Beruflich Dokumente
Kultur Dokumente
DESCRIPTION
The LTC2369-18 is a low noise, low power, high speed 18-bit successive approximation register (SAR) ADC. Operating from a 2.5V supply, the LTC2369-18 has a 0V to VREF pseudo-differential unipolar input range with VREF ranging from 2.5V to 5.1V. The LTC2369-18 consumes only 18mW and achieves 2.5LSB INL maximum, no missing codes at 18 bits with 96.5dB SNR. The LTC2369-18 has a high speed SPI-compatible serial interface that supports 1.8V, 2.5V, 3.3V and 5V logic while also featuring a daisy-chain mode. The fast 1.6Msps throughput with no cycle latency makes the LTC2369-18 ideally suited for a wide variety of high speed applications. An internal oscillator sets the conversion time, easing external timing considerations. The LTC2369-18 automatically powers down between conversions, leading to reduced power dissipation that scales with the sampling rate.
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and SoftSpan is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents including 7705765.
1.6Msps Throughput Rate 2.5LSB INL (Max) Guaranteed 18-Bit No Missing Codes Low Power: 18mW at 1.6Msps, 18W at 1.6ksps 96.5dB SNR (Typ) at fIN = 2kHz 120dB THD (Typ) at fIN = 2kHz Guaranteed Operation to 125C 2.5V Supply Pseudo-Differential Unipolar Input Range: 0V to VREF VREF Input Range from 2.5V to 5.1V No Pipeline Delay, No Cycle Latency 1.8V to 5V I/O Voltages SPI-Compatible Serial I/O with Daisy-Chain Mode Internal Conversion Clock 16-Lead MSOP and 4mm 3mm DFN Packages
APPLICATIONS
n n n n n n
Medical Imaging High Speed Data Acquisition Portable or Compact Instrumentation Industrial Process Control Low Power Battery-Operated Instrumentation ATE
TYPICAL APPLICATION
32k Point FFT fS = 1.6Msps, fIN = 2kHz
2.5V 10F VREF 0V 1.8V TO 5V 0.1F AMPLITUDE (dBFS) OVDD 0 20 40 60 80 100 120 140
236918 TA01a
+
LT6202
5.1 10nF
VDD IN+
SAMPLE CLOCK
2.5V TO 5.1V
160 180 0 100 200 300 400 500 600 700 800 FREQUENCY (kHz)
236918 TA01b
236918fa
Supply Voltage (VDD) ...............................................2.8V Supply Voltage (OVDD) ................................................6V Reference Input (REF).................................................6V Analog Input Voltage (Note 3) IN+, IN .........................(GND 0.3V) to (REF + 0.3V) Digital Input Voltage (Note 3) .......................... (GND 0.3V) to (OVDD + 0.3V) Digital Output Voltage (Note 3) .......................... (GND 0.3V) to (OVDD + 0.3V)
Power Dissipation .............................................. 500mW Operating Temperature Range LTC2369C ................................................ 0C to 70C LTC2369I .............................................40C to 85C LTC2369H .......................................... 40C to 125C Storage Temperature Range .................. 65C to 150C
PIN CONFIGURATION
TOP VIEW CHAIN VDD GND IN
+
1 2 3 4 5 6 7 8 17 GND
TOP VIEW CHAIN VDD GND IN+ IN GND REF REF 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 GND OVDD SDO SCK RDL/SDI BUSY GND CNV
DE PACKAGE 16-LEAD (4mm 3mm) PLASTIC DFN TJMAX = 150C, JA = 40C/W EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB
ORDER INFORMATION
LEAD FREE FINISH LTC2369CMS-18#PBF LTC2369IMS-18#PBF LTC2369HMS-18#PBF LTC2369CDE-18#PBF LTC2369IDE-18#PBF TAPE AND REEL LTC2369CMS-18#TRPBF LTC2369IMS-18#TRPBF LTC2369HMS-18#TRPBF LTC2369CDE-18#TRPBF LTC2369IDE-18#TRPBF PART MARKING* 236918 236918 236918 23698 23698 PACKAGE DESCRIPTION 16-Lead Plastic MSOP 16-Lead Plastic MSOP 16-Lead Plastic MSOP 16-Lead (4mm 3mm) Plastic DFN 16-Lead (4mm 3mm) Plastic DFN TEMPERATURE RANGE 0C to 70C 40C to 85C 40C to 125C 0C to 70C 40C to 85C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
