Sie sind auf Seite 1von 8

DPP B4

Kolej Kemahiran Tinggi MARA Pasir Mas, Kelantan.


JOB SHEET
PROGRAMME : SESSION : CODE/COURSE : DTEI JULY DEC 2011 DFT 4322 ELECTRONIC SOFTWARE APPLICATION 3 Hours MS. NORSYURIATIE ABD AZIZ PRINTED CIRCUIT BOARD DESIGN Netlist At the end of the lesson, students should be able to: LEARNING OUTCOME : 1. Using the Nets tab 2. Using the Netlist Editor. 1. Computer 2. Printer 3. Electronic Workbench Software - Ultiboard 10.0 SEMESTER : 4 SHEET NO : WEEK : VENUE : JS10 11 M17

NO OF STUDENTS : 4A DURATION : LECTURER : TOPIC : SUB-TOPIC :

TOOLS / EQUIPMENTS / MATERIALS :

DATA :

INSTRUCTION : This experiment is to approach the student by doing the practical base on the theory that has been learned before. By adapting the Page 1 of 8

DPP B4 theory the student should be able to do the experiment and implementation such as on safety, cleanliness, tidiness and etc. Using the Nets Tab The Nets buttons allow you to preview a net in relation to the board, find a net, highlight a selected net, lock and unlock a selected net, set the width and clearance of a selected net, and remove the copper of a selected net. Using the Netlist Editor The Netlist Editor can be used to view the nets in the design and to view the pads in the nets. You can also use the Netlist Editor to add nets to the design and remove nets from the design, as well as to add pads to or delete pads from an existing net.

PROCEDURE STEP KEY POINT


Safety : Make sure the wearing is suitable for the work. Avoid wear the metal materials. Avoid playing while doing work.

1. Open Ultiboard 2. Using Place/From Database

a. Open Ultiboard Circuit Window a. Please place an Arrays Resistor, Jumper and Led as in Figure 1

Figure 1

3. To open the Netlist Editor

a. Choose Tools/Netlist Editor. The Netlist Editor opens as in figure 2.

Page 2 of 8

DPP B4

PROCEDURE STEP KEY POINT

4. Adding a Net To add a net

Figure 2 a. Click Add Net on the Netlist editor. You are prompted to name the new net. b. Type a name for the net as L1. c. Click OK to save the new name or Cancel to cancel the operation. The new net appears in the Net drop-down list in the Netlist Editor, and in the Nets tab in the Design Toolbox.

5. Renaming a Net To rename a net


a. Select the net to be renamed from the list, or click from screen (at the top of the Netlist Editor) and select the net in the workspace. b. Click Rename net on the Netlist editor. The Give the name for the net box appear as Figure 3

Figure 3

c. Type a name for the net as N1. d. Click OK to save the new tab in the Design Toolbox.

Page 3 of 8

DPP B4

PROCEDURE STEP 6. Removing a Net To remove a net KEY POINT


a. Click remove net. The Select the net to delete Screen opens. b. Select the net to be deleted. c. Click Delete to delete the net.

Figure 4 The Select the Net to Delete screen closes and the net no longer appear in the Net drop-down list of the Netlist editor.

7. Adding a Pad To add a pad to a net:

a. Open the Netlist Editor b. In the Net drop-down list, select the net to which the pad will be added (N1), or click From Screen and select the net in the workspace. c. To add a pad from a list of available ones, click Add. The Add Pins to the Net screen opens as Figure 5. d. Select the pad to be added : Select R1, Pin 2 + Ctrl key and select L1,Pin A e. Click Add

Page 4 of 8

DPP B4

PROCEDURE STEP KEY POINT

8. To add a pad from the workspace

Figure 5 The Add Pins to the Net screen closes and the Netlist editor shows the added pad in the list of pads for the net displayed. The pad has also been made a part of the net in the board design. a. Add net (N1A) b. Click From Screen (at the bottom of the Netlist Editor) and select the pin in the workspace: i. Click L1, pin C ii. Click J1, pin 1 iii. The Netlist Editor shows the added pad in the list of pads for the net displayed and the net are displayed in the board design as in figure 6.

Figure 6

Page 5 of 8

DPP B4

PROCEDURE STEP 9. Deleting a Pad To deleting a pad from a net: KEY POINT
a. Open the Netlist Editor. b. In the Net drop-down list, select the net from which the pad will be deleted. c. Click Remove. The pad disappears from the list of pads for the net displayed.

RESULT :

Page 6 of 8

DPP B4

QUESTION/DISCUSSION : 1. Refer to the circuit below please create nets by using the Netlists Editor

Figure A

2. Using Database Manager, please create footprint for batteries to connect netlist for GND and VCC. 3. Your board design will shows netlist as Figure B below. Refer to the Figure B please add LED (L9) and Resistor (R1) and please create their netlist.

Figure B

Page 7 of 8

DPP B4

4. .

Please attach your work 1 to 3 in your lab report.

Wrap up your results from observations, data, and calculations and tie them to the objectives of the lab. Did it work? Why? What do your results mean? Did you prove your hypothesis or something different? Back up your explanations with scientific theories or information you have learned in class or found by research. Cite any sources of information that you use for research. If the lab didnt work for some reason, explain what went wrong. (Not more than 200 words)

ANSWER : ... ... ... ... ... ... ... ...

REFERENCE : 1. 2. 3. 4. 5. Mastering CAD/CAM with Engineering Subscription Ibrahim Zeid Mc Grawhill Applied Numerical Methods with MATLAB for engineering Steven Chopra Mc Grawhill I-Deas Student Guide EDS Mc Grawhill Mechanical Engineering Design Richard Budy Mc Grawhill Autodesk Inventor CP James Leake Mc Grawhill

Checked by : Signature : Name : Designation : Date :

Page 8 of 8

Das könnte Ihnen auch gefallen