0 Bewertungen0% fanden dieses Dokument nützlich (0 Abstimmungen)
127 Ansichten16 Seiten
Sections 10. And 10. Are first completed before the actual fault clearance procedure gets underway. If a fault clearance procedure is unsuccessful, Sections 10. To 10. Are performed. Card replacement is to be performed using the information specified in Register 9.
Sections 10. And 10. Are first completed before the actual fault clearance procedure gets underway. If a fault clearance procedure is unsuccessful, Sections 10. To 10. Are performed. Card replacement is to be performed using the information specified in Register 9.
Copyright:
Attribution Non-Commercial (BY-NC)
Verfügbare Formate
Als PDF, TXT herunterladen oder online auf Scribd lesen
Sections 10. And 10. Are first completed before the actual fault clearance procedure gets underway. If a fault clearance procedure is unsuccessful, Sections 10. To 10. Are performed. Card replacement is to be performed using the information specified in Register 9.
Copyright:
Attribution Non-Commercial (BY-NC)
Verfügbare Formate
Als PDF, TXT herunterladen oder online auf Scribd lesen
8 FauIt CIearance Procedures At the start of the fault clearance procedure, the Blank Form for Fault Clearance Record is copied from Section 10. Sections 10.1 and 10.2 are first completed before the actual fault clearance procedure gets underway. The fault clearance procedures are assigned to an alarm report using a reference number. f a number of different fault clearance procedures are specified under point "Remedy", these are to be performed in the specified order. f a fault clearance procedure is unsuccessful, Sections 10.3 to 10.5 are performed. n this case, the complete documents are sent to the Siemens service center where further fault clearance measures are performed. Card replacement is to be performed using the information specified in Register 9. The fault clearance procedures are arranged according to reference numbers. Ref.- Nr. ABM-Message OT-Message Cause Remedy SLT1/16 SLR16 0100 No alarms No alarms Fault-free system 1. No fault clearance! Fault clearance has been completed. 0105 Power fail PPP Voltage failure on the card suspected as being faulty. 1. Replace card suspected being faulty which is displayed in the card mounting position designation. The fault clearance procedure is complete. 0106 Power fail RRR Power fail 0110 Fuse alarm 60 V KKK Fuse alarm 60 V Redundant input voltage missing. 1. Check relevant fuse in the fuse panel. 2. Fuse faulty or switched off? f so, remedy error. The fault clearance procedure is complete. f not, refer to point 3. 3. Check voltage (35 V to 75 V) on the connection panel of the subrack. 4. Voltage present? f so, internal fault. Clarify with responsible Siemens department. f not, eliminate fault in the supply line. The fault clearance procedure is complete. 0115 Supervision fail PPP Monitoring fault on the card suspected of being faulty. 1. Replace card suspected of being faulty which is displayed in the card mounting position designation. The fault clear- ance procedure is complete. 0116 Supervision fail RRR Supervision fail 0120 Supervis. inact. Supervision inactive Monitoring fault on the ZW. All the ZW data have been deleted. 1. Reconfigure NE using the correct safeguarding file (main menu "Configuration", and submenu "File r NE"). The fault clearance procedure is complete. 0125 Card fail PPP Fault on the card suspected of being faulty. 1. Replace card suspected of being faulty which is displayed in the card mounting position designation. The fault clear- ance procedure is complete. 0126 Card fail RRR Card fail 0130 Not equipped. Card missing PPP Card either missing or not recognized. 1. Perform a required/actual equipping comparison using the OT (operating terminal) (main menu "Configuration", submenu "Equipping Options" and menu option "Compare Required/Actual Cards"). 2. nsert missing card or replace unrecognized card. The fault clearance procedure is complete. 0131 Card missing RRR Card missing Tab. 8.1 Fault Clearance Procedures 8 2 S42022-L3021-H1-2-7620 MMN Maintenance Synchronous Line Equipment SL16 0135 Wrong card type PPP Wrong card 1. Perform a required/actual equipping comparison using the OT (operating terminal) (main menu "Configuration", submenu "Equipping Options" and menu option "Compare Required/Actual Cards"). 2. Check configuration or replace incorrect card. n this case, the correct ordering No. can be determined from the loca- tion-specific diagrams. The fault clearance procedure ist complete. 0136 Wrong card type RRR Wrong card type 0140 Date/Time stop Date/Time stop Time stopped 1. Change ABM with defective clock. 2. Transmit correct OT (operating terminal) time to the network element after consulting the system specialist (main menu "Maintenance" and submenu "Date/Time"). The fault clearance procedure is complete. 0145 Battery low Battery low Low battery voltage 1. Does ABF correspond to variant S42024-L3236-A103? f so, refer to point 2. f not, refer to point 3. 2. nitiate battery change in ABF variant S42024-L3236-A103 by responsible Siemens service center. For further details, refer to point 4. 3. n the other variants, the battery compartment located on top of the ABF is opened by undoing two securing screws. Lift battery out of compartment and mark it. nsert new battery (lithium battery, rated voltage 3 V, Siemens ordering No. V42277-Z17-A1, corresponds to type CR AA from Varta) ensuring correct polarity while doing so! 4. Dispose of marked lithium battery properly! 