Beruflich Dokumente
Kultur Dokumente
GROUP 80A
CONFIGURATION DIAGRAMS
CONTENTS
OVERALL CONFIGURATION DIAGRAM. . . . . . . . . . . . . . . . . . . . . . HOW TO READ CONFIGURATION DIAGRAMS . . . . . . . . . . . . . . . . . . . . ENGINE COMPARTMENT. . . . . . . . . ENGINE AND TRANSAXLE . . . . . . . DASH PANEL . . . . . . . . . . . . . . . . . . . 80A-10 80A-2 FLOOR AND ROOF . . . . . . . . . . . . . . 80A-18 80A-3 80A-4 80A-6 DOOR . . . . . . . . . . . . . . . . . . . . . . . . . 80A-20 LIFTGATE . . . . . . . . . . . . . . . . . . . . . . 80A-22
80A-2
CONFIGURATION DIAGRAMS
OVERALL CONFIGURATION DIAGRAM
M1801000100536
REAR DOOR WIRING HARNESS * BATTERY WIRING HARNESS FUEL WIRING HARNESS
AC107467AB
NOTE: . 1. This illustration shows only major wiring harnesses. 2. *: also equipped at the right side.
TSB Revision
CONFIGURATION DIAGRAMS
HOW TO READ CONFIGURATION DIAGRAMS
80A-3
M1801000200566
The wiring harness diagrams clearly show the connector locations and harness routings at each site on actual vehicles.
Denotes connector No. The same connector No. is used throughout the circuit diagrams to facilitate connector location searches. The first alphabetical symbol indicates the location site of the connector and a number that follows is the unique number. Numbers are usually assigned to parts in clockwise order on the diagram. Example: A-19 Number specific to connector (serial number) Connector location site symbol A: ENGINE COMPARTMENT B: ENGINE AND TRANSAXLE C: DASH PANEL D: FLOOR AND ROOF E: DOOR F: LIFTGATE
A-19 Denotes ground point. Same ground number is used throughout circuit diagrams to facilitate search of ground point. Refer to GROUP 70 SINGLE PART INSTALLATION POSITION - GROUND MOUNTING LOCATIONS for details of ground points. FRONT WIRING HARNESS (RH) A-18 Denotes a section covered by a corrugated tube.
A-17
Denotes the color of the tube (If not specified, it is black). R: Red Y: Yellow
A-16 Y
The number of connector pins and the connector color (except milk white)* are shown for ease of retrieval. Example: (2-B) Connector color (milk white if no color is indicated) Number of connector pins *: Typical connector colors B: Black Y: Yellow L: Blue G: Green R: Red BR: Brown V: Violet O: Orange GR: Gray NONE: Milk white
A-15 A-15 (2) A-16 (2-GR) A-17 (2-B) A-18 (2-B) A-19 (2-GR) FOG LIGHT (RH) HORN (LOW) HEADLIGHT (RH) WINDSHIELD WASHER MOTOR DUAL PRESSURE SWITCH
TSB Revision
80A-4
CONFIGURATION DIAGRAMS
ENGINE COMPARTMENT
ENGINE COMPARTMENT
Connector symbol
A-01 A-02
M1801000301511
A
A-30 FRONT WIRING HARNESS (RH)
1
A-29
A-28
CONNECTOR COLOR CODE B: BLACK BR: BROWN G: GREEN GR: GRAY L: BLUE NONE: MILK WHITE O: ORANGE R: RED V: VIOLET Y: YELLOW
SIDE TURN SIGNAL LIGHT (RH) A/C PRESSURE SENSOR SIDE TURN SIGNAL LIGHT (LH) FOG LIGHT RELAY HORN RELAY ACCESSORY SOCKET RELAY FAN CONTROL RELAY FRONT-ECU
FRONT-ECU WHEEL SPEED SENSOR (FRONT: LH) (17-GR) FRONT WIRING HARNESS (LH) AND CONTROL WIRING HARNESS COMBINATION (3-GR) HEADLIGHT (LH) (3-B) FRONT COMBINATION LIGHT (LH)
TSB Revision
CONFIGURATION DIAGRAMS
ENGINE COMPARTMENT
80A-5
A-04
A-14
11
A-15
A-22
A-21
A-19
A-20
AC400323AB
FRONT IMPACT SENSOR (LH) FOG LIGHT (LH) FAN CONTROL MODULE THERMOMETER SENSOR HORN (HIGH) HORN (LOW) FOG LIGHT (RH) WINDSHIELD WASHER MOTOR
REAR WASHER MOTOR FRONT IMPACT SENSOR (RH) FRONT COMBINATION LIGHT (RH) HEADLIGHT (RH) WHEEL SPEED SENSOR (FRONT: RH) HEADLIGHT (RH) HEADLIGHT (LH)
TSB Revision
80A-6
CONFIGURATION DIAGRAMS
ENGINE AND TRANSAXLE
M1801000401154
B-01
B-02
B-03
B-04
B-30
B-29
CONNECTOR COLOR CODE B: BLACK BR: BROWN G: GREEN GR: GRAY L: BLUE NONE: MILK WHITE O: ORANGE R: RED V: VIOLET Y: YELLOW
AC400325AB
B-01 B-02 B-03 B-04 B-05 B-06 B-07 B-08 B-09 B-10X
(2-GR) (2-GR) (28-GR) (2-GR) (2-GR) (6-B) (5-GR) (4-GR) (2-GR) (1)
INJECTOR 1 INJECTOR 2 ABS-ECU INJECTOR 3 INJECTOR 4 THROTTLE POSITION SENSOR WINDSHIELD WIPER MOTOR MASS AIRFLOW SENSOR BRAKE FLUID LEVEL SWITCH ENGINE SPEED DETECTION CONNECTOR
B-13X (4) B-15X B-16X B-17X B-18 (4) (4) (4) (8-B)
THROTTLE ACTUATOR CONTROL MOTOR RELAY A/T CONTROL RELAY MFI RELAY A/C COMPRESSOR RELAY CONTROL WIRING HARNESS AND BATTERY WIRING HARNESS COMBINATION
TSB Revision
CONFIGURATION DIAGRAMS
ENGINE AND TRANSAXLE
80A-7
B-05
B-06
B-07
B-08
B-09
2 12
9 3
B-18
10
B-19
B-25
B-24
B-23
B-22
B-21
B-20
AC400326AB
(3-GR) OUTPUT SHAFT SPEED SENSOR (10-GR) A/T CONTROL SOLENOID VALVE ASSEMBLY (10-B) TRANSMISSION RANGE SWITCH (3-B) INPUT SHAFT SPEED SENSOR (1-B) OIL PRESSURE SWITCH (1) STARTER
STARTER A/C COMPRESSOR ASSEMBLY POWER STEERING PRESSURE SWITCH CRANKSHAFT POSITION SENSOR GENERATOR GENERATOR
TSB Revision
80A-8
CONFIGURATION DIAGRAMS
ENGINE AND TRANSAXLE
B-103
B-102
B-107 B-105
B-115
CONNECTOR COLOR CODE B: BLACK BR: BROWN G: GREEN GR: GRAY L: BLUE NONE: MILK WHITE O: ORANGE R: RED V: VIOLET Y: YELLOW
AC400325AC
EVAPORATIVE EMISSION PURGE SOLENOID KNOCK SENSOR MANIFOLD ABSOLUTE PRESSURE SENSOR ENGINE OIL PRESSURE SWITCH (FOR ENGINE OIL CONTROL VALVE)
TSB Revision
CONFIGURATION DIAGRAMS
ENGINE AND TRANSAXLE
80A-9
B-104
B-112
2 12
10
B-113
B-109
B-106
B-108
AC400326 AC
CAPACITOR ENGINE COOLANT TEMPERATURE SENSOR ENGINE COOLANT TEMPERATURE GAUGE UNIT IGNITION COIL 1
IGNITION COIL 2 ENGINE OIL CONTROL VALVE IGNITION COIL 4 IGNITION COIL 3 ACCELERATOR PEDAL POSITION SENSOR
