Beruflich Dokumente
Kultur Dokumente
Engineering tolerance is the permissible limit or limits of variation in 1. a physical dimension, 2. a measured value or physical property of a material, manufactured object, system, or service, 3. other measured values (such as temperature, humidity, etc.). 4. in engineering and safety, a physical distance or space (tolerance), as in a truck (lorry), train or boat under a bridge as well as a train in a tunnel (see structure gauge and loading gauge). 5. in mechanical engineering the space between a bolt and a nut or a hole, etc.. Dimensions, properties, or conditions may vary within certain practical limits without significantly affecting functioning of equipment or a process. Tolerances are specified to allow reasonable leeway for imperfections and inherent variability without compromising performance. A variation beyond the tolerance (for example, a temperature that's too hot or too cold) is said to be non-compliant, rejected, or exceeding the tolerance (regardless of if this breach was of the lower or the upper bound). If the tolerance is set too restrictive, resulting in most objects run by it being rejected, it is said to be intolerant.
The choice of tolerances is also affected by the intended statistical sampling plan and its characteristics such as the Acceptable Quality Level. This relates to the question of whether tolerances must be extremely rigid (high confidence in 100% conformance) or whether some small percentage of being out-of-tolerance may sometimes be acceptable.
Summary of basic size, fundamental deviation and IT grades compared to minimum and maximum sizes of the shaft and hole. Dimensional tolerance is related to, but different from fit in mechanical engineering, which is a designed-in clearance or interference between two parts. Tolerances can be applied to any dimension. The commonly used terms are:
Basic size: the nominal diameter of the shaft (or bolt) and the hole. This is, in general, the same for both components.
Lower deviation: the difference between the basic size and the minimum possible component size. Upper deviation: the difference between the basic size and the maximum possible component size. Fundamental deviation: the minimum difference in size between a component and the basic size. This is identical to the upper deviation for shafts and the lower deviation for holes. If the fundamental deviation is greater than zero, the bolt will always be smaller than the basic size and the hole will always be wider. Fundamental deviation is a form of allowance, rather than tolerance. International Tolerance grade: this is a standardised measure of the maximum difference in size between the component and the basic size (see below).
For example, if a shaft with a nominal diameter of 10 mm is to have a sliding fit within a hole, the shaft might be specified with a tolerance range from 9.964 to 10 mm (i.e. a zero fundamental deviation, but a lower deviation of 0.036 mm) and the hole might be specified with a tolerance range from 10.04 mm to 10.076 mm (0.04 mm fundamental deviation and 0.076 mm upper deviation). This would provide a clearance fit of somewhere between 0.04 mm (largest shaft paired with the smallest hole, called the "maximum material condition") and 0.112 mm (smallest shaft paired with the largest hole). In this case the size of the tolerance range for both the shaft and hole is chosen to be the same (0.036 mm), meaning that both components have the same International Tolerance grade but this need not be the case in general. When no other tolerances are provided, the machining industry uses the following standard tolerances:[3][4] 1 decimal place (.x): 0.2 2 decimal places (.0x): 0.01 3 decimal places (.00x): 0.005 4 decimal places (.000x): 0.0005 International Tolerance grades Main article: IT Grade When designing mechanical components, a system of standardized tolerances called International Tolerance grades are often used. The standard (size) tolerances are divided into two categories: hole and shaft. They are labelled with a letter (capitals for holes and lowercase for shafts) and a number. For example: H7 (hole tapped hole or nut) and h7 (shaft or bolt). H7/h6 is a very common standard tolerance which gives a rather tight fit, but not so tight that you can't put the shaft in the hole, or turn the nut on the bolt, by hand. The tolerances work in such a way that for a hole H7 means that the hole should be made slightly larger than the base dimension (in this case for an ISO fit 10+0.0150, meaning that it may be up to 0.015 mm larger than the base dimension, and 0 mm smaller). The actual amount bigger/smaller depends on the base dimension. For a shaft of the same size h6 would mean 10+00.009, which is the opposite of H7.
This method of standard tolerances is also known as Limits and Fits and can be found in ISO 286-1:2010 (Link to ISO catalog). The table below summarises the International Tolerance (IT) grades and the general applications of these grades:
Measuring Tools
Material
IT Grade 01 0
9 10 11
12
13
14
15
16
Fits
An analysis of fit by Statistical interference is also extremely useful: It indicates the frequency (or probability) of parts properly fitting together.