5. Subsequently, check the date/time and adjust if neces- sary, see Point 6. 6. Transfer correct time of OT (operating terminal) to network element after clarifying with systems specialist (main menu Maintenance and submenu Date/Time). The fault clearance procedure is complete. 0150 Backplane-EEPROM Backpane EEPROM fail Backplane EEPROM disturbed. 1. Save configuration in file with aII options 2. Check and replace subrack EEPROM after consulting the responsible Siemens service center. 3. Reconfigure device (set basic type, activate internal moni- toring and transfer configuration file), see nstallation and Test Manual (TMN). The fault clearance procedure is complete. 0155 External alarm K External alarm kk External alarm 1. Define and evaluate external alarm using the location- specific diagrams. The fault clearance procedure is complete. 0200 Clock fail Timing source fail Central clock unit faulty 1. Replace central clock unit (203-TZ-1). The fault clearance procedure is complete. 0201 Clock fail RRR Timing source fail Clock failure in the optical transmitter (OS16R). 1. Replace the optical transmitter (OS16R). 2. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 3. 3. Replace the optical receiver (OE16R) of the same trans- mission direction. The fault clearance procedure is complete. Ref.- Nr. ABM-Message OT-Message Cause Remedy SLT1/16 SLR16 Tab. 8.1 Fault Clearance Procedures (Cont.) S42022-L3021-H1-2-7620 8 3 Maintenance Synchronous Line Equipment SL16 MMN 0210 Reference fail KKK SETS refer- ence fail Clock failure (T3in) on the central clock unit. 1. Check external clock (f = 2048 kHz, U = 0.5 V to 1.9 V bal.). 2. External clock working OK? f so, refer to point 3. f not, perform fault clearance on external clock source. The fault clearance procedure is complete. 3. Replace central clock unit (203-TZ-1). The fault clearance procedure is complete. 0215 Reference fail PPP SETS refer- ence fail (RxT3) Clock failure (F1in) on the central clock unit due to the performance or level in the F1in signal falling below required value. 1. Check the minimum performance (main menu "Mainte- nance", submenu "Central Clock Unit") to see whether a lower minimum performance is transmitted from the distant station (F1 side) due to clock or reference failure. 2. s the distant station (F1 side) transmitting a lower minimum performance? f so, refer to point 3. f not, refer to point 4. 3. The rest of the fault clearance procedure is performed in the distant station. The alarms of the distant station have to be evaluated. The fault clearance procedure on this device is thus complete. 4. Check the optical measured values (main menu "Perform- ance", submenu "Optical Measurements" to see whether the receive power has diminished compared to what it was during commissioning. 5. Has the receive power diminished? f so, refer to point 6. f not, refer to point 7. 6. n this case, it is necessary to check the line attenuation and to clean the fiber-optic connectors. The fault clear- ance procedure is complete. 7. Replace optical receiver. The fault clearance procedure is complete. 0220 Reference fail SETS refer- ence fail (RxLi) Clock failure (F2in) on the central clock unit due to the performance or level in the trib- utary signal falling below required value. 1. Check the minimum performance (main menu "Mainte- nance", submenu "Central Clock Unit") to see whether a lower minimum performance is transmitted from the distant station (F2 side) due to clock or reference failure. 2. s the distant station (F2 side) transmitting a lower minimum performance? f so, refer to point 3. f not, refer to point 4. 3. The rest of the fault clearance procedure is performed in the distant station. The alarms of the distant station have to be evaluated. The fault clearance procedure on this device is thus complete. 4. Exchange card MX4 which processes channel KKK. The fault clearance procedure is complete (see Tab. 5.2). 0225 Holdover SETS holdover The central clock unit is running in hold- over mode due to clock failure. 1. Process next alarm report (clock failure or reference failure). Ref.- Nr. ABM-Message OT-Message Cause Remedy SLT1/16 SLR16 Tab. 8.1 Fault Clearance Procedures (Cont.) 8 4 S42022-L3021-H1-2-7620 MMN Maintenance Synchronous Line Equipment SL16 0230 Loss of synchron. SETS synchron. fail Central clock unit cannot synchronize. 1. Replace central clock unit (203-TZ-1). 2. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 3. 3. Check reference clock (T3in, F1in and F2in); refer to fault clearance procedures 0210, 0215 and 0220. The fault clearance procedure on this device is complete. 0235 T3out squelched SETS T3out squelched Output clock (T3out) suppressed by the central clock unit due to the perfor- mance falling fallow the required level or due to refer- ence failure. 1. Determine configuration for minimum performance (Q min ) of external synchronization clock T3out (main menu "Configuration", submenu "Operating Parameters" and menu option "Central Clock Unit"). 2. Determine the reference in detail window "Status of External Synchronization Clock T3 out" (main menu "Maintenance", submenu "Central Clock Unit"). 3. f the reference is T1(line) or T1(trib), the performance level (Q X , X = 1 to 6) of the reference is determined from detail window "Synchronization Status". For reference T0, the performance level (Q X , X = 1 to 6) is determined from detail window "Status of System Clock (T0)". 