236918fa
LTC2369-18
The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4)
SYMBOL VIN+ VIN VIN+ VIN IIN CIN CMRR PARAMETER Absolute Input Range (IN+) Absolute Input Range (IN) Input Differential Voltage Range Analog Input Leakage Current Analog Input Capacitance Input Common Mode Rejection Ratio Sample Mode Hold Mode fIN = 800kHz CONDITIONS (Note 5) (Note 5) VIN = VIN+ VIN
l l l l
ELECTRICAL CHARACTERISTICS
TYP
UNITS V V V A pF pF dB
45 5 80
The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4)
SYMBOL PARAMETER Resolution No Missing Codes Transition Noise INL DNL ZSE FSE Integral Linearity Error Differential Linearity Error Zero-Scale Error Zero-Scale Error Drift Full-Scale Error Full-Scale Error Drift (Note 7)
l
CONVERTER CHARACTERISTICS
CONDITIONS
l l l l l
MIN 18 18
TYP
MAX
1.3 (Note 6) (Note 7) 2.5 0.5 11 50 0.5 0.1 0 0.04 5 0.15 50 2.5 0.5 11
DYNAMIC ACCURACY
SYMBOL PARAMETER SINAD SNR
The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C and AIN = 1dBFS. (Notes 4, 8)
CONDITIONS fIN = 2kHz, VREF = 5V fIN = 2kHz, VREF = 5V, (H-Grade) Signal-to-Noise Ratio fIN = 2kHz, VREF = 5V fIN = 2kHz, VREF = 2.5V fIN = 2kHz, VREF = 5V, (H-Grade) fIN = 2kHz, VREF = 2.5V, (H-Grade)
l l l l l l l l l
MAX
UNITS dB dB dB dB dB dB
THD SFDR
Total Harmonic Distortion Spurious Free Dynamic Range 3dB Input Bandwidth Aperture Delay Aperture Jitter Transient Response
fIN = 2kHz, VREF = 5V fIN = 2kHz, VREF = 2.5V fIN = 2kHz, VREF = 5V
103 103
dB dB dB MHz ps ps ns
103
122 34 500 4
Full-Scale Step
200
236918fa
The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4)
CONDITIONS (Note 5) (Note 9)
l l
MIN 2.5
TYP 0.85
UNITS V mA
The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4)
SYMBOL PARAMETER VIH VIL IIN CIN VOH VOL IOZ ISOURCE ISINK High Level Input Voltage Low Level Input Voltage Digital Input Current Digital Input Capacitance High Level Output Voltage Low Level Output Voltage Hi-Z Output Leakage Current Output Source Current Output Sink Current IO = 500A IO = 500A VOUT = 0V to OVDD VOUT = 0V VOUT = OVDD
l l l
MIN
l l
TYP
UNITS V V A pF V
VIN = 0V to OVDD
V A mA mA
POWER REQUIREMENTS
SYMBOL VDD OVDD IVDD IOVDD IPD IPD PD PARAMETER Supply Voltage Supply Voltage Supply Current Supply Current Power Down Mode Power Down Mode Power Dissipation Power Down Mode Power Down Mode
The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4)
CONDITIONS
l l l l l
UNITS V V mA mA A A mW W W
1.6Msps Sample Rate 1.6Msps Sample Rate (CL = 20pF) Conversion Done (IVDD + IOVDD + IREF, VREF > 2V) Conversion Done (IVDD + IOVDD + IREF, VREF > 2V, H-Grade) 1.6Msps Sample Rate Conversion Done (IVDD + IOVDD + IREF, VREF > 2V) Conversion Done (IVDD + IOVDD + IREF, VREF > 2V, H-Grade)
The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4)
CONDITIONS
l l
TYP
UNITS Msps ns ns ns ns
l l l l l l l l
13 20 20 10 4
ns ns ns ns ns
236918fa
The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4)
CONDITIONS
l l l l l l l l l
MIN 4 4 1 13.5
TYP
MAX
UNITS ns ns ns ns
9.5 1 5 16 13
ns ns ns ns ns
Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may effect device reliability and lifetime. Note 2: All voltage values are with respect to ground. Note 3: When these pin voltages are taken below ground or above REF or OVDD, they will be clamped by internal diodes. This product can handle input currents up to 100mA below ground or above REF or OVDD without latch-up. Note 4: VDD = 2.5V, OVDD = 2.5V, REF = 5V, fSMPL = 1.6MHz. Note 5: Recommended operating conditions. Note 6: Integral nonlinearity is defined as the deviation of a code from a straight line passing through the actual endpoints of the transfer curve. The deviation is measured from the center of the quantization band.