TSB Revision
80A-10
CONFIGURATION DIAGRAMS
DASH PANEL
DASH PANEL
Connector symbol
M1801000601192
C-01
C-02
C-03
C-04
C-05
JUNCTION BLOCK
6
C-24
15
CONNECTOR COLOR CODE B: BLACK BR: BROWN G: GREEN GR: GRAY L: BLUE NONE: MILK WHITE O: ORANGE R: RED V: VIOLET Y: YELLOW
14
C-23
C-22
C-21
AC400328 AB
JOINT CONNECTOR (4) JOINT CONNECTOR (3) FOG LIGHT SWITCH COMBINATION METER COMBINATION METER A/C-ECU CLOCK BLOWER SWITCH AIR BAG MODULE (SQUIB) (PASSENGER'S SIDE)
INSTRUMENT PANEL WIRING HARNESS AND A/C WIRING HARNESS COMBINATION RESISTOR BLOWER MOTOR INSTRUMENT PANEL WIRING HARNESS AND FLOOR WIRING HARNESS (RH) COMBINATION
TSB Revision
CONFIGURATION DIAGRAMS
DASH PANEL
80A-11
C-06
C-07
C-08
C-09
C-11 Y
4
CONTROL WIRING HARNESS
C-12
C-13
5
Y
C-14
13
C-20 C-19 C-18 C-17 C-16 C-15
AC400329AB
C-14 C-15
C-16 C-17
FRONT WIRING HARNESS (RH) AND INSTRUMENT PANEL WIRING HARNESS COMBINATION (19-GR) INSTRUMENT PANEL WIRING HARNESS AND FRONT DOOR WIRING HARNESS (RH) COMBINATION (22-L) JOINT CONNECTOR (1) (13-GR) JOINT CONNECTOR (2)
(10)
HEATED OXYGEN SENSOR (FRONT) ACCESSORY SOCKET (2) ACCESSORY SOCKET (2) HAZARD WARNING SWITCH DATA LINK CONNECTOR DATA LINK CONNECTOR REMOTE CONTROLLED MIRROR SWITCH
TSB Revision
80A-12
DASH PANEL (CONTINUED)
CONFIGURATION DIAGRAMS
DASH PANEL
Connector symbol
C-101
JUNCTION BLOCK
C-119
C-118
C-117 CONNECTOR COLOR CODE B: BLACK BR: BROWN G: GREEN GR: GRAY L: BLUE NONE: MILK WHITE O: ORANGE R: RED V: VIOLET Y: YELLOW
15 14
INSTRUMENT PANEL WIRING HARNESS
C-116
AC400328AC
C-105 (22)
STOPLIGHT SWITCH RADIO AND CD PLAYER POWERTRAIN CONTROL MODULE INSTRUMENT PANEL WIRING HARNESS AND CONTROL WIRING HARNESS COMBINATION INSTRUMENT PANEL WIRING HARNESS AND CONTROL WIRING HARNESS COMBINATION
C-106 (19-GR) INSTRUMENT PANEL WIRING HARNESS AND CONTROL WIRING HARNESS COMBINATION C-107 (2) GLOVE BOX LIGHT C-108 (7) OUTSIDE/INSIDE AIR SELECTION DAMPER CONTROL MOTOR C-109 (27-GR) POWERTRAIN CONTROL MODULE C-110 (28-GR) POWERTRAIN CONTROL MODULE C-111 (29-GR) POWERTRAIN CONTROL MODULE
TSB Revision
CONFIGURATION DIAGRAMS
DASH PANEL
80A-13
C-121
C-102
C-122
C-104
C-105
C-106
C-107
C-120
C-108
4
C-109
C-110 Y C-111
13
C-123
C-115
C-114
C-113
C-103
C-112
AC400329AC
POWERTRAIN CONTROL MODULE IMMOBILIZER-ECU SRS-ECU SRS-ECU FRONT WIRING HARNESS (LH) AND INSTRUMENT PANEL WIRING HARNESS COMBINATION INSTRUMENT PANEL WIRING HARNESS AND FLOOR WIRING HARNESS (LH) COMBINATION INSTRUMENT PANEL WIRING HARNESS AND FRONT DOOR WIRING HARNESS (LH) COMBINATION
C-119 (6-L) C-120 (2) C-121 (3) C-122 (4) C-123 (20-Y)
RHEOSTAT CAPACITOR AIR BAG OFF INDICATOR LIGHT (PASSENGERS SIDE) SEAT BELT WARNING LIGHT (PASSENGERS SIDE) SRS-ECU
TSB Revision
80A-14
DASH PANEL (CONTINUED)
Connector symbol
CONFIGURATION DIAGRAMS
DASH PANEL
C-216
C-204
C-212
C-211
C-210
C-209
C-208
AC107474 AB
INSTRUMENT PANEL WIRING HARNESS AND JUNCTION BLOCK COMBINATION INSTRUMENT PANEL WIRING HARNESS AND JUNCTION BLOCK COMBINATION INSTRUMENT PANEL WIRING HARNESS AND JUNCTION BLOCK COMBINATION INSTRUMENT PANEL WIRING HARNESS AND JUNCTION BLOCK COMBINATION
C-205 (28) C-206 C-207 C-208 C-209 (5) (5) (5) (15)
C-210 (3)
INSTRUMENT PANEL WIRING HARNESS AND JUNCTION BLOCK COMBINATION DEFOGGER RELAY BLOWER RELAY POWER WINDOW RELAY FLOOR WIRING HARNESS (LH) AND JUNCTION BLOCK COMBINATION ROOF WIRING HARNESS AND JUNCTION BLOCK COMBINATION
TSB Revision
CONFIGURATION DIAGRAMS
DASH PANEL
80A-15
C-217 C-218
C-219
C-220 CONNECTOR COLOR CODE B: BLACK BR: BROWN G: GREEN GR: GRAY L: BLUE NONE: MILK WHITE O: ORANGE R: RED V: VIOLET Y: YELLOW
AC107475AB
NO CONNECTION NO CONNECTION FUEL PUMP RELAY (2) HEATED SEAT RELAY FUEL PUMP RELAY (1) NO CONNECTION
ETACS-ECU INSTRUMENT PANEL WIRING HARNESS AND ROOF WIRING HARNESS COMBINATION C-219 (24-GR) ETACS-ECU C-220 (24) ETACS-ECU
TSB Revision
80A-16
DASH PANEL (CONTINUED)
Connector symbol
CONFIGURATION DIAGRAMS
DASH PANEL
STEERING COLUMN
CLOCK SPRING
C-310 C-301 Y
C-309 C-302
C-307
C-306
C-305
C-304
AC107476AB
AUTO-CRUISE CONTROL SWITCH AUTO-CRUISE CONTROL SWITCH SUB HARNESS AND CLOCK SPRING WIRING HARNESS COMBINATION IGNITION SWITCH KEY REMINDER SWITCH HORN SWITCH
C-306 (4-Y) C-307 (4-Y) C-308 (6) C-309 (5) C-310 (10)
AIR BAG MODULE (SQUIB) (DRIVER'S SIDE) CLOCK SPRING CLOCK SPRING CLOCK SPRING AND CLOCK SPRING WIRING HARNESS COMBINATION COLUMN SWITCH
TSB Revision
CONFIGURATION DIAGRAMS
DASH PANEL
80A-17
NOTES
TSB Revision
80A-18
CONFIGURATION DIAGRAMS
FLOOR AND ROOF
M1801000901007
D-08
D
D-39 D-38 D-37
18
D-44 D-36 D-43 D-35 Y
Y Y
16
Y D-40
D-34
D-33
D-32
D-31
D-30
D-42
D-29
D-01 D-02 D-03 D-04 D-05 D-06 D-07 D-08 D-09 D-10
(10) (7) (7) (2) (6-B) (5) (2-R) (10) (3) (2-GR)
FLOOR WIRING HARNESS (RH) AND REAR DOOR WIRING HARNESS (RH) COMBINATION INSIDE REAR VIEW MIRROR ASSEMBLY INSIDE REAR VIEW MIRROR WIRING HARNESS AND ROOF WIRING HARNESS COMBINATION FRONT DOME LIGHT SUNROOF SWITCH SEAT BELT SWITCH (DRIVERS SIDE) SIDE AIR BAG MODULE (SQUIB) (LH) SUNROOF MOTOR ASSEMBLY REAR DOOR SWITCH (RH) REAR DOME LIGHT
D-11 D-12 D-13 D-14 D-15 D-16 D-17 D-18 D-19 D-20
(2) (2-B) (6) (3-B) (5-GR) (1) (1-B) (6) (3) (3-B)
FUEL LEVEL SENSOR (SUB) <AWD> WHEEL SPEED SENSOR (REAR: RH) REAR COMBINATION LIGHT (RH) FUEL LEVEL SENSOR <FWD>, FUEL TANK TEMPERATURE SENSOR <AWD> FUEL PUMP MODULE <FWD>, FUEL PUMP MODULE AND FUEL LEVEL SENSOR (MAIN) <AWD> ACCESSORY SOCKET (1) ACCESSORY SOCKET (1) REAR COMBINATION LIGHT (LH) REAR DOOR SWITCH (LH) FUEL TANK DIFFERENTIAL PRESSURE SENSOR