4. s the performance level (Q X ) of the reference better than the required minimum performance (Q min ) of T3out (Q X } Q min )? f not (Q X > Q min ), refer to point 5. f so, replace central clock unit. The fault clearance procedure is complete. 5. s the reference T0? f so, refer to point 6 f not, check clock at the corresponding distant station. The fault clearance procedure on this device is complete. 6. Control clock pulse of T0 determined in detail window "Status of System Clock (T0)". 7. s T3in the control clock pulse of T0? f so, refer to point 8. f not, check the clock at the corresponding distant station. The fault clearance procedure on this device is complete. 8. Check the external clock source (f = 2048 kHz, U = 0.5 V to 1.9 V bal.) and the connection. The fault clearance procedure on this device is complete. 0300 Loss of signal Loss of signal (RxTr) No STM-1 signal or 140-Mbit/s signal at F2in. 1. Determine and check connection line. 2. s the connection line working properly? f so, refer to point 3. f not, perform fault clearance on connection line. 3. Loop output of the relevant channel to the input. 4. Fault eliminated? f so, refer to point 7. f not, refer to point 5. 5. Open loop and re-establish connections. 6. Replace card MX4 which processes channel KKK (see Tab. 5.2). The fault clearance procedure is complete. 7. Replace transmit card at the distant station. The fault clearance procedure at on this device is complete. Ref.- Nr. ABM-Message OT-Message Cause Remedy SLT1/16 SLR16 Tab. 8.1 Fault Clearance Procedures (Cont.) S42022-L3021-H1-2-7620 8 5 Maintenance Synchronous Line Equipment SL16 MMN 0305 Loss of frame Loss of frame (RxTr) Loss of synchronism of tributary side for STM-1 channel No. K. 1. Replace card MX4 which processes STM-1 channel KKKKK (see Tab. 5.2). 2. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 3. 3. Replace transmit card at the distant station. The fault clearance procedure at on this device is complete. 0310 B1-BER > SD B1-BER > SD (RxTr) Bit error ratio of the B1 parity byte on the trib- utary side exceeds the configured threshold value. 1. Check the configuration of the threshold values (main menu "AlarmStatus", submenu "SD Thresholds") against the commissioning protocol, and correct if necessary. 2. Wrong threshold values corrected? f so, the fault clearance procedure is complete. f not, the threshold value is correct, refer to point 3. 3. Check connection and line attenuation on the tributary side. 4. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 5. 5. Replace card MX4 which processes STM-1 channel KKKKK (see Tab. 5.2). 6. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 7. 7. Check transmitter at the distant station. The fault clearance procedure on this device is complete. 0315 B2-BER > SD B2-BER > SD (RxTr) Bit error ratio of the B2 parity byte on the trib- utary side is greater than the configured threshold value. 1. Check the configuration of the threshold values (main menu "AlarmStatus", submenu "SD Thresholds") against the commissioning protocol, and correct if necessary. 2. Wrong threshold values corrected? f so, the fault clearance procedure is complete. f not, the threshold value is correct, refer to point 3. 3. Check connection and line attenuation on the tributary side. 4. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 5. 5. Replace card MX4 which processes STM-1 channel KKKKK (see Tab. 5.2). 6. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 7. 7. Check transmitter at the distant station. The fault clearance procedure on this device is complete. 0320 B2-BER > 10E-h3 B2-BER > 10E-3 (RxTr) Bit error ratio of the B2 parity byte on the trib- utary side is >10 -3 . 1. Check connection and line attenuation on the tributary side. 2. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 3. 3. Replace card MX4 which processes STM-1 channel KKKKK (see Tab. 5.2). 4. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 5. 5. Check transmitter at the distant station. The fault clearance procedure on this device is complete. Ref.- Nr. ABM-Message OT-Message Cause Remedy SLT1/16 SLR16 Tab. 8.1 Fault Clearance Procedures (Cont.) 8 6 S42022-L3021-H1-2-7620 MMN Maintenance Synchronous Line Equipment SL16 0325 S-AS received Section-AS (RxTr) Section-AS received at trib- utary side. 1. Process alarm from the next NE in direction of signal source. 0330 FERF received MS-FERF (RxTr) Distant station receives no signal. 1. Check connection and line attenuation (DX4-O only). 2. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 3. 3. Replace card DX4 which processes the channel specified under KKKKK (see Tab. 5.2). The fault clearance procedure is complete. 0335 Loss of Pointer Loss off Ponter (RxTr) nvalid pointer value received at tributary side in AU4 of STM-1 channel No. K. 1. Replace card MX4 which processes channel KKKKK (see Tab. 5.2). 2. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 3. 3. Check transmitter at the distant station. The fault clearance procedure on this device is complete. 0340 No AU4 No AU4 (RxTr) llegal AU type (i.e. not AU4) in STM-1 channel No. KKKKK. 1. Check the setting of the distant station and replace trans- mit card if necessary. The fault clearance procedure is complete. 0345 P-AS received Path-AS (RxTr) Path-AS in the STM-1 signal received at trib- utary side. 1. Fault can only be eliminated at the distant station or at an NE earlier in the signal stream. The fault clearance procedure on this device is complete. 