Beruflich Dokumente
Kultur Dokumente
Introduction
Application Guide
It is the intent of this section to give some basic application guidelines for the use of supply and return grilles and registers in a simple non-technical manner. the information presented here is based on Prices laboratory results as well as commonly accepted industry practices supported by AsHrAE (American society of Heating, refrigeration and Air Conditioning Engineers). these application guidelines are designed to enhance your ability to use the performance data in this catalog to select an air outlet that will create an air pattern in the occupied space conducive to the comfort of the occupant. Figure 1. Model 510 single deflection supply
Double Deflection Supply A grille or register consisting of two sets of adjustable blades oriented perpendicular to each other to allow control of the air pattern in both horizontal and vertical planes. While both sets of blades have an affect on the air pattern, the front or outward most set has the most influence. the front blades should be horizontal if control of rise and drop is primary (i.e. free space or high sidewall) or vertical if spread and throw are the largest concerns. double deflection outlets are the most flexible type of grille or register. (see Figure 2) Example Model 520 or 22. Eggcrate Return A grille or register with a cubical grid core to be used for return or exhaust where maximum free area is desired and see through is not a concern. typically used in ceiling applications where see-through sight lines are minimized to directly below the grille. (see Figure 3) Example Model 80 series.
Perforated Return this grille utilizes a symmetrically perforated sheetmetal core for free areas of approximately 50%. It is typically used in ceiling applications where see through and blending with the mounting surface are of prime concerns. (see Figure 4) Example Model 10 series.
Louvered Returns these grilles and registers utilize a core of parallel fixed blades set at a deflection, usually 45 degrees from horizontal, to provide a return or exhaust unit with minimum see through. the most common application is sidewall with blade deflection upward in high applications and down in lower applications. this type of outlet usually has a slightly higher sound and pressure drop than either the eggcrate or perforated. (see Figure 5). Example Model 530 or 630.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
D-9
Single Deflection Supply A grille or register with a single set of adjustable blades which controls the air pattern in only one direction depending on blade orientation. Horizontal blades control rise and drop of the airstream. For example, to prevent unwanted drop in a free space (no ceiling) application or blow warm air down in a high sidewall application. Vertically oriented blades control the spread of the air pattern and would be used where throw, not drop, is a prime concern. these would be the most economical type of outlet. (see Figure 1) Example Model 510 or 21.
D-10
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
no Ceiling
no Ceiling
no Ceiling
4. Small circle in white area of each chart shows comparative performances of one size of grille at 300 cfm and 600 fpm outlet velocity. 5. Deflection settings and resulting patterns are shown in Product Catalog. 6. Shaded area to right of each chart indicates noise level above 30 NC.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
D-11
30
30
4
4
4
33
Example 3:
7 (24 + 3*)
5
5
5
9 (27 + 2**)
8
30
* Equal sound sources ** resulting adder for 3 dB difference between sound sources (ref. Figure 7)
