Beruflich Dokumente
Kultur Dokumente
Cable Pulling
Greenlee offers high-quality and durable cable pulling equipment designed to get the job done. For simple, straight shots to pulls with multiple bends and offsets, having Greenlee's cable pullers on the jobsite is a sure way to make your job faster, safer and easier in any application.
151
FEATURED Products
NEW UG5 Ultra Glider Cable Lubricating
156
Ultra Tugger 8 Cable Puller
159
Tugger 640 Cable Puller
169
Tray -Type Sheaves
Registered: The color green for manual and power-operated cable pullers is a registered trademark of Greenlee Textron Inc.
www.greenlee.com
ULTRA FEEDER
Cable Pulling
sPeCiFiCatioNs Power supply speed Maximum tractive Force 115 VAC, 15 amps, 60 Hz 4-36 feet per minute (1.2-11 meters per minute) Single Cable: 200 lbs. (.9 kN) All Cables: 800 lbs. (3.5 kN)
Cable Capacity Quantity size 8 x 250 MCM (120 mm2) 6 x 500 MCM (240 mm2) 5 x 750 MCM (300 mm2) reel Weight Capacity 25,000 lbs. total (11,300 kg) size 41" long x 27.5" wide x 37.5" high (1040 mm x 699 mm x 953 mm) Weight 285 lbs. (130 kg)
150
= ReplacemenT paRT
= accessoRy
www.greenlee.com
Cable Pulling
The Greenlee UG5 Ultra Glider is the new way to effectively apply cable lube during cable installation. The Ultra GLIDER has several advantages over the manual method used by most contractors today. Applies lube more evenly around the cable and more consistently than can be done by hand. This reduces the force required by the cable puller and reduces the chance for damage to the cable. During a cable pull, the person feeding the cable usually can also operate the Ultra GLIDER, which reduces the need for one person on the job. Eliminates the need for a person to place their hands near the point where the cable enters the conduit or duct. Eliminates the mess and slippery surfaces associated with manual cable lubrication. Applicators clean easily with water. Power unit and hose do not require cleaning between jobs. 3 pump speeds make it easy to match the lube rate to the needs of the pull.
Cat. No. UG511S UG511T UG511ST UG512S UG512T UG512ST UG511 UG512 UGSAK UGTAK UGSA150 UGSA200 UGSA250 UGSA300 UGSA350 UGSA400 UGSA500 UGSA600 UGTA075 UGTA100 UGTA125 UGTA150 UGTA200 UGTA250 UGTA300 UGTA350 UGTA400 12656 UPC No. 10353 10355 10356 10357 10359 10360 10354 10358 10252 10253 10287 10289 10291 10293 10295 10297 10304 10311 10284 10285 10286 10278 10279 10280 10281 10282 10283 12656 DesCriPtioN ULTRA-GLIDER 120V with UGSAK slip-in applicator kit ULTRA-GLIDER 120V with UGTAK threaded applicator kit ULTRA-GLIDER 120V including slip-in applicator kit UGSAK & threaded applicator kit UGTAK ULTRA-GLIDER 12V with UGSAK slip-in applicator kit ULTRA-GLIDER 12V with UGTAK threaded applicator kit ULTRA-GLIDER 12V including slip-in applicator kit UGSAK & threaded applicator kit UGTAK ULTRA-GLIDER 120V ASSEMBLY without applicators ULTRA-GLIDER 12V ASSEMBLY without applicators Slip-In Applicator Kit (Includes 2", 2-1/2", 3", 3-1/2" and 4" applicators with case) Threaded Applicator Kit (Includes 2", 2-1/2", 3", 3-1/2" and 4" applicators with case) 1-1/2" Slip-In Applicator Assembly 2" Slip-In Applicator Assembly 2-1/2" Slip-In Applicator Assembly 3" Slip-In Applicator Assembly 3-1/2" Slip-In Applicator Assembly 4" Slip-In Applicator Assembly 5" Slip-In Applicator Assembly 6" Slip-In Applicator Assembly 3/4" Threaded Applicator Assembly 1" Threaded Applicator Assembly 1-1/4" Threaded Applicator Assembly 1-1/2" Threaded Applicator Assembly 2" Threaded Applicator Assembly 2-1/2" Threaded Applicator Assembly 3" Threaded Applicator Assembly 3-1/2" Threaded Applicator Assembly 4" Threaded Applicator Assembly 20' Extension Hose (MAxIMUM ExTENSIoN IS 20')
USA Tel: 800.435.0786 Fax: 800.451.2632 Canada Tel: 800.435.0786 Fax: 800.524.2853
sPeCiFiCatioNs
Dimensions Depth: 17" (0.43 m) Width: 18" (0.45 mm) Height: 39" (1 mm) 24 lbs. (11 kg) 8" (20 cm) 10' (3 m) T ype: Sealed lead acid rechargeable battery DC output: 12-Volt Weight: 14.5 lbs. (6.6kg) Battery Life: Three to four 5 gallon buckets per charge AC output: 120-Volt Amps: 6 Amps
= ReplacemenT paRT
= accessoRy
151
www.greenlee.com
CABLE PULLERS
Cable Pulling
6800
6501
6001
640
766 UT2
152
= ReplacemenT paRT
= accessoRy
www.greenlee.com
Cable Pulling
The Versi-Boom Plus System can reach into a man-hole, yet allow the operator to run the puller from above. The equipment used is included in 6805a, 6805a-22, 6505, 6505-22, 6005 and 645 packages.
Operator is making an upward pull from the box using the puller and Versi-Boom System attached to the mobile carriage. The equipment used is included in packages 6805a, 6805a-22, 6505, 6505-22, 6503, 6005, 6004, 645 and 643. Rope is not included.
Operator is making a downward pull from the box using the puller with the chain mount (or vise chain unit) mounted onto the conduit. The equipment used is included in packages 6801, 6501, 6501-22, 6005, 6004, 6001, 6001-22, 645, 643, 642, 640 and 640-22. Rope is not included. USA Tel: 800.435.0786 Fax: 800.451.2632 Canada Tel: 800.435.0786 Fax: 800.524.2853
Operator is making an upward pull from the box using the puller and Versi-Boom System attached to the T stand. The equipment used is included in packages 6805a and 6802. Rope is not included.
Operator is making a downward pull from the box using the puller with the floor mount anchored to the floor. The equipment used is included in packages 6805a, 6805a-22, 6802, 6802-22, 6800, 6800-22, 6505, 6505-22, 6005, 6004, 645, 643 and 642. Rope is not included.
Operator is making an upward pull from the box using the puller and Versi-Boom Plus System attached to the mobile carriage. The equipment used is included in packages 6805a, 6805a-22, 6505, 6505-22, 6005 and 645. Rope is not included.