0350 AS received AS (RxTr) AS in the 140- Mbit/s signal received at trib- utary side. 1. Fault can only be eliminated at the distant station or at an NE earlier in the signal stream. The fault clearance procedure on this device is complete. 0355 Buffer fail Buffer fail (RxTr) Buffer (trans- mission memory) over- flow/underflow. 1. Configuration of central clock unit of optical transmitter (main menu Configuration, submenu Operating Param- eters and menu option Central Clock Unit) and correct if necessary. 2. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 3. 3. Replace card MX4 which processes channel KKKKK (see Tab. 5.2). 4. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 5. 5. Check the transmit card and central clock unit at the distant station and replace if necessary. The fault clearance procedure on this device is complete. 0400 Transmit degrad. PPP Transmit degraded (TxLi) Optical output power is 10 dB below the normal output power. 1. Replace optical transmitter specified in the card mounting position designation. The fault clearance procedure is complete. 0401 Transmit degrad. RRR 0405 Transmit fail PPP Transmit fail (TxLi) Failure of the optical signal on the card suspected of being faulty. 1. Replace card suspected of being faulty which is specified in the card mounting position designation. The fault clearance procedure is complete. 0406 Transmit fail RRR Ref.- Nr. ABM-Message OT-Message Cause Remedy SLT1/16 SLR16 Tab. 8.1 Fault Clearance Procedures (Cont.) S42022-L3021-H1-2-7620 8 7 Maintenance Synchronous Line Equipment SL16 MMN 0410 ALS active PPP Automatic laser shut- down unit active. 1. Undo fiber-optic connection at the optical receiver and measure the optical power at the fiber-optic connection. Measuring duration at least 70 s. 2. Was light present for 2 s during the 70 s? f so, refer to point 3. f not, refer to point 5. 3. Replace optical receiver for this line. 4. Fault eliminated? f so, the fault clearance procedure is complete. f not, repeat the fault clearance procedure at the distant station. The fault clearance procedure is complete. 5. Replace card OS16 at the distant station. 6. Fault eliminated? f so, the fault clearance procedure is complete. f not, line is disturbed. Fault clearance must be performed on the line. The fault clearance procedure is complete. 0411 ALS active RRR ALS active (TxLi) 0415 LD-bias high PPP Laser bias high (TxLi) Laser bias current of the optical trans- mitter (OS16 or OS16R) has exceeded the limit value. 1. Replace optical transmitter (OS16 or OS16R) specified in the card mounting position designation. The fault clearance procedure is complete. 0416 LD-bias high RRR 0420 LD mod. high PPP Laser mod. high (TxLi) Laser modula- tion current of the optical transmitter (OS16 or OS16R) has exceeded the limit value. 1. Replace optical transmitter (OS16 or OS16R) specified in the card mounting position designation. The fault clearance procedure is complete. 0421 LD mod. high RRR 0425 LD-power high PPP Opt. power high (TxLi) Optical output power of the optical trans- mitter (OS16 or OS16R) too high. 1. Replace optical transmitter (OS16 or OS16R) specified in the card mounting position designation. The fault clearance procedure is complete. 0426 LD-power high RRR 0500 Transmit degrad. PPP Output level low (TxLi) Required output power on the ONV suspected of being faulty is not guaran- teed. 1. Replace ONV at port PPP. The relevant mounting position number can be determined on the operating terminal (main menu "Configuration", submenu "Equipping Options" and menu option "Fiber Optical Amplifiers") or taken from the location-specific diagrams. The fault clearance procedure is complete. 0501 Transmit degrad. RRR 0505 Transmit fail PPP Transmit fail (TxLi) Optical output power on ONV suspected of being faulty is under +3 dBm. 1. Replace ONV at port PPP. The relevant mounting position number can be determined on the operating terminal (main menu "Configuration", submenu "Equipping Options" and menu option "Fiber Optical Amplifiers") or taken from the location-specific diagrams. The fault clearance procedure is complete. 0506 Transmit fail RRR Ref.- Nr. ABM-Message OT-Message Cause Remedy SLT1/16 SLR16 Tab. 8.1 Fault Clearance Procedures (Cont.) 8 8 S42022-L3021-H1-2-7620 MMN Maintenance Synchronous Line Equipment SL16 0510 LD-pump high PPP Laser pump current (TxLi) Laser pump current has exceeded the limit value. 1. Replace ONV at port PPP. The relevant mounting position number can be determined on the operating terminal (main menu "Configuration", submenu "Equipping Options" and menu option "Fiber Optical Amplifiers") or taken from the location-specific diagrams. The fault clearance procedure is complete. 0511 LD-pump high RRR 0515 nput level low PPP nput level too low on the card suspected of being faulty. 1. Check the optical measured values (main menu "Perform- ance", submenu "Optical Measurements") to see whether the transmit power of the optical transmitter at port PPP lies in the required range. Details of required values can be found in section 9 of the TED. 2. Does the optical transmit level lie in the required range? f so, refer to point 3. f not, refer to point 4. . Replace ONV card suspected of being faulty at port PPP. The relevant mounting position number can be deter- mined on the operating terminal (main menu "Configura- tion", submenu "Equipping Options" and menu option "Fiber Optical Amplifiers") or taken from the location- specific diagrams. The fault clearance procedure is complete. 