Figure 7
D-1
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Application: Mid to high capacity return with core free area of approximately 50%. Perforated core blends unobtrusively with most interior design conditions. Ideally suited for ceiling mounted return applications. Construction: Available in steel or aluminum core con struction. (Aluminum core recommended for high humidity applications.) Extruded aluminum borders for clean, crisp detailing. Core 3/16" (5) holes on 1/4" (6) centers staggered 60. Mounting frames available to accent grille border and protect wall surface during grille removal. For Firerated applications please see d40. Mounting / Finish Options Border Style surface sidewall Mount 11/4" (32) Flat (standard) tBar LayIn 1" (25) tee Optional Mounting Frame For F Border (SW) Fastening Countersunk screwholes c/w ovalhead screws no screwholes
Module Size Nom. Size = Mod. Size - 2" (51) Nom. - 13/16" (21) 11/8" (28)
1" (25)
Perforated Face Face Opening = D - 11/2" (38) Mod. Size - 5/16" (8)
11/4" (32)
1/4" (6)
F (SW) F (LI) D A
11/8" (28)
Perforated Face Face Opening = D - 11/2" (38) Nom. + 111/16" (43) Optional D Mounting Frame
Finish White Powder Coat B12 For optional and special finishes see color matrix. Available Sizes Minimum 6" x 4" (152 x 102) Maximum* 48" x 24" (1219 x 610)
11/4" (32)
1] 2] 3] 4] 5] 6] 7]
Product Information Index Performance data ...............................d41 Available Borders / Frames ...... d82 d84 Available Fastenings................. d82 d84 Accessory dampers .............. d107 d109 suggested specification ................ d172
D-39
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Performance Data
Core Area Sq. Ft. 0.15 0.18 0.22 0.26 0.30 0.34 0.39 0.46 0.52 0.60 0.69 0.81 0.90 1.07 1.18 1.34 1.6 1.8 2.08 2.45 2.78 3.11 3.61 4.29 4.65 5.58 6.25 Core Velocity Velocity Pressure Negative SP CFM NC CFM NC CFM NC CFM NC CFM NC CFM NC CFM NC CFM NC CFM NC CFM NC CFM NC CFM NC CFM NC CFM NC CFM NC CFM NC CFM NC CFM NC CFM NC CFM NC CFM NC CFM NC CFM NC CFM NC CFM NC CFM NC CFM NC 200 0.002 0.019 30 36 44 52 60 68 78 92 104 120 138 162 180 214 236 268 320 360 416 490 556 622 722 858 930 1116 1250 300 0.006 0.043 45 54 66 78 90 102 117 138 156 180 207 243 270 321 354 402 480 540 624 735 834 933 1083 1287 1395 1674 1875 400 0.010 0.076 60 72 88 104 120 136 156 184 208 240 276 324 360 428 472 536 640 720 832 980 1112 1244 1444 1716 1860 2232 2500 NC 20 500 600 0.016 0.022 0.118 0.171 75 90 20 25 90 108 20 25 110 132 20 25 130 156 20 25 150 180 20 25 170 204 20 25 195 234 20 25 230 276 20 25 260 312 20 25 300 360 20 25 345 414 20 25 405 486 20 25 450 540 20 25 535 642 20 25 590 708 20 25 670 804 20 25 800 960 20 25 900 1080 20 25 1040 1248 20 25 1225 1470 20 25 1390 1668 20 25 1555 1866 20 25 1805 2166 20 25 2145 2574 20 25 2325 2790 20 25 2790 3348 20 25 3125 3750 20 25 NC 20 NC 30 700 800 0.031 0.040 0.232 0.303 105 120 29 33 126 144 29 33 154 176 29 33 182 208 29 33 210 240 29 33 238 272 29 33 273 312 29 33 322 368 29 33 364 416 29 33 420 480 29 33 483 552 29 33 567 648 29 33 630 720 29 33 749 856 29 33 826 944 29 33 938 1072 29 33 1120 1280 29 33 1260 1440 29 33 1456 1664 29 33 1715 1960 29 33 1946 2224 29 33 2177 2488 29 33 2527 2888 29 33 3003 3432 29 33 3255 3720 29 33 3906 4468 29 33 4375 5000 29 33 NC 30 900 0.050 0.384 135 36 162 36 198 36 234 36 270 36 306 36 351 36 414 36 468 36 540 36 621 36 729 36 810 36 963 36 1062 36 1206 36 1440 36 1620 36 1872 36 2205 36 2502 36 2799 36 3249 36 3861 36 4185 36 5022 36 5625 36 1000 0.062 0.474 150 39 180 39 220 39 260 39 300 39 340 39 390 39 460 39 520 39 600 39 690 39 810 39 900 39 1070 39 1180 39 1340 39 1600 39 1800 39 2080 39 2450 39 2780 39 3110 39 3610 39 4290 39 4650 39 5580 39 6250 39