= ReplacemenT paRT
= accessoRy
153
www.greenlee.com
Package Components
Cable Pulling
6800 6801 6803 6803B 6805a 6805B 6800-22 6805a-22 6805B-22 6500 6501 6503 6505 6500-22 6505-22
UT5-22 07924 00865 02846 00870 00871 00864 00863 00835 00791 00781 00782 00784 00865 02846 00870 00871 00864 00863 00835 00791 00781 00782 00784 00799 00804 00811 00820 11152 23362 23405
08000
15000
29631
02846
154
= ReplacemenT paRT
= accessoRy
www.greenlee.com
Package Components
Cable Pulling
Tugger - 4,000 lb
110 VaC
640 643 645
220 VaC
6001-22
220 VaC
640-22
6001-22 31466 640 640-22 6037 29631 11230 11145 00791 00864 00863 00835 03661 00781 00782 00783 00784 00799 00804 00811 00815 00820 11152 651 35300 37663 35605 29631 11230 11145 00791 00864 00863 00835 03661 00781 00782 00783 00784 00799 00804 00811 00815 00820 11152 15325
11145
00864
651
00791
00804
00835 00871
= ReplacemenT paRT
= accessoRy
155
www.greenlee.com
Cable Pulling
NRTL/C
6805a
8,000 (35.8 kN) lbs. pulling force. Pulling speed ranges from 9 fpm at 2,000 lbs. to 6 fpm at 8,000 lbs. Mobile Versi-Boom system provides fast set-up with no anchors to set or chains to mount. Boom uses 3" rigid steel conduit for easy length adjustment to pull 10 to 20 feet (3 to 6 m) of cable out of the box fast and easy. Direct gear drive Easy to move around jobsite with mobile carriage. Patented
Cat. No. 6800 6800-22 6801 6803 UPC No. 00985 03196 00986 12824 DesCriPtioN Ultra Tugger 8 Cable Puller with Standard Force Gauge, and Floor Mount Same as 6800, except 220 VAC 50 Hz Ultra Tugger 8 Cable Puller with Standard Force Gauge, and Conduit Chain Mount Ultra Tugger 8 Cable Puller Basic Package. Includes standard force gauge, wheeled carriage, 4 ft. (1.2 m) boom, boom mount and nose unit, 2-1/2", 3" and 4" slip-in couplings, 2-1/2", 3" and 4" screwon couplings. Rope and storage box are optional. Same as 6803 plus 3048 Storage Box and 603 Casters Ultra Tugger 8 Cable Puller Deluxe Package. Same as 6503 plus 3-ft. (.9 m) boom, elbow unit and floor mount. Rope and storage box are optional. Same as 6805A plus 3048 Storage Box and 603 Casters Same as 6805A, except 220 VAC 50 Hz Same as 6805A-22 plus 3048 Storage Box and 603 Casters Deluxe Force Gauge (see page 163) Foot Switch (see page 164) T Stand 3-1/2" Slip-in Coupling 3-1/2" Screw-on Coupling Rope Stand Pull Rope 7/8" x 300' (22.2 mm x 91 m) Pull Rope 7/8" x 600' (22.2 mm x 182 m) Pull Rope 7/8" x 1,200' (22.2 mm x 365 m)
12133 02565 12131 03201 12132 00967 24821 00867 00815 00783 34362 34136 34137 34138
6805a-22 6805B-22 00967 445 00867 00815 00783 654 34136 34137 34138
6803 6800
sPeCiFiCatioNs
Maximum: 8,000 lbs. (35.8 kN) Continuous: 6,500 lbs. (28.9 kN Dimensions Length: 11.5" (292 mm) Width: 26" (660 mm) Heights 120V models: 6.75" (172 mm) 220V models: 10.0" (254 mm) Weight 86 lbs. (39 kg) (08000 only) Pulling speed Feet (Meters) Per Minute No Load: 9 fpm (2.7 mpm) At 2000 lbs. (0.9 kN): 8 fpm (2.4 mpm) At 4000 lbs. (1.8 kN): 7.5 fpm (2.3 mpm) At 6000 lbs. (2.7 kN): 7 fpm (2.1 mpm) At 8000 lbs. (3.6 kN): 6 fpm (1.8 mpm) Drive Motor 1-1/2 HP (1.1 kW) Power 8000, 6800, 6801, 6803, 6803B, 6805A, 6805B =120 VAC 60Hz 20A requirements UT8-22, 6800-22, 6805A-22, 6805B-22 = 220 VAC 50Hz required 7/8" diameter (22.2 mm); Double-Braided Polyester Composite Rated rope at 32,000 lbs. (142 kN) minimum breaking strength Pulling Force
6801
Note: Rope is a very critical link in the cable pulling system. See page 171 for proper pulling rope selection. *See page 154 for UT8 component list
156
= ReplacemenT paRT
= accessoRy
www.greenlee.com
Cable Pulling
NRTL/C
6505
5,000 lbs. (22.3 kN) pulling force, enough power to pull most 500 kcmil (240 mm2) jobs of 500 feet (152 m) or less. Pull speed range of 9 to 14 fpm (2.7 to 4.3 mpm) will complete most 500 ft. (152 m) pulls in 1 hour or less. Mobile Versi-Boom system provides fast setup with no anchors to set or chains to mount. Boom uses 3" rigid steel conduit for easy length adjustment to pull 10 to 20 feet (3 to 6 m) of cable out of the box fast and easy. Use 6501 Ultra Tugger 5,000 lb. (22.3 kN) capacity cable puller power unit with current 6805A Ultra Tugger wheeled carriage and boom to pull cable faster. Patented.
