Beruflich Dokumente
Kultur Dokumente
Copyright
Copyright 2004 LiteOn Technology Corp. All Rights Reserved This manual may not, in whole or in part, be copied, photocopied, reproduced, translated, or converted to any electronic or machine readable form without prior written permission of LiteOn Technology Corp. HP HPD_R15AAC/AAU(vs15) Service Manual.
Trademarks
LiteOn is a registered trademark of LiteOn Technology Corp. All other trademarks are the property of their respective owners.
Printed in Taiwan.
2) Inverter Circuit
2. Inverter Circuit ----------------------------------------------------------------------------------------------------------------- 5
3) Interface Operation
3.1 Top --------------------------------------------------------------------------------------------------------------------------- 6 3.2 Power ------------------------------------------------------------------------------------------------------------------------ 6 3.3 VGA & DDC interface ----------------------------------------------------------------------------------------------------- 6 3.4 Scaler GM5321 ------------------------------------------------------------------------------------------------------------- 7 3.5 Key & Panel interface ----------------------------------------------------------------------------------------------------- 8 3.6 Audio ------------------------------------------------------------------------------------------------------------------------ 9 3.7 Others --------------------------------------------------------------------------------------------------------------------- 10 3.7.1 Detection of POWER switch status -------------------------------------------------------------------------------- 10 3.7.2 Display mode identification ------------------------------------------------------------------------------------------ 10 3.7.3 List of I/O Pin Assignments of the I311 ---------------------------------------------------------------------------- 12
4) Trouble Shooting
1. 2. 3. 4. 5. 6. For Power Board ------------------------------------------------------------------------------------------------------------- 13 For Inverter Board ----------------------------------------------------------------------------------------------------------- 14 No display of screen (Screen is black, color of LED is amber) -------------------------------------------------------- 15 Nothing displays on screen (Screen is black, color of LED is green) ------------------------------------------------ 16 Checking the back light unit ----------------------------------------------------------------------------------------------- 18 Abnormal screen ------------------------------------------------------------------------------------------------------------- 19 6.1 Abnormal screen for VGA source ------------------------------------------------------------------------------------- 19 7. 8. Abnormal OSM display adjust problem ---------------------------------------------------------------------------------- 20 Abnormal plug and play operation --------------------------------------------------------------------------------------- 21 8.1 Abnormal plug and play operation for VGA ------------------------------------------------------------------------- 21
Page 2
R15AAC/AAU (vs15)
9. Checking the interface circuit of sync signal ---------------------------------------------------------------------------- 22 9.1 Checking the control circuit of horizontal sync pulse for VGA -------------------------------------------------- 22 9.2 Checking the control circuit of vertical sync pulse VGA ---------------------------------------------------------- 22 10. Checking the resolution change IC movement -------------------------------------------------------------------------- 23 11. Audio no signal output ----------------------------------------------------------------------------------------------------- 24
5) Spare Parts
Recommended Spare Parts List ------------------------------------------------------------------------------------------------- 26
6) Block Diagram
Block diagram ---------------------------------------------------------------------------------------------------------------------- 27
Page 3
R15AAC/AAU (vs15)
Line Filter
Power Transformer
PWM
Driver
FB
Page 4
R15AAC/AAU (vs15)
2) Inverter Circuit
This unit operates on an output voltage of 21.5V from power source. 2.1 2.2 VDD: R105 get a +5VDC for I101 power supply. Control IC: I101 (OZ9930)
2.2.1 Enable : When pin 1 of I101 is over 0.55V, I101 works. If it is under 0.55V, I101 turns off. 2.2.2 OSC: When I101 enabled, C104/C105 (pin 2 of I101) determine the operating frequency. 2.2.3 SST: C106 (pin 1 of I101) provides soft start function. 2.2.4 Ignition: IC provides higher operating frequency internally for more striking voltage until regulation of feedback of lamp current. And provide 2 sec striking time. 2.2.5 Dimming control: The divided voltage of R106/R103/R104 control the duty pulse of burst-mode to drive and perform a wide dimming control for the CCFL. The burst-mode frequency is determined by operating freq/233. 2.2.6 Regulation: Pin 8 of I101 provide regulation of the CCFL current from feedback. The non-inverting reference is at 1.25V nominal. 2.2.7 Protection: Open-lamp protection in the ignition period is provided through pin 7 of I101. Removal of the CCFL during normal operation will trigger IC to turns on and shuts off the inverter. This is latch function. 2.2.8 Output drivers: The configuration prevents any shoot-through issue associated with bridge-type power conversion applications. Adjusting the overlap conduction between Q104, the CCFL current regulation is achieved. 2.3 2.4 2.5 Half-bridge swit ching/Transformer: Q104, C122, C123 compose half-bridge swit ching to convert DC into AC for driver the CCFL. Detection: C132, C112, C114, C126, R116, R115, C115 detect the output voltage and ensure a rated voltage by pin7 of I101 ensure not a open-lamp. Feedback: D116, D117, R111, R112, C109 sense the lamp current for negative feedback and regulation.
VCC
VDD VDD Control IC : OZ9930 Enable Output driver OSC SST Brightness Dimming Control Control Regulation Feed back Protection Ignition Halfl-bridge switching Transformer Lamp
ON / OFF
Detection
Page 5
R15AAC/AAU (vs15)
3) 3.1
Interface Operation Top (Circuit diagrams sheet 2 of 8) This page is function block. (1) Power. (2) VGA & DDC interface. (3) Scaler GM2621. (4) Key & panel interface. (5) Audio Power (Circuit diagrams sheet 3 of 7) 3.2.1 P301 connector A 5V power supply for flash ROM, EEPROM of EDID, logic. It is generated from the P301 connector. 3.2.2 I304 : 3-terminal regulator A 3.3V power supply for I307 scaler IC gm2621 LCD module, it is generated from the 5V source. 3.2.3 I305 : 3-terminal regulator A 1.8V power supply for I307 scaler IC gm2621, it is generated from the 3.3V source (I304). 3.2.4 Q302, I301 : ON/OFF control for LCD module power ON/OFF control (PANELVCC_EN) is performed for power ON/OFF and also for the power saving sequence. It is support 3.3V to LCD module power. The PANELVCC_EN signal is generated from I307 scaler IC gm2621. 3.2.5 R305: ON/OFF control for LCD module back light power ON/OFF control (BKLT_EN) is performed for black light power ON/OFF and also for the power saving sequence. The BKLT_EN signal is generation from I307 scaler IC gm2621. 3.2.6 Q301 : Adjust back light luminance for LCD module It is adjusted back light luminance control (BKLT_ADJ) is performed for the back light luminance. The BKLT_ADJ signal is generated from I307 scaler IC gm2621. VGA & DDC interface (Circuit diagrams sheet 4 of 7) This sheet have RGB analog video signals input from VGA connector. Select H/V sync signals source from VGA connector. The RGB analog video signals input through AC-coupled, analog video signal is used to clamp the black level at 0V. And H/V sync to sclaer. And support DDC plug & play function for analog video. 3.3.1 P302 connector The RGB analog video input signals from the P302 connector. 3.3.2 I306 DDC EEPROM This IC is support DDC2B of the VESA standard, also plug and play for the PC host.