TSB Revision
CONFIGURATION DIAGRAMS
FLOOR AND ROOF
80A-19
D-09
D-10
D-11
D-13
D-14
D-15
D-17
D-18
17
D-19
D-26
D-25
D-24
D-23
D-22
D-21
AC107478AB
D-21 D-22 D-23 D-24 D-25 D-26 D-27 D-28 D-29 D-30 D-31
(2-B) (13) (10) (2) (3) (2-B) (18) (12-B) (3-B) (1-B) (4)
WHEEL SPEED SENSOR (REAR: LH) FLOOR WIRING HARNESS (LH) AND FUEL WIRING HARNESS COMBINATION FLOOR WIRING HARNESS (LH) AND REAR DOOR WIRING HARNESS (LH) COMBINATION SIDE IMPACT SENSOR (LH) FRONT DOOR SWITCH (LH) SEAT BELT PRE-TENSIONER (LH) AMPLIFIER FLOOR WIRING HARNESS (RH) AND FLOOR WIRING HARNESS (LH) COMBINATION HEATED SEAT ASSEMBLY (LH) PARKING BRAKE SWITCH HEATED OXYGEN SENSOR (REAR)
D-32 D-33 D-34 D-35 D-36 D-37 D-38 D-39 D-40 D-41 D-42 D-43 D-44
(3-B) (6) (9) (3-B) (2-R) (2) (3) (2-B) (2) (4-B) (2-GR) (3-GR) (3)
G SENSOR <ABS-AWD> SHIFT SWITCH ASSEMBLY HEATED SEAT SWITCH HEATED SEAT ASSEMBLY (RH) SIDE AIR BAG MODULE (SQUIB) (RH) SIDE IMPACT SENSOR (RH) FRONT DOOR SWITCH (RH) SEAT BELT PRE-TENSIONER (RH) ASHTRAY ILLUMINATION LIGHT FLOOR WIRING HARNESS (RH) AND FLOOR WIRING HARNESS (LH) COMBINATION SEAT SLIDE SENSOR OCCUPANT CLASSIFICATION-ECU SEAT BELT SWITCH (PASSENGERS SIDE)
TSB Revision
80A-20
CONFIGURATION DIAGRAMS
DOOR
DOOR
Connector symbol
M1801001400994
E
E-01 E-02
DRIVER'S SIDE
E-03
E-04
E-05
E-06
AC107479 AB
POWER WINDOW SUB SWITCH (REAR: LH) POWER WINDOW MOTOR (REAR: LH) DOOR LOCK KEY CYLINDER SWITCH (LH) POWER WINDOW MAIN SWITCH REMOTE CONTROLLED MIRROR (LH) TWEETER (LH) DOOR LOCK ACTUATOR (REAR: LH) REAR DOOR WIRING HARNESS (LH) AND REAR DOOR SUB WIRING HARNESS (LH) COMBINATION
E-12 E-13
(6-GR) (2)
REAR DOOR SPEAKER (LH) DOOR LOCK ACTUATOR (FRONT: LH) FRONT DOOR WIRING HARNESS (LH) AND FRONT DOOR SUB WIRING HARNESS (LH) COMBINATION POWER WINDOW MOTOR (FRONT: LH) FRONT DOOR SPEAKER (LH)
TSB Revision
CONFIGURATION DIAGRAMS
DOOR
80A-21
PASSENGER'S SIDE
E-14
E-15
E-16
E-17
E-18
E-19
FRONT DOOR WIRING HARNESS (RH) E-20 E-21 E-22 E-23 E-24 E-25
AC107480AB
TWEETER (RH) REMOTE CONTROLLED MIRROR (RH) POWER WINDOW SUB SWITCH (FRONT: RH) DOOR LOCK KEY CYLINDER SWITCH (RH) POWER WINDOW MOTOR (REAR: RH) POWER WINDOW SUB SWITCH (REAR: RH) FRONT DOOR SPEAKER (RH) POWER WINDOW MOTOR (FRONT: RH)
E-22
(8)
E-26
(6-B)
FRONT DOOR WIRING HARNESS (RH) AND FRONT DOOR SUB WIRING HARNESS (RH) COMBINATION DOOR LOCK ACTUATOR (FRONT: RH) REAR DOOR SPEAKER (RH) REAR DOOR WIRING HARNESS (RH) AND REAR DOOR SUB WIRING HARNESS (RH) COMBINATION DOOR LOCK ACTUATOR (REAR: RH)
TSB Revision
80A-22
CONFIGURATION DIAGRAMS
LIFTGATE
LIFTGATE
Connector symbol
M1801001900449
F-01
F-02
F-03
F-04
F-06
AC107481AB
DEFOGGER () REAR WIPER MOTOR HIGH-MOUNTED STOPLIGHT DEFOGGER (+) FLOOR WIRING HARNESS (LH) AND LIFTGATE WIRING HARNESS COMBINATION REAR SIDE MARKER LIGHT (RH) LIFTGATE LOCK ACUTUATOR
LIFTGATE SWITCH LICENSE PLATE LIGHT FLOOR WIRING HARNESS (LH) AND REAR BUMPER WIRING HARNESS COMBINATION EVAPORATIVE EMISSION VENTILATION SOLENOID REAR SIDE MARKER LIGHT (LH)
TSB Revision
52A-1
GROUP 52A
INTERIOR
CONTENTS
GENERAL DESCRIPTION. . . . . . . . . 52A-3
REMOVAL AND INSTALLATION . . . . . . . . DISASSEMBLY AND ASSEMBLY . . . . . . . 52A-18 52A-23
TRIMS . . . . . . . . . . . . . . . . . . . . . . . . . 52A-26
REMOVAL AND INSTALLATION . . . . . . . . 52A-26
ON-VEHICLE SERVICE. . . . . . . . . . .
PROCEDURES FOR CALIBRATING THE COMPASS . . . . . . . . . . . . . . . . . . . . . . . . . PROCESSES FOR ADJUSTING THE COMPASS VARIANCE. . . . . . . . . . . . . . . . AUTO-DIMMING FEATURE TEST . . . . . . .
52A-15
52A-15 52A-16 52A-16
HEADLINING . . . . . . . . . . . . . . . . . . . 52A-35
REMOVAL AND INSTALLATION . . . . . . . . 52A-35
52A-17 52A-18
Battery posts, terminals and related accessories contain lead and lead compounds. WASH HANDS AFTER HANDLING.
WARNINGS REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES
WARNING
Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver and passenger (from rendering the SRS inoperative). Service or maintenance of any SRS component or SRS-related component must be performed only at an authorized MITSUBISHI dealer. MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B - Supplemental Restraint System (SRS) before beginning any service or maintenance of any component of the SRS or any SRS-related component. NOTE The SRS includes the following components: SRS air bag control unit, SRS warning light, front impact sensors, air bag module, clock spring, and interconnecting wiring. Other SRS-related components (that may have to be removed/installed in connection with SRS service or maintenance) are indicated in the table of contents by an asterisk (*).
52A-2
INSIDE REAR VIEW MIRROR. . . . . . 52A-36
REMOVAL AND INSTALLATION . . . . . . . . 52A-36
52A-38
52A-38 52A-40 52A-41
52A-45
52A-45 52A-47
52A-51
INTERIOR
GENERAL DESCRIPTION
52A-3
M1521000100173
GENERAL DESCRIPTION
OPERATION
.
The compass detects the vehicle direction with the geomagnetic sensor built in the inside rear view mirror, and displays eight directions with the LCD. The ambient air temperature meter calculates the information from the thermo meter sensor, and displays the temperature with the LCD.