Cat. No. 6500 6500-22 6501 6503 UPC No. 12822 12823 11221 11222 DesCriPtioN Ultra Tugger 5 Cable Puller Power Unit only with standard force gauge and floor mount Same as 6500, except 220 VAC 50 Hz Ultra Tugger 5 Cable Puller Power Unit with standard force gauge and chain mount and vise chains Ultra Tugger 5 Cable Puller Basic Package. Includes standard force gauge, wheeled carriage, 4 ft. (1.2 m) boom, boom mount and nose unit, 2-1/2", 3" and 4" slip-in couplings, 2-1/2", 3" and 4" screw-on couplings. Rope and storage box are optional. Ultra Tugger 5 Cable Puller Deluxe Package. Same as 6503 plus 3-ft. (.9 m) boom, elbow unit and floor mount. Rope and storage box are optional. Same as 6505, except 220 VAC 50 Hz Deluxe Force Gauge (See page 163) Foot Switch (See page 164) T Stand 3-1/2" Slip-in Coupling 3-1/2" Screw-on Coupling Rope Stand Storage Box Casters 2 Rigid, 2 Swivel Pull Rope, 3/4" x 300 ft. (19.1 mm x 91 m) Double-Braided Composite Pull Rope, 3/4" x 600' (19.1 mm x 182 m) Pull Rope, 3/4" x 1,200' (19.1 mm x 365 m)
6505 6505-22 00967 445 00867 00815 00783 654 3048 603 35098 35100 35101
11223 32743 00967 24821 00867 00815 00783 34362 23362 23405 35098 35100 35101
USA Tel: 800.435.0786 Fax: 800.451.2632 Canada Tel: 800.435.0786 Fax: 800.524.2853
sPeCiFiCatioNs
6503 Maximum: 5,000 lbs. (22.2 kN) Continuous: 4,000 lbs. (17.8 kN) Dimensions Length: 11.5" (292 mm) Width: 26" (660 mm) Height: 6.75" (172 mm) Heights 120V models: 6.75" (172 mm) 220V models: 10.0" (254 mm) Weight 84 lbs. (38 kg) (15000 only) Pulling speed Feet (Meters) Per Minute No Load: 14.5 fpm (4.4 mpm) At 4000 lbs. (1.8 kN): 11 fpm (3.4 mpm) At 5000 lbs. (2.3 kN): 9.5 fpm (2.9 mpm) Drive Motor 1-1/2 HP (1.1 kW) Power requirements required rope 15000, 6501, 6503, 6505 120 VAC 60Hz 20A UT5-22, 6501-22, 6505-22 220 VAC 50Hz 3/4" (19.1 mm) Double-Braided Polyester Composite - Rated at 20,000 lb. (88.8 kN) minimum breaking strength Pulling Force
6501
Note: Rope is a very critical link in the cable pulling system. See page 171 for proper pulling rope selection. *See page 154 for UT5 component list
= ReplacemenT paRT = accessoRy
157
www.greenlee.com
Cable Pulling
NRTL/C
6005
Pull up to 6,500 lbs. (28.9 kN) with less than 27 lbs. (120 N) of operator effort. Unique floor mounting attachment for quick, reliable setup. Leaf-type mounting chains won't twist when tightening. Heat-treated steel serrated gripper feet for secure mounting to conduit. Force Gauge included to constantly monitor the pull. Right-angle sheave allows the operator to stand out of the direct line of force. Audio alarm high force warning and circuit breaker shut off at maximum force for added safety. Tapered capstan and patented rope guidance system for better control of the rope when feeding onto the capstan. Patented.
Cat. No. 6001 6001-22 6004 UPC No. 29627 31466 56358 DesCriPtioN Super Tugger Cable Puller Power Unit, Includes force gauge and vise chains Same as 6001 except 220 VAC 50 HZ Super Tugger Complete Puller Package, Includes 6001 Super Tugger, Floor Mount, Mobile Carriage, Boom Mount, 4' Boom Tube, Nose Unit, 2 1/2", 3", 3 1/2", 4" Slip-in and Screw-on Couplings and Storage Trays Super Tugger Complete Puller Package, Includes 6001 Super Tugger, Floor Mount, Mobile Carriage, Boom Mount, 4' Boom Tube, Nose Unit, 3' Boom Tube, Elbow Unit, 2 1/2", 3", 3 1/2", 4" Slip-in and Screw-on Couplings and Storage Trays Double-Braided Composite Rope 3/4" 300' (19.1 mm 91 m) Double-Braided Composite Rope 3/4" 600' (19.1 mm 182 m) Double-Braided Composite Rope 3/4" 1,200' (19.1 mm 365 m) Foot Switch (See page 164) Storage Box (See page 360)
6005
56359
sPeCiFiCatioNs
Maximum: 6,500 lbs. (28.9 kN) Continuous: 4,500 lbs. (20 kN) Dimensions Length: 20-3/4" (527 mm) Width: 22-1/2" (572 mm) Height: 12" (305 mm) Weight 6001, 6001-22: 108 lbs. (49 kg) 6003: 454 lbs. (206 kg) 6000, 6000-22: 550 lbs. (250 kg) 6006, 6006-22: 612 lbs. (278 kg) Pulling speed Feet (Meters) Per Minute No Load: 16.5 (5) At 2000 lbs.: (8.8 kN) 11 (3.4) At 4000 lbs.: (17.9 kN) 7.5 (2.3) At 6000 lbs.: (26.7 kN) 6 (1.8) Drive Motor 1-1/2 HP (1.1 kW) Power requirements 6001, 6004, 6005 120 VAC 16Hz 20A 6001-22 220 VAC 50Hz required rope 3 /4" (19.1 mm) Double-Braided Composite Rated at 26,000 lbs. (115.6 kN) 6001 Pulling Force
6004
Note: Rope is a very critical link in the cable pulling system. See page 171 for proper pulling rope selection.
158
= ReplacemenT paRT
= accessoRy
www.greenlee.com
Cable Pulling
NRTL/C
An economical puller with enough power for most jobs. Lighter weight for easier mounting in tough applications. Leaf-type mounting chains wont twist when tightening. Unique floor mounting attachment for quick reliable setup. Right-angle sheave allows the operator to stand out of the direct line of force. Audio alarm high force warning and circuit breaker shut off at maximum force for equipment protection and added safety. Tapered capstan and patented rope guidance system for better control of rope. Patented.
645
56361
Tugger Cable Puller Power Unit. Includes vise chains Same as 640 except 220 VAC 50 HZ Tugger Complete Puller Package, Includes 640 Tugger, Cable Puller, Floor Mount, Mobile Carriage, Boom Mount, 4' Boom Tube, Nose Unit, 2", 3", 4" Screw-on Couplings, Screw-on Coupler Adapter, 2 1/2", 3", 4" Slip-in Couplings and Storage Trays Tugger Complete Puller Package, Includes 640 Tugger, Cable Puller, Floor Mount, Mobile Carriage, Boom Mount, 4' Boom Tube, Nose Unit, 3" Boom Tube, Elbow Unit, 2", 3", 4" Screw-on Couplings, Screw-on Coupler Adapter, 2 1/2", 3", 4" Slip-in Couplings, Storage Trays and 12" Hook Sheave 640 Capstan Retrofit Kit includes rope ramp, pivotal arm and tapered capstan. For units with NZ serial prefixes. Force Gauge for 120 VAC 640 cable puller Force Gauge for 220 VAC cable puller Double-Braided Composite Rope 9/16" 300' (14.3 mm 91 m) Double-Braided Composite Rope 9/16" 600' (14.3 182 m) Double-Braided Composite Rope 9/16" 1,200 (14.3 mm 365 m) Foot Switch (See page 164)
sPeCiFiCatioNs
Maximum: 4,000 lbs. (17.9 kN) Continuous: 2,500 lbs. (11.1 kN) Dimensions Length: 21" (533 mm) Width: 21" (533 mm) Height: 12" (305 mm) Weight 640, 640-22 82 lbs. (38 kg) 676 373 lbs. (170 kg) 642 330 lbs. (150 kg) 686, 686-22 427 lbs. (194 kg) Pulling speed Feet (Meters) Per Minute No Load 35 (10.67), At 2000 lbs. (8.8 kN) 16 (4.87) At 4000 lbs. (17.9 kN) 6 (1.83) Drive Motor 1-1/2 HP (1.1 kW) Power requirements 640, 643, 645 120 VAC 20A 640-22 220 VAC 50Hz required rope 9/16" (14.3 mm) Double-Braided Composite: Rated at 16,000 lbs. (71.1 kN) Pulling Force
Canada Tel: 800.435.0786 Fax: 800.524.2853 International Tel: +1.815.397.7070 Fax: +1.815.397.9247
Note: Rope is a very critical link in the cable pulling system. See page 171 for proper pulling rope selection.
