Beruflich Dokumente
Kultur Dokumente
Description
Avago Technologies MGA-22003 linear power amplifier is designed for mobile and fixed wireless data applications in the 2.3 to 2.7 GHz frequency range. The PA is optimized for IEEE 802.16 WiMAX/WiBro modulation but can be used for any high linearity applications. The PA exhibits flat gain and good match while providing linear power efficiency to meet stringent mask conditions. It utilizes Avago Technologies proprietary GaAs Enhancement-mode pHEMT technology for superior performance across voltage and temperature levels. The MGA-22003 is packaged in a 3x3x1 mm package for space-constrained applications.
Features
Advanced GaAs E-pHEMT 50 all RF ports 9dB gain step in low power mode with Idsq reduction Integrated CMOS compatible pins for shutdown and low power mode 3 to 5V supply ESD protection all ports above 800V HBM Small size: 3 x 3 x 1 mm Stable under all loads or conditions -40C to +85C operation
Applications
Portable WiMAX/WiBro and WiFi applications WiMAX/WiBro and WiFi Access points
At 2.5GHz
Gain of 35dB PAE of 18% at SEM compliant Pout=25dBm Meets 802.16 masks at 25 dBm Pout, 16QAM WiMAX with 3.3V and 512mA
GND 14 VCC2 13 GND 12
16QAM WiMAX EVM < -32dB (2.5%) at 25dBm Low power Idd, 80mA at Pout=0dBm, 9dB Gain Step
GND 2
OMN ISMN
RFOUT 11 GND 10
GND
14
BIAS NETWORK
VCC2
13 12
GND
1 2 3 4 5 6 7 8
17 GND
11 10 9
NC
BSW 6
PMOD 7
N/C 8
Top View
22003 = Product Code KA = Korea ASE YY = Year code indicates the year of manufacture WW = Workweek code indicates the workweek of manufacture XXXXX = Last 5 digit of assembly lot number
This preliminary data is provided to assist you in the evaluation of product(s) currently under development. Until Avago Technologies releases this product for general sales, Avago Technologies reserves the right to alter prices, specifications, features, capabilities, functions, release dates, and remove availability of the product(s) at anytime.
BSPLY
BSW
NC
N/C 9
Specifications Pin
VCC1 VCC2 BSPLY BCTRL BSW PAMODE RFIN
Min.
Typical
3.3 3.3 2.8 1.8 1.8
Max.
5.5 4.2 4.2 4.2 4.2 15 MSL3 150 150 800 50
Unit
V V V V V dBm C C V V
Comments
Specifications Pin
VCC1 VCC2 BSPLY BCTRL BSW PAMODE RFOUT 2.3 23.4 +85
Min.
3 3 2.75 1.65 1.65
Typical
3.3 3.3 13 2.8 .7 1.8 7 1.8 17
Max.
5 3.5 2.85 2.2 25 2.2 25 25 2.7
Unit
V V mA V uA V uA V uA dBm GHz C/W C
Comments
Min.
Typical
-10 1
Max.
