Beruflich Dokumente
Kultur Dokumente
01
CUSTOMER BENEFITS
Complete protection for motors Comprehensive selection of protection functions for asynchronous circuit breaker controlled motors. Temperature measurement Interface to external VIO 12A RTD input module for twelve Pt, Ni or Cu temperature sensors. The external module enables the sensor connection point to be close to the motor, minimising sensor cable length. Measurements are transferred to the relay via RS485 or optical interface for the required protection stages, logic or measurements. Ultra-fast arc ash protection VAMP motor protection has an unique integrated arc fault protection functionality for enhanced safety of the motor termination box, switchgear as well as people and other property. This optional arc flash protection module enables the protection relay to become a part of the substation level arc flash protection system. Comprehensive measurements Motor control, measurement of electrical quantities, disturbance and event capturing as well as extensive range of industrial protocol interfaces are standard features in VAMP motor protection relays and managers. Extensive communication Large number of supported communication protocols including IEC 61850, IEC 60870-5-101, IEC 60870-5-103, Modbus TCP, Modbus RTU, Profibus DP, TCP/IP, SPA-bus slave, DNP 3.0 and DeviceNet.
02
Product range: VAMP 40 < 1MW Motor size 2 MW > Synchronous motors 10 MW > Synchronous motors VAMP 52 VAMP 230 VAMP 255 VAMP 257 VAMP 265M
Optional hardware
Inputs / outputs
Digital inputs (DI) max Output relays (DO) max Self-supervision controls
2 (7)
6 (8)
18 (20)
18 (20) 9
22 (24) 19
30 (32) 13
6 (8)
5 (6)
= optimal solution
= advanced solution
= supported features
03
Product highlights
VAMP 40
Unique digital multifunctionality at basic cost One type designation only; wide power supply range; 19-265 V ac/dc Small installation depth dimension 2 Digital Inputs (fixed) Connectivity to PTD input module
VAMP 52
Digital multifunction relay for asynchronous motors Large display for mimic and measurements Control keys for operational mode changes Control keys for object control Optional mA output Two optional module slots for arc sensor, Input/Output extension or various communication interfaces Connectivity to PTD input module
VAMP 230/255/257
Digital multifunction motor manager for asynchronous and synchronous motors Voltage transformer connections allow use of directional overcurrent and earth fault protection in addition to various motor protection stages Active, reactive and apparent power as well as energy measurement Input/Output capacity varies per product type Connectivity to PTD input module
VAMP 265M
Optimized for motor applications; settings proportional to motor current Connectivity to PTD input module For large synchronous and asynchronous motors Large quantity of motor protection stages with differential protection
04
The motor start-up register stores values (start current, duration, etc.) which facilitates the correct setting of the relay, even if critical motor data is unavailable from the manufacturer. An average mode recording was used to capture a lengthy voltage drop while the motor was starting. The phase voltage fluctuated from 6,226 kV down to 5,732 kV.
05
Protection
3I > 3l >> 3I > 3l >> 3l >>> 3l > 3l >> 3I >>> 3I >>>> 3Io >/ SEF 3Io >> 3Io >>> 3Io >>>> 3Io >/ SEF 3Io >> U0 > U0 >> REF T> 1U>/3U> 1U>>/3U>> 1U>>>/3U>>> 1U</3U< 1U<</3U<< 1U<<</3U<<< U2> 3 I> / I0>, L> lf2 > I2 > I2 > I2 >> IST > 3I< Three-phase non-directional overcurrent, low-set stage, definite or inverse time Three-phase non-directional overcurrent, high-set stage, definite time Three-phase non-directional overcurrent, low-set stage, definite or inverse time (secondary side) Three-phase non-directional overcurrent, high-set stage, definite time (secondary side) Three-phase non-directional overcurrent, high-set stage, definite time Three-phase directional or non dir. o/c, low-set stage, definite or inverse time Three-phase directional or non dir. o/c, high-set stage, definite or inverse time Three-phase directional or non dir. o/c, high-set stage, definite time Three-phase directional or non dir. o/c, high-set stage, definite time Non-directional earth-fault, low-set stage, sensitive, definite or inverse time Non-directional earth-fault, high-set stage, definite time Non-directional earth-fault,high-set stage, definite time Non-directional earth-fault, high-set stage, definite time Directional or non dir. earth-fault, low-set stage, sensitive, definite or inverse time Directional or non dir. earth-fault, high-set stage, definite or inverse time Zero sequence voltage, low-set stage Zero sequence voltage, high-set stage Restricted