= ReplacemenT paRT
= accessoRy
159
www.greenlee.com
Cable Pulling
Quick Latch System attaches to all conduit sizes with no loose parts. Adjustable elbow and extendable boom adjust easily to fit your job needs. Right Angle Sheave keeps operator out of direct line with the pulling rope. Dual Diameter capstan provides 2 pulling speeds. Cross Tube provides a solid base for setup and during pull. Integral Motor designed specifically for cable pulling applications. Circuit Breaker stops the puller motor if it becomes overloaded. Wheels provide easy movement around jobsite.
Cat. No. UT2 56362 2448 455 456 445 UPC No. DesCriPtioN 02010 56362 23273 23774 23777 24821 2,000 LB. Cable Puller Unit Trailer hitch adapter (fits 2" receiver) Storage Box 1/2" 300' (12.7 mm 91 m) Double Braided Rope 1/2" x 600' (12.7 mm 182 m) Double Braided Rope Foot Switch (See page 164)
sPeCiFiCatioNs
Pulling Force Drive Motor Weight Pulling speeds High Speed Capstan 1,000 lb. (455 kg) continuous Low Speed Capstan 2,000 lb. (909 kg) continuous 120 VAC, 50/60 Hz, 12 Amps 67 lbs. High speed Capstan No Load: 73 fpm (22 mpm) 500 lb. Load (227 kg) 36 fpm (11 mpm) 1,000 lb. Load (455 kg) 22 fpm (7 mpm) Low speed Capstan No Load: 41 fpm (12 mpm) 1,000 lb. Load (455 kg) 36 fpm (11 mpm) 2,000 lb. Load (909 kg) 22 fpm (7 mpm) 1/2" polyester (10,000 lb. minimum breaking strength) *Greenlee recommends that only low stretch polyester rope be used with the UT2. High stretch ropes can release large amounts of energy should they break during use. 1" or larger 3 x 500 kcmil cable 500 with 2 x 90 bends 3 x 500 kcmil cable 250 with 4 x 90 bends 8 x 4/0 AWG cable 300 with 3 x 90 bends
Pulling rope*
UP PULL
doWN PULL
SIdE PULL
UT2
Note: Rope is a very critical link in the cable pulling system. See page 171 for proper pulling rope selection.
160
= ReplacemenT paRT
= accessoRy
= new pRoducT
www.greenlee.com
Cable Pulling
Pull up to 1500 lbs. (6.7 kN) with only 30 lbs. (133 N) of crank handle force. Two-speed ratchet winder for fast, efficient operation. Has 200' (61 m) of steel aircraft cable. Completely self-contained and ready to operate.
Cat. No. 766 50954 13955 28280 UPC No. 18202 50954 14568 28280 DesCriPtioN Hand Crank Wire Puller 200' (61 m) spool of steel cable Shear Pin Crank Handle Assembly
sPeCiFiCatioNs Pulling Force size Weight Power Dimensions Maximum - 1500 lbs. (6.6 kN) 200' (61 m) pulling cable length 38 lbs. (17.2 kg) Manual - 2-Speed Hand Crank Length - 52" (1.32 m) Width - 18" (457 mm) Height - 10" (254 mm)
Adapt Greenlee 640 Tugger and 6001 Super Tugger to Ultra Tugger Wheeled Carriage and Boom for faster and easier cable puller setups. Wheeled carriage and boom provides fast setup with no anchors to set or chains to mount. Boom uses 3" rigid steel conduit for easy length adjustment to pull 10 feet (3m) of cable out of the box fast and easy. optional Elbow Unit and Boom available to reach into manholes or pull up to 20 feet (6 m) of cable out of the box. Patent pending.
sPeCiFiCatioNs Weight Length Width Height Use With Load rating 198 lbs. (90 kg) 91-1/2" (232 cm) 27" (69 cm) 38-1/2" (98 cm) Greenlee 640 and 6001 Cable Pullers 6500 lbs. (28.9 kN)
USA Tel: 800.435.0786 Fax: 800.451.2632 Canada Tel: 800.435.0786 Fax: 800.524.2853 International Tel: +1.815.397.7070 Fax: +1.815.397.9247
11147
00863
= ReplacemenT paRT
= accessoRy
161
www.greenlee.com
TUGGER ACCESSORIES
Cable Pulling
sPeCiFiCatioNs Capacity Dimensions Weight Pulling speed, Ultra tugger 5 Pulling speed, Ultra tugger 8 Power 0 to 2,500 lbs. (11.1 kN) pulling force in high speed mode Height: 9.5" (241.3 mm); Width 13" (330.2 mm); Depth: 15.5" (393.7 mm) 46 lbs. (20.9 kg) No Load - 28 fpm (8.5 mpm); At 1200 lbs. (5.3 kN) - 25 fpm (7.6 mpm) No Load - 18 fpm (5.5 mpm); At 2000 lbs. (8.8 kN) - 16 fpm (4.9 mpm) 115 VAC, 15A Input; 115/230 VAC, 15/6A output
162
= ReplacemenT paRT
= accessoRy
www.greenlee.com
Cable Pulling
Use with UT2, 640, 6001, 6500 or 6800 cable pullers to add foot control. Foot pressure required to operate.
sPeCiFiCatioNs Power source Weight 120 VAC 9.5 lbs. (4.3 kg)
Slip-in Couplings
3" 2-1/2" 3-1/2" 4" 5"
Use to attach the Versi-Boom to the conduit. Couplings slip into the conduit and pin to the Versi-Boom. For use with the Versi-Boom system only.