4. Replace the optical transmitter card at port PPP. The fault clearance procedure is complete. 0516 nput level low RRR nput level low (only for ONV) 0600 Output level low PPP Output level too low on the card suspected of being faulty. Important: The line must be interrupted to eliminate the fault! 1. Disconnect the fiber-optic connector from the input of the OVV and use the optical level meter to measure the output level of the line. To do this, the laser restart for test in the SLT16 must be started at the far end if automatic laser shutdown (LSA) is active there. 2. s the optical level > 40 dBm? f so, refer to point 3. f not, refer to point 4. 3. Replace OVV at port PPP. The relevant mounting position number can be determined on the operating terminal (main menu "Configuration", submenu "Equipping Options" and menu option "Fiber Optical Amplifiers") or taken from the location-specific diagrams. The fault clearance procedure is complete. 4. Level } 40 dBm: Check fiber attenuation of the line. The fault clearance procedure is complete. 0601 Output level low RRR Output level low (only for OVV) 0605 LD pump current PPP Laser pump current has exceeded the limit value. 1. Replace OVV specified in the card mounting position des- ignation. The relevant mounting position number can be determined on the operating terminal (main menu "Con- figuration", submenu "Equipping Options" and menu option "Fiber Optical Amplifier") or taken from the location- specific diagrams. The fault clearance procedure is complete. 0606 LD pump current RRR Laser pump current (only for OVV) Ref.- Nr. ABM-Message OT-Message Cause Remedy SLT1/16 SLR16 Tab. 8.1 Fault Clearance Procedures (Cont.) S42022-L3021-H1-2-7620 8 9 Maintenance Synchronous Line Equipment SL16 MMN 0700 Loss of signal PPP Loss of signal (RxLi) No receive signal on the line side. 1. Undo fiber-optic connection at the optical receiver and measure the optical power at the fiber-optic connection. Measuring duration at least 70 s. 2. Was light present for 2 s during the 70 s? f so, refer to point 3. f not, refer to point 5. 3. Replace optical receiver for this line. 4. Fault eliminated? f so, the fault clearance procedure is complete. f not, repeat the fault clearance procedure at the distant station. 5. Replace card OS16 at the distant station (line side). 6. Fault eliminated? f so, the fault clearance procedure is complete. f not, line is faulty. Fault clearance must be performed on the line. The fault clearance procedure on this device is complete. 0701 Loss of signal RRR 0705 Loss of frame PPP Loss of frame (RxLi) Loss of synchronism (frame synchroniza- tion) on the card suspected of being faulty. 1. Replace card suspected of being faulty which is specified in the card mounting position designation. 2. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 3. 3. Replace the optical transmitter at the distant station. The fault clearance procedure on this device is complete. 0706 Loss of frame RRR 0710 Laser restart PPP Laser restart attempt (RxLi) Laser restart from the distant station. 1. Replace card OS16. 2. Fault eliminated? f so, fault clearance procedure complete. f not, repeat this fault clearance procedure at the distant station. 0711 Laser restart RRR 0715 B1-BER > SD PPP B1-BER > SD (RxLi) Bit error ratio of the B1 parity byte on the line side is greater than the config- ured threshold value. 1. Check the optical measured values (main menu "Perform- ance", submenu "Optical Measurements") to see whether the receive power has diminished compared to what it was during commissioning. 2. Has the receive power diminished compared to what it was during commissioning? f so, refer to point 3. f not, refer to point 4. 3. Check connection and line attenuation on the line side. 4. Check the configuration of the threshold values (main menu "AlarmStatus", submenu "SD Thresholds") against the commissioning protocol - correct if necessary. 5. Fault eliminated? f so, the threshold is correct, the fault clearance proce- dure is complete. f not, refer to point 6. 6. Replace card OE16 at port PPP. 7. Fault eliminated? f so, the fault clearance procedure is complete f not, refer to point 8. 8. Check optical transmitter at the distant station. The fault clearance procedure on this device is complete. 0716 B1-BER > SD RRR Ref.- Nr. ABM-Message OT-Message Cause Remedy SLT1/16 SLR16 Tab. 8.1 Fault Clearance Procedures (Cont.) 8 10 S42022-L3021-H1-2-7620 MMN Maintenance Synchronous Line Equipment SL16 0720 B2-BER > 10E-3 PPP B2-BER > 10E-3 (RxLi) Bit error ratio (B2 parity byte) on the line side is > 10 -3 . 1. Check the optical measured values (main menu "Perform- ance", submenu "Optical Measurements") to see whether the receive power has diminished compared to what it was during commissioning. 2. Has the receive power diminished compared to what it was during commissioning? f so, refer to point 3. f not, refer to point 4. 3. Check connection and line attenuation on the line side. 4. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 5. 5. Replace card OE16 at port PPP. 6. Fault eliminated? f so, the fault clearance procedure is complete f not, refer to point 7. 7. Check transmitter at the distant station. The fault clearance procedure on this device is complete. 