Note 7: Zero-scale error is the offset voltage measured from 0.5LSB when the output code flickers between 00 0000 0000 0000 0000 and 00 0000 0000 0000 0001. Full-scale error is the deviation of the last code transition from ideal and includes the effect of offset error. Note 8: All specifications in dB are referred to a full-scale 5V input with a 5V reference voltage. Note 9: fSMPL = 1.6MHz, IREF varies proportionately with sample rate. Note 10: Guaranteed by design, not subject to test. Note 11: Parameter tested and guaranteed at OVDD = 1.71V, OVDD = 2.5V and OVDD = 5.25V. Note 12: tSCK of 10ns maximum allows a shift clock frequency up to 100MHz for rising capture.
tWIDTH 50%
236918 F01
236918fa
LTC2369-18
fSMPL = 1.6Msps, unless otherwise noted. Integral Nonlinearity vs Output Code
2.0 1.5 1.0 0.5 0.0 0.5 1.0 1.5 2.0 0 65536 131072 196608 OUTPUT CODE 262144
236918 G01
DC Histogram
40000 35000 30000 COUNTS 25000 20000 15000 10000 5000 = 1.3
0.1 0.0 0.1 0.2 0.3 0.4 0.5 0 65536 131072 196608 OUTPUT CODE 262144
236918 G02
160 0 25 50
THD 2ND
3RD
30
0
236918 G07
90 2.5
150 2.5
5
236918 G09
236918fa
INL/DNL vs Temperature
SNR SINAD
MIN DNL
0.5
MIN INL
1.0 55 35 15
0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 2.5 3 4.5 4 3.5 REFERENCE VOLTAGE (V) 5
236918 G18
90 CMRR (dB) 85 80 75
236918fa
236918fa
IN+
+
18-BIT SAMPLING ADC SPI PORT
IN
GND
236918 BD
TIMING DIAGRAM
Conversion Timing Using the Serial Interface
CHAIN, RDL/SDI = 0 CNV
BUSY
CONVERT
SCK
SDO
D7 D6
D5 D4 D3
D2 D1
D0
236918 TD01
236918fa
UNIPOLAR ZERO
FS 1LSB
236918 F02
ANALOG INPUT The analog inputs of the LTC2369-18 are pseudo-differential in order to reduce any unwanted signal that is common to both inputs. The analog inputs can be modeled by the equivalent circuit shown in Figure 3. The diodes at the input provide ESD protection. In the acquisition phase, each input sees approximately 45pF (CIN) from the sampling CDAC in series with 40 (RON) from the on-resistance of the sampling switch. The IN+ input draws a current spike while charging the CIN capacitor during acquisition. During conversion, the analog inputs draw only a small leakage current.
REF RON 40 CIN 45pF
IN+
REF IN RON 40
CIN 45pF
BIAS VOLTAGE
236918 F03
236918fa
10
High quality capacitors and resistors should be used in the RC filters since these components can add distortion. NPO and silver mica type dielectric capacitors have excellent linearity. Carbon surface mount resistors can generate distortion from self heating and from damage that may occur during soldering. Metal film surface mount resistors are much less susceptible to both problems. Pseudo-Differential Unipolar Inputs For most applications, we recommend the low power LT6202 ADC driver to drive the LTC2369-18. With a low noise density of 1.9nV/Hz and a low supply current of 3mA, the LT6202 is flexible and may be configured to convert signals of various amplitudes to the 0V to 5V input range of the LTC2369-18. To achieve the full distortion performance of the LTC2369-18, a low distortion single-ended signal source driven through the LT6202 configured as a unity-gain buffer as shown in Figure 4 can be used to get the full data sheet THD specification of 120dB. The LT6202 can also be used to buffer and convert large true bipolar signals which swing below ground to the 0V to 5V input range of the LTC2369-18. Figure 5a shows the LT6202 being used to convert a 10V true bipolar signal for use by the LTC2369-18. In this case, the LT6202 is configured as an inverting amplifier stage, which acts to attenuate and level shift the input signal to the 0V to 5V input range of the LTC2369-18. In the inverting configuration, the single-ended input signal source no longer directly drives a high impedance input. The input impedance is instead set by resistor RIN. RIN must be chosen carefully based on the source impedance of the signal source. Higher values of RIN tend to degrade both the noise and distortion of the LT6202 and LTC2369-18 as a system. Table 1 shows the resulting SNR and THD for several values of RIN, R1, R2, R3 and R4 in this configuration. Figure 5b shows the resulting FFT when using the LT6202 as shown in Figure 5a.