earth fault (application) Three-phase thermal overload (motors & generators) One-/Three-phase overvoltage, low-set stage One-/Three-phase overvoltage, high-set stage One-/Three-phase overvoltage, high-set stage One-/Three-phase undervoltage, low-set stage One-/Three-phase undervoltage, high-set stage One-/Three-phase undervoltage, instantaneous stage Negative sequence overvoltage (pgr stage) Electrical arc protection stage, point sensors, Optional Second harmonic Phase unbalance protection Phase unbalance protection (secondary side) Phase sequence / reversal protection Stall protection Loss of load / under current protection Latched trip Three phase biased differential stage, low-set stage, 2nd harmonic blocking Three phase differential stage, high-set stage Frequent start protection Circuit breaker failure protection Overfrequency and underfrequency protection Underfrequency protection Rate of change of frequency (ROCOF) protection Synchrocheck Short circuit fault location 8 Programmable stages Disturbance recorder
1 1 1 1 1 1
1 1 1 1 1 1
3 3 3 3 3 3
3 3 3 3 3 3
3 3 3 3 3 3
VAMP 265M
VAMP 230
VAMP 255
VAMP 257
VAMP 40
VAMP 52
06
Type of measurement
IEC Symbol
Protection function/measurement
Measurements
3dI> Primary current 3Io I2 IL U/3U Primary voltage Short-circuit fault reactance Frequency Power Energy Power factor Harmonics Voltage sags / swells Analog mA output, 1 channel Analog mA output, 4 channels U0 U2 / U1 Xfault f P Q S E+, EEq+, EqPF I U U AO AO Three-phase differential current Neutral current Current unbalance Average and maximum demand current One-/Three-phase and line voltages Zero sequence voltage Voltage unbalance (prg) Short-circuit fault reactance System frequency Active power Reactive power Apparent power Active Energy, exported / imported Reactive Energy, exported / imported Power factor 2nd to 15th and THD of phase currents 2nd to 15th and THD of measured voltages Voltage sags / swells Any measured or calculated value, freely scalable Any measured or calculated value, freely scalable, Optional
* * * * * *
* * * * * * *
1)
Control
Digital inputs (DI) Output relays (DO) Object status indication Local and remote control Interlocking and logic Number of digital inputs (max) Number of trip relays (max) Number of alarm relays Single line diagram, 8 objects Number of controllable objects Configurable 6 6 6 6 6 6 2 4 1 7 5 1 8 20 32 2 5 4 5 14 5 8 2 5
Condition monitoring
Trip circuit CT Supervision VT Supervision CB Wear 60 TCS TCS Trip Circuit Supervision Trip Circuit Supervision with DI for T5...T8 CT Supervision VT Supervision/Fuse failure supervision Breaker wear 1)
Communication
IEC 60870-5-101 IEC 60870-5-103 Modbus TCP Modbus RTU Profibus DP DNP 3.0 SPA-bus communication IEC 61850 DeviceNet Ethernet / IP Human-Machine-Communication, display Human-Machine-Communication, PC
General functions
Self Supervision Annunciating, event generating and value recording Measurement and parameter display Real time clock Year, month, day, hour, minutes, seconds, milliseconds
* = limited functionality 1) = Option
VAMP 265M
VAMP 230
VAMP 255
VAMP 257
VAMP 40
VAMP 52
07
Typical applications
VAMP 40
LED indicators External support to arc interface module
VAMP 52
Large mimic LED indicators 2 Configurable keys Control of CB DI/DO or Arc optional expansion mA option
CB or contactor
1 3 1
VAMP 40
50/51,50/51N, 50GS, 46, 49M, 48, 66, 37, 67N, 32 1 3
VAMP 52
50/51,50/51N,50BF, 50NARC,46,49M,47, 48,59,66,74TC,37, 67NT,37,27,59,86, 8 prg
VIO 12 (RTD)
VIO 12 (RTD)
38, 39
VAMP 230/255/257
Extended DI/DO for breaker status indication and control Three phase voltage inputs for directional overcurrent protection, power and energy measurements VAMP 257 for double busbar control
VAMP 265M
Combined motor and differential protection Differential stage optimized for motors
VAMP 265M
50/51,50I/51I,37,87, 46,47.48,66,49, 50N/51N,50NI/51NI, 50BF,99, 50ARC, 50NARC
3 3
VAMP 230/255/257
50/51,50/51N, 46,49 M,47, 48,66,37,67N, 37,27,59,81
VIO 12 (RTD)
38, 39
3 3 1 > 5000 kW > 6700 hp 3 50/51, 50I/51I, 37,87, 46,47.48,66,49, 50N/51N, 50NI/51NI, 50BF,99, 50ARC, 50NARC
50/51,50/51N, 50BF, 50NARC, 46, 49M, 47, 48, 59,66,74TC, 37, 67NT,37,27, 59,86, 8 prg
VAMP 265M
VAMP 52
08
VIO 12 RTD module is used for extending the measuring quantities of VAMP motor protection relays. The VIO 12 module has channels for RTD sensors, mA inputs and outputs and PTC input. The interface to the relay is either RS-232, RS-485 or glass fibre, allowing the input module to be close to the motor and limit the length of temperature sensor cables. All information measured by the VIO module is available in the protection relay for protection elements, measurements, logic, alarms and event reporting.