INSIDE REAR VIEW MIRROR WITH COMPASS AND TEMPERATURE DISPLAY CONSTRUCTION DIAGRAM
COMPASS DISPLAY TEMPERATURE DISPLAY
GEOMAGNETIC SENSOR
AC200085AB
TSB Revision
52A-4
INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS
M1521003200038
2. Verify that the condition described by the customer exists. 3. Find the malfunction by following the Symptom Chart. 4. Verify malfunction is eliminated.
SYMPTOM CHART
SYMPTOMS INSPECTION PROCEDURE NO. 1 2 3
M1521003500147
There is no display. The vehicle direction displayed on the compass is incorrect. The compass cannot be calibrated.
There is a discrepancy between the actual ambient air temperature 4 and displayed temperature, or an error (CS, OS) displays.
TSB Revision
INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS
52A-5
SYMPTOM PROCEDURES
JUNCTION BLOCK
CONNECTOR: D-03
CONNECTOR: C-210
AC200716AB
TSB Revision
52A-6
CONNECTOR: C-203
INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS
CONNECTOR: A-21
AC200724AB
AC200721AB
CONNECTOR: C-116
AC200722AB
CIRCUIT OPERATION
The power is constantly supplied to the inside rear view mirror (with compass and temperature display).
.
TROUBLESHOOTING HINTS Malfunction of the inside rear view mirror (with compass and temperature display) Damaged harness or connector
TSB Revision
INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS
52A-7
DIAGNOSIS
STEP 1. Check the inside rear view mirror (with compass and temperature display) power supply circuit at the inside rear view mirror connector D-03. (1) Remove the inside rear view mirror. Refer to P.52A-36. (2) Disconnect the inside rear view mirror connector D-03. (3) Turn the ignition switch to the "ON" position. (4) Check at inside rear view mirror harness side connector (front side) D-03. (5) Measure the voltage between terminal number 2 and ground. Voltage should measure 9 volts or more Q: Is the voltage between terminal number 2 and ground 9 volts or more? YES : Go to Step 4. NO : Go to Step 2.
CONNECTOR: D-03
D-03
2 1 7 6 5 4 3
AC201477AB
CONNECTOR: D-03
D-03
STEP 2. Check the inside rear view mirror connector D-03 connector for damage. Q: Is the inside rear view mirror connector D-03 is good condition? YES : Go to Step 3. NO : Repair or replace the connector. Go to Step 7.
AC200716AC
TSB Revision
52A-8
INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS
STEP 3. Check the wiring harness between the inside rear view mirror connector D-03 and ignition switch (IG2).
CONNECTOR: D-03 HARNESS SIDE CONNECTOR
D-03
AC200716AC
NOTE: Also check junction block connectors C-210 and C-203. If junction block connectors C-210 or C-203 is damaged, repair or replace the connector. Refer to GROUP 00E, Harness Connector Inspection P.00E-2. Q: Is the wiring harness between inside rear view mirror connector D-03 and ignition switch (IG2) in good condition? YES : Go to Step 6. NO : Repair the connector. Then go to Step 7.
C-210
TSB Revision
INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS
52A-9
CONNECTOR: D-03
STEP 4. Check the inside rear view mirror ground circuit at the inside rear view mirror connector D-03. (1) Remove the inside rear view mirror. Refer to P.52A-36. (2) Disconnect the inside rear view mirror connector D-03. (3) Check at inside rear view mirror harness side connector (front side) D-03. Q: Is the resistance between terminal 3 and ground less than 2 ohms? YES : Go to Step 7. NO : Go to Step 5.
D-03
AC201478AB
CONNECTOR: D-03
D-03
STEP 5. Check the inside rear view mirror connector D-03 connector for damage. Q: Is the inside rear view mirror connector D-03 in good condition? YES : Go to Step 6. NO : Repair or replace the connector. Go to Step 7.
AC200716AC
TSB Revision
52A-10
INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS
STEP 6. Check the wiring harness between inside rear view mirror D-03 and ground.
CONNECTOR: D-03 HARNESS SIDE CONNECTOR
D-03
AC200716AC
CONNECTOR: C-218
NOTE: Also check intermediate connector C-218. If intermediate connector C-218 is damaged. If intermediate connector C-218 is damaged, repair or replace the connector. Refer to GROUP 00E, Harness connector inspection P.00E-2. Q: Is the wiring harness between inside rear view mirror connector D-03 and ground in good condition? YES : Replace the inside rear view mirror. Refer to P.52A-36. Then go to Step 7. NO : Repair the wiring harness. Then go to Step 7.
STEP 7. Check the symptoms Q: Does the outside temperature meter and electronic compass display values normally? YES : The procedure is complete. (If no malfunctions are found in all steps, an intermittent malfunction is suspected. Refer to GROUP 00, How to Use Troubleshooting/Inspection Service Points How to Cope with Intermittent Malfunction P.00-14.) NO : Return to Step 1.
TSB Revision
INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS
52A-11
CIRCUIT OPERATION
The vehicle direction is displayed by the output of the geomagnetic sensor built into the outside temperature meter and electronic compass.
.
TROUBLESHOOTING HINTS
The calibration of the compass or compass variance failed.
DIAGNOSIS
The calibration of the compass or compass variance P.52A-15P.52A-16.
CIRCUIT OPERATION
Refer to P.52A-5.
DIAGNOSIS
Try to calibrate the compass at another location. 1. Move the vehicle to a wide, flat location. 2. Try again to calibrate the compass. NOTE: If the calibration is correct, the following causes can be assumed. Calibration is difficult due to the magnet direction and direction of the vehicle at the start of calibration. There is a disturbing magnetic field in the area. If the calibration is correct, check that the malfunction is eliminated. If the calibration is incorrect, replace the inside rear view mirror P.52A-36. Then, check that the malfunction is eliminated.
TSB Revision
52A-12
INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS
INSPECTION PROCEDURE 4: There is a Discrepancy Between the Actual Ambient Air Temperature and Displayed Temperature, or an Error (CS, OS) Displays.
. .
CIRCUIT OPERATION
A thermistor is used for the thermo meter sensor. The resistance value fluctuate according to ambient air temperature. The inside rear view mirror calculates ambient air temperature according to the changes in this resistance value, and displays it on the inside rear view mirror.
TROUBLESHOOTING HINTS
Malfunction of the thermo meter sensor Malfunction of the inside rear view mirror Damaged harness or connector
DIAGNOSIS
STEP 1. Check the thermo meter sensor internal resistance. 1.Remove the thermo meter sensor. Refer to P.51-10. 2.Check the internal resistance of the thermo meter sensor are at the standard values at temperature of 20C (68F) and 40C (104F). Standard value: Approximately 1,200 [at 20 C (68 F)] Approximately 500 [at 40 C (104 F)] Q: Does the thermo meter sensor resistance meet standard values above? YES : Go to Step 2. NO : Replace the thermo meter sensor. Then go to Step 6. STEP 2. Check connector A-21 at the thermo meter sensor for damage. Q: Is connector A-21 in good condition? YES : Go to Step 3. NO : Repair or replace the connector. Then go to Step 6.
THERMOMETER
SENSOR DRYER
AC003251AB
TSB Revision
INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS
52A-13
CONNECTOR: D-03
D-03
STEP 3. Check the input signal from the thermo meter sensor. (1) Remove the inside rear view mirror. Refer to P.52A-36. (2) Measure voltage from the rear side of the harness connector D-03 with the connector connected. (3) Turn the ignition switch to the "ON" position. (4) Measure voltage between terminal number 1 and number 4 when the thermo meter sensor is at the following temperatures. Voltage should measure approximately 2.90 volts [when 0C (32 F) is displayed] Voltage should measure approximately 1.86 volts [when 20C (68 F) is displayed] Voltage should measure approximately 1.10 volts [when 40C (104 F) is displayed] Q: Does the voltage between terminal number 1 and number 4 meet the above values? YES : Replace the inside rear view mirror. Refer to P.52A-36. Then go to Step 6. NO : Go to Step 4.
1 2 3 4 5 6 7
AC201482AB
CONNECTOR: D-03
D-03
STEP 4. Check the inside rear view mirror connector D-03 for damage. Q: Is inside rear view mirror connector D-03 in good condition? YES : Go to Step 5. NO : Repair or replace the connector. Then go to Step 6.