Nominal Size 6 x 5 7 x 4 6 x 6 7 x 5 8 x 4 7 x 6 10 x 4 6 x 6 10 x 5 12 x 4 14 x 4 10 x 6 12 x 5 16 x 4 8 x 8 12 x 6 14 x 5 18 x 4 20 x 4 14 x 6 16 x 5 10 x 8 24 x 4 16 x 6 18 x 5 28 x 4 18 x 6 20 x 5 12 x 8 30 x 4 20 x 6 24 x 5 14 x 8 36 x 4 22 x 6 28 x 5 16 x 8 40 x 4 26 x 6 30 x 5 18 x 8 48 x 4 30 x 6 36 x 5 18 x 10 34 x 6 20 x 10 24 x 8 16 x 12 60 x 4 36 x 6 48 x 5 18 x 12 72 x 4 24 x 10 30 x 8 22 x 12 60 x 5 36 x 8 48 x 6 30 x 10 72 x 5 40 x 8 60 x 6 36 x 10 72 x 6 32 x 12 48 x 8 26 x 14 36 x 12 26 x 16 30 x 14 24 x 18 60 x 8 40 x 12 48 x 10 36 x 14 72 x 8 48 x 12 60 x 10 36 x 16 48 x 14 32 x 20 36 x 18 28 x 24 72 x 10 36 x 20 48 x 16 30 x 24 72 x 12 48 x 18 60 x 14 36 x 24 72 x 14 48 x 20 60 x 16 30 x 30
10 x 10 12 x 10 14 x 10 16 x 10 12 x 12 14 x 12 14 x 14 16 x 14 18 x 14 16 x 16 24 x 12 20 x 14 30 x 12 24 x 14 24 x 16 20 x 18 22 x 20 30 x 16 26 x 18 30 x 18 24 x 24
18 x 16 20 x 16 18 x 18 24 x 20
Performance Notes 1. Tested in accordance with ASHRAE Standard 70-2006 Method of Testing for Rating the Performance of Air Outlets and Inlets. 2. All pressures are in inches of water.
Copyright E.H. Price Limited 2007.
3. The NC values are based on a room absorption of 10 dB, re 10-12 watts. 4. Blanks () indicate an NC level below 15.
5. Air flow is in cubic feet per minute, cfm. 6. Neg. SP is negative static pressure.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
D-41
std. = standard Border / Fastening supplied with grille / register * Concealed Fastening not available for tB and CH Borders. ** damper not available for CH border. Outlet Mounted Accessory Opposed Blade Damper D steel Construction DAL Aluminum Construction
D-8
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Dimensioned Details
F Border FD Border / Frame (for 500/600) C Border CK Border / Frame TB Border
1 1/4" (32) curved border for surface mount. K mounting frame is curved to complement C border.
For T-bar lay-in application. Steel panel is provided when ceiling module is more than 2" (51) over duct size. Note that concealed fastening is not available. 60 / 70 Series uses .730" (18) face.
ED Border / Frame
GRILLES AND REGISTERS
13
1" (25) narrow low profile border with matching curved mounting frame to satisfy architectural / space conditions.
/16" (21) border for exposed duct. Frame hems the raw edge of the duct providing a neat, clean grille mount. Note the reduced core area of this border. See Performance Notes for correction factors to catalog data.
TBP Panel
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
D-83
Dimensioned Details
CH Border A screw Fastening C Concealed Fastening
Channel border designed for non-ducted applications in t-bar ceilings. It provides structural strength to the grille and is hidden by the ceiling grid.
Counter-sunk screwholes in border type. Factory painted oval head screws supplied.
Permits surface mounting with concealed screw. the bracket attached to the back of the grille screws to a loose bracket which hooks into a hem in the duct.
D-84
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Perforated Face
10 Return Grille Furnish and install Price model (10 steel/ 10A aluminum) return grilles of the sizes and mounting types indicated on the plans and outlet schedule. grilles shall consist of a perforated core with 3/16" (5) holes on 1/4" (6) centers staggered 60 degrees and an extruded aluminum border. the grille shall be finished in (B12 White Powder Coat / B15 Aluminum Powder Coat).
D-17
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.