Beruflich Dokumente
Kultur Dokumente
ON
TRANSFORMER
ACKNOWLEDGEMENT
I feel proud to present my Investigatory project in Chemistry on the topic TRANSFORMER which aims at using Bleaching powder as a disinfectant and purifier to make water fit for drinking.
This project wouldn t have been feasible without the proper and rigorous guidance of my Chemistry teacher Mrs J C GUPTA who guided me throughout this project in every possible way. An investigatory project involves various difficult lab experiments which have to be carried out by the student to obtain the observations and conclude the report on a meaningful note. These experiments are very critical and in the case of failure, may result in disastrous consequences.
Rigorous hard work has been put in this project to ensure that it proves to be the best. I hope that this project will prove to be a breeding ground for the next generation of students and will guide them in every possible way.
Signature
CERTIFICATE OF AUTHENTICITY
This is to certify that CHETAN LOHIA of class XII has successfully completed the research project on the topic TRANSFORMER under the guidance of Mrs. J C GUPTA (Subject Teacher). This project is absolutely genuine and does not indulge in plagiarism of any kind. The references taken in making this project have been declared at the end of this report.
TRANSFORMER
Principle:A Transformer based on the Principle of mutual induction according to this principle, the amount of magnetic flux linked with a coil changing, an e.m.f is induced in the neighbouring coil.
CONSTRUCTION:A transformer consists of a rectangular shaft iron core made of laminated sheets, well insulated from one another. Two coils p1 & p2 and s1 & s2 are wound on the same core, but are well insulated with each other. Note that the both the coils are insulated from the core, the source of alternating e.m.f is connected to p1p2, the primary coil and a load resistance R is connected to s1 s2, the secondary coil through an open switch S. thus there can be no current through the sec. coil so long as the switch is open. For an ideal transformer, we assume that the resistance of the primary & secondary winding is negligible. Further, the energy loses due to magnetic the iron core is also negligible.
INTRODUCTION OF TRANSFORMER
A transformer is an electrical device which is used for changing the A.C. voltages. A transformer is most widely used device in both low and high current circuit. As such transformers are built in an amazing strength of sizes. In electronic, measurement and control circuits, transformer size may be so small that it weight only a few tens of grams where as in high voltage power circuits, it may weight hundred of tones. In a transformer, the electrical energy transfer from one circuit to another circuit takes place without the use of moving parts. A transformer which increases the voltages is called a step-up transformer. A transformer which decreases the A.C. voltages is called a step-down transformer. Transformer is, therefore, an essential piece of apparatus both for high and low current circuits.
Ep = -Np d
/dt
-----------------(1)
And
Es = -Ns d
/dt
----------------- (2)
Since the above relations are true at every instant, so by dividing 2 by 1, we get
Es / Ep = - Ns / Np
----------------(3)
As Ep is the instantaneous value of back e.m.f induced in the primary coil p1, so the instantaneous current in primary coil is due to the difference (E Ep ) in the instantaneous values of the applied and back e.m.f. further if Rp is the resistance o, p1p2 coil, then the instantaneous current Ip in the primary coil is given by
Ip
= E Ep / Rp
E Ep = Ip Rp
E Ep = 0 or Ep = E
In a step up transformer
If
Ip =
And
Is
Ep Ip and
Es Is
Or
Ep Ip =
Es Is
Or
Es / Ep
Ip / Is
= K
In a step up transformer
i.e. current in sec. is weaker when secondary voltage is higher. Hence, whatever we gain in voltage, we lose in current in the same ratio. Similarly it can be shown, that in a step down transformer, whatever we lose in voltage, we gain in current in the same ratio. Thus a step up transformer in reality steps down the current & a step down transformer steps up the current.
Efficiency:Efficiency of a transformer is defined as the ratio of output power to the input power. i.e. = output power / input power = Es Is / Ep Ip Thus in an ideal transformer, where there is no power losses, = 1. But in actual practice, there
are many power losses, therefore the efficiency of transformer is less than one.
ENERGY LOSSES:Following are the major sources of energy loss in a transformer: 1. Copper loss is the energy loss in the form of heat in the copper coils of a transformer. This is due to joule heating of conducting wires. 2. Iron loss is the energy loss in the form of heat in the iron core of the transformer. This is due to formation of eddy currents in iron core. It is minimized by taking laminated cores. 3. Leakage of magnetic flux occurs inspite of best insulations. Therefore, rate of change of magnetic flux linked with each turn of S1S2 is less than the rate of change of magnetic flux linked with each turn of P1P2. 4. Hysteretic loss is the loss of energy due to repeated magnetization and demagnetization of the iron core when A.C. is fed to it. 5. Magneto striation i.e. humming noise of a transformer.
USES OF TRANSFORMER
A transformer is used in almost all a.c. operations y In voltage regulator for T.V., refrigerator, computer, air conditioner etc. In the induction furnaces. y y y A step down transformer is used for welding purposes. A step down transformer is used for obtaining large current. A step up transformer is used for the production of X-Rays and NEON advertisement. y y y Transformers are used in voltage regulators and stabilized power supplies. Transformers are used in the transmissions of a.c. over long distances. Small transformers are used in Radio sets, telephones, loud speakers and electric bells etc.