+
LT6202
5.1 10nF
IN+ LTC2369-18 IN
BW = 3.2MHz
236918 F04
Another filter network consisting of LPF2 should be used between the buffer and ADC input to both minimize the noise contribution of the buffer and to help minimize disturbances reflected into the buffer from sampling transients. Long RC time constants at the analog inputs will slow down the settling of the analog inputs. Therefore, LPF2 requires a wider bandwidth than LPF1. A buffer amplifier with a low noise density must be selected to minimize degradation of the SNR.
236918fa
11
ADC REFERENCE The LTC2369-18 requires an external reference to define its input range. A low noise, low temperature drift reference is critical to achieving the full datasheet performance of the ADC. Linear Technology offers a portfolio of high performance references designed to meet the needs of many applications. With its small size, low power and high accuracy, the LTC6655-5 is particularly well suited for use with the LTC2369-18. The LTC6655-5 offers 0.025% (max) initial accuracy and 2ppm/C (max) temperature coefficient for high precision applications. The LTC6655-5 is fully specified over the H-grade temperature range and complements the extended temperature operation of the LTC2369-18 up to 125C. We recommend bypassing the LTC6655-5 with a 47F ceramic capacitor (X5R, 0805 size) close to the REF pin. The REF pin of the LTC2369-18 draws charge (QCONV) from the 47F bypass capacitor during each conversion cycle. The reference replenishes this charge with a DC current, IREF = QCONV/tCYC. The DC current draw of the REF pin, IREF, depends on the sampling rate and output code. If the LTC2369-18 is used to continuously sample a signal at a constant rate, the LTC6655-5 will keep the deviation of the reference voltage over the entire code span to less than 0.5LSBs. When idling, the REF pin on the LTC2369-18 draws only a small leakage current (< 1A). In applications where a burst of samples is taken after idling for long periods as shown in Figure 6, IREF quickly goes from approximately 0A to a maximum of 1.1mA at 1.6Msps. This step in DC current draw triggers a transient response in the reference that must be considered since any deviation in the reference output voltage will affect the accuracy of the output
R2 499 10F R3 2k
R4 402 3
+
LT6202 1
5V 0V R1 499 200pF
236918 F05a
100 120 140 160 1 100 200 300 400 500 600 700 800 FREQUENCY (kHz)
236918 F05b
Figure 5b. 32k Point FFT Plot with fIN = 2kHz for Circuit Shown in Figure 5a
CNV
236918 F06
IDLE PERIOD
IDLE PERIOD
236918fa
12
REF
VDD
LTC2369-18
100 200 300 400 500 600 700 800 FREQUENCY (kHz)
236918 F08
Figure 7. A Schottky Diode Between REF and VDD Maintains REF > 2V for Applications Where the Reference May Be Powered Down
Total Harmonic Distortion (THD) DYNAMIC PERFORMANCE Fast Fourier Transform (FFT) techniques are used to test the ADCs frequency response, distortion and noise at the rated throughput. By applying a low distortion sine wave and analyzing the digital output using an FFT algorithm, the ADCs spectral content can be examined for frequencies outside the fundamental. The LTC2369-18 provides guaranteed tested limits for both AC distortion and noise measurements. Signal-to-Noise and Distortion Ratio (SINAD) The signal-to-noise and distortion ratio (SINAD) is the ratio between the RMS amplitude of the fundamental input frequency and the RMS amplitude of all other frequency components at the A/D output. The output is band-limited to frequencies from above DC and below half the sampling frequency. Figure 8 shows that the LTC2369-18 achieves a typical SINAD of 96.5dB at a 1.6MHz sampling rate with a 2kHz input. Signal-to-Noise Ratio (SNR) The signal-to-noise ratio (SNR) is the ratio between the RMS amplitude of the fundamental input frequency and
236918fa
Total Harmonic Distortion (THD) is the ratio of the RMS sum of all harmonics of the input signal to the fundamental itself. The out-of-band harmonics alias into the frequency band between DC and half the sampling frequency (fSMPL/2). THD is expressed as: THD= 20log V22 + V32 + V42 ++ VN2 V1
where V1 is the RMS amplitude of the fundamental frequency and V2 through VN are the amplitudes of the second through Nth harmonics. POWER CONSIDERATIONS The LTC2369-18 provides two power supply pins: the 2.5V power supply (VDD), and the digital input/output interface power supply (OVDD). The flexible OVDD supply allows the LTC2369-18 to communicate with any digital logic operating between 1.8V and 5V, including 2.5V and 3.3V systems.
