum flexibility.
1.
Use the LW1509 WET grinder to "break the edges" of the slab. This means the professional uses a WET grinder with a diamond cup wheel and grinds away the edges to approximately the requested design. Bringing the edge into the approximate shape with a WET grinder, will reduce the wear and tear of the edge milling bits.
3.
Replace the grinding bit from the edge milling machine with a milling bit. The milling bit is significantly finer and will deliver a much smoother edge. It is important to have a relatively fine edge prior to using the natural stone WET polishers (LW1503, LW603VR, LW1302AT or PLW903S). The smoother the edge, the less the wear will be on the diamond resin polishing pads.
2.
Use the grinding bit with the edge milling machine (LWW2106VR or LWW1506VR) to transform the broken edge into the desired shape. The edge will however still be relatively coarse and will require fine grinding (milling) prior to polishing.
4.
Polish the edge with a natural stone WET polisher and the appropriate diamond resin polishing pads. Always start with the 60 grit polishing pad and work through the polishing sequence until the requested luster is achieved.
10
NATURAL STONE
LWW2106VR is the "heavy duty" two handed edge milling machine from FLEX. It is designed to handle up to 1-3/4 thick granite slabs. This product is ideally suited for the edge milling of larger natural stone surfaces (counters, tables or double basin kitchen sink holes). LWW2106VR is a portable tool yet has the power of conventional stationary CNC machines.
LWW1506VR is the "smaller sibling". It is a single handed edge milling machine. The LWW1506VR is designed to handle up to 1-1/4 thick slabs. Because of its relative light weight, this product is ideally suited for the edge milling of smaller sink holes and fireplace mantle pieces.
Type of tool
Application
Type of stone
LWW2106VR
Grinding and milling of edges into requested shapes Preparation edge shaping prior to fine polishing LARGE surfaces (counters, tables or double basin kitchen sink holes) Grinding and milling of edges into requested shapes Preparation edge shaping prior to fine polishing SMALL surfaces (bathroom sink holes, single basin kitchen sink holes, fire place mantle pieces)
LWW1506VR
11
Edge Milling Machine for Marble & Granite Slabs up to 1-3/4 Thickness
LWW2106VR
Edge Milling Machine For Marble and Granite Slabs up to 1-1/4 Thickness
LWW1506VR
Two-handed electronic edge milling tool used to round edges of natural stone slabs, counter tops and tables of up to 1-3/4 in thickness. The LWW2106VR is a portable tool, yet has the power and flexibility of conventional stationary machines. 2 handed electronic edge milling machine 15 AMP motor 1,800-5,500 RPM 1/2 G spindle thread Central and external water feed FLEX electronics Integrated electrical surge protection Soft start RPM pre-set dial RPM cruise control Overload protection Temperature sensors Ground fault circuit interrupter built into power cord 22 lbs
Single-handed edge milling machine designed to handle up to 1-1/4 thick slabs. Because of its relative light weight, it is ideally suited for the edge milling of smaller sink holes and fireplace mantle pieces. Single-handed electronic edge milling machine 11 AMP motor 2,200-6,500 RPM 1/2 G spindle thread Central water feed FLEX electronics Integrated electrical surge protection Soft start RPM pre-set dial RPM cruise control Overload protection Temperature sensors Ground fault circuit interrupter built into power cord 13 lbs
Standard equipment: 1 rugged edge milling machine 1 hex wrench SW 8 x 100 x 130 1 open-ended wrench 1 splash guard 1 guide carriage WET diamond edge milling bits need to be purchased individually.
Standard equipment: 1 compact edge milling tool 1 hex wrench SW 8 x 100 x 130 1 open-ended wrench 1 guide carriage 1 Splash guard WET diamond edge milling bits need to be purchased individually.
SPECIFICATIONS Speed For slab thickness Power input Power output Weight
LWW1506VR 2,200-6,500 RPM 3/4 - 1-1/4 11 AMP 700 Watts 12-3/4 lbs
LWW2106VR
NEW
NEW
NEW
NATURAL STONE
NEW
B profile
NEW
T profile
NEW
G 1/2 thread Granite 20 mm thick Granite 30 mm thick Granite 40 mm thick Type Order No. Type Order No. Type Order No.
Part Number
Description
Machine
LWW1506VR LWW2106VR
NEW
16237
Quick connect hose adapter not pictured not pictured not pictured not pictured Splash guard for LWW1506VR 24-mm open-ended wrench 32-mm open-ended wrench Splash guard for LWW2106VR
257456
198781
251475
257226
256005