3.2
3.3
Page 6
R15AAC/AAU (vs15) 3.4 Scaler gm2621 (Circuit diagrams sheet 5 of 7) The I307 gm2621 is all-in-one LCD monitor controller. The gm2621 leverages Genesis patented advanced image-processing technology as well as a proven integrated ADC/PLL. Gm2621 also integrates a micro-controller, an OSD controller, and dual LVDS. The RGB analog video signal input entered from the video input circuit is converted into the digital data of analog video signal through the incorporated A/D converter. Based on this conversion, this device performs interpolation during pixel extension. These interpolation digital data are transformed to LVDS signal. The I307 source voltage is 3.3V and 1.8V, the device clock source frequency is 14.318 MHz. And support keypad function. 3.4.1 I310 SPI Flash ROM The firmware program running from I310 external ROM, contains firmware code and data for all firmware function, and control data and parameter and OSD related setting and other service data. The device is 8bit configuration, 1024K bytes of ROM. 3.4.2 I308 Microprocessor Supervisory Circuit The function of this device is to assert a reset to I307 scaler gm2621, if either the power supply dropped down. 3.4.3 X301 14.318MHz It generated reference clock input for I311 scaler. 3.4.4 ISP and DDC2Bi function The DDC2Bi is VESA standard for the host PC system, it can through DDC2Bi bus control LCD monitor. Enter I307 pin54 DDC_SCL and pin55 DDC_SDA of the VGA port. It use ISP function when change new firmware to I310 flash ROM. It used DDC2B port IIC bus through I307 gm2621 to I310 flash ROM. 3.4.5 The power save sequence function First disable I307 pin49 (BKLT_EN) from H to L of LCD module back light power, delay some time, then disable I307 pin127 (PANELVCC_EN) from H to L of LCD module power, then I307 enter to power down mode.
Page 7
R15AAC/AAU (vs15) 3.5 Key & Panel interface (Circuit diagrams sheet 6of 7) 3.5.1 P306 connector It is LVDS bus, it is from I307 scaler to LCD panel module. The output voltage is 3.3V. 3.5.2 P307 connector The P307 has support keypad function. Control is give effect to for the push switch to be used when the user changes the parameters, in order to modify the respective setting values. Whether the switch has been pressed is identified with the switch input level that inputs a DC voltage into I107 pin113 (LBADC_IN3) and pin114 (LBAD1_IN2). Each switch input voltage based on Table 1. Each parameter is stored in the I310 EEPROM, the contents of which are updated as required. The P307 have LED Blue and Amber light, the LED Blue signal from I307 pin 51, and the LED Amber signal from I307 pin 56.
sw itc h inp ut
U p key o r So urce 2
2 .3V
LB A D C _ P in 11 3 IN 3 P in 11 3
K EY _DO W N
sw itc h inp ut
Selectio n s w itc h input
D o w n ke y or So urce 1
1 .9V
K E Y _ SE L E C T
1 .57 V
Page 8
R15AAC/AAU (vs15) 3.6 Audio (Circuit diagrams sheet 7 of 7) 3.6.1 P307 connector The P307 is audio signal input from the keypad function board. 3.6.2 P308 connector The P308 have two audio function signals. One is audio volume control from the keypad function board. Other is audio output to speaker or ear phone-jack. 3.6.3 I312 TDA74965A The I312 is 5x5W stereo audio amplifier, it is an integrated class-B dual output amplifier. 3.6.4 Q308, I313: ON/OFF control for Audio power ON/OFF control (AUDIO_PW) is performed for power ON/OFF and also for the audio power down sequence. It is support 12V to audio power. The AUDIO_PW signal is generated from I307 scaler IC gm2621. 3.6.5 R385, Q309: MUTE control for Audio MUTE control (MUTE) is performed for audio return to mute and also for the audio power down sequence. The MUTE signal is generated from I307 scaler IC gm2621.
Page 9
R15AAC/AAU (vs15) 3.7 Others 3.7.1 Detection of POWER switch status The I307 gm2621 identifies the ON status of the two power supplies. The identification is made when the power supply is turn off. For example, if the power supply is turn off with the POWER switch, the POWER switch must be turn on when active the power supply again. If the power supply is turned off by pulling out the power cord, then this power supply can be turned on by connecting the power cord, without pressing the POWER switch. 3.7.2 Display mode identification 3.7.2.1Display mode identification The display mode of input signal is identified based on Table 2. When the mode has been identified through the measurement of horizontal and vertical frequencies, the total number of lines is determined with a formula of Horizontal frequency / Vertical frequency = Total number of number of lines. Final identification can be made by examining the coincidence of the obtained figure with the number of lines for the mode identified from the frequency. The Distinction Hsync and Vsync of each mode is shown in Table 3. When the detected frequency if the sync signal has changed, the total number of lines should be counted even through it is range identified frequency in the same mode. 3.7.2.2Out of range This out of range mode is assumed when the frequency out of the horizontal / vertical signal is as specified below. Vertical frequency : 56 ~ 76 Hz. Horizontal frequency : 30 ~ 63KHz. 3.7.2.3Power save mode The power save mode is assumed when the horizontal / vertical signals are as specified below. If there is no horizontal sync signal input. If there is no vertical sync signal input. If the horizontal sync signal is outside the measuring range of I307 gm2621. If the vertical sync signal is outside the measuring range of I307 gm2621.
