Beruflich Dokumente
Kultur Dokumente
Q2. RTS stands for: A. B. C. D. E. ready to start ready to switch request to send request to scan ready to set
Q3. In modem terminology, CD stands for: A. B. C. D. E. collect data call data cease deliver carrier detect comm detect
Q4. UART is a type of serial chip. Its letters stand for: A. B. C. D. E. unidirectional access regarding transmission universal asynchronous receiver/transmitter upper advanced real transfer unable all restore t-bits use all rom types
Q5. Select all true statements: A. B. C. D. E. com1 com1 com2 com2 com1 and and and and and com3 com4 com3 com4 com2 share share share share share the the the the the same same same same same IRQ IRQ IRQ IRQ IRQ
www.istepindia.com
Q6. In modems that support more than 300 baud, baud and bps do not mean the same thing. A. True B. false Q7. "bps" stands for bits per second. Baud is the number of discrete signals per second One discrete signal can encode more than one bit. Hence, a 9600 bps modem actually operates at 2400 baud. However, in common non-techie terminology, baud and bps are used synonymously, though that is not technically correct. These are all true statements. A. True B. false Q8. ________ is the term used to refer to the process of two modems establishing communications with each other. A. B. C. D. E. Interacting Handshaking Connecting Linking pinging
Q9. ISDN stands for: A. B. C. D. E. internal select data nulls integrated services digital network interval set down next interior sector direct none inferior sector data net
Q10. Your modem does not respond when you try to dial out. You try another modem
on another computer and get the same result. What is the most likely problem? A. B. C. D. E. defective modem defective computer software bug bad phone line virus
Q11. You have a serial scanner connected to your computer configured to use com3. It is turned
on. Your modem is using com1, and you can't dial out. What is the most likely problem? A. B. C. D. E. everything should work ok you have an i/o conflict you have a conflict with IRQ 4 you have a loose connection you have a conflict with IRQ 3
www.istepindia.com
Q13. What is the i/o address for com2? A. B. C. D. E. 2vb 2f8 8f8 330 e8e
Q14.What is the i/o address for com3? A. B. C. D. E. 3e8 345 ff8 5e8 be8
Q15.What is the i/o address for com4? A. B. C. D. E. 4e7 e8e be0 cb8 2e8
Q16.Before sending data, a modem sends a request to send signal, or RTS. A. True B. false Q17. ISDN uses _______________ technology. A. B. C. D. E. only digital digital and analog only analog neither digital nor analog mostly digital
www.istepindia.com
D. Multi E. scsi Q19. Modems use ________________ transmission. A. B. C. D. E. synchronous asynchronous timed interval ata bank
Q20.CD-Roms typically hold ______ of data. A. B. C. D. E. 100 meg 500 meg 650 meg 1000 meg 350 meg
Q21. Which of the following can cause CDs to be misread? Select all that apply. A. B. C. D. E. Smudges finger prints scratches cracks slight melting
Q22. CD-Rom drives typically have which of the following interfaces? Select all that apply. A. B. C. D. E. Serial Parallel Ide Scsi esdi
Q23. CD-Rom drives have which connectors? Select all that apply. A. B. C. D. E. Molex Berg data cable audio cable arcnet
Q24. In a computer with an eide adapter, where should you connect an ATA CD-Rom drive? A. B. C. D. E. on the floppy bus on the primary ide on the secondary ide on the scsi bus none of the above
www.istepindia.com
Q25.Your IDE CD-Rom drive is attached to the primary IDE adapter with our hard drive. How should its jumpers be set? A. B. C. D. E. as a master as a slave as neutral auto detect to 001
www.istepindia.com