Cat. No. UPC No. 00804 00811 00815 00820 00827 size 2.5" 3" 3.5" 4" 5" WeigHt 6 lbs (2.7 kg) 7 lbs (3.2 kg) 9 lbs (4.1 kg) 11 lbs (5 kg) 13 lbs (5.8 kg)
Optional
Screw-on Couplings
2" 2-1/2" 3" 3-1/2" 4" adapter
Use to attach the Versi-Boom to the conduit when pulling from overhead. The coupling and adapter threads onto the conduit and pins to the Versi-Boom. The screw-on coupling and adapter must be used together. one adapter fits all of the screw-on couplings.
Screw assembly
size 2-1/2", 3", 3-1/2", and 4" 2" 2-1/2" 3" 3-1/2" 4"
WeigHt 22 lbs (10.0 kg) 2.1 lbs (1.0 kg) 3.1 lbs (1.4 kg) 4.4 lbs (2.2 kg) 5.6 lbs (2.5 kg) 5.7 lbs (2.6 kg)
= ReplacemenT paRT
= accessoRy
163
www.greenlee.com
Cable Pulling
For use with any Greenlee cable puller. Strong, welded steel frames. Forged steel closure type hooks with 1" (25.4 mm) opening. All three sheaves are aluminum alloy with self-lubricating bearings.
sHeaVe DiaMeter DesCriPtioN oll Pin R heave Pin S heave Pin Clip S heave Unit S oke Frame Y 8012 12" (304.8 mm) Cat. No. UPC No. 50700 50700 00838 00838 50302 50302 00843 00843 00854 00854 8018 18" (457.2 mm) Cat. No. UPC No. 50700 50700 00846 00846 50302 50302 00844 00844 00855 00855 8024 24" (609.6 mm) Cat. No. UPC No. 50700 50700 00850 00850 50302 50302 00845 00845 00856 00856
sPeCiFiCatioNs Cat. No. UPC No. 8012 00872 8018 00873 8024 00874
oUtsiDe DiaMeter 12" (304.8 mm) 18" (457.2 mm) 24" (609.6 mm)
iNsiDe raDiUs 3-7/8" (98.4 mm) 7" (177.8 mm) 9-7/8" (250.8 mm)
WiDtH 5" (127 mm) 6" (152.4 mm) 6-1/2" (165.1 mm)
WeigHt 28 lbs (12.7 kg) 44 lbs (19.9 kg) 67 lbs (30.3 kg)
MaxiMUM rateD CaPaCity 8,000 lbs. (35.8 kN) 8,000 lbs. (35.8 kN) 8,000 lbs. (35.8 kN)
sPeCiFiCatioNs Maximum rated Capacity Weight 4,000 lbs. (17.8 kN) 650 - 8.8 lbs. (4 kg) 651 - 15 lbs. (6.8 kg) 652 - 25 lbs. (11.3 kg) 653 - 35 lbs. (15.9 kg)
Sheave Pin 16797 Sheave Pin Clip (2) 50302 Sheave 15362 Sheave Bushing (2) 16798 Yoke Frame 16799
sPeCiFiCatioNs Maximum rated Capacity Weight 4,000 lbs. (17.8 kN) 45 lbs. (20.4 kg)
164
sHeaVe DesCriPtioN Sheave Pin Sheave Pin Clip Sheave Sheave Bushing Yoke Frame
= ReplacemenT paRT
= accessoRy
Note: Rope is a very critical link in the cable pulling system. See page 171 for proper pulling rope selection.
www.greenlee.com
Cable Pulling
Welded steel frame with a series of sheaves to form a large radius. Yokes with cast steel closure-type hooks with a 1" (25.4 mm) opening. 5" (127 mm) wide aluminum alloy sheaves. Use with any cable puller whose maximum pulling force is 4,000 lbs. (17.8 kN) or less.
Cat. No. 636 637 638 631 UPC No. 17255 17260 17263 21572 DesCriPtioN 16" (406.4 mm) Radius Cable Sheave with 4 sheave wheels 24" (609.6 mm) Radius Cable Sheave with 6 sheave wheels 36" (914.4 mm) Radius Cable Sheave with 8 sheave wheels 48" (1219 mm) Radius Cable Sheave with 10 sheave wheels
sPeCiFiCatioNs Maximum rated Capacity Weight 4,000 lbs. (17.8 kN) 631 - 115 lbs. (52 kg) 636 - 49 lbs. (22 kg) 637 - 63 lbs. (29 kg) 638 - 85 lbs. (39 kg) 631 48" (1219 mm) Cat. No. UPC No. 17256 17256 50302 50302 16798 16798 15362 15362 17257 17257 21573 21573
sHeaVe raDiUs DesCriPtioN heave Pin S heave Pin Clip S heave Bushing S heave S oke Frame Y rame F
636 16" (406.4 mm) Cat. No. UPC No. 17256 17256 50302 50302 16798 16798 15362 15362 17257 17257 17258 17258
Qty. 4 8 2 4 2 1
637 24" (609.6 mm) Cat. No. UPC No. 17256 17256 50302 50302 16798 16798 15362 15362 17257 17257 17261 17261
Qty. 6 12 2 6 2 1
638 36" (914.4 mm) Cat. No. UPC No. 17256 17256 50302 50302 16798 16798 15362 15362 17257 17257 17264 17264
Qty. 8 16 2 8 2 1
Qty. 10 20 2 10 2 1
Canada Tel: 800.435.0786 Fax: 800.524.2853 International Tel: +1.815.397.7070 Fax: +1.815.397.9247
sPeCiFiCatioNs Maximum rated Capacity Weight 6,500 lbs. (28.9 kN) 28 lbs. (12.7 kg)
= ReplacemenT paRT
= accessoRy
165
www.greenlee.com
Feeding Sheaves
Cable Pulling
Yoke frame slides into the end of conduit and holds sheave, allowing the cable being fed into the conduit to smoothly roll over the sheave. 5" (127 mm) wide aluminum alloy sheave with self-lubricating bearings. Split tube for easy removal after cable is installed. See the Capacity Table (below).