Page 10
R15AAC/AAU (vs15) Table 2 video mode Mode 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Resolution 640x480 (59.94Hz) 640x480 (72Hz) 640x480 (75Hz) 720x400 (70Hz) 800x600 (60Hz) 800x600 (72Hz) 800x600 (75Hz) 832x624 (74.55Hz) 1024x768 (60Hz) 1024x768 (75Hz) 1152x870 (75Hz) 1152x900 (76Hz) 1280x960 (60Hz) 1280x1024 (60Hz) 1280x1024 (75Hz) H-Freq (KHz) 31.469 37.861 37.5 31.469 37.879 48.077 46.875 49.722 48.363 60.023 68.68 71.71 60 63.981 79.976 Band Width (MHz) 25.175 31.5 31.5 28.322 40 50 49.5 57.28 65 78.75 100 105.6 108 108 135 Polarity H + + + + +/+/+ + V + + + + + +/+/+ +
Page 11
R15AAC/AAU (vs15) 3.7.3 List of I/O Pin Assignments of the I311 Pin No. 51 56 50 57 58 115 127 49 Port GPIO0 GPIO1 GPO4 GPO2 GPO3 PPWR PBIAS Signal Name LED_B LED_A BKLT_ADJ MUTE AUDIO_PW PANELVCC_EN BKLT_EN Initial Setting L L L L H L L Function LED green enable LED amber enable Backlight brightness control Mute Audio ON/OFF Audio power VGA cable connected Panel power enable Back light power enable
LBADC_IN1 VGA_DETn
Page 12
NG
OK
OK
NG
Turn switch on
Check power cord (P801), signal cable (P302), P802, P101, P102, P103, P104 is connected right or not
OK
NG
Connect it right
OK
NG
OK
NG
OK
NG
OK
NG
Check Q803, R813, R814, D806, R811, R815 and repair them
OK
NG
Check D809, D810, D811, C818. C829, C813, C824, C822, T802 have same short circuit or the output +5V, +12V, +21.5V is over load
OK
NG
Repair them
Check feedback circuit around I802, I803 and the other components and repair them
Page 13
R15AAC/AAU (vs15)
2.
Check C102 pin is around 5V. On/Off pin of P802 is over 2V. Brightness pin is between 0V and 3.5V/
OK
NG
OK
NG
OK
NG
OK
NG
OK
NG
Check pin 1 of I101, there is soft start edge up to 4V and pin 4, 5. there is some pulse outputs
OK
NG
Repair I101
OK
NG
OK
NG
Repair them
Page 14
R15AAC/AAU (vs15)
3.
When a sugnal isn't being inputed, it is indicated with "VIDEO INPUT". it is indicated with "OUT OIF RANGE" at the time of the frequency that it can't be distinguished.
No Yes
Check if the sync signal from computer is output and if the video cable is connected normally. (VGA or DVI)
NG OK
Page 15
R15AAC/AAU (vs15) 4. Nothing displays on screen (Screen is black, color of LED is green)
Is backlight lit?
NG OK
Check the video cable for failure. Check the host for output signal with all black only.
NG OK
1)Change pattern of video signal output on the host. 2)Rsconnect the video cable. 3)Change the video cable.
Check OSM menu is display on screen when you push the "PROCEED" key.
NG OK
Check if the LCD module signal cable is connected between the Interface Board and LCD module.
Failure Point NG OK Proceed "Abnormal sreen" dection" The LVDS cable is disconnected.
Next Page
Page 16
R15AAC/AAU (vs15)
Continue
Check the 5V power are supplied on P306 pin 1, 2, 3 (to the LCD panel)
NG
Check if the TTL level on I301 pin1 that TTL level is low (0~0.8V). OK Check the PANELVCC_EN signal of the rectangle input Q303 pin2 at TTL high level.
NG OK
Failure Point 1) Prined wire broke between Q302 pin 3, R117, R308, C313 and I301 pin1. 2) Q312 is failure.
Failure Point Check the P306 all LVDS signals. 1) Printed wire broke between Q302 pin 2 and I307 pin127. 2) I307 is failure.
Failure Point NG OK 1) Printed wire broke between P306 and I307 LVDS signals. 2) I307 is failure.
Failure Point 1) The LVDS cable broke between P306 and LCD module. 2) LCD module is failure.
Page 17
Check the BKLT_EN signal of the rectangle input P302 pin 6 at TTL high level.
Failure Point NG OK 1) printed wire broke between P302 pin6, R306 and I311pin 68. 2) R324, R325, C330 are open or short. 3) I311 is failure.
Check the BKLT_ADJ signal of the input P302 pin5 from I311 pin98 is a PWM signal.
Failure Point NG OK 1) printed wire broke between P302 pin5, Q303, Q304 and I311 pin98. 2) Q303 or Q304 is failure. 2) I311 is failure.
Page 18
R15AAC/AAU (vs15) 6. Abnormal screen 6.1 Abnormal screen for VGA source
Check the R, G, B video signal from computer input on P302 of video connector.
NG OK
Failure Point 1) No R, G, B video signals output from host computer, check computer. 2) VGA video signal cable disconnection.
Check the R, G, B input video signals on I307 pin93, 96, 99 respectively that their level is 0.5 to 0.7Vp-p.
NG OK
Failure Point In the case of the Red signal. (Green and Blue signal is the same path, too.) 1) Printed wire broke between P303 pin 1 and I307 pin99. 2) Video cable is failure. 3) FB308, FB309, R313 are open. 4) R318 is short. 5) C325 is short or open. 6) C329 is short.
NG OK
Failure Point 1) Printed wire broke between I311 and P305. 2) LVDS cable failure.
Page 19
Check the input DC voltage level whether was changed when pressed function keys on the P307 pin 8, 9. (normal is low level, when push buttom, generated a DC level plus) (Refer table 1)
NG OK
Failure Point 1) Function key wire disconnection. 2) Function key wire is failure. 3) Function key board is failure. 4) R390, R391 are open 5) R371, R370 are open or short 6) R365, R366, R367, R368, R369 are open or short or not correct assistance.
Page 20
R15AAC/AAU (vs15) 8. Abnormal plug and play operation 8.1 Abnormal plug and play operation for VGA
NG OK
NG OK
NG OK
Failure Point 1) Printed wire broke between I306 pin8, D306, D309 and P302 pin9. 2) D306 is failure. 3) D310 is short.
Check the voltage on P302 pin12, 15 that is serial data / clock signal.