Unit
dB dB
Comments
Over any 10MHz 3V to 5V Vcc=3.3V Vcc=3.6V IBW=100kHz IBW=1MHz
dB dB dBm/100kHz dBm/MHz
dBm mA
EVM (dB)
Figure 1. EVM Frequency Sweep at 25C and Pout=25dBm over Vcc EVM Frequency Sweep (Tambient=-30C to +85C) Vcc=3.3V and Pout=25dBm
Figure 2. EVM Frequency Sweep at 25C and Pout=26dBm over Vcc EVM Power Sweep (Freq=2.3 to 2.7GHz) Tambient=25C and Vcc=3.3V 2.3GHz 2.4GHz 2.5GHz 2.6GHz 2.7GHz
-20 -22 -24 -26 -28 -30 -32 -34 -36 -38 -40 2300
-20.00 -22.00 -24.00 -26.00 -28.00 -30.00 -32.00 -34.00 -36.00 -38.00 -40.00 -42.00 -44.00 20.0
EVM (dB)
EVM (dB)
21.0
22.0
25.0
26.0
Figure 3. EVM Frequency Sweep at Vcc=3.3V and Pout=25dBm over Tambient EVM Power Sweep (Freq=2.3 to 2.7GHz) Tambient=-30C and Vcc=3.3V 2.3GHz 2.4GHz 2.5GHz 2.6GHz 2.7GHz
Figure 4. EVM Power Sweep at Vcc=3.3V and 25C over Frequency EVM Power Sweep (Freq=2.3 to 2.7GHz) Tambient=+85C and Vcc=3.3V 2.3GHz 2.4GHz 2.5GHz 2.6GHz 2.7GHz
-20.00 -22.00 -24.00 -26.00 -28.00 -30.00 -32.00 -34.00 -36.00 -38.00 -40.00 -42.00 -44.00 20.0
21.0
22.0
25.0
26.0
-20.00 -22.00 -24.00 -26.00 -28.00 -30.00 -32.00 -34.00 -36.00 -38.00 -40.00 -42.00 -44.00 20.0
EVM (dB)
EVM (dB)
21.0
22.0
25.0
26.0
Gain Frequency Sweep (Vcc=3.0 to 5.0V) Tambient=25C and Pout=25dBm 3V6 4V2 5V0
Gain Frequency Sweep (Tambient=-30C to +85C) Vcc=3.3V and Pout=25dBm -30C 25C +85C
2400
2600
2700
2400
2600
2700
Figure 7. Gain Frequency Sweep at 25C and Pout=25dBm over Vcc Gain Power Sweep (Freq=2.3 to 2.7GHz) Tambient=25C and Vcc=3.3V 2.3GHz 2.4GHz 2.5GHz 2.6GHz 2.7GHz
Figure 8. Gain Frequency Sweep at Vcc=3.3V and Pout=25dBm over Tambient Gain Power Sweep (Freq=2.3 to 2.7GHz) Tambient=-30C and Vcc=3.3V 2.3GHz 2.4GHz 2.5GHz 2.6GHz 2.7GHz
40.00 39.00 38.00 Gain (dB) 37.00 36.00 35.00 34.00 33.00 32.00 20.0
40.00 39.00 38.00 Gain (dB) 37.00 36.00 35.00 34.00 33.00 32.00 20.0
21.0
22.0
25.0
26.0
21.0
22.0
25.0
26.0
Figure 9. Gain Power Sweep at Vcc=3.3V and 25C over Pout Gain Power Sweep (Freq=2.3 to 2.7GHz) Tambient=+85C and Vcc=3.3V 2.3GHz 2.4GHz 2.5GHz 2.6GHz 2.7GHz
Figure 10. Gain Power Sweep at Vcc=3.3V and -30C over Pout Total Current Frequency Sweep (Vcc=3.0 to 5.0V) Tambient=25C and Pout=25dBm 3V0 3V3 3V6 4V2 5V0
40.00 39.00 38.00 Gain (dB) 37.00 36.00 35.00 34.00 33.00 32.00 20.0
21.0
22.0
25.0
26.0
0.6 0.58 0.56 0.54 0.52 0.5 0.48 0.46 0.44 0.42 0.4 2300
Itotal (A)
2400
2600
2700
Figure 11. Gain Power Sweep at Vcc=3.3V and -+85C over Pout
Figure 12. Total Current Frequency Sweep at 25C and Pout=25dBm over Vcc
0.60 0.58 0.56 0.54 0.52 0.50 0.48 0.46 0.44 0.42 0.40 2300
Total Current Frequency Sweep (Tambient=-30C to +85C) Vcc=3.3V and Pout=25dBm -30C 25C +85C Itotal (A)
0.62 0.58 0.54 0.50 0.46 0.42 0.38 0.34 0.30 20.0