13
200 400 600 800 1000 1200 1400 1600 SAMPLING RATE (kHz)
236918 F09
14
CONVERT CNV CHAIN LTC2369-18 RDL/SDI SCK CLK SDO DATA IN BUSY DIGITAL HOST IRQ
CONVERT
CONVERT
tSCKH 2 3 16 17 18
tQUIET
SCK
tSCKL
D1
D0
236918 F10
236918fa
15
RDLB RDLA CONVERT CNV CHAIN LTC2369-18 B RDL/SDI SCK SDO RDL/SDI SCK DATA IN CLK CNV LTC2369-18 A SDO
CHAIN
BUSY
CONVERT
CONVERT
tCNVL tCONV
RDL/SDIB tSCK SCK 1 2 3 tHSDO SDO tEN Hi-Z D17A D16A tDSDO D15A D1A tDIS D0A Hi-Z D17B D16B D15B D1B D0B Hi-Z
236918 F11
tSCKH 16 17 18 tSCKL 19 20 21 34 35 36
tQUIET
Figure 11. Normal Mode With Multiple Devices Sharing CNV, SCK and SDO
236918fa
16
number of converters. Figure 12 shows an example with two daisy-chained devices. The MSB of converter A will appear at SDO of converter B after 18 SCK cycles. The MSB of converter A is clocked in at the SDI/RDL pin of converter B on the rising edge of the first SCK.
CONVERT
CONVERT
tCYC tCNVL
CNV
BUSY tCONV tBUSYLH tSCKCH tSCKH 18 tHSDO tDSDO D1A D0A 19 20 tSCKL 34 35 tQUIET 36
SCK
3 tSSDISCK tHSDISCK
16
17
SDOA = RDL/SDIB
D17A tDSDOBUSYL
D16A
D15A
SDOB
D17B
D16B
D15B
D1B
D0B
D17A
D16A
D1A
D0A
236918 F12
236918fa
17
236918fa
18
236918fa
19
236918fa
20
R1 33 +3.3V C2 0.1F +3.3V C3 0.1F 1 +3.3V R46 U3 NL17SZ74 3 C56 0.1F 3 JP6 FS 1 2 3 +3.3V C13 0.8VREF 0.1F VREF 5 DB17 DB16 J2 CON-EDGE 40-100 R8 33 DC590 DETECT TO CPLD CLR\ Q\ PR\ Q 6 5 4 R4 7 33 4 CP GND 8 D VCC 2 +3.3V C4 0.1F 5 4 2 C11 0.1F R31 OPT V+ +3.3V U15 LT6202CS5 C7 0.1F OUT1 1 4 C39 0.01F R16 0 4 NPO 2 V R19 0 LTC2369-18 IN GND GND GND GND 5 RDL/SDI R7 1k 3 6 10 16 1 C65 OPT 0805 NPO R58 R35 OPT R38 OPT C40 OPT NPO IN+ VDD 2 OVDD 15 REF 7 8 REF CNV SCK SDO BUSY C58 OPT R45 C9 10F 6.3V C10 0.1F R32 5.1 +2.5V C6 10F 6.3V C20 47F 6.3V 0805 4 9V TO 10V
+3.3V
+3.3V C1 0.1F R2 1k
J1 CLKIN
BOARD LAYOUT
R5 49.9 1206
U2 R6 3 U8 3 NC7SZ04P5X NC7SVU04P5X 1k
U20 LTC6655AHMS8-5 8 SHDN GND 7 VIN OUT_F 6 GND OUT_S 5 GND GND 2 CNVST_33 FROM CPLD
COUPLING AC DC
C18 OPT
R15 OPT
R9 OPT
+2.5V
C8 1F
VREF/2
EXT C63 10F 6.3V C43 0.1F C44 1F C60 0.1F C59 1F 9V TO 10V
E7
HD1X3-100
EXT_CM
C46 1F
R40 OPT
COUPLING AC DC
JP5 HD1X3-100
J8 C49 OPT
AIN
R39 0
R41 OPT
+
HD1X3-100 U6 OPT NC7SZ66P5X 5 CNV VCC 9 2 B A 1 13 SCK OE 4 14 SDO GND 11 BUSY 3 12 RD +3.3V 4 5 3 U9 NC7SZ04P5X 2 R17 R13 2k 1k C15 0.1F J3 DC590 R10 4.99k SDO 1 3 5 7 9 11 13 2 4 6 8 10 12 14 U7 C14 0.1F 8 24LC025-I/ST VCC SCL SCK SDA WP CNV ARRAY A2 EEPROM A1 A0 VSS 4 6 5 7 3 2 1
J4 AIN+ 3 +IN1
R14 0
C17 10F
DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 DB8 DB9 DB10 DB11 DB12 DB13 DB14 DB15 CLKOUT C16 1 0.1F
39 37 35 33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1