NG OK
NG OK
Failure Point 1) Printed wire broke between I309 pin5, 6 and P302 pin12, 15. 2) R332, R333 is open. 3) C338, C339 is short.
Page 21
R15AAC/AAU (vs15) 9. Checking the interface circuit of sync signal 9.1 Checking the control circuit of horizontal sync pluse for VGA
NG OK
Check the horizontal sync signal on I307 pin189 TTL level. Failure Point NG OK 1) Printed wire broke between P302 pin13 and I307 pin189. 2) R323 is open. 3) R326, C335 are short.
9.2 Checking the control circuit of vertical sync pluse for VGA
NG OK
Check the horizontal sync signal on I307 pin90 TTL level. Failure Point NG OK 1) Printed wire broke between P302 pin13 and I307 pin90. 2) FB315, R324 are open. 3) R325, C334 are short.
Page 22
Check +3.3V supply on I307 pin2, 25, 47, 53, 91, 92, 74, 82, 101, 110, 116, 128.
NG OK
Check +1.8V supply on I307 pin118, 87, 55, 17, 86, 78, 70, 104, 106.
NG OK
Check X301 14.318MHz clock input to I307 pin108 and 109 at TTL level.
Failure Point NG OK 1) Printed wire broke between X301 and I307 pin108, 109. 2) C347, C348 short or open. 3) X301 failure.
Check I307 pin111 RESETn signal is high level at normal operation. Failure Point 1) Check I308 pin2 is low level wait 240ms to high level, when AC power is plug in. 2) I308 failure. 3) Printed wire broke between I307 pin111 and I308. 2) C351 short. 3) I307 failure.
NG OK
Failure Point NG OK 1) Printed wire broke between I307 pin59, 60, 61, 62 and I310. 2) I310 failure.
Page 23
R15AAC/AAU (vs15)
Failure Point OK NG 1) No audio signal from the audio source. 2) Audio cable is failure.
Check audio signal input of the I312 TDA7496SA pin5 . Failure Point 1) FB322, FB323, R372, R373 are open. C385 C387, C391, C392 are short. 2) Audio output wire is disconnected from the interface board P309 and key function board P601. 3) Printed wire broke between P601 and J600 of the function board.
OK
NG
Next Page
OK NG
OK
OK
Page 24
R15AAC/AAU (vs15)
Continue
Failure Point NG OK 1) Printed wire broke between I307 pin57 and Q309and I312 pin10. 2) R383, R384, R385, R338, C393 are open or short. 3) Q312 is filure. 4) I307 is failure.
Failure Point NG OK 1) Printed wire broke between I312 pin12, 14 and P309 pin1, 3. 2) C386, C388 open or short. 3) I312 is failure.
Failure Point NG OK 1) Audio output wire is disconnected from the interface board P309 to key function board P601. 2) Printed wire broke between P601 and J600 for the key function board. 3) C610, C609 are short. 4) J600 phone-jack is failure. 5) Audio speaker unit is disconnected from P602.
Page 25
R15AAC/AAU (vs15)
5) Spare Parts
Recommended Parts List Note: 1. The components identified by mark are critical for X-ray safety. Replace these with only the same parts specified. 2. There is only OTP IC at the model beginning (FPR stage or before). When it put in mass production and there must be Mask coming out. If you have spart parts need, please check BOM to get the last release part number and related information.
No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Location Part Number I301 I306 I304 I305 I307 I312 X301 I310 I801 I101 T801 T802 6442097000 6442044700 6138004300 6131054010 6449006400 6448018208 6448018218 6442023326 6442040708
Description IC 24LC02B SOP-8 MICROCHIP IC M24C02 SOP-8 ST FET P-Channel AO3401 SOT-23 AOS IC Linear AIC1084-33CM TO-263 IC Linear AIC1117A-18CY SOT-223 IC Scaler gm2621 PQFP-128P Genesis IC TDA7496SA Crystal 14.318MHz AT-49 TOPICS IC flash ROM SST39SF020A-70 PLCC-32 SST IC-LINEAR-FAN7601-8P-DIP-FAIRCH ILD IC-LINEAR-DZ9930D-8P0DIP-O2 XFMER-TPW-1137-EEL19B LINE FILTER 15Mh XFRNER-TPW-1136-ER28 IC-CMOS-AOP607
Q104,105 6444023100
Page 26
6)
CCFL
LCD Module
VS15 -> Panel 1. AUO LM150XN07 Panel 2. CPT CLAA150XP01
D
Block Diagram
CCFL
1. 2. 1. 2.