RS 232 communication with VAMP 40 only RS 485 communication No. of RTD channels for Pt100, Ni100, Ni120, Cu10 No. of mA inputs No. of mA outputs PTC input Auxiliary supply 24 230 Vac/dc 12 12 12 4 4 1 24 V dc 12 4 4 1 48 230 V
Comms. option
A rc option
RTD connection
RTD connection Up to 12 RTD inputs, plus one contact (speed switch etc.)
BI/O
L>
VIO 12AA
09
CB
BB CB
CB
Cable
Cable
The VAMP arc flash protection devices also provide cost efficient high-speed MV busbar protection.
BB
CB
The integrated arc flash sensors monitor for possible arc fault in combined circuit breaker and cable compartment (CB) and in cable termination (CTB) box.
CTB
10
Connection diagrams
VAMP 40 CONNECTION DIAGRAM
L1
L2
L3
X2:15 X2:16
VAMP 40
Protection functions
50 / 51
3I> 3I>> 3I>>>
Front
X1 X4
67N
I0> I0> >
50N/51N
I0>
Remote
X6:1 X6:2 X6:3 X6:4 X6:5 X6:6 X6:7 X6:8 X6:9 X6:10 X6:11 X6:12
59
U> U>> U>>>
27
U< U<< U<<<
U0>
U0> >
T1 T2 T3 T4 A1
X2:14 X2:13 X2:12 X2: 11 X2:10 X2: 9 X2: 8 X2: 7 X2: 4 X2: 6 X2: 5
50BF
CBFP
+ +
50ARC
ArcI >
50NARC
ArcI 01 > ArcI 02>
59C UC > 32
P< P<<
67NT
I0T>
5A 1A
48 Ist>
49
T>
37 3I< 66 N> 79
1A 0.2A
46
I2 >
U12
X6:13 X6:14
U0 /U L1 / U12
46R
I2 /I1 >
VA MP 255
Auto Reclose
IF
DI
X2: 1 X2: 2
VAMP 52
Protection functions
50 / 51 50N/51N 27
Front
Comm. option
Remote
X6:1 BO+ X6:2 BOX6:3 BI+ X6:4 BIX6:5 L1 + X6:6 L1 X6:7 L2+ X6:8 L2-
BI/ O
X1: 1 X1: 2 IL1 X1: 3 X1: 4 IL2 X1: 5 X1: 6 IL3 X1: 7
I0T>
50BF
59N
CBFP
50ARC
T1 T2 T3 T4 C1
X3:17 X3:16 X3:15 X3:14 X3:13 X3:12 X3: 11 X3:10 X3: 7 X3: 9 X3: 8
L>
+ +
ArcI >
50NARC
T>
68
ArcI 01 >
74TC TCS 86
X1:8
X1: 9 X1:10
I0
If2 >
59
Lockout
U0
X1: 11
U / U 1/ U12
U>
37 3I< 67N
U>> U>>>
X6:1 X6:2 X6:3 DI3 X6:4 Comm X6:5 DI4 X6:6 DI5 X6:7 Comm X6:8 Di6
T5
DI
X3:3 X3:4 X3:5 X3:6
X6:1 X6:2 Arc option X6:3 or X6:4 X6:5 DI / DO X6:6 module X6:7 X6:8
DI1 DI1+ DI2 DI2+
79 Auto Reclose
IF
Autorecloser matrix
mA out option
DI
mA
DI
11
VAMP 255
**
U12y
+ +
X3:17
~
IL1 IL2 IL3 I01 I02 U12 U12Y Uo
O p tionBlo c k
U12 Uo
X3:18 X1:1 X1:2 X1:3 X1:4 X1:5 X1:6 X1:7 X1:8 X1:9 X1:10
VAMP 257
Front
Loc a l
T1 T2 T3 T4 T5 T6 T7
X3:14 X3:1 5 X3:12 X3:13 X7:17 X7:18 X7:15 X7:16 X8:19 X8:20 X8:17 X8:18 X8:15 X8:16 X8:13 X8:14 X3:9 X3:10 X3:1 1 X2:7 X2:8 X2:5 X2:6 X2:3 X2:4 X2:1 X2:2
+ + + +
X3:1+48V X3:2DI 1 X3:3DI 2 X3:4DI3 X3:5DI 4 X3:6DI5 X3:7DI 6 X7:1DI7 X7:2DI8 X7:3DI9 X7:4DI1 0 X7:5DI1 1 X7:6DI1 2 X7:7com m
DI
T8 A1 A2
DI
DI
A3 A4 A5
DI
DI
X8:6comm X8:7DI25
X8:8DI26
Autorecloser matrix
DI
IF
X8:9comm X8:10DI27
X8:1 1DI28
DI
X8:12comm
12
L1
L2
L3
X3:17 X3:18
X1:1 X1:2 X1:3 X1:4 X1:5 X1:6 X1:1 1 X1:12 X1:13 X1:14 X1:15 X1:16 X1:7 X1:8 X1:9 X1:10
VAMP 265M
Front
Local
X4 X5
Remote
A1 T2 T1
A2 A3 A4 A5 IF
I01 I02
X2:13 X2:14 X2:15 X2:10 X2:1 1 X2:12 X2:7 X2:8 X2:5 X2:6
Arc option
X6:1 X6:2
BI/O L>
X3:1 +48VDC X3:2 DI1 X3:3 DI2 X3:4 DI3 X3:5 DI4 X3:6 DI5 X3:7 DI6
DI
13
Dimensional drawings
VAMP 40
All dimensions in mm
Panel mounting
VAMP 50