Total Current Power Sweep (Freq=2.3 to 2.7GHz) Tambient=25C and Vcc=3.3V 2.3GHz 2.4GHz 2.5GHz 2.6GHz 2.7GHz
Itotal (A)
2400
2600
2700
21.0
22.0
25.0
26.0
Figure 13. Total Current Frequency Sweep at 3.3V and Pout=25dBm over Tambient Total Current Power Sweep (Freq=2.3 to 2.7GHz) Tambient=-30C and Vcc=3.3V 2.3GHz 2.4GHz 2.5GHz 2.6GHz 2.7GHz
Figure 14. Total Current Power Sweep at 3.3V and 25C over Frequency Total Current Power Sweep (Freq=2.3 to 2.7GHz) Tambient=+85C and Vcc=3.3V 2.3GHz 2.4GHz 2.5GHz 2.6GHz 2.7GHz
0.62 0.58 0.54 Itotal (A) 0.50 0.46 0.42 0.38 0.34 0.30 20.0
0.620 0.580 0.540 Itotal (A) 0.500 0.460 0.420 0.380 0.340 0.300 20.0
21.0
22.0
25.0
26.0
21.0
22.0
25.0
26.0
Figure 15. Total Current Power Sweep at 3.3V and -30C over Frequency
Figure 16. Total Current Power Sweep at 3.3V and +85C over Frequency
WiMAX Spectrum Emission Mask, 802.16e (16QAM 3/4) Pout=25dBm, Vcc=3.3V and Tambient=25C Spec 2.5GHz 2.6GHz 2.7GHz
WiMAX Spectrum Emission Mask, 802.16e (16QAM 3/4) Pout=25dBm, Vcc=3.6V and Tambient=25C Spec 2.5GHz 2.6GHz 2.7GHz
-15.00
15.00
25.00
-60 -25.00
-15.00
15.00
25.00
Figure 17. SEM Frequency Sweep at Vcc=3.3V and 25C (2dB Post-PA loss assumed) WiMAX Spectrum Emission Mask, 802.16e (16QAM 3/4) Pout=25dBm, Vcc=4.2V and Tambient=25C Spec 2.5GHz 2.6GHz 2.7GHz
Figure 18. SEM Frequency Sweep at Vcc=3.6V and 25C (2dB Post-PA loss assumed) WiMAX Spectrum Emission Mask, 802.16e (16QAM 3/4) Pout=25dBm, Freq=2.5GHz and Tambient=25C Spec 3V0 3V3 3V6 4V2 5V0
-15.00
15.00
-60 -25.00
-15.00
15.00
25.00
Figure 19. SEM Frequency Sweep at Vcc=4.2V and 25C (2dB Post-PA loss assumed) WiMAX Spectrum Emission Mask, 802.16e (16QAM 3/4) Pout=25dBm, Freq=2.6GHz and Tambient=25C Spec 3V0 3V3 3V6 4V2 5V0
Figure 20.SEM at Vcc=3.3V, 25C and 2.5GHz over Vcc (2dB Post-PA loss assumed) WiMAX Spectrum Emission Mask, 802.16e (16QAM 3/4) Pout=25dBm, Freq=2.7GHz and Tambient=25C Spec 3V0 3V3 3V6 4V2 5V0
30 20 10 Pout (dBm/MHz) 25.00 0 -10 -20 -30 -40 -50 -60 -25.00
-15.00
15.00
-15.00
15.00
25.00
Figure 21. SEM at Vcc=3.3V, 25C and 2.6GHz over Vcc (2dB Post-PA loss assumed)
Figure 22. SEM at Vcc=3.3V, 25C and 2.7GHz over Vcc (2dB Post-PA loss assumed)
WiMAX Spectrum Emission Mask, 802.16e (16QAM 3/4) Vcc=3.3V, Freq=2.5GHz and Tambient=-30C Spec 25dBm 24dBm 23dBm 22dBm 21dBm
WiMAX Spectrum Emission Mask, 802.16e (16QAM 3/4) Vcc=3.3V, Freq=2.6GHz and Tambient=-30C Spec 25dBm 24dBm 23dBm 22dBm 21dBm
-15.00
15.00
25.00
-15.00
15.00
25.00
Figure 23. SEM at Vcc=3.3V, -30C and 2.5GHz over Vcc (2dB Post-PA loss assumed) WiMAX Spectrum Emission Mask, 802.16e (16QAM 3/4) Vcc=3.3V, Freq=2.7GHz and Tambient=-30C Spec 25dBm 24dBm 23dBm 22dBm 21dBm
Figure 24. SEM at Vcc=3.3V, -30C and 2.6GHz over Vcc (2dB Post-PA loss assumed) WiMAX Spectrum Emission Mask, 802.16e (16QAM 3/4) Vcc=3.3V, Freq=2.5GHz and Tambient=25C Spec 25dBm 24dBm 23dBm 22dBm 21dBm