0725 B2-BER > SD PPP B2-BER > SD (RxLi) Bit error ratio (B2 parity byte) on the line side is greater than the configured threshold value. 1. Check the optical measured values (main menu "Perform- ance", submenu "Optical Measurements") to see whether the receive power has diminished compared to what it was during commissioning. 2. Has the receive power diminished compared to what it was during commissioning? f so, refer to point 3. f not, refer to point 4. 3. Check connection and line attenuation on this side. 4. Check the configuration of the threshold values (main menu "AlarmStatus", submenu "SD Thresholds") against the commissioning protocol - correct if necessary. 5. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 6. 6. Replace card OE16 at port PPP. 7. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 8. 8. Check transmitter at the distant station. The fault clearance procedure is complete. 0730 S-AS received PPP Section-AS (RxLi) Section AS received. 1. Process alarm from next NE in the direction of the signal source. The fault clearance procedure on this device is complete. 0731 S-AS received RRR 0735 B1 inverted PPP B1 inverted (RxLi) B1 parity byte has been inverted in order to check the monitoring units. 1. B1 parity byte inversion can be canceled via the ABM (control group B) or the OT (main menu Configuration, sub menu "B1 nversion"). The fault clearance procedure is complete. 0736 B1 inverted RRR Ref.- Nr. ABM-Message OT-Message Cause Remedy SLT1/16 SLR16 Tab. 8.1 Fault Clearance Procedures (Cont.) S42022-L3021-H1-2-7620 8 11 Maintenance Synchronous Line Equipment SL16 MMN 0740 FERF received PPP MS-FERF (RxLi) Distant station on the line side has received a disturbed signal. Distur- bance has been reported by the distant station by means of the overhead byte (parity moni- toring of the multiplex section). 1. Process next alarm or alarm at the distant station. 0745 B1-ES count PPP B1-ES count high (RxLi) Configured B1-ES limit value exceeded on the line side. 1. Check the optical measured values (main menu "Perform- ance", submenu "Optical Measurements") to see whether the receive power has diminished compared to what it was during commissioning. 2. Has the receive power diminished compared to what it was during commissioning? f so, refer to point 3. f not, refer to point 4. 3. Check line attenuation and clean fiber-optic connectors. 4. Check the configuration of the threshold values (main menu "Performance", submenu "SD Thresholds") against the commissioning protocol - correct if necessary. 5. Check F1 performance data for B1 for the presence of error bursts (main menu "Performance", submenu "F1 Performance Data", menu option "Regenerator Section (B1)") and determine the cause. 0746 B1-ES count RRR 0750 B1-SES count PPP B1-SES count high (RxLi) Configured B1-SES limit value has been exceeded on the line side. 1. Check the optical measured values (main menu "Perform- ance", submenu "Optical Measurements") to see whether the receive power has diminished compared to what it was during commissioning. 2. Has the receive power diminished compared to what it was during commissioning? f so, refer to point 3. f not, refer to point 4. 3. Check line attenuation and clean fiber-optic connectors. 4. Check the configuration of the threshold values (main menu "Performance", submenu "Thresholds SES") against the commissioning protocol - correct if necessary. 5. Check F1 performance data for B1 for the presence of error bursts (main menu "Performance", submenu "F1 Performance Data", menu option "Regenerator Sec- tion (B1)") and determine the cause. 0751 B1-SES count RRR Ref.- Nr. ABM-Message OT-Message Cause Remedy SLT1/16 SLR16 Tab. 8.1 Fault Clearance Procedures (Cont.) 8 12 S42022-L3021-H1-2-7620 MMN Maintenance Synchronous Line Equipment SL16 0755 B2-ES count PPP B2-ES count high (RxLi) Configured B2-ES limit value has been exceeded on the line side. 1. Check the optical measured values (main menu "Perform- ance", submenu "Optical Measurements") to see whether the receive power has diminished compared to what it was during commissioning. 2. Has the receive power diminished compared to what it was during commissioning? 3. Check line attenuation and clean fiber-optic connectors. 4. Check the configuration of the threshold values (main menu "Performance", submenu "SD Thresholds") against the commissioning protocol - correct if necessary. 5. Check F1 performance data for B2 for the presence of error bursts (main menu "Performance", submenu "F1 Performance Data", menu option "Multiplex Section (B2)") and determine the cause. 0760 B2-SES count PPP B2-SES number high (RxLi) Configured B2-SES limit value has been exceeded on the line side. 1. Check the optical measured values (main menu "Perform- ance", submenu "Optical Measurements") to see whether the receive power has diminished compared to what it was during commissioning. 2. Has the receive power diminished compared to what it was during commissioning? f so, refer to point 3. f not, refer to point 4. 3. Check line attenuation and clean fiber-optic connectors. 4. Check the configuration of the threshold values (main menu "Performance", submenu "Thresholds") against the commissioning protocol - correct if necessary. 5. Check F1 performance data for B2 for the presence of error bursts (main menu "Performance", submenu "F1 Performance Data", menu option "Multiplex Section (B2)") and determine the cause. 