Sie sind auf Seite 1von 7

IS 1363 (Part3) 1so 4034~: 1996

( Reaffirmed 1998 )

: 1992

Indian Standard
HEXAGON HEAD BOLTS, SCREWS AND NUTS OF PRODUCT GRADE C
PART 3 HEXAGON
NUTS ( SIZE RANGE M5 TO M64 )

( Third Revision )
FirstReprint DECEMBER 1993

UDC

62188231

@ BIS 1992

BUREAU
MANAK

OF

INDIAN

STANDARDS
ZAFAR MARG

BHAVAN,

9 BAHADUR SHAH NEW DELHI 110002

October 1992

Price Group 2

Bolts, Nuts and Fastener Accessories

Sectional

Committee,

LM 14

NATIONAL

FOREWORD

This Indian Standard ( Part 3 ) which is identical with IS0 4034: 1986 Hexagon nuts Product grade C issued by the International Organization for Standardization ( IS0 ) was adopted by the Bureau of Indian Standards on the recommendation of the Bolts, Nuts and Fastener Accessories Sectional Committee ( LM 14 ) and approval of the Light Mecllanical Engineering Division Council. The standard was originally published in 1960 and revised in 1967. Subsequent to the publication of 1967 edition, many changes had been agreed upon at international level which have been reflected in IS 1367 series of standards covering Technical supply conditions for threaded steel fasteners. Accordingly, IS 1963 was revised and published in 3 parts covering hexagon head bolts, hexagon head screws and hexagon nuts. The second revision of the standard was based OCR IS0 4034 : 1979 Hexagon nuts - Product grade C issued by ISO. This third revision has been made by the adoption of latest version of IS04034 published in 1986 as Part 3. The remain~ing parts of the standard, that is, Parts 1 and Part 2, have also been revised by adoption of corresponding latest version of international standards ( ISOs ). The following major~changes have been ~made in this revision: a) The range of sizes has been enlarged b) Non-preferred to cover sizes from M5 to M64; in separate table in line with IS0 4034;

sizes have been included

In the 1967 version of this standard, the width across flats for Ml0 and Ml2 size fasteners was However, in the 1983 version this width across specified as 17 mm and 19 mm respectively. flats was brought in line with IS0 4034 : 1979 and specified as 16 mm and 18 mm respectively for Ml0 and Ml2 size fasteners. Recognizing the fact that the new width acrossflat dimensions may not be implementable immediately, the Explanatory Note to 1983 version of the standard However, in the absence of specific coverage in the standard, made a reference to this aspect. Recognizing the difficulty of the new width across flat dimensions could not be implemented. immediate changeover to new width across flats, the Committee felt that definite time frame may be given to the manufacturers for changeover and accordingly, it has been decided that width across flats as per 1967 version, that is, 17 mm and 19 mm for Ml0 and Ml2 size fasteners shall be permitted till 31 December 1994. It is also understood that some manufacturers are already equipped and manufacturing as per new width across flat dimensions and supplies as per new specifications are encouraged. During this period, the manufacture of fasteners as per old version shall be phased out and by 1 January 1995, it is expected that the entire fastener industry would have switched over to newwidth across flat dimensions and with across flats as per old version shall not be permitted.

used in Indian Standards; attention


a)

In

the adopted

standard,

certain

terminology and conventions are not identical is specially drawn to the following: Standard and appear, referring in Indian

with those they

Wherever the words International should be read as Indian Standard;

to this standard,

b) Comma ( , j h?s been used as a decimal marker while practice is to use point ( . ) as the decimal marker.

Standards the current

( Continued on third cover )

IS 1363 ( Part 3 ) : 1992 IS0 4034 : 1986

Indian
HEXAGON

Standard

HEAD BOLTS, SCREWS AND NUTS OF PRODUCT GRADE C


PART 3 HEXAGON NUTS ) ( SIZE RANGE ( M5 TO M64

Third Revision )

Introduction
Standard is part of the complete drive fasteners. IS0 product

If, in special cases, specifications

other than those listed in this

This International standard prises a)

International Standard are required, they should be selected from existing International Standards, e.g. IS0 261, IS0 998/2, IS0 965, IS0 4759/l.

series on hexagon

The series com-

:
hexagon head bolts (IS0 4014, IS0 4015, IS0 4016and

References
Bolts, screws and nuts Symbols and

IS0 8765) b)

;
IS0 225, Fasteners head screws (IS0 4017, IS0 4018 and designations IS0 261, IS0 of dimensions.