Cat. No. 441-2 441-2-1/2 441-3 441-3-1/2 441-4 441-5 441-6 UPC No. 30183 30358 30188 30363 30347 30193 13460 DesCriPtioN Feeding Sheave for 2" conduit Feeding Sheave for 2-1/2" conduit Feeding Sheave for 3" conduit Feeding Sheave for 3-1/2" conduit Feeding Sheave for 4" conduit Feeding Sheave for 5" conduit Feeding Sheave for 6" conduit
sPeCiFiCatioNs rated Capacity See Capacity Table Below for details. Weight Width of shaft opening 441-2 9 lbs. (4.5 kg) 441-2 1.24" 441-2-1/2 11 lbs. (5 kg) 441-2-1/2 1.37" 441-3 14 lbs. (6.4 kg) 441-3 1.79" 441-3-1/2 17 lbs. (7.7 kg) 441-3-1/2 1.75" 441-4 19 lbs. (8.6 kg) 441-4 1.99" 441-5 26 lbs. (11.8 kg) 441-5 2.23" 441- 6 28 lbs. (12.7 kg) 441- 6 2.75" sHeaVe CoNDUit size DesCriPtioN heave Pin S heave Pin Clip (2) S heave S rame F 441-2 2" CoNDUit Cat. No. UPC No. 25160 25160 50302 50302 15362 15362 30184 30184 441-2-1/2 2-1/2" CoNDUit Cat. No. UPC No. 25160 25160 50302 50302 15362 15362 30359 30359
441-3 3" CoNDUit Cat. No. UPC No. 25160 25160 50302 50302 15362 15362 30189 30189
441-3-1/2 3-1/2" CoNDUit Cat. No. UPC No. 25160 25160 50302 50302 15362 15362 30364 30364
441-4 4" CoNDUit Cat. No. UPC No. 25160 25160 50302 50302 15362 15362 30346 30346
441-5 5" CoNDUit Cat. No. UPC No. 25160 25160 50302 50302 15362 15362 30194 30194
UNOCCUPIED MANHOLE
UNOCCUPIED MANHOLE
ABOVE GROUND
UNOCCUPIED MANHOLE
CaPaCity taBLe aNgLe oF PULL 441-2 15 1750 lbs. 7.7 kN 30 900 lbs. 4.0 kN 45 650 lbs. 2.8 kN 60 500 lbs. 2.2 kN 75 450 lbs. 2.0 kN 90 450 lbs. 2.0 kN
441-2-1/2 1900 lbs. 8.4 kN 1000 lbs. 4.4 kN 700 lbs. 3.1 kN 550 lbs. 2.4 kN 500 lbs. 2.2 kN 500 lbs. 2.2 kN
441-3 6050 lbs. 26.9 kN 3150 lbs. 14.0 kN 2200 lbs. 9.7 kN 1800 lbs. 8.0 kN 1600 lbs. 7.1 kN 1550 lbs. 6.8 kN
441-3-1/2 6500 lbs. 28.9 kN 5050 lbs. 22.4 kN 3550 lbs. 15.7 kN 2900 lbs. 12.8 kN 2600 lbs. 11.5 kN 2500 lbs. 11.1 kN
441-4 6500 lbs. 28.9 kN 6500 lbs. 28.9 kN 5200 lbs. 23.1 kN 4200 lbs. 18.6 kN 3650 lbs. 16.2 kN 3500 lbs. 15.5 kN
441-5 6500lbs. 28.9 kN 6500 lbs. 28.9 kN 6500 lbs. 28.9 kN 6000 lbs. 26.6 kN 5500 lbs. 24.4 kN 5250 lbs. 23.3 kN
166
= ReplacemenT paRT
= accessoRy
Note: Rope is a very critical link in the cable pulling system. See page 171 for proper pulling rope selection.
www.greenlee.com
Cable Pulling
Fits in the end of conduit to shield the cable from sharp edges as it is being fed through. Rugged nylon resists abrasion.
Cat. No. 488-2 488-3 UPC No. 32928 32929 DesCriPtioN Nylon Cable Protector for 2" and 2-1/2" conduit Nylon Cable Protector for 3" - 6" conduit
sPeCiFiCatioNs Weight 488-2 - 0.08 lbs. (36 g) 488-3 - 0.2 lbs. (90 g)
Cable Guide
Position where cables are being pulled over sharp edges.
Cat. No. 489 UPC No. 32930 DesCriPtioN Nylon Cable Guide
sPeCiFiCatioNs Weight size 489 - .5 lbs. (227 g) 13" L x 3-1/4" W x 12" radius
Cable Puller Floor Mount for 640 Tugger and 6001 Super Tugger
Unique floor mounting attachment for quick, reliable setups. Heavy-duty welded steel construction for use with all Greenlee 640 & 6001 cable pullers. The only approved way to mount a cable puller to a concrete floor. Minimum 3,000 psi (205 bar) concrete required.
Cat. No. 6037 35607 UPC No. 35605 35607 DesCriPtioN
Cable Puller Floor Mount with four (4) 35607 wedge anchors 5/8" 6" (15.9 mm 152 mm) Wedge Anchor
sPeCiFiCatioNs Maximum rated Capacity Weight 6,500 lbs. (28.9 kN) 2.9 lbs. (1.4 kg)
= ReplacemenT paRT
= accessoRy
Note: Rope is a very critical link in the cable pulling system. See page 171 for proper pulling rope selection.
167
www.greenlee.com
Cable Pulling
Mounts directly to existing square light pole bolt patterns. Slotted mounting holes fit a wide range of bolt circle sizes. Tall enough to position sheave above most conduits. Rugged welded steel base structure. Allows user to install wires into outdoor light bases by pulling horizontally. Also can be used to feed wires into vertical light base conduit.
Cat. No. 459 UPC No. 89800 DesCriPtioN Light Base Sheave
sPeCiFiCatioNs overall Height Weight Bolt Circle Capability Maximum Mounting Bolt Dia. Pulling Capacity 14-1/2" (368 mm) 18 lbs. (8.2 kg) 7.8" (198 mm) to 14.8" (376 mm) diameter 1" (25 mm) diameter at 7.8" (198 mm) bolt circle 1-1/2" (38 mm) at 14.8" (376 mm) bolt circle 500 lbs. (227 kg)
CR25
Six nylon rollers provide smooth movement of cable and prevent cable damage. Pull pin makes opening and closing to insert and remove cables a simple one step operation. Adjustment clamp allows the CR25 to be swiveled and/or rotated into any position. Heavy duty 12 gauge cold rolled steel construction for durability and zinc dichromate finish prevents corrosion. Up to 20 network cables can be pulled at one time. Easily attaches to wooden framing members using a lag bolt and the hole in the mounting bracket of the CR25. May also be used with coax, NM, small size THHN, and similar cables.
sPeCiFiCatioNs roller opening size: Weight: 3" (76 mm) square 2 lb. (1 kg)
168
= ReplacemenT paRT
= accessoRy
Note: Rope is a very critical link in the cable pulling system. See page 171 for proper pulling rope selection.
www.greenlee.com
Cable Pulling
659
658 659
sPeCiFiCatioNs size Weight 658 12" (304.8 mm) long 658 11 lbs. (5 kg) 659 22" (558.8 mm) long 659 17 lbs. (7.7 kg)
3-3/8" 5-5/8"
Installed up through the bottom of the tray for easy removal after the cable is installed. Individual rollers keep rolling with each cable even after several cables have been installed in the tray. Steel ball bearing rollers for long life and less friction. Steel welded frame. Adjustment slots and universal mounting brackets.