All dimensions in mm
Panel mounting
14
208
190
155 137
1 - 10 b a
a (mm) 40 60 100
Fixing bracket Standard for 200 serie s Standard for 200 serie s 2 x VYX199
15
Order codes
ORDER CODES FOR VAMP 52
Accessories, see page 19
Phase current inputs [A] 3 = 1A / 5A Earth-fault current input [A] A =1A/5A B = 0.2 A /1 A Optional I/O extension modules A = None B = Digital I/O 4 x DI, 1 x DO C = Arc Protection; 2 x Sensor, BIO
V 52 - 3
Supply Voltage [V] A = 40.. 265 Vac/dc B = 18 ... 36 Vdc mA output option A = None B = mA output DI threshold voltage
1)
Communication module 2 only available when combined with Communication module 1 options: (B) RS 485 or (L) RS232
1 = 24 VDC /110 VAC 2 = 110 VDC /220 VAC 3 = 220 VDC Optional communication module 1 A = None B = RS 485 interface with option for module 2 C = RS 232 interface D = Plastic/Plastic serial fibre interface E = Glass/Glass serial fibre interface F = Rx Plastic/Tx Glass serial fibre interface G = Rx Glass/Tx Plastic serial fibre interface H = Ethernet RJ-45, 10 Mbps interface K = IEC 61850 RJ-45, 10 Mbps interface L = RS-232 inteface with option for module 2 P = Profibus interface 2)
R = 2 x ST 100 Mbps Ethernet fibre interface with 61850 S = 2 x RJ-45 100 Mbps Ethernet interface with 61850 Optional communication module 2 A = None B = IRIG-B timesyncronisation input 1) C = RTD fiber optic interface 1) D = RJ-45 Ethernet Interface 10 Mbps
1) 1)
V 40
F = LC 100 Mbps Ethernet fibre interface 1) G = LC IEC 61850 100 Mbps Ethernet fibre interface 1)
16
V 230 - 3 V 255 - 3
7 7
Nominal current [A] 3=1A/5A Nominal earth-fault current Io1 & Io2 [A] C=1A/5A D = 0,2 A / 1 A Frequency [Hz] 7 = 50/60 Hz Supply voltage [V] A = 40.. 265 Vac/dc B = 18.. 36 Vdc C = 40.. 265 Vac/dc + ARC Protection D = 18.. 36 Vdc + ARC Protection E = 40.. 265 Vac/dc + DI19, DI20 + arc channel, optional F = 18.. 36 Vdc + DI19, DI20 + arc channel, optional Optional hardware 1 G = Rx Glass/Tx Plastic serial fibre interface A = None B = Plastic/Plastic fibre interface C = Profibus Interface D = RS485 interface E = Glass/Glass serial fibre interface F = Rx Plastic/Tx Glass serial fibre interface G = Rx Glass/Tx Plastic serial fibre interface H = RJ-45 10Mbps ethernet interface M = RJ-45 10Mbps ethernet with IEC 618500 O = LC 100 Mbps Ethernet fibre interface with IEC 61850 P = RJ-45 100 Mbps Ethernet interface with IEC 61850 R = 2 x LC 100 Mbps Ethernet fibre interface with IEC 61850 S = 2 x RJ-45 100 Mbps Ethernet interface with IEC 61850 Analog Outputs & firmware A = None, version 6 firmware B = 4 pcs, version 6 firmware E = None, standard firmware F = 4 pcs, standard firmware
17
V 257 - 3