P306
Brightness, Inv_On/Off
+12V
PMC 25LVF010
P600
DC-DC
P309
I312
+12V
I306
DDC_CLK, DDC_DATA
DSUB
Audio output Right/Left
P302
To ear phone
Audio In
of
Size:
Custom
DWG.NO:
R15AAC/AAU (vs15)
Page 27
Allen Lai
R15AAX
SCHEMATIC REV 02 PTB-1579 Nov 22 2004
ROAD MAP
DESCRIPTION
C
SHEET NO. 1 2 3 4 5 6 7
C
TITLE SHEET TOP POWER VGA & DDC INTERFACE SCALER GM5621 KEY & PANEL INTERFACE AUDIO
REVISION HISTORY
REV. 0A 01
B
DESCRIPTION BASED ON PTB-1551 Rev.0C SCHEMATICE FOR LITEON Revrsion change Add C405,C406,C407 for ESD protecter
BY
02
7/30'04
DRAWN: CHECK:
Sheet:
Title:
of
Size:
Custom
Date: Date:
APPRO:
5 4 3 2
APPRO:
8815790000-02 6832157900-02
1
3.VGA & DDC INTERFACE RIN GNDR GIN GNDG BIN GNDB HS_IN VS_IN R G B IN GNDR IN GNDG IN GNDB HS_IN VS_IN
4.SCALER GM5621_6 R2P_CH3P_LV_E R2N_CH3N_LV_E R1P_E R1N_E R0P_E R0N_E G2P_CH0P_LV_E G2N_CH0N_LV_E G1P_CH1P_LV_E G1N_CH1N_LV_E G0P_CH2P_LV_E G0N_CH2N_LV_E B2P_E B2N_E B1P_E B1N_E B0P_E B0N_E CLKP_LV_E CLKN_LV_E R2P_CH3P_LV_O R2N_CH3N_LV_O R1P_O R1N_O R0P_O R0N_O G2P_CH0P_LV_O G2N_CH0N_LV_O G1P_CH1P_LV_O G1N_CH1N_LV_O G0P_CH2P_LV_O G0N_CH2N_LV_O B2P_O B2N_O B1P_O B1N_O B0P_O B0N_O CLKP_LV_O CLKN_LV_O T_ESP T_LP T_POL T_OSP T_ROWCLK T_RSP T_ROE LED_G LED_A LBADC_IN2 LBADC_IN3 R2P_CH3P_LV_E R2N_CH3N_LV_E R1P_E R1N_E R0P_E R0N_E G2P_CH0P_LV_E G2N_CH0N_LV_E G1P_CH1P_LV_E G1N_CH1N_LV_E G0P_CH2P_LV_E G0N_CH2N_LV_E B2P_E B2N_E B1P_E B1N_E B0P_E B0N_E CLKP_LV_E CLKN_LV_E R2P_CH3P_LV_O R2N_CH3N_LV_O R1P_O R1N_O R0P_O R0N_O G2P_CH0P_LV_O G2N_CH0N_LV_O G1P_CH1P_LV_O G1N_CH1N_LV_O G0P_CH2P_LV_O G0N_CH2N_LV_O B2P_O B2N_O B1P_O B1N_O B0P_O B0N_O CLKP_LV_O CLKN_LV_O T_ESP T_LP T_POL T_OSP T_ROWCLK T_RSP T_ROE LED_G LED_A LBADC_IN2 LBADC_IN3 R2P_CH3P_LV_E R2N_CH3N_LV_E R1P_E R1N_E R0P_E R0N_E G2P_CH0P_LV_E G2N_CH0N_LV_E G1P_CH1P_LV_E G1N_CH1N_LV_E G0P_CH2P_LV_E G0N_CH2N_LV_E B2P_E B2N_E B1P_E B1N_E B0P_E B0N_E CLKP_LV_E CLKN_LV_E R2P_CH3P_LV_O R2N_CH3N_LV_O R1P_O R1N_O R0P_O R0N_O G2P_CH0P_LV_O G2N_CH0N_LV_O G1P_CH1P_LV_O G1N_CH1N_LV_O G0P_CH2P_LV_O G0N_CH2N_LV_O B2P_O B2N_O B1P_O B1N_O B0P_O B0N_O CLKP_LV_O CLKN_LV_O T_ESP T_LP _POL T_OSP T_ROWCLK T_RSP T_ROE LED_G LED_A LBADC_IN2 LBADC_IN3
5.KEY & PANEL INTERFACE R2P_CH3P_LV_E R2N_CH3N_LV_E R1P_E R1N_E R0P_E R0N_E G2P_CH0P_LV_E G2N_CH0N_LV_E G1P_CH1P_LV_E G1N_CH1N_LV_E G0P_CH2P_LV_E G0N_CH2N_LV_E B2P_E B2N_E B1P_E B1N_E B0P_E B0N_E CLKP_LV_E CLKN_LV_E R2P_CH3P_LV_O R2N_CH3N_LV_O R1P_O R1N_O R0P_O R0N_O G2P_CH0P_LV_O G2N_CH0N_LV_O G1P_CH1P_LV_0 G1N_CH1N_LV_O G0P_CH2P_LV_O G0N_CH2N_LV_O B2P_O B2N_O B1P_O B1N_O B0P_O B0N_O CLKP_LV_O CLKN_LV_O T_ESP T_LP T_POL T_OSP T_ROWCLK T_RSP T_ROE LED_G LED_A LBADC_IN2 LBADC_IN3
2.POWER
6.AUDIO
2.POWER
4.SCALER GM5621_6
6.AUDIO
DRAWN: CHECK:
Sheet:
Title:
of
Size:
Custom
R15AAX TOP
APPRO:
5 4 3 2
APPRO:
8815790000-02 6832157900-02
1
VCC5V P301
D
VCC5V
1 2 3 4 5 6 7 8 JWT-A2001WV2-08
FB301 FB302
BACKLIGHT_ADJ BACKLIGHT_EN FB303 PBY160808T-121Y-S VCC15V C303 0.1uF C306 0.1uF C307 47uF/25V C304 0.01uF C305 22uF/16V
C301 0.1uF(NC)
C302 1uF
R303 16.9K
Q301 MMBT3904 1
BKLT_ADJ
BKLT_ADJ 5
R305 100
BKLT_EN
BKLT_EN 5
C308 0.1uF
R306 10K
VCC5V
FB304 PBY160808T-121Y-S(0) FB305 PBY160808T-121Y-S(NC) R307 47K R308 C313 1uF C309 100uF/16V C310 1 0.1uF I301 AO3401 2 3 G
VCC3V3
VLCD
R389 100(NC)
5 PANELVCC_EN
PANELVCC_EN
R309 4K7
3 2 1
TO-263
VCC5V 3 1 I304 VIN ADJ VOUT TAB 2 4
VCC3V3
VCC3V3
TO-252
3 I305 VIN ADJ VOUT TAB 2 4 1
VCC1V8
AIC1084-33CM
C322 22uF/16V
C323 10uF/16V
AIC1117A-18CY
C324 22uF/16V
DRAWN: CHECK:
Sheet:
Title:
of
Size:
Custom