Cat. No. 28170 UPC No. 28170 UPC No. 27383 27384 27386 27387 DesCriPtioN J-Hook DiMeNsioN a 6-5/16" (160.3 mm) 12-1/2" (317.5 mm) 18-11/16" (474.7 mm) 24-7/8" (631.8 mm)
sPeCiFiCatioNs Weight 2018S 8 lbs. (3.6 kg) 2024S 10 lbs. (4.5 kg) 2030S 13 lbs. (5.9 kg) 2036S 15 lbs. (6.8 kg) 20249R 41 lbs. (18.6 kg) Cat. No. UPC No. DesCriPtioN
2018R 11 lbs. (5 kg) 2024R 12 lbs. (5.4 kg) 2030R 13 lbs. (5.9 kg) 2036R 14 lbs. (6.3 kg) 20369R 53 lbs. (24 kg)
2024S
2018R
20249R
straigHt CaBLe roLLers 2018S 27383 Straight Cable Roller for 12" - 18" (304.8 - 457.2 mm) wide tray 2024S 27384 Straight Cable Roller for 20" - 24" (508 - 609.6 mm) wide tray 2030S 27386 Straight Cable Roller for 24" - 30" (609.6 - 762 mm) wide tray 2036S 27387 Straight Cable Roller for 30" - 36" (762 - 914.4 mm) wide tray raDiUs CaBLe roLLers 2018R 27388 Radius Cable Roller for 12" - 18" (304.8 - 457.2 mm) wide tray 2024R 27389 Radius Cable Roller for 20" - 24" (508 - 609.6 mm) wide tray 2030R 27390 Radius Cable Roller for 24" - 30" (609.6 - 762 mm) wide tray 2036R 27391 Radius Cable Roller for 30" - 36" (762 - 914.4 mm) wide tray rigHt aNgLe CaBLe roLLers 20249R 27392 Right Angle Rollers 24" (609.6 mm) radius 90 20369R 27393 Right Angle Rollers 36" (914.4 mm) radius 90
= ReplacemenT paRT
= accessoRy
169
www.greenlee.com
Cable Pulling
DesCriPtioN size Haines Roller 7" (177.8 mm) wide 6" (152.4 mm) dia. Expandable Roller Half Used to make 8" (203.2 mm) to 48" (1219.2 mm) wide roller
31926 31927
Coupling 3-1/2" (88.9 mm) dia. 3" (76.2 mm) long Mounting Clip Steel Conduit Use with 1-1/2" Rigid
Highly economical system of 1-1/2" steel conduit spindles, high-impact ABS plastic rollers and simple clips. Rollers snap in and out of clips fast and easy. Mounting clips fit onto the top of most I-Beam and C-Channel trays, so existing wire is not disturbed. 8" (203.2 mm) to 48" (1219.2 mm) wide rollers are available, using expandable roller halves and 3" (76.2 mm) PVC conduit. Use Greenlee Cable-Cream (see p. 172) to lube spindle and roller. This lubricant is compatible with all cable insulation types.
31930 31929
Spindle (includes 1-1/2" Rigid Conduit End Caps) x 40" (1016 mm) long End Cap Fits 1-1/2" Rigid Conduit
Rope Stands
Use to organize and rewind rope. Welded steel with washer and spring clip to hold rope reel on stand. International Tel: +1.815.397.7070 Fax: +1.815.397.9247
roPe staND UPC 3/16" roPe LeNgtH No. 4.8 mm 405 rope stand 21546 250' (76 m) Rope 600' (182 m) Rope 406 rope stand 21550 300' (91 m) Rope 600' (182 m) Rope 1,000' (305 m) Rope 3,000' (914 m) Conduit Measuring Tape Measuring Tape Cat./UPC No. 644 rope stand 15316 300' (91 m) 600' (182 m) 1,200' (365 m) 5,000' (1524 m) 654 rope stand 34362 300' (91 m) 600' (182 m) 1/4"
6.4 mm
3/8"
9.5 mm
3/4"
19.1 mm
7/8"
22.2 mm
654
39243
39244
39245
sPeCiFiCatioNs roPe staND MoDeL 405 406 644 654 WeigHt 5.2 lbs (2.4 kg) 7.8 lbs (3.5 kg) 11 lbs (5 kg) 32.1 lbs (14.6 kg) sPiNDLe DiaMeter 1.50" (38 mm) 0.62" (16 mm) 1.50" (38 mm) 1.90" (48 mm) MaxiMUM reeL DiaMeter 10" 13' 17" 24" MaxiMUM reeL WiDtH 6" 9" 16" 19"
170
= ReplacemenT paRT
= accessoRy
www.greenlee.com
Cable Pulling
Custom-made to greenlee specifications to provide 4:1 safety Factor required for cable pulling. Double-braided inner core with an extra double-braided outer jacket or f added strength and less stretch; white with green tracer. Rot and mildew resistant. Factory spliced eyes at both ends. Lowest stretch. Select a rope with a maximum rated capacity that meets or exceeds the cable pullers maximum pulling force.
roPe DiaMeter FoR THE 805 PULLER (9.5 mm) FoR THE UT2 PULLER (12.7 mm)
roPe LeNgtH 300' 91 m 600' 182 m 1,200' 365 m 300' 600' 91 m 182 m
Cat. No. 450 451 452 455 456 35283 35284 35285
UPC No. 23773 23775 23776 23774 23777 35283 35284 35285
MaxiMUM rateD CaPaCity 1200 lbs. 3.6 kN 1200 lbs. 3.6 kN 1200 lbs. 3.6 kN 2,200 lbs. 8.9 kN 2,200 lbs. 8.9 kN 4,000 lbs. 17.8 kN 4,000 lbs. 17.8 kN 4,000 lbs. 17.8 kN
aVerage BreakiNg streNgtH 3700 lbs. 3700 lbs. 3700 lbs. 16.4 kN 16.4 kN 16.4 kN
WeigHt LBs. kg 14.3 31.0 60.0 34 75 28 63 130 6.5 14.3 27.2 15.4 34 12.7 28.6 59
3/8"
1/2"
10,000 lbs. 44.4 kN 10,000 lbs. 44.4 kN 16,000 lbs. 71.1 kN 16,000 lbs. 71.1 kN 16,000 lbs. 71.1 kN
FoR THE 640 PULLER 300' 91 m 600' 182 m 1,200' 365 m (14.3 mm) FoR THE 6001 & 6501 (UT5) PULLER 300' 91 m 600' 182 m (19.1 mm) 1,200' 365 m FoR THE 6800 (UT8) PULLER 300' 91 m 600' 182 m (22.2 mm) 1,200' 365 m
6,500 lbs. 28.9 kN 6,500 lbs. 28.9 kN 6,500 lbs. 28.9 kN 8,000 lbs. 35.6 kN 8,000 lbs. 35.6 kN 8,000 lbs. 35.6 kN
26,000 lbs. 115.6 kN 26,000 lbs. 115.6 kN 26,000 lbs. 115.6 kN 32,000 lbs. 142.3 kN 32,000 lbs. 142.3 kN 32,000 lbs. 142.3 kN
This rope does not fit on a rope stand. Use reel jacks and a spindle to dispense. See pages 376-377
= ReplacemenT paRT
= accessoRy
171
Canada Tel: 800.435.0786 Fax: 800.524.2853 International Tel: +1.815.397.7070 Fax: +1.815.397.9247
www.greenlee.com
Cable Pulling
aPPLiCatioN
Electrical use. Heavy Duty lubricant adheres well to cable without messy dripping.