AC200716AC
TSB Revision
52A-14
INTERIOR
COMPASS AND TEMPERATURE DISPLAY DIAGNOSIS
CONNECTOR: C-116
STEP 5. Check the wiring harness between thermo meter sensor connector A-21 and inside rear view mirror connector D-03. NOTE: Also check intermediate connector C-218 and C-116. If intermediate connector C-218 or C-116 is damaged, repair or replace the connector. Refer to GROUP 00E, Harness Connector Inspection P.00E-2. Q: Is the wiring harness between thermo meter sensor connector A-21 and inside rear view mirror connector D-03 in good condition? YES : Go to Step 6. NO : Repair the wiring harness. Then go to Step 6.
9 8
7 6 5 15
4 3
2 1
C-116
2928 27 4039 38
AC305951AB
CONNECTOR: C-218
C-218
AC305952 AB
CONNECTOR: D-03
D-03
AC200716AC
TSB Revision
INTERIOR
ON-VEHICLE SERVICE
52A-15
STEP 6. Retest the system. Q: Is there any discrepancy between the actual ambient air temperature and displayed temperature, or is any error (CS, OS) displayed? YES : The procedure is complete.(If no malfunctions are found in all steps, an intermittent malfunction is suspected. Refer to GROUP 00, How to Use Troubleshooting/Inspection Service Points How to Cope with Intermittent Malfunction P.00-14). NO : Return to Step 1
ON-VEHICLE SERVICE
PROCEDURES FOR CALIBRATING THE COMPASS
1. Press the "COMP" button. The visual display is now in compass mode and the vehicle's directional heading (N, NE, E, SE, S, SW, W and NW) will be displayed. Pressing the "COMP" button a second time will turn off the visual display.
M1521007600016
AC003253
2. If the display reads "C," there may be a strong magnetic field interfering with the compass. In this case, the compass may need calibration.
AC003254
3. Drive the vehicle in a circle at about 5 mph (8km/h) or less until the display reads a direction.
AC003255
TSB Revision
52A-16
INTERIOR
ON-VEHICLE SERVICE
M1521007700013
1. Under certain circumstances, such as during a long distance cross-country trip, it will be necessary to adjust for compass variance. Compass variance is the difference between earth's magnetic north and true geographic north. If not adjusted to account for compass variance, the compass could give false readings. 2. Press the "COMP" button for more than 3 seconds. The current zone number will appear in the display.
AC003256
AC003257
3. Find the current location and variance zone number on the map on the left. 4. Press the "COMP" button until the new zone number appears in the display. After you stop pressing the button in, the display will show a compass direction within a few seconds. NOTE: Do not install a ski rack, antenna, etc. which are attached to the vehicle by means of a magnet. They affect the operation of the compass. NOTE: The compass may not indicate the correct compass point in the places shown below: Tunnels Areas along he railroad Underpass Transforming station Area with many office buildings Area over the subway Up or down a steep hill The compass returns to the correct compass point when the vehicle moves to an area where the geomagnetism in stabilized.
M1521007800010
1. Be sure the ignition is on and that the mirror is on. The green LED light to the right of the main display switch will be lit when the mirror is on. If it's not, depress the "TEMP" side of the main display switch for 15 seconds.
TSB Revision
INTERIOR
SPECIAL TOOL
BLACK CLOTH
52A-17
2. Cover the forward-facing light sensor on the back of the mirror with a black cloth. 3. While in a well-lit area, make sure light strikes the sensor on the front of the mirror, simulating glare from vehicles behind you. The mirror will dim within 2 minutes if the testing for the first time. If the mirror does not dim, replace the inside rear view mirror P.52A-36.
SPECIAL TOOL
TOOL TOOL NUMBER AND NAME MB990784 Ornament remover SUPERSESSION General service tool
M1521000600167
MB990784
TSB Revision
52A-18
REMOVAL AND INSTALLATION
WARNING
INTERIOR
INSTRUMENT PANEL ASSEMBLY
For removal and installation of the passenger's side air bag module, always observe the service procedures described in GROUP 52B, Air Bag Module and Clock Spring P.52B-360.
The following bolts and screws are used for installing the instrument panel. Bolts and screws are indicated as marks shown in the illustration in the sections of "Removal and Installation" and "Disassembly and Assembly." NAME TAPPING SCREW SYMBOL a b c d e MACHINE FLANGE SCREW WASHER ASSEMBLY BOLT f g SIZE (D L) mm 5 12 5 16 5 16 5 12 5 20 58 6 16 COLOR BLACK AC104417
AC104436 AC104450
SHAPE
h i j k l
5 20 (EARTH) 6 16 6 16 (EARTH) 8 20 10 60
AC200304
AC104416
TSB Revision
INTERIOR
INSTRUMENT PANEL ASSEMBLY
52A-19
CAUTION Refer to GROUP 52B-SRS Service Precautions P.52B-30 and Air bag Module and Clock Spring P.52B-360 before removing the passenger side air bag module.
Do not subject the SRS-ECU to any shocks when removing or installing the instrument panel.
Pre-removal and Post-installation Operation Removal and Installation of Front Floor Console (Refer to P.52A-24). Removal and Installation of Steering Wheel and Air Bag Module Assembly (Refer to GROUP 37, Steering Wheel P.37-22).
5
c d
4
d
2
d
3
d
AC106178
33
44 10 Nm 33 7 ft-lb d
32 13
l d
32
l
9
e
10
f
17
b b
20 18
b b
19 20
f
28
44 10 Nm 33 7 ft-lb
31 N
23 26
c g
14
16 15
k
25
a
24
b
29 30
12
k k k k k
22
a
21 27
11
AC400041AC
1.
<<A>>
2. 3. 4. 5. 6.
REMOVAL STEPS INSTRUMENT PANEL CLOCK GARNISH INSTRUMENT PANEL AIR OUTLET (CENTER) CLOCK INSTRUMENT PANEL DRIVERS SIDE GARNISH METER BEZEL COMBINATION METER HOOD LOCK RELEASE HANDLE (REFER TO GROUP 42, HOOD P.42-7).
<<A>>
REMOVAL STEPS (Continued) 7. INSTRUMENT PANEL PARCEL BOX FLOOR HARNESS (RH) AND JUNCTION BLOCK CONNECTION 8. INSTRUMENT LOWER PANEL 9. INSTRUMENT PANEL AIR OUTLET (LH) 10. INSTRUMENT LOWER PANEL BRACKET 11. INSTRUMENT PANEL DRIVER SIDE BRACKET
TSB Revision
52A-20
INTERIOR
INSTRUMENT PANEL ASSEMBLY REMOVAL STEPS (Continued) 12. KNEE ABSORBER (DRIVERS SIDE) 13. COLUMN COVER AIR MIX DOOR CABLE, BLOW VENT CHANGEOVER DAMPER CABLE CONNECTION (REFER TO GROUP 55, HEATER CONTROL ASSEMBLY AND A/C SWITCH P.55-83). 14. KNOB 15. CENTER PANEL 16. MANUAL AIR CONDITIONER CONTROL PANEL 17. AUDIO AND BOX ASSEMBLY 18. AUDIO 19. BOX 20. RADIO BRACKET 21. CENTER LOWER PANEL 22. ACCESSORY SOCKET 23. AIR BAG CUT-OFF SWITCH INDICATOR 24. SEAT BELT INDICATOR 25. CENTER LOWER BOX 26. CENTER LOWER COVER FRONT SCUFF PLATE, COWL SIDE TRIM (REFER TO P.52A-26). 27. BACK BONE SPACER 28. GLOVE BOX STOPPER 29. GLOVE BOX 30. KNEE ABSORBER (PASSENGERS SIDE) 31. CONNECTOR BLOCK 32. INSTRUMENT PANEL SIDE COVER DIN CABLE CLAMP <VEHICLE WITH AMPLIFIER> ROOF HARNESS CONNECTION INSTRUMENT PANEL HARNESS EARTH CONNECTION INSTRUMENT PANEL AND BODY HARNESS CONNECTION STEERING SHAFT HARNESS CONNECTOR AND CLAMP STOPLIGHT SWITCH HARNESS CONNECTOR (REFER TO GROUP 35A, BRAKE PEDAL P.35A-24). SRS-ECU HARNESS CONNECTOR (REFER TO GROUP 52B, SRS CONTROL UNIT (SRS-ECU) P.52B-357). SHIFT LOCK CABLE CLAMP STEERING SHAFT INSTALLATION BOLT (REFER TO GROUP 37, STEERING GEAR SHAFT ASSEMBLY P.37-24). 33. INSTRUMENT PANEL ASSEMBLY
>>A<<
TSB Revision
INTERIOR
INSTRUMENT PANEL ASSEMBLY
52A-21
A D D C C E G G F F H H E B B A
SECTION C C
INSTRUMENT PANEL
INSTRUMENT PANEL SIDE COVER SECTION D D INSTRUMENT PANEL SECTION E E CLIP CLIP METER BEZEL INSTRUMENT PANEL CLOCK GARNISH
INSTRUMENT PANEL DRIVER'S SIDE GARNISH SECTION F F CLIP INSTRUMENT LOWER PANEL
METER BEZEL
INSTRUMENT PANEL SECTION G G SECTION H H INSTRUMENT PANEL COLUMN COVER CLAW CLIP SECTION I I CLIP CENTER LOWER PANEL CENTER PANEL INSTRUMENT PANEL
AC400158AB
TSB Revision
52A-22
INTERIOR
INSTRUMENT PANEL ASSEMBLY
SPRING
The instrument panel air outlet may remain on the instrument panel side when disassembling the lower panel of the instrument panel and the instrument panel garnish. Carefully disassemble the parts remaining on the instrument panel side to prevent the ball and spring from falling. Assemble the ball and spring according to the figure to the left if they fall off.