30 20 10 Pout (dBm/MHz) 25.00 0 -10 -20 -30 -40 -50 -60 -25.00
-15.00
15.00
-15.00
15.00
25.00
Figure 25. SEM at Vcc=3.3V, -30C and 2.7GHz over Vcc (2dB Post-PA loss assumed) WiMAX Spectrum Emission Mask, 802.16e (16QAM 3/4) Vcc=3.3V, Freq=2.6GHz and Tambient=25C Spec 25dBm 24dBm 23dBm 22dBm 21dBm
Figure 26.SEM at Vcc=3.3V, 25C and 2.5GHz over Vcc (2dB Post-PA loss assumed) WiMAX Spectrum Emission Mask, 802.16e (16QAM 3/4) Vcc=3.3V, Freq=2.7GHz and Tambient=25C Spec 25dBm 24dBm 23dBm 22dBm 21dBm
-15.00
15.00
-60 -25.00
-15.00
15.00
25.00
Figure 27. SEM at Vcc=3.3V, 25C and 2.6GHz over Vcc (2dB Post-PA loss assumed)
Figure 28. SEM at Vcc=3.3V, 25C and 2.7GHz over Vcc (2dB Post-PA loss assumed)
WiMAX Spectrum Emission Mask, 802.16e (16QAM 3/4) Vcc=3.3V, Freq=2.5GHz and Tambient=85C Spec 25dBm 24dBm 23dBm 22dBm 21dBm
WiMAX Spectrum Emission Mask, 802.16e (16QAM 3/4) Vcc=3.3V, Freq=2.6GHz and Tambient=85C Spec 25dBm 24dBm 23dBm 22dBm 21dBm
-15.00
15.00
25.00
-15.00
15.00
25.00
Figure 29. SEM at Vcc=3.3V, +85C and 2.5GHz over Vcc (2dB Post-PA loss assumed) WiMAX Spectrum Emission Mask, 802.16e (16QAM 3/4) Vcc=3.3V, Freq=2.7GHz and Tambient=85C Spec 25dBm 24dBm 23dBm 22dBm 21dBm
Figure 30. SEM at Vcc=3.3V, +85C and 2.6GHz over Vcc (2dB Post-PA loss assumed)
-15.00
15.00
25.00
Figure 31. SEM at Vcc=3.3V, +85C and 2.7GHz over Vcc (2dB Post-PA loss assumed)
Function
VCC2 B_SPLY VCC1 NC PAMOD NC NC B_CTRL NC NC
Recommended turn on sequence Apply VCC1 and VCC2 3.3V Apply BSPLY 3.3V Apply BCTRL 2.8V Apply BSW 1.8V For HPM Apply PAMOD 1.8V for LPM Apply PAMOD 0V Apply RF In, not to exceed 15dBm
HPM
3.3V 1.8V 3.3V 2.8V 1.8V
LPM
3.3V 0V 3.3V 2.8V 1.8V Supply Voltage Low Power Mode Bias Voltage Bias Control PA Enable
Notes: VCC1, VCC2 and B_SPLY can be tied together to reduce supply voltages, but B_CTRL needs to be a regulated voltage which is optimized for 2.8V.
10
RF In
BCTRL
4 BCTRL 4 BCTRL 100pF 100pF 100pF 6 BSW 6 BSW 100pF 7 PAMOD 7 NC BCTRL 5 BSPLY 5 BSPLY R1 R2 BSPLY
0.1uF
BSPLY BSW
Using 3.3V or 5V Supply and connecting Vcc1, Vcc2, BSLPY and BCTRL
Vbat
Vcc1
Vcc2
3.3V Example :
VBCTRL = 2.85V = R1 R2 R2 R1 + R2 10M R1 + 10M *VBATT *3.3V
Given :
VBCTRL = 2.85V VBAT R2 R1 = 3.3V = 10M =?
5.0V Example :
VBCTRL = 2.85V = R1 R2 R2 R1 + R2 10M R1 + 10M *VBATT *5.0V
Given :
VBCTRL = 2.85V VBAT R2 R1 = 5.0V = 10M =?
= 1.58M = 10M
= 7.54M = 10M
11
Low Current Operation: 400mA at 25dBm Pout with BCTRL = 1.8V and VCC = 3.3V
Example 1 is very typical of mobile device application where ~400mA of current consumption is required. With the above settings at full power of 25dBm, IDD drops from 500mA to 418mA with some trade-off in EVM but still meeting SEM.