Nominal current [A] 3=1A/5A Nominal earth-fault current Io1 & Io2 [A] C=1A/5A D = 0,2 A / 1 A Additional I/O (X8 terminal) 6 = None 7 = 8 standard inputs, 4 TCS Hybrid inputs/outputs 8 = 10 outputs 9 = 8 standard inputs and 4 outputs Supply voltage [V] A = 40.. 265Vac/dc B = 18.. 36Vdc C = 40.. 265Vac/dc + ARC Protection D = 18.. 36Vdc + ARC Protection E = 40.. 265Vac/dc + DI19, DI20 + arc channel, Optional F = 18.. 36Vdc + DI19, DI20 + arc channel, Optional Optional hardware (communication port 1) A = TTL/RS-232 B = Plastic/Plastic fibre interface (VCM fiber PP) C = N/A D = RS 485 Interface (VCM 485-4) E = Glass/Glass serial fibre interface (VCM FIBRE GG) F = Rx Plastic/Tx Glass serial fibre interface (VCM FIBRE PG) G = Rx Glass/Tx Plastic serial fibre interface (VCM FIBRE GP) I = RJ-45 connection (RS-232, VCM 232) M = ST Fibre ethernet Interface with IEC 61850 N = RTD interface (Glass Optic, VCM RTD)
Optional hardware (communication port 2) A = None C = RJ-45 connection (RS-232, VCM 232) D = RS-485 Interface (VCM 485-2) L = RJ-45 Inbuilt Ethernet M = RJ-45 Inbuilt Ethernet with IEC 61850 N = RTD interface (Glass Optic, VCM RTD)
18
V 265M
4 = 5A & 1A 5 = 5A & 5A Nominal earth-fault currents Io & Io [A] A = 5A & 5A B = 5A & 1A C = 1A & 5A D = 1A & 1A Frequency [Hz] 7 = 50/60Hz Supply voltage [V] A = 40.. 265Vac/dc B = 18.. 36Vdc C = 40.. 265Vac/dc + ARC Protection D = 18.. 36Vdc + ARC Protection E = 40.. 265Vac/dc + DI19, DI20 + arc channel, Optional F = 18.. 36Vdc + DI19, DI20 + arc channel, Optional Optional hardware A = None B = Plastic/Plastic fibre interface C = Profibus Interface D = RS485 Interface E = Glass/Glass serial fibre interface F = Rx Plastic/Tx Glass serial fibre interface G = Rx Glass/Tx Plastic serial fibe interface H = RJ-45 10Mbps ethernet interface M = RJ-45 10Mbps ethernet with IEC 61850 O = LC 100 Mbps Ethernet fibre interface, with IEC 61850 P = RJ-45 100Mbps Ethernet interface with IEC 61850 R = 2 x LC 100 Mbps Ethernet fibre interface with IEC 61850 S = 2 x RJ-45 100 Mbps Ethernet interface with IEC 61850 Software M = Standard firmware, Motor functions
19
Order code
VEA 3 CGi VPA 3 CG VSE001 VSE002 VSE003 VSE004 VCM 485+00 VCM 485+FI VCM 485+ET VCM 485+I6 VCM 485+IR VCM 485+LC VCM 485+L6 VCM 232+ET VCM FIBRE PP VCM FIBRE GG VCM PB VOM Arc+BI VOM Arc+3S VOM4DI1DO VCM 485-4 VCM 485-2 VCM fiber VCM 232 VX003-3 VX004-M3 VX028-3 VX030-3 VX032-3 VX052-3 VP40 VA1DA-6 VA1DA-20 VYX076 VYX077 VYX233 VYX 256A VIO 12 AA VIO 12 AB VIO 12 AC VIO 12 AD VAM 16D
Description
External Ethernet Interface Module Profibus Interface Module Fiber optic Interface Module RS485 Interface Module RS485 Interface Module, Ext I/O interface RS485 Interface Module, Ext I/O interface RS 485 interface RS 485 with RTD fiber optic interface RS 485 with RJ45 ethernet interface 10Mbps RS 485 with RJ45 ethernet interface 10Mbps (IEC61850) RS 485 with Irig-B time synchronization interface RS 485 with LC ethernet interface 100Mbps RS 485 with LC ethernet interface 100Mbps (IEC61850) RS 232 with RJ45 ethernet interface 10Mbps Serial fibre interface (Plastic/Plastic) Serial fibre interface (Glass/Glass) Profibus DP interface ARC option card (2S+BI) ARC option card (3S) Digital Input/Output Option Card RS-485 Interface Module, integrated for VAMP257 RS-485 Interface Module, integrated for VAMP257 Fiber Interface Module, integrated for VAMP257 RS-232 Interface Module, RJ-45, integrated for VAMP257 Programming Cable (VAMPSET, VEA 3 CG+200series) TTL/RS232 Converter Cable (for PLC, VEA3CG+200series ) Interface cable to VPA 3 CG (Profibus module) Interface cable to VEA 3 CG (Ethernet module) Rear panel programming cable USB Programming Cable Arc option Arc sensor Arc sensor Raising Frame for 200-series Raising Frame for 200-series Raising Frame for 200-series Optional seal for IP54 RTD Module, 12pcs RTD inputs, Optical Tx Communication RTD Module, 12pcs RTD inputs, RS 485 Communication RTD Module, 12pcs RTD inputs, PTC, mA inputs/outputs, RS232, RS485 and Optical Tx/Rx Communication External LED module
Note
Cable length 3 m Cable length 6 m Cable length 20 m Height 40 mm Height 60 mm Height 100 mm
20
Technical data
Auxiliary voltage
Rated voltage Uaux Type A (standard) Rated voltage Uaux Type B (option)
Power consumption
VAMP 40
19265 V ac/dc For rated voltages 24240 V ac/dc
VAMP 52
40265 V ac/dc 110/ 120/ 220/ 240 V ac 48/ 60/ 110/ 125/ 220 V dc 1836 V dc 24 V dc
VAMP 230/255
40265 V ac/dc 110/ 120/ 220/ 240 V ac 48/ 60/ 110/ 125/ 220 V dc 1836 V dc 24 V dc < 7 W (normal conditions) < 15 W (output relays activated)
VAMP 257
40265 V ac/dc 110/ 120/ 220/ 240 V ac 48/ 60/ 110/ 125/ 220 V dc 1836 V dc 24 V dc
VAMP 265M
40265 V ac/dc 110/ 120/ 220/ 240 V ac 48/ 60/ 110/ 125/ 220 V dc 1836 V dc 24 V dc
Measuring circuitry
Rated phase current In Current measuring range Thermal withstand Burden Rated phase current In Current measuring range Thermal withstand Burden Rated residual current 3Io Current measuring range Thermal withstand Burden Rated residual current 3Io Current measuring range Thermal withstand Burden Rated residual current 3Io Current measuring range Thermal withstand Burden Rated voltage Un Voltage measuring range Continuous voltage withstand Burden Rated frequency fn Frequency measuring range Terminal Block
VAMP 40
VAMP 52
5A
VAMP 230/255
(configurable for CT secondaries 1-10 A) 050xIn (0250 A) 4 x In (20 A continuously) 100 A (for 10 s) 500 A (for 1 s) < 0,2 VA
VAMP 257
VAMP 265M
In = 1A (configurable for CT secondaries 1-10 A) 050xIn (050 A) 4 x In (4 A ) (continuously) 20 A (for 10 s) 100 A (for 1 s) < 0,1 VA I01 = 5 A/ 1 A 050 A/10 A 5A/1A (optionally 1 A / 0.2 A) 050 A/10 A I02 input option C 5 A (configurable for CT secondaries 1-10 A) 050 A 4 x Ion continuously 20 x Ion (for 10 s) 100 x Ion (for 1 s) < 0,2 VA ( I02 input option C / I02 input option D ) 1 A (configurable for CT secondaries 0.1-10 A) 010 A (for VAMP 255) 05 A (for VAMP 230) I02 input option C / I02 input option D 1 A (configurable for CT secondaries 0.1-10 A) 010 A 4 x Io2n (continuously) 20 x Io2n (for 10 s) 100 x Io2n (for 1 s) < 0,1 VA I02 input option D