AC103520AB
INSTALLATION SERVICE
.
TSB Revision
INTERIOR
INSTRUMENT PANEL ASSEMBLY
52A-23
M1521001900172
2
a
1
a
11
a
11
a
11
a a a
15
g g g
9
a g g j a
5
a g
14
12
13
a a a
AC106180AB
1. 2. 3. 4. 5. 6. 7. 8.
DISASSEMBLY STEPS SIDE DEFROSTER DUCT DEFROSTER NOZZLE ASSEMBLY DISTRIBUTION DUCT FRONT DECK CROSSMEMBER PASSENGERS SIDE AIR BAG MODULE BRACKET PASSENGERS SIDE AIR BAG MODULE PASSENGERS SIDE AIR BAG MODULE COVER GLOVE BOX STRIKER
DISASSEMBLY STEPS INSTRUMENT PANEL REINFORCEMENT METER BRACKET INSTRUMENT PANEL HOLDER INSTRUMENT PANEL UNDER COVER PASSENGERS SIDE SIDE AIR OUTLET ASSEMBLY (RH) CENTER COVER DRIVERS SIDE INSTRUMENT PANEL HARNESS CONNECTOR CLAMP INSTRUMENT PANEL
TSB Revision
52A-24
REMOVAL AND INSTALLATION
SECTION A A CLIP
INTERIOR
FLOOR CONSOLE ASSEMBLY
SECTION B B CLIP
FRONT FLOOR CONSOLE FRONT FLOOR CONSOLE LOWER SIDE COVER LOWER SIDE COVER
CLIP CLIP
3 4 5 2 1
C C
10
B A A
8
D D
9
11 2 Nm 98 17 in-lb
7
AC200402AB
1. 2. 3. 4. 5.
REMOVAL STEPS FRONT FLOOR CONSOLE PANEL HARNESS CONNECTOR <VEHICLE WITH HEATED SEAT> TRAY ASSEMBLY <VEHICLE WITHOUT HEATED SEAT> HEATED SEAT SWITCH TRAY <VEHICLE WITH HEATED SEAT> HEATED SEAT SWITCH <VEHICLE WITH HEATED SEAT>
REMOVAL STEPS (Continued) REAR FLOOR CONSOLE ASSEMBLY 7. REAR FLOOR CONSOLE BRACKET 8. FRONT FLOOR CONSOLE LOWER SIDE COVER 9. FRONT FLOOR CONSOLE 10. FRONT FLOOR CONSOLE BRACKET 6.
TSB Revision
INTERIOR
FLOOR CONSOLE ASSEMBLY
52A-25
M1521002400039
7 5 1 4 6 3 2 11
10
9 8
AC106397AH
1. 2. 3. 4. 5. 6.
DISASSEMBLY STEPS LID ASSEMBLY TRAY OUTER TRAY INNER LOCK KNOB LID INNER HINGE ASSEMBLY
DISASSEMBLY STEPS 7. LID COVER 8. HINGE SUPPORT BRACKET 9. REAR CONSOLE BOX 10. REAR CONSOLE 11. REAR CONSOLE PANEL
TSB Revision
52A-26
REMOVAL AND INSTALLATION
INTERIOR
TRIMS
TRIMS
M1521001100422
21
6 9
5 16
44 10 Nm 33 7 ft-Ib
20 15
19 14 17 18
44 10 Nm 33 7 ft-Ib
3 11
10
13
1. 2. FRONT SCUFF PLATE COWL SIDE TRIM REAR SEAT CUSHION (REFER TO P.52A-45). 3. REAR SCUFF PLATE 4. CENTER PILLAR TRIM LOWER 5. REAR DOOR OPENING TRIM 6. FRONT DOOR OPENING TRIM 7. FRONT SEAT BELT SHOULDER ANCHOR BOLT 8. CENTER PILLAR TRIM UPPER 9. FRONT PILLAR TRIM 10. REAR END TRIM 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21.
12
AC200062AB
<<A>>
PARCEL STRAP HOOK B REAR SEAT BOARD LUGGAGE FLOOR BOX VENTILATION CAP CONVENIENCE HOOK QUARTER TRIM CAP <VEHICLE WITHOUT TONNEAU COVER> PARCEL STRAP HOOK A QUARTER TRIM LOWER REAR SEAT BELT LOWER ANCHOR BOLT QUARTER TRIM UPPER CAP QUARTER TRIM UPPER
TSB Revision
INTERIOR
TRIMS
52A-27
D D B B
E E
C C C A A C
NOTE : CLIP POSITION SECTION A A CLIP SECTION B B SECTION C C FRONT SCUFF PLATE, REAR SCUFF PLATE SECTION D D CLIP
CLIP
FRONT PILLAR TRIM CLIP SECTION F F QUARTER TRIM LOWER QUARTER TRIM UPPER
AC305340 AC
TSB Revision
52A-28
.
INTERIOR
TRIMS
Unclip the front pillar trim and slide out it in the direction shown.
TSB Revision
INTERIOR
DOOR TRIM
52A-29
DOOR TRIM
REMOVAL AND INSTALLATION
<FRONT DOOR TRIM>
M1521006400343
2
A
1
NOTE :CLIP POSITION VIEW A B
SECTION B B CLIP
SECTION C C
1
CLIP
3
C
AC106408 AB
<<A>>
1. 2. 3.
REMOVAL STEPS SPEAKER GARNISH DOOR INSIDE HANDLE COVER DELTA COVER (REFER TO GROUP 51, DOOR MIRROR P.51-64). DOOR TRIM ASSEMBLY
TSB Revision
52A-30
<REAR DOOR TRIM>
INTERIOR
DOOR TRIM
2
A
1
NOTE : CLIP POSITION VIEW A B
3
C
CLIP
C
AC106406AB
<<A>>
1. 2. 3.
REMOVAL STEPS SPEAKER GARNISH DOOR INSIDE HANDLE COVER DOOR TRIM ASSEMBLY
TSB Revision
INTERIOR
DOOR TRIM
52A-31
1. Insert a flat-tipped screwdriver into the back end of the tapping screw cap of the door inside handle cover. 2. Try the screwdriver in the direction of the arrow. Remove the cap, then remove the tapping screw.
AC100003AF
3. Insert a special tool MB990784 in the gap between the door inside handle cover and door inside handle in the area shown. Then remove the thumb clamp of the door inside handle cover and door inside handle. 4. Insert a special tool from the back end of the door inside handle cover to lift it in the direction of the arrow. Then remove the door inside handle cover.
TSB Revision
52A-32
DISASSEMBLY AND ASSEMBLY
INTERIOR
DOOR TRIM
M1521006900036
<FRONT DOOR>
3 6 2 5
4
<REAR DOOR>
7 3 6 2 5 1
1
AC200071AB
1. 2. 3. 4.