R15AAX POWER
8815790000-02 6832157900-02
1
P302 17 1 9 2 10 3 11 4 12 5 13 6 14 7 15 8 16 VGA_RED VGA_5V VGA_GREEN VGA_CONn VGA_BLUE 3 3 VGA_SDA VGA_HSYNC VGA_VSYNC VGA_SCL D301 MMBD7000 VCC5V 1 2 D302 MMBD7000 VCC5V 1 2 D303 MMBD7000 VCC5V 1 2 3 FB308 FB310 FB312 0 0 0 RED GREEN BLUE FB309 FB311 FB313 SBK160808T-600Y-S SBK160808T-600Y-S SBK160808T-600Y-S RED_IN R313 R314 100 120 C325 C326 10nF 10nF RIN GNDR
RIN 5 GNDR 5
R316 75/1%
R317 75/1%
R318 75/1%
GREEN_IN
R315 R319
100 120
C327 C328
10nF 10nF
GIN GNDG
GIN 5 GNDG 5
C330 0.1uF
C331 0.1uF
BLUE_IN
R320 R321
100 120
C332 C333
10nF 10nF
BIN GNDB
BIN 5 GNDB 5
CONNECTOR DB15
VGA_CONn
VGA_DETn
VGA_DETn 5
FB314 FB315
BK2125HS431 BK2125HS431
HS_IN VS_IN
HS_IN 5 VS_IN 5
D305 MMSZ5232B
D306 MMSZ5232B
3V3_DVDD
R327 VGA_5V
B
VCC5V DDC_5V R328 DDC5V_A R329 4K7 R330 4K7 D310 MMSZ5232B C337 0.1uF 8 7 6 5 I306 VCC WP SCL SDA 24C02 A0 A1 A2 GND 10K D307 1N4148(NC)
0 3V3_SPI
B
C336 0.1uF
D308 1N4148
D309 1N4148
3V3_SPI 5
2 1 2 3 4 Q304 MMBT3904 1
R331 4K7
DDC_WPn
DDC_WPn 5
R332 R333
DDC_SCL_VGA DDC_SDA_VGA
DDC_SCL_VGA DDC_SDA_VGA
DDC_SCL_VGA 5 DDC_SDA_VGA 5
DRAWN: CHECK:
Sheet:
Title:
of
Size:
Custom
Date: Date:
APPRO:
5 4 3 2
APPRO:
8815790000-02 6832157900-02
1
VCC3V3
FB316
3V3_RPLL
3V3_RPLL 3V3_AVDD
3V3_LV
3V3_DVDD
1V8_CVDD
1V8_AVDD
101 92
128
116
118 87 55 17
104 AVDD_ADC_18
I307 VCC3V3 3V3_AVDD 3V3_RPLL C342 10uF/16V C343 0.1uF C344 0.1uF C345 0.1uF C346 0.1uF C347 15pF X301 14.318MHZ C348 VCC3V3 3V3_LV VCC5V C349 1uF C350 0.1uF I308 VCC VCC3V3 3V3_DVDD FB319 RST GND MIC809MU C353 10uF/16V
C
AVDD_ADC_33 AVDD_ADC_33
RVDD_33 RVDD_33
AVDD_DVI_33 AVDD_DVI_33
AVDD_BIAS_33
LBADC_VDD_33
AVDD_RPLL_33
VDD_RPLL_18
106
82 74
2 25 47
53 91
86 78 70
FB317
PBY160808T-121Y-S
2.2pF
XTAL TCLK
108 109
XTAL TCLK
FB318
PBY160808T-121Y-S
4 4 4 4 4 4
99 100 96 97 93 94 89 90 111
C351 10nF 4 3V3_SPI C352 0.1uF DDC_SCL_VGA DDC_SDA_VGA 3V3_SPI DDC_SCL_VGA DDC_SDA_VGA 63 64 65 66 67 RESERVED DDC_SCL_VGA DDC_SDA_VGA DDC_SCL_DVI DDC_SDA_DVI
PBY160808T-121Y-S C354 0.1uF C355 0.1uF C356 0.1uF C357 0.1uF C358 0.1uF C359 0.1uF
E_R0N/RESERVED E_R0P/RESERVED E_R1N/RESERVED E_R1P/RESERVED E_R2N/CH3N_LV_E E_R2P/CH3P_LV_E ECLKN/CLKN_LV_E ECLKP/CLKP_LV_E E_G0N/CH2N_LV_E E_G0P/CH2P_LV_E E_G1N/CH1N_LV_E E_G1P/CH1P_LV_E E_G2N/CH0N_LV_E E_G2P/CH0P_LV_E E_B0N/RESERVED E_B0P/RESERVED E_B1N/RESERVED E_B1P/RESERVED E_B2N/RESERVED E_B2P/RESERVED
3 4 5 6 7 8 9 10 11 12 13 14 15 16 19 20 21 22 23 24
R0N_E R0P_E R1N_E R1P_E R2N_CH3N_LV_E R2P_CH3P_LV_E CLKN_LV_E CLKP_LV_E G0N_CH2N_LV_E G0P_CH2P_LV_E G1N_CH1N_LV_E G1P_CH1P_LV_E G2N_CH0N_LV_E G2P_CH0P_LV_E B0N_E B0P_E B1N_E B1P_E B2N_E B2P_E
R0N_E 6 R0P_E 6 R1N_E 6 R1P_E 6 R2N_CH3N_LV_E R2P_CH3P_LV_E CLKN_LV_E 6 CLKP_LV_E 6 G0N_CH2N_LV_E G0P_CH2P_LV_E G1N_CH1N_LV_E G1P_CH1P_LV_E G2N_CH0N_LV_E G2P_CH0P_LV_E B0N_E B0P_E B1N_E B1P_E B2N_E B2P_E 6 6 6 6 6 6
6 6 6 6 6 6 6 6
4 DDC_SCL_VGA 4 DDC_SDA_VGA
VCC1V8
FB320
1V8_CVDD 72 73 75 76 80 81 83 84 3V3_DVDD 3V3_AVDD R334 250/1%(NC) REXT 69 RX2+ RX2RX1+ RX1RX0+ RX0RXC+ RXCREXT O_R0N/RESERVED O_R0P/RESERVED O_R1N/RESERVED O_R1P/RESERVED O_R2N/CH3N_LV_O O_R2P/CH3P_LV_O OCLKN/CLKN_LV_O OCLKP/CLKP_LV_O O_G0NCH2N_LV_O O_G0P/CH2P_LV_O O_G1N/CH1N_LV_O O_G1P/CH1P_LV_O O_G2N/CH0N_LV_O O_G2P/CH0P_LV_O O_B0N/RESERVED O_B0P/RESERVED O_B1N/RESERVED O_B1P/RESERVED O_B2N/RESERVED O_B2P/RESERVED
PBY160808T-121Y-S C360 10uF/16V C361 0.1uF C362 0.1uF C363 0.1uF C364 0.1uF
VCC1V8
FB321
