Beruflich Dokumente
Kultur Dokumente
The information in this document is subject to change without notice. c SAMHOP Microelectronics Corp. All Rights Reserved. 1007 7F,No.100,Min-Chyuan Road, Hsintien, Taipei Hsien, Taiwan, R.O.C. TEL: 886-2-2218-3978/2820 FAX: 886-2-2218-3320 Email : info@samhop.com.tw
GENERAL DESCRIPTION
The SM7513 is a stereo audio power amplifier that drives 3 W/channel of continuous RMS power into a 3- load. Advanced up/down volume control minimizes external components and allows BTL (speaker) volume control and SE (earphone) volume control. Wireless headphone benefit from the integrated feature set that minimizes external components without sacrificing functionality. To simplify design, the speaker volume level is adjusted by applying a up/down gain control to the up/down terminals.
FEATURES
* Advanced DC Volume Control With 2-dB Steps From -40 dB to 20 dB * Depop circuitry * Low quiescent current * 1uA shutdown current * 3W into 3 from 5.5V supply * Thermal protection * Compact configuration and minimum external components
APPLICATIONS
* Mini Speaker * Wireless headphone * Car multimedia system
1 2 3 4 5 6 7 8
Thermal Pad
16 15 14 13 12 11 10 9
SM7513 16PIN
Page 1
PIN ASSIGNMENTS
1 2 3 4 5 6 7 8
Thermal Pad
16 15 14 13 12 11 10 9
SM7513 16PIN
PIN DESCRIPTIONS
No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Pin Name ROUTN RPVDD RLINEIN VDD LLINEIN LPVDD LOUTN LPGND LOUTP SHUTDOWN BYPASS DOWN UP SE/BTL ROUTP RPGND
I/O O I I O O I I I I I O -
Function Right channel negative audio output Supply voltage terminal for power stage Right channel line input Supply voltage terminal Left channel line input Supply voltage terminal for power stage Left channel negative audio output Power ground Left chanel positive audio output
Places the amplifier in shutdown mode if a TTL logic low is placed on this terminal Tap to voltage divider for internal midsupply bias generator used for analog reference
Terminal for volume down control, high active Terminal for volume up control, high active
Output MUX control. When this terminal is high,SE outputs are selected. When this terminal is low, BTL outputs are selected
Page 2
Unit V V C C C
Typ.
Max. 5.5
Unit V V
V C
Page 3
lDD
lDD lDD(SD)
ARMS uA
OPERATING CHARACTERISTICS (VDD =PVDD = 5V, RL = 3, Gain = 6dB, Ta = 25oC unless otherwise noted)
Characteristic Symbol Condition THD=1%, f=1 kHz, RL=4 THD=10%, f=1 kHz, RL=4 Output Power (1) PO THD=1%, f=1 kHz, RL=8 THD=10%, f=1 kHz, RL=8 THD=10%, f=1 kHz, RL=3,VDD=5.5V Total harmonic distortion+noise High-level output voltage Low-level output voltage Bypass voltage(Nominally VDD/2)(2) Maximum output power bandwidth Supply ripple rejection ratio Initial gain THD+N VOH VOL V(BYPASS) BOM PO =1W, RL=8, f=20Hz to 20kHz RL=8, Measured between output and VDD RL=8, Measured between output and GND Measured at pin 11, No load, VDD=5.5V THD = 5% f=1 kHz, Gain = 0 dB, C(BYP) = 0.47uF f= 1kHz , RL = 8 BTL SE -2 Min. Typ. 1.9 2.4 1.3 1.6 3 < 0.6 600 400 2.65 2.75 > 20 -63 -57 -4 -6 2.85 % mV mV V kHz dB dB W Max. Unit
(1) Output power is measured at the output terminals of the IC. (2) At 4V < VDD < 5.5V the DC bypass voltage is approximately VDD/2
Page 4
RLINEIN
_ +
BYP BYP
_ +
ROUT+
_ +
BYP EN
SE/BTL
ROUT-
SE/BTL
UP/DOWN
LLINEIN
_ +
BYP BYP
_ +
LOUT+
_ +
BYP EN
SE/BTL
LOUT-
Page 5
APPLICATION INFORMATION
The figure is schematic diagram of typical for car multimedia system application circuit. Right Speaker 1 Cs
Power Supply
Cc
VDD
100k 1k
Ci
Right Audio Input
3 VDD
Cs
VDD
Headphones
Ci
VDD Cc
1k
Power Supply
LPVDD
BYPASS
C(BYP)
LOUT-
SHUTDOWN
10
System Control
LPGND
LOUT+
Left Speaker
Page 6
UP
DOWN
t Figure 2 . How the volume change with respect to Up/Down timing cotrol VIN
UP
Vout VDD/2
2T
2T
Page 7
f-FREQUENCY-Hz
f-FREQUENCY-Hz
f-FREQUENCY-Hz
Po-Output Power-W
Page 8
Po-Output Power-W
Po-Output Power-W
f-FREQUENCY-Hz
f-FREQUENCY-Hz
Page 9
PACKAGE OUTLINE
SM7513S 16PIN SOP
D L
Unit : mm
16
9
0.381x45
1
1.271 typ.
8
0.406 typ.
0.203typ.
D1
A2
0.10max
A1
16
SYMBOLS A A1 D E H L
NOTES: 1. JEDEC OUTLINEN/A 2. DIMENSIONS DDOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.MOLD FLASH PROTRUSIONS AND GATE BURRS SHALL NOT EXCEED 0.15mm PER SIDE. 3. DIMENSION EDOES NOT INCLUDE INTER-LEAD FLASH, OR PROTRUSIONS. INTER-LEAD FLASH AND PROTRUSIONS SHALL NOT EXCEED 0.25mm PER SIDE.
Page 10
E1
1 e
8 b 1 8
Thermal Pad
0.127 TYP
GAUGE PLANE
A2
SEATING PLANE
0.25
= 0~8
0.05
L L1
SYMBOLS A A1 A2 b D E1 E e L1 L s
0.45 0.20 0
NOM. 1.00 5.00 4.40 6.40 BSC 0.65 BSC 1.00 REF 0.60
NOTES: 1. JEDEC OUTLINE: MO-153 AB/MO-153 ABT(THERMALLY VARIATIONS ONLY) 2. DIMENSIONS DDOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.MOLD FLASH PROTRUSIONS AND GATE BURRS SHALL NOT EXCEED 0.15mm PER SIDE. 3. DIMENSION EDOES NOT INCLUDE INTER-LEAD FLASH, OR PROTRUSIONS. INTER-LEAD FLASH AND
0.75 8
Page 11
E2
Ordering Information
Green Information
Package SOP-16 SSOP-16 Marking SM7513SG SM7513FG Green Part Number SM7513SG SM7513FG
Page 12