hexagon

IS0 8676) c)

;
nuts (IS0 4632, IS0 4633, IS0 4034, plan.

general purpose

metric screw threads -

General

hexagon

IS0 4635, d)

IS0 4636, flange

IS0 8673, bolts (IS0

IS0 8674 and

IS0 8675);
IS0 8102

hexagon

4162, .ISO 8100,

IS0 09612, Mechanical properties with specified proof load values. IS0 965, Tolerances. IS0 3269, Fasteners Acceptance IS0 general purpose

of fasteners

Part 2: Nuts

and IS0 8104); e) f) hexagon hexagon flange screws; I1 flange nuts (IS0 4161, IS0 7043 and

metric

screw

threads

inspection. Electroplated coatings. 21

IS0 7044) g)

;
bolting (IS0 4775 and IS0 7411 to IS0 7417).

IS0 4042,

Threaded

components

structural

IS0 475911, product

Tolerances thread

for fasteners diameters >

Part 1: Bolts, screws < 150 mm and

and nuts with

1.6 and

grades A, B and C.

1
This

Scope

and field

of application
gives specifications horn M5 to M64 for hexagon inclusive and

IS0 8839,

Mechanical properties of fasteners - Bolts, screws,


metals. for bolts, screws,

studs and nuts made of non-ferrous international Standard diameters nuts with thread product grade C. IS0 8992, Fasteners studs and nuts. -

General requirements

1) 2)

These will form the subjects of future :r preseqt 7 L-C ;:;&: ? c:r.3it.

hlernational

Standarcs.

IS 1363 ( Part 3 ) : 1892 IS0 4034 : 1988

Dimensions

300 lSO 77%


_. m'

Countersink at start of thread permissible

Table 1 -

Preferred sizes

Dimensions

in millimetres -v

1)

P = pitch of the thread.

IS 1363 ( Part 3 ) f 1992 IS0 4034 : 1986

Table

2 -

Non-preferred

sizes Dimensions in millimetres

Thread size, d P) d, e m min. min. max. min.


m

Ml4 2 19.2 22,78 13.9

Ml8 25 24,9 2956 16.9

M22 2.5 31.4 3729

M27 3 38 45,2 1 24,7 22.6 18.1 41 40

M33 3,5 46.6 55,37

M38 4 55.9 6644

M45 4,5 64,7 76,95 1 36.9 1

M52 5 74,2 88,25 42,9

MW 5.5 83.4 99,21 48.9

1 20.2 1 18,l
14.5 34 33

1 12.1
9.7 21 20.16

1 15.1
12,l

1 29.5 1 27.4
21.9 56 49

1 34.3 1 31.8
25,4 66 58.8

1 34,4
27.5 70 68.1

1 46.4
32,3 86 78.1

1 46,4
37.1 90 87.8

min. nom. = max. min.

27 26.16

1)

P = pitch of the thread.

Specifications

and reference
Table

standards
3 Specifications and reference standards Steel IS0 9992 7H IS0 261, IS0 965

Material General reauirements Thread International Standard Tolerance International Standards Class Mechanical properties

I I

I
I

d < M16: 5 Ml6 <d< M39:4,5 d > M39: as agreed d < M39: IS0 89812 d > M39: as agreed C fS0 4759/l As processed

International Standards Product grade International Standard

Tolerances

Finish

Requirements for electroplating are covered in IS0 4642. If different electroplating requirements are desired or if requirements are needed for other finishes, they should be negotiated between customer and supplier.

Acceptability

For acceptance procedure, see IS0 3269.

Designation
of a hexagon - 5 nut with thread size d = Ml2 and propertyclass) 5:

Example for the designation Hexagon nut IS0

4034 - Ml2

1 i The designation symbols for the property classes according to IS0 898/2 can also be used for thread sizes above M39 provided that the finished product has all the properties assigned to the designation symbols in IS0 898/2.