1V8_AVDD R335 C365 10uF/16V C366 0.1uF C367 0.1uF C368 0.1uF C369 0.1uF C370 0.1uF 7 3 7 7 VOLUME BKLT_ADJ AUDIO_PW MUTEn 6 LED_A 6 LED_G 10K(NC) VOLUME BKLT_ADJ AUDIO_PW MUTEn LED_A LED_G R336 2k2 VOLUME BKLT_ADJ UART_DO_SDA UART_DI_SCL LED_A LED_G 119 50 58 57 56 51 PWM1/GPO_5 PWM0/GPO_4 GPO_3 GPO_2 GPO_1 GPO_0
27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46
R0N_O R0P_O R1N_O R1P_O R2N_CH3N_LV_O R2P_CH3P_LV_O CLKN_LV_O CLKP_LV_O G0N_CH2N_LV_O G0P_CH2P_LV_O G1N_CH1N_LV_O G1P_CH1P_LV_O G2N_CH0N_LV_O G2P_CH0P_LV_O B0N_O B0P_O B1N_O B1P_O B2N_O B2P_O
R0N_O 6 R0P_O 6 R1N_O 6 R1P_O 6 R2N_CH3N_LV_O R2P_CH3P_LV_O CLKN_LV_O 6 CLKP_LV_O 6 G0N_CH2N_LV_O G0P_CH2P_LV_O G1N_CH1N_LV_O G1P_CH1P_LV_O G2N_CH0N_LV_O G2P_CH0P_LV_O B0N_O B0P_O B1N_O B1P_O B2N_O B2P_O 6 6 6 6 6 6
6 6 6 6 6 6 6 6
PBY160808T-121Y-S
R337 R338
0 0
127 49 105
PANELVCC_EN BKLT_EN
PANELVCC_EN 3 BKLT_EN 3
VCC5V
C371
B
0.1uF DDC_WPn
5 4 3
I309 VCC Y GND A B 1 2 LED_A LED_G 4 3V3_SPI R339 10K SPI_CSn SPI_DO 1 2 3 4 I310 CE# SO WP# GND VCC HOLD# SCK SI 8 7 6 5 3V3_SPI C372 0.1uF SPI_HOLDn SPI_CLK SPI_DI R340 10K
59 60 61 62
107 AVSS_RPLL
NC74AHCT1G08DCK/NC7ST08P5
gm5621 PQFP-128
95 98 102 103
SPI_WP
Q310 MMBT3906
SST25VF010
PM25LV010
6 LBADC_IN3 6 LBADC_IN2
LBADC_IN3 LBADC_IN2 R343 C374 0.1uF R344 820K C375 0.1uF 3V3_DVDD
18 52 54 88 117
68 71 77 79 85
26 48
4 DDC_WPn
AVSS_BIAS
SPI_CSn SPI_CLK SPI_DI SPI_DO AVSS_ADC AVSS_ADC AVSS_ADC AVSS_ADC AVSS_DVI AVSS_DVI AVSS_DVI AVSS_DVI AVSS_DVI
VSS_OUT VSS_OUT
PIN51 PIN119
High is disable, Low is enable, for the J-TAG port. High is UART on GPO, Low is UART on DDC. 4 VGA_DETn
820K
R345 10K
VGA_DETn
R346
R347 100K
A
C376 0.1uF
A
7/30'04
DRAWN: CHECK:
Sheet:
Title:
of
Size:
Allen Lai
Allen Lai
8815790000-02 6832157900-02
APPRO:
5 4 3 2
APPRO:
P305 32 31 5 B2P_O 5 B2N_O 5 B1P_O 5 B1N_O 5 B0P_O 5 B0N_O 5 G2P_CH0P_LV_O 5 G2N_CH0N_LV_O 5 G1P_CH1P_LV_0 5 G1N_CH1N_LV_O 5 G0P_CH2P_LV_O 5 G0N_CH2N_LV_O 5 CLKP_LV_O 5 CLKN_LV_O 5 R2P_CH3P_LV_O 5 R2N_CH3N_LV_O 5 R1P_O 5 R1N_O 5 R0P_O 5 R0N_O B2P_O B2N_O B1P_O B1N_O B0P_O B0N_O G2P_CH0P_LV_O G2N_CH0N_LV_O G1P_CH1P_LV_O G1N_CH1N_LV_O G0P_CH2P_LV_O G0N_CH2N_LV_O CLKP_LV_O CLKN_LV_O R2P_CH3P_LV_O R2N_CH3N_LV_O R1P_O R1N_O R0P_O R0N_O 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 AF730X-AXG1T(P-TWO)
B2P_E B2N_E B1P_E B1N_E B0P_E B0N_E G2P_CH0P_LV_E G2N_CH0N_LV_E G1P_CH1P_LV_E G1N_CH1N_LV_E G0P_CH2P_LV_E G0N_CH2N_LV_E CLKP_LV_E CLKN_LV_E R2P_CH3P_LV_E R2N_CH3N_LV_E R1P_E R1N_E R0P_E R0N_E T_ESP T_LP T_POL T_ROWCLK T_RSP T_ROE TP1 POINT
5 B0P_E 5 B0N_E 5 G2P_CH0P_LV_E 5 G2N_CH0N_LV_E 5 G1P_CH1P_LV_E 5 G1N_CH1N_LV_E 5 G0P_CH2P_LV_E 5 G0N_CH2N_LV_E 5 CLKP_LV_E 5 CLKN_LV_E 5 R2P_CH3P_LV_E 5 R2N_CH3N_LV_E 5 R1P_E 5 R1N_E 5 R0P_E 5 R0N_E 10K(NC) 0(NC) 10K(NC) VLCD 5 T_ESP 5 T_LP 5 T_POL 5 T_ROWCLK 5 T_RSP 5 T_ROE R351 R352 0(NC) 0(NC)
T_OSP
R349 R350
50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 AF750X-AXG1T(P-TWO)
5 R2N_CH3N_LV_E 5 R2P_CH3P_LV_E 5 CLKN_LV_E 5 CLKP_LV_E 5 G0N_CH2N_LV_E 5 G0P_CH2P_LV_E 5 G1N_CH1N_LV_E 5 G1P_CH1P_LV_E 5 G2N_CH0N_LV_E 5 G2P_CH0P_LV_E
R2N_CH3N_LV_E R2P_CH3P_LV_E CLKN_LV_E CLKP_LV_E G0N_CH2N_LV_E G0P_CH2P_LV_E G1N_CH1N_LV_E G1P_CH1P_LV_E G2N_CH0N_LV_E G2P_CH0P_LV_E
5 R2N_CH3N_LV_O 5 R2P_CH3P_LV_O 5 CLKN_LV_O 5 CLKP_LV_O 5 G0N_CH2N_LV_O 5 G0P_CH2P_LV_O 5 G1N_CH1N_LV_O 5 G1P_CH1P_LV_0 5 G2N_CH0N_LV_O 5 G2P_CH0P_LV_O
R2N_CH3N_LV_O R2P_CH3P_LV_O CLKN_LV_O CLKP_LV_O G0N_CH2N_LV_O G0P_CH2P_LV_O G1N_CH1N_LV_O G1P_CH1P_LV_O G2N_CH0N_LV_O G2P_CH0P_LV_O
Note: Pin19 is
no pin header
C
If it is 15" panel used 2x10 pin connector. If it is 17" panel used 2x16 pin connector.