0.480 0.460 0.440 0.420 0.400 0.380 0.360 0.340 0.320 1V4 1V6 0.300 2300.00 2400.00
Idd Frequency Sweep (BCTRL = 1.4 to 2.5V) Tambient = 25C and Pout = 25dBm and Vbat = 3.3
Idd [mA]
1V8
2V0
2V2
2V5 2700.00
Table 5. Low Current Biasing Optimal settings for BCTRL (2.3G - 2.7G)
VCC = BSPLY = 3.3V Pout
25dBm 24dBm 23dBm Idsq
BCTRL
1.8V 1.7V 1.7V x
Idd
418mA 367mA 330mA 94mA
Pout
25dBm 24dBm 23dBm Idsq
BCTRL
2.8V 2.8V 2.8V x
Idd
501mA 464mA 435mA 240mA
EVM
-32dB -33dB -35dB x
-20.00 -22.00 -24.00 EVM [dB] -26.00 -28.00 -30.00 -32.00 -34.00 -36.00 2300
EVM Frequency Sweep (Vcc = 3.0 to 5.0V) Tambient = 25C and Pout = 26dBm 3V3 3V6 4V2 5V0
2400
2600
2700
12
Land Pattern
3.000.10 VCC1 VCC2 GND GND GND 3.000.10 VCC1 VCC2 13 0.550.10 12 17 GND 11 10 9 5 0.550.10 BSPLY 0.300.10 6 BSW 7 PAMOD 8 NC 0.650.10 0.400.10 GND RFOUT GND NC 0.100.10 GND 14
1.500.10 16 RFIN 3.000.10 1.500.10 GND GND BCTRL 1 2 3 4 5 BSPLY 6 BSW 7 PAMOD 8 NC 17 GND 15 14 13 0.600.10 12 11 10 9 GND RFOUT GND NC 0.200.10 RFIN 3.000.10 GND GND BCTRL 1 2 3 4 16
1.600.10 15
3.000.10 VCC1 1.500.10 16 RFIN 3.000.10 1.500.10 GND GND BCTRL 1 2 3 4 5 BSPLY 0.150.10 6 BSW 7 PAMOD 8 NC 0.300.10 0.300.10 17 GND 15 14 13 0.600.10
Notes: 1. All units are in millimeters 2. package is symmetrical
VCC2
GND
GND
12 11 10 9
13
Ordering Information
Part Number
MGA-22003-BLK MGA-22003-TR1 MGA-22003-TR2
12mm
330 +2.0 2.0 1.5min. 13.0 +0.5 0.2 20.2min. 100 +3.0 0.0 12.4 +3.0 0.0 16.4 +2.0 2.0
Container
Antistatic Bag 7" Reel 13" Reel
A B C D N
W1 W2
B N C A
0.300.05
.50
+0 . 0.0 10 0
2.000.05
4.000.10
1.700.10
3.400.10
14
3.400.10
3.0
+0 0.2 .50 0
CRITICAL ZONE TL TO TP tL
Profile Feature
Average ramp-up rate (TL to TP) Preheat Temperature Min (Tsmin) Temperature Max (Tsmax) Time (mon to max) (ts) Tsmax to TL Ramp-up Rate Time maintained above: Temperature (TL) Time (TL) Peak temperature (Tp) Time within 5C of actual Peak Temperature (tp) Ramp-down Rate Time 25C to Peak Temperature
Sn-Pb Solder
3C/sec max 100C 150C 60-120 sec
Pb-Free Solder
3C/sec max 100C 150C 60-180 sec 3C/sec max
183C 60-150 sec 240 +0/-5C 10-30 sec 6C/sec max 6 min max
217C 60-150 sec 260 +0/-5C 10-30 sec 6C/sec max 8 min max
This preliminary data is provided to assist you in the evaluation of product(s) currently under development. Until Avago Technologies releases this product for general sales, Avago Technologies reserves the right to alter prices, specifications, features, capabilities, functions, release dates, and remove availability of the product(s) at anytime.
For product information and a complete list of distributors, please go to our web site:
www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright 2005-2012 Avago Technologies. All rights reserved. AV02-1959EN - April 5, 2012