Beruflich Dokumente
Kultur Dokumente
Interchangeability No. Temp. Class c = to 450F t = 451F & Above Orifice (D thru W) Non Bellows Pressure Class SRV
Material Class CC Carbon Steel is StandardNOTE 1 Deviation from Standard* Seat Design Lever/Cap Design Inlet Facing Service Disc Holder Pressure (Selected by Dresser) Sour Gas Guide Surface Coating
Pressure Class
05 06 10 12 14 16 18 20 22 24 26 28 = = = = = = = = = = = = 150 lb. 300 lb. 300 lb. 600 lb. 900 lb. 1500 lb. 2500 lb. 300 lb. 600 lb. 900 lb. 1500 lb. 2500 lb.
Seat Design
MS = Metal Seat DA = O-Ring TD = THERMODISC
Lever/Cap Design
31 32 33 34 35 36 37 = = = = = = = Screwed Bolted Packed Plain L Type R Type Air Operated
GI.15
19 05 -00 -J -c -2 -CC * -MS 06 -30 -t -C1 -DA -TD 10 -S2 Bellows 12 -S3 14 -S4 16 -M1 18 -MB (M1-1/2) -M2 20 -M3 22 -M4 24 -H1 26 -H2 28 -H3 -H4 -L1 -L2 -L3 -T1 -T2 -A1 -A2 -A3 -A4 -HA
-RF -GS -HP -SG1 -G1 -RJ -LA -LP -SG10 -G2 -LM -SS -SG5 -G3 -SM -SG15 -LF -SF Inlet Facing -LT RF = Raised Face/Serrated RJ = Ring Joint -ST LM = Large Male SM = Small Male -LG LF = Large Female -SG SF = Small Female LT = Large Tongue -LJ ST = Small Tongue LG = Large Groove -BW SG = Small Groove -GL LJ = Lens Joint BW = Butt Weld -OC
GL = Grayloc OC = OTECO
Service
GS = Gas LA = Liquid SS = Steam
Interchangeability No. Bonnet Orifice (D thru T) Non Bellows Pressure Class Safety Relief Valve
Deviation From Standard* Material Class - CC Carbon Steel is standard Disc Design Lever/Cap Design Inlet Facing Service Guide Surface Coating
* -CC -TD -31 NOTE 1 -32 -33 -34 -35 -36 -37
Pressure Class
05 = 150 lb. 06 = 300 lb. 10 = 300 lb. 12 = 600 lb. 14 = 900 lb. 16 = 1500 lb. 18 = 2500 lb. 20 = 300 lb. 22 = 600 lb. 24 = 900 lb. 26 = 1500 lb. 28 = 2500 lb.
Inlet Facing
RF RJ LM SM LF SF LT ST LG SG LJ BW GL OC = = = = = = = = = = = = = = Raised Face/Serrated Ring Joint Large Male Small Male Large Female Small Female Large Tongue Small Tongue Large Groove Small Groove Lens Joint Butt Weld Grayloc OTECO
-RF -SS -G1 -RJ -DT -G2 -LM -G3 -SM -LF -SF -LT -ST -LG -SG -LJ -BW -GL -OC
Bonnet
P1 = Closed P2 = Open
Disc Design
TD = Thermodisc
Lever/Cap Design
31 = Screwed 32 = Bolted 33 = Packed 34 = Plain 35 = L Type 36 = R Type 37 = Air Operated
Service
SS = Steam DT = Dowtherm
When * appears in code, nameplate will be stamped SPEC. NOTE 1: For other special material requirements, contact factory.
GI.16
General Information (SRV-1/Q4.05)