PIN# 1 2 3 4,5 7
C380 C381 C382 C403 C404 KEY_POWERn KEY_MENUn KEY_DOWNn KEY_UPn KEY_SELECTn
VCC5V
R393
10K
2 3
Q311 MMBT3906
8,9 16
R392
B
10K
5 LED_G
VCC3V3 1
5 LED_A
LED_A
R362 2K2
2 1
R360 10K(NC)
R361 10K(NC) LED_BLUE R363 R364 470 200 B_LED A_LED 5 LBADC_IN2 5 LBADC_IN3
R390 220
5 LBADC_IN2 5 LBADC_IN3
LBADC_IN2 LBADC_IN3
C406 0.1uF
0.1uF(NC)
R370 4K7
C405 0.1uF
C383 KEY_POWERn
A
C384 0.1uF
A
KEY_MENUn
KEY_DOWNn
KEY_UPn
KEY_SELECTn
0.1uF
LBADC_IN2 LBADC_IN3
1.05V
Sheet:
Title:
of
Size:
Custom
Allen Lai
Date: Date:
Allen Lai
APPRO:
5 4 3 2
APPRO:
8815790000-02 6832157900-02
1
P308
1 2 3
I312 FB322 FB323 PBY160808T-121Y-S PBY160808T-121Y-S D313 MMSZ5232B(NC) D315 MMSZ5232B(NC) FB324 PBY160808T-121Y-S C394 S-GND R378 22k R377 R386 150K 20k C398 0.1uF S-GND L301 470uF/25V C395 0.1uF AMP_15V C396 470uF/25V C397 0.1uF R372 R373 D314 MMSZ5232B(NC) D316 MMSZ5232B(NC) S-GND S-GND AMP_VOLUME C402 0.1uF(NC) 1K 1K AUDIO_IN_L AUDIO_IN_R R374 47K C385 C387 R375 47K 0.22uF 0.22uF C391 47pF C392 47pF AMP_MUTE C393 1uF 9 3 STBY VOL NC VAO_L VAO_R AMP_IN_L AMP_IN_R 5 1 10 INL INR MUTE 6 4 2 OUTL OUTR 12 14 C386 C388 470uF/25V 470uF/25V OUT_L OUT_R 1 2 3
P309
PH-JACK-3P
D
JWT-A2001WV2-03
13 8 11 15
5 VOLUME
VOLUME
VCC15V
45uH DRWW 10 X 10
AMP_15V
C401
C400 0.1uF
100uF/25V
5 AUDIO_PW
AUDIO_PW
R382 4K7
D G S
R383
B
10K
5 MUTEn
MUTEn
MUTEn
R385 4K7
3 2 1 Q309 MMBT3904
HIGH HIGH ON
DRAWN: CHECK:
Sheet:
Title:
of
Size:
Custom
Allen Lai
Date: Date:
R15AAX AUDIO
Allen Lai
APPRO:
8815790000-02 6832157900-02
1
C801 0.33uF/250V-X 1
FG
C809
C804 2200P/250V-Y
D
2 GND
C802 3300P/250V-Y
1 D804
2 UF4005G
1 4 5
1000P/1KVX7R
C832
GND
KBP205G
C838 0.1uF/250V-X
T801 3 ET-20
R801 1M MGF
C803 2200P/250V-Y 4
T802 ER-28F 9 10
D809 2
21.5V + C818 470uF/35V 2 GND + C829 1000uF/25V GND 2 D811 24B R828 1K 2 R817 1K GND
D808 SF34G 2 1
BRI 1 ON-OFF 2
F802 +5V JUMP WIRE GND 3 4 5 6
1 2 3 4 5 6
D
GND
56UH 2
1000P/100VX7R 7
1 + C824 1000uF/10V-KF 2 2 3
GND 12V
1 + GND
C833 0.1UF
R841 1 5.1K 2
I801
8 4 3 5 1
GND-1
R830 5.6K 2
FAN7601
C810 100P/1KVX7R 3
GND-1 R823 270 I802 1 2 R826 1K R825 1K C827 0.01uF/PEM R827 26.1k MF 1% I805 AP431
C813
1000uF/25V
R842 4.7K 1
3 1 GND
R835 1M
C811 220P
GND-1
C
GND-1
VR801 10K
C
GND
3 D101 1N4148 1 2 8 7 6 1 5 2 R106 649K 2 + C103 2.2uF/50V R104 475K 1 R103 200K R105 22 2 3 GND 3 2 R132 2K GND 2 1 1 Q103 1 A733 3 4 Q102 C945 1 2 S2 G2 S1 G1 AOP605 + C124 220uF/35V GND GND GND R131 R133 10 10 GND 1 C123 2 Q104 D2 D2 D1 D1 1 8 7 6 5 1 2 + C122 470uF/25V
1 C132 22P/3KV C112 22P/3KV R116 3M 1/4W D114 1N4148 1 2 C115 5100P PEM GND GND 1 2 D115 1N4148 2 C114 10P/3KV 2
P101 2P
R102 100K 3 R118 100K 3 2 Q106 C945 1 1 1 2 Q107 C945 C106 0.047uF 2 R101 100K C105 27P C104 330P 3 4
C126 10P/3KV
P102 2P
2
B
GND
D103 1N4148 1 2
GND
1N4148 2
D116
GND
2 R119 1M
D111
1N4148
GND
2 GND
A
Sheet:
Title:
of
Size:
LITE-ON TECHNOLOGY CORP. 16 F, 392, Rueykuang. Road, Taipei, Taiwan Tel: 886-2-87982888 Fax: 886-2-87982829 Printed in Taiwan