Reprography

Unit,

BIS, New Delhi,

India

( Continued from second cover ) In this adopted standard, reference appears to certain International Standards for which Indian The corresponding Indian Standards which are to be substituted in their Standards also exist. place are Jisted below along with their degree of equivalence for the editions indicated: International Standard IS0 225 IS0 261 IS0 965* IS0 965/l IS0 965/2 Corresponding Indian Standard IS 8535 : 1987 Bolts, screws, nuts and accessories Terminology and nomenclature ( first revision ) IS4218 ( Part 2 ) : 1976 IS0 metric screw threads: Part 2 Diameter pitch combinations ( first revision ) IS0 general Tolerances purpose metric screw thread threads: Technically equivalent Technically equivalent Technically equivalent TechnicaHy equivalent Technically equivalent Degree of Equivalence Identical Technically equivalent

IS 4218 ( Part 4 ) : 1976


Part 4 Tolerancing IS 4218

IS0 metric screw system ( first revision )

( Part 6 ) : 1978 IS0 metric screw threads: Part 6 Limits of sizes for commercial bolts and nuts ( diameter range 1 to 52 nim ) ( first revision )

IS0 965/3 IS0 3269

IS 4218 ( Part 5 ) : 1979 IS0 metric screw threads: Part 5 Tolerances ( first revision )
IS 1367

( Part 17 ) Technical supply conditions for threaded steel fasteners : Part 17 Acceptance criteria ( under preparation )

IS0 4042

IS 1367

( Part 11 ) Technical supply conditions for threaded steel fasteners : Part 11 Electroplated fasteners ( under coatings eon threaded steel preparation ) ( Part 2 ) : 1979 Technical supply conditions for threaded steel fasteners : Part 2 Product grades and tolerances ( second revision )

IS0 4759-l

IS 1367

Technically equivalent Technically equ iva lent Equivalent

IS0 8839

IS

Mechanical properties of fasteners - Bolts, screws, studs and nuti made of non-ferrous metals ( under preparation j

IS0 8992

HIS1367 ( Part 1 ) : 1980 Technical supply conditions for threaded steel fasteners : Part 1 Introduction and general information ( second revision )

ALTERATION ln clause 5, the designation of hexagon nut may be read as Hexagon IS0 4034 - Ml 2 - 5 in place of Hexagon nut IS0 4034 - M12-nut IS 1363 ( Part 3 ) 5.

* IS0 965 has since been revised into parts. However, relevant parts have been shown in the references.

Burean

of Idiam

Staodards

BIS is a statutory institution established under the Bureau of Indian Standardr Acf, 1986 to promote harmonious development of the activities of standardization, marking and quality cbttiBcation of goods and attending tar connected matters in the country.
Copyright BIS

has the copyright of all its publications. No part of these publications may be reproduced in any form without the prior permission in writing of BIS. This does not preclude the free use, in the course of implementing the standard, of necessary details, such as symbols and sizes, type Enquiries relating to copyright be addressed to the Director or grade designations. ( Publications ), BIS.
Revision of Indian Standards

Indian Staddards are reviewed periodically and revised, when necessary and amendments, if any, are issued from time to time. Users of Indian Standards should ascertain that they are in possession of the latest amendments or edition. Comments on this Indian Standard may be sent to BIS giving the following reference. Dot : No. LM 14 ( 0161)

Amendmenta lsaaed Since Poblicatiom

Amend No.

Date of Issue

Text Affected

BUREAU OF INDIAN STANDARDS Headquarters: Manak Bhavan, 9 -Bahadur Shah Zahr Marg, New Delhi 110002 Telephones : 331 01 31, 331 13 75 Regional O&es : Central : Manak Bhavan, 9 Bahadur Shah Zafar Marg NEW DELHI l-10002 Eastern : l/l4 C. I. T. Scheme VII M,~V. I. P. Road, Maniktols CALCUTTA 7ooo54
Northern

Telegrams : Manaksanstha ( Common to all O&es ) Telephone 331 01 31 331 13 75 37 84 99, 37 85 61, 37 86 26, 37 86 62 53 38 43, 53 16 40, 53 23 84

: SC0 445-446, Sector 35-C. CHANDIGARH

160036

Southern : C. I. T. Campus, IV Cross Road, MADRAS 600113 Western : Manakalaya, E9 MIDC, Marol, Andheri ( East ) BOMBAY 400093

235 02 16, 235 04 42, I 235 15 19, 235 23 -15 632 92 95, 632 78 58, 632 78 91, 632 78 92

Branches : AHMADABAD, BANGALOkE, BHOPAL, BHUBANESHWAR, COIMBATORE, PARIDABAD, GHAZIABAD, GUWAHATI, HYDERABAD, JAIPUR, KANPUR, LUCKNOW, PATNA, THIRUVANANTHAPURAM.

Rcprogrsphy Unit, BE, New Delhi, India

Das könnte Ihnen auch gefallen