Beruflich Dokumente
Kultur Dokumente
Page : 1 / 8 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable.
Name / Nom Written by / Rdig par Validated by / Valid par Approved by / Approuv par M.NAU R.DOREY
Signature/ Signature
Page : 2 / 8 confidential This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable.
Contents / Sommaire
1 2 Introduction .............................................................................. 4 GPRS specific AT commands list ................................................ 4
2.1 Commands available in the Class C software ..........................................4 2.1.1 Standardised commands .........................................................................4 2.1.2 Proprietary commands ............................................................................6 2.2 3 4 Commands available in the Class B software ..........................................6 Restrictions............................................................................... 6 AT command sequence for GPRS Mobile Originating session ....... 8
Page : 3 / 8 confidential This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable.
1 Introduction
The aim of this document is to list the AT commands that will be available for GPRS operation1.
2.1.1 Standardised commands AT+CGDCONT This command is used to define the PDP (Packet Data Protocol) contexts.
The parameters for this command are: PDP context identifier, PDP type (IP, PPP,), Access Point Name, PDP address, PDP data compression switch, PDP header compression switch. AT+CGQREQ This command is used to define the Quality of service profile (requested).
The parameters for this command are: PDP context identifier, precedence class, delay class, reliability class, peak throughput class, mean throughput class. AT+CGQMIN This command is used to define the minimum acceptable Quality of service profile.
The parameters for this command are: PDP context identifier, precedence class, delay class, reliability class, peak throughput class, mean throughput class. AT+CGATT This command is used to perform a GPRS attach or detach.
The parameter for this command is: GPRS attachment state AT+CGACT This command is used to activate or deactivate a specified PDP context.
The parameters for this command are: PDP context activation state, PDP context identifier.
This document is for preliminary information only. Wavecom may at any time and without notice make changes to this list. Page : 4 / 8 confidential This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable.
AT commands for GPRS 07/00 AT+CGDATA This command is used to enter data state (switch to on line mode)
The parameters for this command are: Layer 2 protocol to be used between TE and MT (null, PPP,), PDP context identifier. AT+CGPADDR This command is used to Show PDP address.
The input parameter for this command is: PDP context identifier. AT+CGAUTO This command is used to enable or disable automatic response to a network request for PDP context activation.
The input parameter for this command is: automatic response mode. AT+CGANS This command is used to respond to a network request for PDP context activation.
The parameters for this command are: Acceptance status, Layer 2 protocol to be used between TE and MT (null, PPP,), PDP context identifier. AT+CGCLASS This command is used to set the GPRS mobile station class.
The input parameter for this command is: class (C, CG, CC). AT+CGEREP This command is used to get the GPRS event reporting
The parameters for this command are: unsollicited result (buffer/discard options), unsollicited result code buffer mode. AT+CGREG This command is used to get the GPRS network registration status
code
mode
The input parameter for this command (enable/disable unsollicited status indication).
is:
registration
status
mode
In addition to the here-above specific commands, the following standard commands will be extended:
ATD for dialling ATH for hanging up ATA for answering ATS0 for automatic answer mode
Page : 5 / 8 confidential This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable.
AT commands for GPRS 07/00 2.1.2 Proprietary commands Some Wavecom specific commands might also be available such as an AT command to use the built-in TCP/IP stack (Wavecom IP PAD) including: Selection of UDP/TCP mode Selection of the distant port Selection of the IP destination address
The input parameter for this command is: service (GPRS / circuit switched).
3 Restrictions
The following commands will not be supported in GPRS mode : General commands
+CKPD
Keypad control
+VTD, +VTS ATDL %Dn +CICB +CSNS +VGR, +VGT +CMUT +SPEAKER +ECHO +SIDET +VIP
DTMF signals Redial last telephone number Automatic dialing with Incoming Call Bearer Single Numbering Scheme Gain control Microphone Mute Control Speaker & Microphone selection Echo Cancellation SideTone modification Initialize Voice Parameters
+CREG
Network registration
Page : 6 / 8 confidential This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable.
+CCFC +CLCK +CPWD +CCWA +CLIR +CLIP +COLP +CAOC +CACM +CAMM +CPUC +CHLD +CLCC +CSSN +CUSD +CCUG
Call forwarding Call barring Modify SS password Call waiting Calling line identification restriction Calling line identification presentation Connected line identification presentation Advice of charge Accumulated call meter Accumulated call meter maximum Price per unit and currency table Call related supplementary services List current calls Supplementary service notifications Unstructured supplementary service data Closed user group
All CS data and fax commands All Sim Tool Kit commands Specific commands
+WSCAN
Wavecom Scan
Page : 7 / 8 confidential This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable.
// data transfer to be operated AT+CGDATA // to switch to on-line mode (emission/reception) +++ // to switch back to command mode // then, for ex. n minutes in idle mode // then, new data transfer to be operated AT+CGDATA // to switch to on-line mode (emission/reception) +++ // to switch back to command mode // then for ex. after x hours, PDP deactivation notification from the network +CGEV : NW DETACH The AT+CGDATA or the ATD commands can directly be used if a PDP context is already defined. These commands will automatically:
perform the GPRS attach activate the PDP context switch to on-line mode
// then, to end the session AT+CGACT // to deactivate the context AT+CGATT // to perform the GPRS detach (deregistration from the network)
Page : 8 / 8 confidential This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la proprit exlcusive de WAVECOM. Il ne peut tre communiqu ou divulgu des tiers sans son autorisation pralable.