0765 Protection fault Protect. switch fail 1. Check the configuration and correct if necessary. 2. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 3. 3. Replace the transmitter at the distant station. The fault clearance procedure on this device is complete. 0800 Loss of frame Loss of frame (RxLi) Loss of synchronism for STM-1 channel No. K (DX4 only). 1. Replace card DX4 which processes STM-1 channel KKKKK (see Tab. 5.2). 2. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 3. 3. Replace the transmitter at the distant station. The fault clearance procedure on this device is complete. 0815 Loss of pointer Loss of pointer (RxLi) nvalid pointer value received at line side in AU4 of STM-1 channel No. K. 1. Replace card DX4 which processes channel KKKKK (see Tab. 5.2). 2. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 3. 3. Replace the transmitter at the distant station. The fault clearance procedure on this device is complete. 0820 No AU4 No AU4 (RxLi) nvalid AU type (not AU4) in STM-1 channel No. K. 1. Fault can only be eliminated at the distant station or in an NE earlier in the signal stream. Ref.- Nr. ABM-Message OT-Message Cause Remedy SLT1/16 SLR16 Tab. 8.1 Fault Clearance Procedures (Cont.) S42022-L3021-H1-2-7620 8 13 Maintenance Synchronous Line Equipment SL16 MMN 0825 Path-AS received Path-AS (RxLi) Path-AS in STM-1 signal. 1. Fault can only be eliminated at the distant station or in an NE earlier in the signal stream. The fault clearance procedure on this device is complete. 0830 B3-BER > 7*10E-4 B3-BER > 7*10E-4 (RxLi) Bit error ratio of the B3 parity byte on the line side is >710 -4 in the STM-1 signal. 1. Are B1/B2 bit errors also reported? f so, perform fault clearance for these alarm reports (B1 or B2). f not, refer to point 2. 2. Faults can only be eliminated in a line section or in an NE earlier in the signal stream. The fault clearance procedure of this device is complete. 0835 B3-BER > SD B3-BER > SD (RxLi) Bit error ratio of the B3 parity byte on the line side is greater than the config- ured threshold value in the STM-1 signal. 1. Are B1/B2 bit errors also reported? f so, perform fault clearance for these alarm reports (B1 or B2). f not, refer to point 2. 2. Check the configuration of the thresholds (main menu "AlarmStatus", submenu "SD Thresholds") and correct if necessary. 3. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 3. 4. Faults can only be eliminated at the distant station or in an NE earlier in the signal stream. The fault clearance procedure on this device is complete. 0840 Path unequipped Path unequipped (RxLi) Undefined VC4 path in the STM-1 signal on the line side. 1. The alarm report depends on the configuration. t can only be eliminated at the distant station or in an NE earlier in the signal stream. The fault clearance procedure on this device is complete. 0845 FEBE-BER > SD Path-FEBE- BER > SD (RxLi) Bit error in the STM-1 signal on the line side is greater than the configured threshold value. 1. Fault can only be eliminated at the distant station or in an NE earlier in the signal stream. 0850 Path FERF Path-FERF (RxLi) VC4 path error in the STM-1 signal on the line side at the distant station. 1. Fault can only be eliminated at the distant station or in an NE in transmit direction. The fault clearance procedure on this device is complete. 0855 Path trace wrong Path trace wrong (RxLi) ncorrect VC4 path received in the STM-1 signal on the line side. 1. Check the configuration of the path trace (main menu "Configuration", submenu "Operating Parameters", menu option "Path Trace") and correct if necessary. 2. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 3. 3. Faults can only be eliminated at the distant station or in an NE earlier in the signal stream. The fault clearance procedure on this device is complete. Ref.- Nr. ABM-Message OT-Message Cause Remedy SLT1/16 SLR16 Tab. 8.1 Fault Clearance Procedures (Cont.) 8 14 S42022-L3021-H1-2-7620 MMN Maintenance Synchronous Line Equipment SL16 0900 Buffer fail Buffer fail (TxTr) Buffer (trans- mission memory) over- flow/underflow 1. Compare configuration of the central clock unit (main menu Configuration, submenu Operating Parameters, menu option Central Clock) and correct if necessary. 2. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 3. 3. Replace card DX4 which processes channel KKKKK (see Tab. 5.2). 4. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 5. 5. Check the transmit card and central clock unit at the dis- tant station and replace if necessary. The fault clearance procedure on this device is complete. 0905 LD-bias high Laser bias high (TxTr) Laser bias current of the optical demulti- plexer card has exceeded the limit value. 1. Replace optical card DX4-O which processes channel KKKKK (see Tab. 5.2). The fault clearance procedure is complete. 1000 F1OH clock failure SOH clock failure 1. Replace card suspected of being faulty which is displayed in the card mounting position designation. 2. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 3. 3. Check the transmit card, central clock unit and connection at the distant station and replace if necessary. The fault clearance procedure on this device is complete. 1001 F1OH clock failure RRR F1OH clock failure 1005 F1OH receive fail Receipt of error at an interna- tionally defined inter- face for SOH. 1. Check the distant station and connection. The fault clearance procedure on this device is complete. 