40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2
R11 4.99k
R12 4.99k
236918 BL
LTC2369-18
21
236918fa
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE
DETAIL A 0 6 TYP
NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
236918fa
22
236918fa
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
23
+
V 2
LTC2369-18 IN
236918 TA02
10V 0V 10V
RIN 2k
R1 499 220pF
3V
RELATED PARTS
PART NUMBER ADCs LTC2379-18/LTC2378-18 LTC2377-18/LTC2376-18 LTC2380-16/LTC2378-16 LTC2377-16/LTC2376-16 LTC2383-16/LTC2382-16/ LTC2381-16 LTC2393-16/LTC2392-16/ LTC2391-16 LTC2355-14/LTC2356-14 LTC2366 DACS LTC2757 LTC2641 LTC2630 References LTC6655 LTC6652 Amplifiers LT6202/LT6203 LT6200/LT6200-5/ LT6200-10 LTC1992 LT6360 DESCRIPTION 18-Bit, 1.6Msps/1Msps/500ksps/250ksps Serial, Low Power ADC 16-Bit, 2Msps/1Msps/500ksps/250ksps Serial, Low Power ADC 16-Bit, 1Msps/500ksps/250ksps Serial, Low Power ADC 16-Bit, 1Msps/500ksps/250ksps Parallel/Serial ADC 14-Bit, 3.5Msps Serial ADC 12-Bit, 3Msps Serial ADC 18-Bit, Single Parallel IOUT SoftSpan DAC 16-Bit/14-Bit/12-Bit Single Serial VOUT DACs 12-Bit/10-Bit/8-Bit Single VOUT DACs Precision Low Drift Low Noise Buffered Reference Precision Low Drift Low Noise Buffered Reference Single/Dual 100MHz Rail-to-Rail Input/Output Noise Low Power Amplifiers 165MHz/800MHz/1.6GHz Op Amp with Unity Gain/AV = 5/AV = 10 Low Power, Fully Differential Input/Output Amplifier/ Driver Family Low Noise SAR ADC Driver with True Zero Output COMMENTS 2.5V Supply, Differential Input, 101.2dB SNR, 5V Input Range, DGC, Pin-Compatible Family in MSOP-16 and 4mm 3mm DFN-16 Packages 2.5V Supply, Differential Input, 96.2dB SNR, 5V Input Range, DGC, Pin-Compatible Family in MSOP-16 and 4mm 3mm DFN-16 Packages 2.5V Supply, Differential Input, 92dB SNR, 2.5V Input Range, PinCompatible Family in MSOP-16 and 4mm 3mm DFN-16 Packages 5V Supply, Differential Input, 94dB SNR, 4.096V Input Range, PinCompatible Family in 7mm 7mm LQFP-48 and QFN-48 Packages 3.3V Supply, 1-Channel, Unipolar/Bipolar, 18mW, MSOP-10 Package 2.35V to 3.6V Supply 6- and 8-Lead TSOT-23 Packages 1LSB INL/DNL, Software-Selectable Ranges, 7mm 7mm LQFP-48 Package 1LSB INL/DNL, MSOP-8 Package, 0V to 5V Output SC70 6-Pin Package, Internal Reference, 1LSB INL (12 Bits) 5V/2.5V, 5ppm/C, 0.25ppm Peak-to-Peak Noise, MSOP-8 Package 5V/2.5V, 5ppm/C, 2.1ppm Peak-to-Peak Noise, MSOP-8 Package 1.9nVHz, 3mA Maximum, 100MHz Gain Bandwidth Low Noise Voltage: 0.95nV/Hz (100kHz), Low Distortion: 80dB at 1MHz, TSOT23-6 Package 1mA Supply Current Low Noise Integrated Charge Pump
236918fa