DISASSEMBLY STEPS DOOR WEATHERSTRIP ARM REST ASSEMBLY POWER WINDOW SWITCH PANEL ASSEMBLY ARM REST
5. 6. 7.
TSB Revision
INTERIOR
LIFTGATE TRIM
52A-33
LIFTGATE TRIM
REMOVAL AND INSTALLATION
M1521008000062
1 2 2
4
AC313813 AD
1. 2.
3. 4.
TSB Revision
52A-34
CLIP AND CLAW POSITION
B B A A LIFTGATE SIDE TRIM E D D E
INTERIOR
LIFTGATE TRIM
C C
LIFTGATE PULL HANDLE F SECTION B B CLAW LIFTGATE SIDE TRIM CLAW SECTION C C SECTION D D LIFTGATE SIDE TRIM CLIP CLAW LIFTGATE LOWER TRIM SECTION G G G G LIFTGATE PULL HANDLE LIFTGATE LOWER TRIM
CLIP
CLIP
TSB Revision
INTERIOR
HEADLINING
52A-35
HEADLINING
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation Removal and Installation of Front Pillar Trim, Center Pillar Trim Upper, Quarter Trim Upper (Refer to P.52A-26).
SECTION A A CLAW
M1521001400490
9 9 8 2 7 1 6 4 5
A A B
3
SECTION B B CLIP
11, 12
12 10
B B
3
NOTE : CLIP POSITION
11 6 7 1
B
AC200309 AC
1. 2. 3. 4. 5.
<<A>>
6. 7.
REMOVAL STEPS ASSIST GRIP REAR DOME LIGHT ASSEMBLY HEADLINING COVER FRONT DOME LIGHT/MAP LIGHT ASSEMBLY SUN ROOF SWITCH COVER <VEHICLE WITH SUN ROOF> SUN VISOR HOLDER SUN VISOR ASSEMBLY
REMOVAL STEPS (Continued) 8. ROOF RAIL EDGE TRIM <VEHICLE WITH SUN ROOF> 9. HEADLINING 10. ROOF BRACKET 11. FRONT SIDE ROOF RIB 12. REAR SIDE ROOF RIB
AC005512 AD
TSB Revision
52A-36
REMOVAL AND INSTALLATION
INTERIOR
INSIDE REAR VIEW MIRROR
AC201221AB
<<A>>
REMOVAL STEPS (Continued) RADIATOR GRILLE LH <VEHICLES WITH COMPASS AND TEMPERATURE DISPLAY> (REFER TO GROUP 51, RADIATOR GRILLE P.51-10). 2. THERMO METER SENSOR <VEHICLES WITH COMPASS AND TEMPERATURE DISPLAY>
<Vehicles with compass and temperature display> Pull out the mirror in the bottom direction after turning it 90 degrees in the direction of the arrow, as shown.
TSB Revision
INTERIOR
INSIDE REAR VIEW MIRROR
52A-37
<Vehicles without compass and temperature display> 1. Disengage the claw A and lower the cover toward arrow 1 direction. 2. Push the claw B toward arrow 2 direction to unlock, and pull out the mirror toward arrow 3 direction.
AC209066 AC
TSB Revision
52A-38
REMOVAL AND INSTALLATION
WARNING
INTERIOR
FRONT SEAT ASSEMBLY
Before removing the front seat assembly, refer to GROUP 52B, Service Precautions
P.52B-30 and Air Bag Module and Clock Spring P.52B-360 <Vehicles without advanced air bag>, P.52B-360 <Vehicles with advanced air bag>. When removing and installing the front passenger seat, be sure to carry out accuracy check occupant classification sensor after the seat has been installed in the vehicle. (Refer to GROUP 52B, On-Vehicle Service P.52B-337.) <Vehicles with advanced air bag>
CAUTION Do not impact the seat. If the impact (falling etc.) is applied on the seat with occupant classification sensor, the occupant classification sensor transmitting error may be occurred.)
Pre-removal Operation Removal of Rear Floor Console Assembly (Refer to P.52A-24). Post-installation Operation Adjustment Procedures of Special Function (refer to GROUP 52B, On-Vehicle Service P.52B-337.) <Vehicles with advanced air bag> Installation of Rear Floor Console Assembly (Refer to P.52A-24).
11 1
44 10 Nm 33 7 ft-lb
44 10 Nm 33 7 ft-lb 33 5 m 22 4 ft-lb
SECTION A A
11
CLAW
11
3 4, 5
SECTION B B 44 10 Nm 33 7 ft-lb 33 5 m 22 4 ft-lb
8 9 6 7
A A
3
CLAW
10 11
NOTE : CLAW POSITIONS
5
B B
8 4
6 7
5
AC400278AB
TSB Revision
INTERIOR
FRONT SEAT ASSEMBLY 1. 2. 3. 4. 5. 6. 7. 8. HEAD RESTRAINT HEATED SEAT SWITCH FRONT SEAT ASSEMBLY REMOVAL STEPS FRONT SEAT ANCHOR COVER SEAT ANCHOR COVER OUTER SEAT ANCHOR COVER INNER SEAT BELT SWITCH CONNECTOR SIDE-AIR BAG MODULE CONNECTOR <VEHICLES WITH SIDE-AIR BAG HEATED SEAT CONNECTOR <VEHICLES WITH HEATED SEAT>
52A-39
FRONT SEAT ASSEMBLY REMOVAL STEPS (Continued) 9. SEAT SLIDE SENSOR CONNECTOR (DRIVERS SIDE) <VEHICLES WITH ADVANCED AIR BAG>, OCCUPANT CLASSIFICATION SENSOR CONNECTOR (PASSENGERS SIDE) <VEHICLES WITH ADVANCED AIR BAG> 10. OUTER SEAT BELT (PASSENGERS SIDE) <VEHICLES WITH ADVANCED AIR BAG> 11. FRONT SEAT ASSEMBLY
>>A<<
AC200581AB
TSB Revision
52A-40
INTERIOR
FRONT SEAT ASSEMBLY
M1522005500180
1 5, 3 8
2. Check that the indicator is lighted at HI or LO when battery voltage is supplied to terminal 5, and terminal 8 is grounded. 3. Check that indicator is lighted when battery voltage is supplied to terminals 2 and 6.
.
AC200099
1 2
AC200100
TSB Revision
INTERIOR
FRONT SEAT ASSEMBLY
52A-41
M1522001500627
WARNING
CLAW
27
10, 11
N 18
44 10 Nm 33 7 ft-lb
14 13 19
N 18
9 6 5
7 8
12 2 Nm 102 22 in-lb A
26
A
1 3 2 10 24 30
23 22 11
A A
24 29 27 28
25
AC401714 AB
1. 2. 3. 4. 5.
DISASSEMBLY STEPS RECLINING KNOB PIN HEIGHT ADJUSTER KNOB HEATER HARNESS ASSEMBLY FRONT SEAT CUSHION ASSEMBLY
6. 7. 8. 9.
DISASSEMBLY STEPS FRONT SEAT CUSHION COVER FRONT SEAT CUSHION PAD FRONT SEAT CUSHION FRAME SEAT CUSHION HEATER <VEHICLES WITH HEATED SEAT>
TSB Revision
52A-42
10. 11. 12. 13. 14.
INTERIOR
FRONT SEAT ASSEMBLY DISASSEMBLY STEPS RECLINING COVER SHIELD COVER FRONT SEATBACK ASSEMBLY LUMBAR SUPPORT CAP <VEHICLES WITH LUMBAR SUPPORT> LUMBAR SUPPORT LEVER <VEHICLES WITH LUMBAR SUPPORT> HEADREST GUIDE FRONT SEATBACK COVER FRONT SEATBACK PAD LUMBER SUPPORT CLIP <VEHICLES WITH LUMBAR SUPPORT> LUMBER SUPPORT <VEHICLES WITH LUMBAR SUPPORT> FRONT SEATBACK FRAME SEATBACK HEATER <VEHICLES WITH HEATED SEAT> INNER SEAT BELT SHAFT PIN SLIDE HANDLE SHAFT PROTECTER SLIDE SENSOR HARNESS SLIDE SENSOR BRACKET SLIDE SENSOR SEAT SLIDE ADJUSTER
<<A>>
15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30.