Io1 = 0.2 A (configurable for CT secondaries 0.1-10 A) 02 A (for VAMP 255) 01 A (for VAMP 230) 4 x Io1 (continuously) 20 x Io1 (for 10 s) 100 x Io1 (for 1 s) < 0,1 VA 100 V 0 160 V 250 V < 0,5 VA 45 65 Hz 16 75 Hz (configurable for VT secondaries 50 - 120 V) 0 160 V (100 V/110 V) 250 V < 0,5 VA 45 65 Hz 16 75 Hz max wire dimension for solid or stranded wire : 4 mm2 0 160 V (100 V/110 V) 250 V < 0,5 VA 45 65 Hz 16 75 Hz (10-12 AWG) 45 65 Hz < 0,1 VA I02 input option D Io1 = 0.2 A (configurable for CT secondaries 0.1-10 A) 02 A < 0,2 VA < 0,1 VA 5 A (configurable for CT secondaries 1-10 A) I02 input option C 5 A (configurable for CT secondaries 1-10 A) 050 A 1A (configurable for CT secondaries 0,1-10 A) 05 A
I02 = 1 A/ 0.2 A
010 A/2 A 4 x Io2n (continuously) 20 x Io2n (for 10 s) 100 x Io2n (for 1 s) < 0,2 VA
025 A
21
Digital inputs
Internal operating voltage Number of inputs (internal voltage) Polarity, NO = normally open, NC = normally closed
VAMP 40
VAMP 52
VAMP 230/255
48 V dc 6 pcs NO / NC
VAMP 257
48 V dc 6 pcs
VAMP 265M
48 V dc 6 pcs
18 V ... 265 V dc
Rated voltage selectable in order code: A: 24 V dc/ 110 V ac B: 110 V dc/ 220 V ac C: 220 V dc
18 V ... 265 V dc
Number of inputs with external voltage, pcs / max. depends on ordering code Terminal block
2/7
12 / 14
12 / 14 20 / 22 24 / 26
Max wire dimension / Phoenix MVSTBW or equivalent : 2.5 mm2 (13-14 AWG)
Trip contacts
Number of contacts, pcs / max. depends on ordering code Rated voltage Continuous carry Make and carry, 0.5 s Make and carry, 3 s Breaking capacity, AC Breaking capacity, DC (L/R=40ms) Contact material Terminal Block
VAMP 40
4
VAMP 52
4
VAMP 230/255
2 (VAMP 230) 4 (VAMP 255) 250 V ac/dc 5A 30 A 15 A 2000 VA at 48 V dc: 5 A at 110 V dc: 3 A at 220 V dc: 1 A AgNi 90/10
VAMP 257
4/8/14
VAMP 265M
2
Max. wire dimension / Phoenix MVSTBW or equivalent : 2.5 mm2 / (13-14 AWG)
Alarm contacts
VAMP 40
2 change-over contacts (relays A1 and IF)
VAMP 52
2 change-over contacts (relays A1 and IF)
VAMP 230/255
VAMP 257
VAMP 265M
Number of contacts
3 change-over contacts (relays A1, A2, A3) 2 making contacts (relays A4 and A5) 1 change-over contact ( IF relay) 250 V ac/dc 15 A 5A 2 000 VA at 48 V dc: 1,3 A at 110 V dc: 0,4 A at 220 V dc: 0,2 A 2 000 VA
2 000 VA
Rated voltage Max. make current, 4s at duty cycle 10% Continuous carry Max. making current Breaking capacity, AC Breaking capacity, DC (L/R=40ms) Contact material Terminal Block AgNi 0.15 gold plated
15 A
15 A
Max. wire dimension / Phoenix MVSTBW or equivalent : 2.5 mm2 / (13-14 AWG)
22
VAMP 40
1 1 RS 232
VAMP 52
1 USB
VAMP 230/255
1 1 RS 232 2 400 187500 kb/s
VAMP 257
1 (1) RS 232
VAMP 265M
1 1 RS 232
VAMP 230/255
1 on rear panel TTL (standard) RS 232 (option) RS 485 (option) Plastic fibre connection (option) Glass fibre connection (option) 1 200 19 200 kb/s ModBus, RTU master ModBus, RTU slave SpaBus, slave IEC 60870-5-103 IEC 60870-5-101 ProfiBus DP (option or external module) DNP 3.0