1006 F1OH receive fail RRR F1OH receive fail 1010 F1AUX LOS KK Auxiliary signal not received (G.703). 1. Check connection. 2. Connection faulty? f so, eliminate fault. The fault clearance procedure is complete. f not, refer to point 3. 3. Check distant station. 1011 F1AUX LOS KK RRR Loss of signal (RxAux) 1015 F1AUX AS KK AS (G.703) (Channel 11, 21, 41, 12, 22 or 42) AS in auxiliary signal (G.703). 1. Fault at the distant station or in an upstream NE or line section. The fault clearance procedure on this device is complete. 1016 F1AUX AS KK RRR AS (G.703) (Channel 11, 21, 12 or 22) Ref.- Nr. ABM-Message OT-Message Cause Remedy SLT1/16 SLR16 Tab. 8.1 Fault Clearance Procedures (Cont.) S42022-L3021-H1-2-7620 8 15 Maintenance Synchronous Line Equipment SL16 MMN 1020 F1AUX wrong progr. Wrong channel program Undefined firm- ware in the channel program. 1. Check the configuration of the F1 auxiliary channels (main menu "Configuration", submenu "Operating Parameters", menu option "F1 Auxiliary Channels") and correct if necessary (see Tab. 8.2). 2. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 3. 3. Check firmware and repeat commissioning procedure after consulting responsible Siemens service center. The fault clearance procedure is complete. 1100 F2OH timing fail F2OH timing fail SOH clock failure 1. Replace card suspected of being faulty which is displayed in the card mounting position designation. 2. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 3. 3. Check the transmit card, central clock unit and connection at the distant station and replace if necessary. The fault clearance procedure on this device is complete. 1105 F2OH receive fail F2OH receive fail Receipt of error at the interna- tionally defined inter- face for SOH. 1. Fault at the distant station. The fault clearance procedure on this device is complete. 1110 F2 AUX LOS KK Los of signal (RxAux) Auxiliary signal not received (G.703). 1. Check connection. 2. Connection faulty? f so, eliminate fault. The fault clearance procedure is complete. f not, refer to point 3. 3. Check distant station. 1115 F2AUX AS KK AS (G.703) (Channel 1 or 2) AS in auxiliary signal (G.703). 1. Fault at the distant station or in an upstream NE or line section. The fault clearance procedure on this device is complete. 1120 F2AUX wrong prog. Wrong channel program Undefined firm- ware in the channel program. 1. Check the configuration of the F1 auxiliary channels (main menu "Configuration", submenu "Operating Parameters", menu option "F1 Auxiliary Channels") and correct if necessary (see Tab. 8.3). 2. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 3. 3. Check firmware and repeat commissioning procedure after consulting responsible Siemens service center. The fault clearance procedure is complete. 1205 SW download error KKK SW download error Error during SW download operation. 1. Repeat software loading procedure. 2. Fault eliminated? f so, the fault clearance procedure is complete. f not, contact the responsible Siemens service center. 1210 Routing data err. KKK Routing-data error Error in the routing data. 1. Reload routing tables (main menu "Configuration", submenu "File r NE") with category "Routing Tables MCF-Qx", see Operating Manual (OMN). 2. Fault eliminated? f so, the fault clearance procedure is complete. f not, contact the responsible Siemens service center. Ref.- Nr. ABM-Message OT-Message Cause Remedy SLT1/16 SLR16 Tab. 8.1 Fault Clearance Procedures (Cont.) 8 16 S42022-L3021-H1-2-7620 MMN Maintenance Synchronous Line Equipment SL16 1220 nterface fault KKK nterface fault Fault at the DCC or Q inter- face. The interface concerned is displayed via a code number in the alarm report. The code number is displayed in field KKK on the ABM, in column K on the OT. The signifi- cance of the code numbers is shown in Tab. 8.4. With code numbers 8 to 11, it is possible to determine the selected F2 port for each tributary group on the oper- ating terminal. Menu path: Configura- tion/Operating Parame- ters/F2 Auxil- iary Channels. 1. Check the configuration of the DCC settings (main menu "Configuration", submenu "DCC Settings") and/or Qx settings. 2. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 3. 3. Replace the card assigned to the code. 4. Fault eliminated? f so, the fault clearance procedure is complete. f not, refer to point 5. 5. Check the interface at the distant station. The fault clearance procedure on this device is complete. 6. Fault eliminated? f so, the fault clearance procedure is complete. f not, check DCN or TMN. The fault clearance procedure on this device is complete. 1225 NSAP address KKK NSAP address mismatch NSAP address incorrectly configured. 1. Repeat configuration procedure, refer to nstallation and Test Manual (TMN). 2. Fault eliminated? f so, the fault clearance procedure is complete. f not, contact the responsible Siemens service center. 1230 DCC config. wrong KKK DCC config. mismatch DCC interface configured incorrectly. 1. Repeat the configuration procedure (main menu "Config- uration, submenu "DCC Settings"), see nstallation and Test Manual (TMN). 2. Fault eliminated? f so, the fault clearance procedure is complete. f not, contact the responsible Siemens service center. 1250 Message No. KK Event report nn Signaling of a non-specified standard report. 1. Contact the responsible Siemens service center. The fault clearance procedure is complete. Ref.- Nr. ABM-Message OT-Message Cause Remedy SLT1/16 SLR16 Tab. 8.1 Fault Clearance Procedures (Cont.)