TSB Revision
INTERIOR
FRONT SEAT ASSEMBLY
52A-43
<RH SIDE>
WARNING Never attempt to disassemble or repair the occupant classification-ECU or the occupant
classification sensor. If faulty, replace it. Do not drop or subject the occupant classification-ECU and occupant classification sensor to impact or vibration. If denting, cracking, deformation, or rust are discovered in the occupant classification-ECU or the occupant classification sensor, replace it with a new occupant classification-ECU or the occupant classification sensor.
SECTION A A
10 15 12 13 11 14
CLAW
21
8, 9
44 10 Nm 33 7 ft-lb
2 7 4 5 3 6
A
20 17
A 44 10 Nm 33 7 ft-lb 7.6 0.7 Nm 102 22 in-lb
1 8 18 21
16
A A
19
1. 2. 3. 4. 5. 6. REMOVAL STEPS RECLINING KNOB HEATER HARNESS ASSEMBLY FRONT SEAT CUSHION ASSEMBLY FRONT SEAT CUSHION COVER FRONT SEAT CUSHION PAD FRONT SEAT CUSHION FRAME
18
7. 8. 9. 10. 11. 12. 13.
9
AC401743 AB
<<A>>
REMOVAL STEPS (Continued) SEAT CUSHION HEATER <VEHICLES WITH HEATED SEAT> RECLINING COVER SHIELD COVER FRONT SEATBACK ASSEMBLY HEADREST GUIDE FRONT SEATBACK COVER FRONT SEATBACK PAD
TSB Revision
52A-44
INTERIOR
FRONT SEAT ASSEMBLY REMOVAL STEPS (Continued) 14. FRONT SEATBACK FRAME 15. SEATBACK HEATER <VEHICLES WITH HEATED SEAT> 16. INNER SEAT BELT 17. SHAFT 18. PIN 19. SLIDE HANDLE 20. SHAFT PROTECTOR 21. SEAT SLIDE ADJUSTER
<<B>>
ACX01300
TSB Revision
INTERIOR
REAR SEAT ASSEMBLY
52A-45
44 10 Nm 33 7 ft-Ib
1 5
95 15 Nm 70 11 ft-Ib
44 10 Nm 33 7 ft-Ib 44 10 Nm 33 7 ft-Ib
3
44 10 Nm 33 7 ft-Ib
2 6
AC200090AB AC200090
1.
>>A<<
2. 3.
HEADREST REMOVAL STEPS REAR SEAT CUSHION ASSEMBLY INNER SEAT BELT AND CENTER SEAT BELT INSTALLATION BOLT
4. 5. 6.
REMOVAL STEPS (Continued) REAR SEATBACK ASSEMBLY LH REAR SEATBACK ASSEMBLY RH REAR SEAT HOOK
TSB Revision
52A-46
.
INTERIOR
REAR SEAT ASSEMBLY
AC005521AB
TSB Revision
INTERIOR
REAR SEAT ASSEMBLY
52A-47
M1522002000186
19 11 20 23 25 26 29 30 22
44 10 Nm 33 7 ft-Ib 44 10 Nm 33 7 ft-Ib
24 31 12
8 12 10 18 7 9
27
28
44 10 Nm 33 7 ft-Ib
17 16 15
32 2 3 21 28 14
13
44 10 Nm 33 7 ft-Ib
14 4
6 1N
5
AC200082AB AB
1. 2. 3. 4. 5. 6. 7. 8. 9.
REAR SEAT CUSHION DISASSEMBLY STEPS HOG RING REAR SEAT CUSHION COVER REAR SEAT CUSHION PAD REAR SEATBACK (LH SIDE) DISASSEMBLY STEPS ARM REST ASSEMBLY ARM REST CUP HOLDER ARM REST BOARD TETHER ANCHOR GARNISH RECLINING KNOB CAP
<<A>>
10. 11. 12. 13. 14. 15. 16. 17. 18. 19.
REAR SEATBACK (LH SIDE) DISASSEMBLY STEPS RECLINING KNOB GARNISH CENTER SEAT BELT GARNISH HEADREST GUIDE REAR SEATBACK COVER RECLINING COVER REAR SEATBACK PAD REAR SEATBACK FRAME ASSEMBLY ARM REST BUSHING RECLINING CABLE CENTER SEAT BELT COVER
TSB Revision
52A-48
20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32.
INTERIOR
REAR SEAT ASSEMBLY REAR SEATBACK (LH SIDE) DISASSEMBLY STEPS CENTER SEAT BELT RECLINING ADJUSTER REAR SEATBACK (RH SIDE) DISASSEMBLY STEPS TETHER ANCHOR GARNISH RECLINING KNOB CAP RECLINING KNOB GARNISH HEADREST GUIDE REAR SEATBACK COVER RECLINING ADJUSTER COVER REAR SEATBACK PAD REAR SEATBACK FRAME RECLINING CABLE RECLINING ADJUSTER
<<A>>
ACX01300
TSB Revision
INTERIOR
FRONT SEAT BELT
52A-49
CAUTION SRS: Before removing and installing the seat belts with pre-tensioner, refer to GROUP 52B Seat Belt with Pre-tensioner P.52B-372.
Pre-removal and Post-installation Operation Turn the ignition key to the LOOK (OFF) position. Disconnect the negative battery terminal.
5 6
44 10 Nm 33 7 ft-lb
2 4
<DRIVER'S SIDE>
44 10 Nm 33 7 ft-lb
44 10 Nm 33 7 ft-lb
4
<PASSENGER'S SIDE>
1
44 10 Nm 33 7 ft-lb
44 10 Nm 33 7 ft-lb
8
1.
AC400093 AB
2. 3. 4.
EXTENDER SEAT BELT ASSEMBLY* OUTER SEAT BELT REMOVAL STEPS SASH GUIDE COVER CENTER PILLAR TRIM LOWER (REFER TO P.52A-26). BRACKET OUTER SEAT BELT (REFER TO GROUP 52B-SEAT BELT WITH PRE-TENSIONER P.52B-372).
5. 6. 7. 8.
OUTER SEAT BELT REMOVAL STEPS (Continued) CENTER PILLAR TRIM UPPER (REFER TO P.52A-26). ADJUSTABLE SEAT BELT ANCHOR INNER SEAT BELT REMOVAL HARNESS CONNECTOR SHIELD COVER (REFER TO P.52A-41). INNER SEAT BELT
TSB Revision
52A-50
.
INTERIOR
REAR SEAT BELT
INSPECTION
M1523001400355
AC308221
44 10 Nm 33 7 ft-lb
6 7
3 4
44 10 Nm 33 7 ft-lb
44 10 Nm 33 7 ft-lb
1 2
AC107094AB
1. 2. 3.
REMOVAL STEPS REAR SEATBACK ASSEMBLY LH (REFER TO P.52A-45.) INNER SEAT BELT CENTER SEAT BELT INNER CENTER SEAT BELT GARNISH QUARTER TRIM UPPER (REFER TO P.52A-26.)
4. 5. 6. 7.
REMOVAL STEPS (Continued) CENTER SEAT BELT OUTER (REFER TO P.52A-47.) SEAT BELT SHOLDER ANCHOR BOLT SEAT BELT LOWER ANCHOR BOLT OUTER SEAT BELT
TSB Revision
INTERIOR
SPECIFICATIONS
52A-51
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATION
ITEM Center seat belt nut Front seatback frame bolt Front seat belt adjustable seat belt anchor bolt Front seat belt bolt Front seat bolt Front seat cushion frame bolt Front seat nut Front seat shaft bolt Instrument panel bolt Knee absorber bolt Rear floor console bracket bolt Rear seat belt bolt Rear seat bolt Rear seat nut Rear seat reclining adjuster bolt SPECIFICATION 44 10 Nm (33 7 ft-lb) 44 10 Nm (33 7 ft-lb) 44 10 Nm (33 7 ft-lb) 44 10 Nm (33 7 ft-lb) 44 10 Nm (33 7 ft-lb) 12 2 Nm (102 22 in-lb) 33 5 Nm (22 4 ft-lb) 7.6 0.7 Nm (67 6 in-lb) 44 10 Nm (33 7 ft-lb) 11 2 Nm (98 17 in-lb) 11 2 Nm (98 17 in-lb) 44 10 Nm (33 7 ft-lb) 44 10 Nm (33 7 ft-lb) 95 15 Nm (70 11 ft-lb) 44 10 Nm (33 7 ft-lb)
M1521004100131
TSB Revision
NOTES