VAMP 257
1 on rear panel TTL with VCM TTL (standard) RS 485 with VCM 485-4 (option) RS 232 with VCM TTL (standard) Plastic fibre connection with VCM fibre (option) Glass fibre connection with VCM fibre (option) 1 200 19 200 kb/s ModBus, RTU master ModBus, RTU slave SpaBus, slave IEC 60870-5-103 IEC 60870-5-101 ProfiBus DP (option or external module) DNP 3.0
VAMP 265M
1 on rear panel TTL (standard) RS 232 (option) RS 485 (option) Plastic fibre connection (option) Glass fibre connection (option) 1 200 19 200 kb/s ModBus, RTU master ModBus, RTU slave SpaBus, slave IEC 60870-5-103 ProfiBus DP (option or external module) DNP3.0
Number of ports
Electrical connection
1 200 19 200 kb/s ModBus, RTU master ModBus, RTU slave SpaBus, slave IEC 60870-5-103 IEC 60870-5-101 ProfiBus DP (external module) DNP 3.0
1 200 19 200 kb/s ModBus, RTU master ModBus, RTU slave SpaBus, slave IEC 60870-5-103 IEC 60870-5-101 ProfiBus DP (external module) DNP 3.0
Protocols
Ethernet connection
VAMP 40 VAMP 52
1 Ethernet RJ-45 (Ethernet 10-Base-T) 10 Mb/s VAMPSET ModBus TCP IEC 61850 DNP 3.0
VAMP 230/255
1/2 Ethernet RJ-45 (Ethernet 10-Base-T) 10 Mb/s VAMPSET ModBus TCP IEC 61850 DNP 3.0
VAMP 257
1 Ethernet RJ-45 (Ethernet 10-Base-T) 10 Mb/s VAMPSET ModBus TCP IEC 61850 DNP 3.0
VAMP 265M
1/2 Ethernet RJ-45 (10-Base-T, option, external module) 10 Mb/s VAMPSET ModBus TCP IEC 61850 DNP 3.0
nill
Protocols
Analogue outputs
VAMP 40 VAMP 52 - Option
1 120 mA, step 1 mA
VAMP 257
VAMP 265M
23
VAMP 40
2
VAMP 52
2
VAMP 230/255
2 VA 1 DA-6, VA1DA-20, VA1-EH5 12 V dc
VAMP 257
2
VAMP 265M
2
1 1 +48 V dc
1 1 +48 V dc
1 1 +48 V dc
1 1 +48 V dc
1 1 +48 V dc
Casing
Degree of protection (IEC 60529) Dimensions (W x H x D) Material Weight Color code
VAMP 40
IP20 (IP54 with sealing) 280 x 195 x 55 mm 2.0 kg
VAMP 52
IP54 130 x 170 x 210 mm 2.0 kg
VAMP 230/255
IP20 208 x 155 x 225 mm 1 mm steel plate 4.2 kg
VAMP 257
IP20 208 x 155 x 225 mm 4.2 kg
VAMP 265M
IP20 208 x 155 x 225 mm 4.2 kg
Package
Dimensions (W x H x D) Weight (Relay, Package and Manual)
VAMP 40
315 x 260 x 105 mm 3.0 kg
VAMP 52
320 x 215 x 175 mm 3.0 kg
VAMP 230/255
215 x 160 x 275 mm 5.2 kg
VAMP 257
215 x 160 x 275 mm 5.2 kg
VAMP 265M
215 x 160 x 275 mm 5.2 kg
Test voltages
Insulation test voltage (IEC 60255-5) Surge voltage (IEC 60255-5)
VAMP 40
2 kV, 50 Hz, 1 min 5 kV, 1.2/50 s, 0.5 J (Class III)
VAMP 52
2 kV, 50 Hz, 1 min 5 kV, 1.2/50 s, 0.5 J (Class III)
VAMP 230/255
2 kV, 50 Hz, 1 min (Class III) 5 kV, 1.2/50 s, 0.5 J (Class III)
VAMP 257
2 kV, 50 Hz, 1 min (Class III) 5 kV, 1.2/50 s, 0.5 J (Class III)
VAMP 265M
2 kV, 50 Hz, 1 min (Class III) 5 kV, 1.2/50 s, 0.5 J (Class III)
Enviromental conditions
Operating temperature Transport and storage temperature Relative humidity
VAMP 40
-40C to +65C
VAMP 52
-40C to +65C
VAMP 230/255
-40C to +65C 40 to +70 C < 75 % (1 year, average value)
VAMP 257
-10C to +65C
VAMP 265M
-10C to +65C
24
03-2012