Electrical or datacom use. Cleans up quickly, non-staining. Can be applied by hand or pump.
Electrical or datacom use. Will not freeze until 25F. Can be applied by hand or pump.
Pumpable and pourable liquid lubricant for lightweight, fast pulling of fiber optic cables. Cleans up easily.
pplication Temperature Range (F) A pplication Temperature Range (C) A Minimum Storage Temperature Base verage Coefficient of Friction* A Color CoMPatiBiLity (Cable type) ubber R eoprene N ylon N VC P igh-density or cross linked polyethylene H ow-density polyethylene L emiconducting jacket S ypalon H
*(IEEE 375-2 test procedure) kinetic coefficient of friction tested at 300 lb/ft sidewall bearing pressure
Q = 0.0015 x L x D
Canada Tel: 800.435.0786 Fax: 800.524.2853 Where: Q = Quantity of cable lubricant to use in gallons L = Length of cable pull in feet D = Diameter of conduit or duct in inches If the following situations apply, consider using additional lubricant: The cable jacket is hard and/or cable is very stiff. The conduit is rough or dirty. There are many bends to pull through. The percentage of conduit filled by the cable is unusually high. The conduit is water filled.
CoNDUit DiaMeter PULL LeNgtH 200' 300' 400' 600' 800' 1000'
= ReplacemenT paRT = accessoRy
1" 0.3 gal. 0.5 gal. 0.6 gal. 0.9 gal. 1.2 gal. 1.5 gal.
2" 0.6 gal. 0.9 gal. 1.2 gal. 1.8 gal. 2.4 gal. 3.0 gal.
3" 0.9 gal. 1.4 gal. 1.8 gal. 2.7 gal. 3.6 gal. 4.5 gal.
4" 1.2 gal. 1.8 gal. 2.4 gal. 3.6 gal. 4.8 gal. 6.0 gal.
172
www.greenlee.com
Clear Lube
Cable Pulling
LISTED
Designed for use within electrical or datacom cable pulls. Clear and colorless for quick, easy clean-up. Environmentally safe, non-hazardous, non-toxic and non-corrosive. Easy to apply either by hand, brush or pump. Polymer base with no silicon additives. Three-year shelf life with no deterioration in lubricant.
Cat. No. CLR-Q CLR-1 CLR-5 UPC No. 10437 10438 10439 DesCriPtioN Clear Lube pulling lubricant, 1 quart (.95 l) Clear Lube pulling lubricant, 1 gallon (3.79 l) Clear Lube pulling lubricant, 5 gallon (18.93 l)
sPeCiFiCatioNs Weight CLR-Q - 2.3 lbs. (1.0 kg) CLR-1 - 7.6 lbs. (3.5 kg) CLR-5 - 44.8 lbs. (20.4 kg) 10,000 - 20,000 CPS 6.0 - 8.0 0.26
LISTED
USA Tel: 800.435.0786 Fax: 800.451.2632 Canada Tel: 800.435.0786 Fax: 800.524.2853
LISTED
DesCriPtioN Cable-Gel one Quart Squeeze Bottle (.95 l) Cable-Gel one Gallon (3.79 l) Cable-Gel 5 Gallons (18.93 l)
173
www.greenlee.com
Cable Pulling
Winter-Gel will not freeze until -25 F (-31 C). Reduces friction for easy pulling. Compatible with all cable nsulation types. i Cleans up quickly and easily. High lubricity. Can be used all year long. Environmentally safe.
Cat. No. WGEL-Q WGEL-1 WGEL-5 UPC No. 35215 35216 35217 DesCriPtioN Winter-Gel Pulling Lube one Quart Squeeze Bottle (.95 l) Winter-Gel Pulling Lube one Gallon (3.79 l) Winter-Gel Pulling Lube 5 Gallons (18.93 l)
sPeCiFiCatioNs Weight WGEL-Q - 2.3 lbs. (1 kg) WGEL-1 - 9 lbs. (4.1 kg) WGEL-5 - 44 lbs. (20 kg) 10,000 - 14,000 CPS 7.0 - 8.0 0.21
174
= ReplacemenT paRT
= accessoRy
DUCt size iNCH mm 2 50.8 2.5 63.5 3 76.2 3.5 88.9 4 102 5 127 6 152
www.greenlee.com
Cable Pulling
Flat steel bristles for maximum cleaning of sand, grit and light o bstructions from duct. Pulling eye on one end and smaller twisted eye on the other end for ailing line allows bi-directional use. t Can be pulled to loosen dried material before using mandrels or spreader swabs.
MiNiMUM DiaMeter iNCH mm 1.87 47.5 2.38 60.5 2.87 72.9 3.38 85.9 3.87 98.3 4.87 123.7 5.87 149.1 MaxiMUM rateD CaPaCity LBs. kN 200 .89 200 .89 200 .89 200 .89 200 .89 200 .89 200 .89
DUCt size iNCH mm 2 50.8 2.5 63.5 3 76.2 3.5 88.9 4 102 5 127 6 152
WeigHt LBs. kg .83 .38 .83 .38 .83 .38 .90 .41 .95 .43 1.15 .52 1.28 .58
Flexible Mandrel
Useful for cleaning out mud, dirt, and light obstacles from ducts before i nstallation of cable. Can be used around tight bends due to convex contacts between disks. Tapered profile allows pulling in either direction. Pulling eyes on both ends. Polyurethane disks do not damage inner walls of duct.
MaxiMUM Disk size iNCH mm 1.88 47.7 2.19 55.6 2.81 71.4 3.25 82.5 3.75 95.3 4.69 119.1 5.81 147.5 MaxiMUM rateD CaPaCity LBs. kN 2330 10.3 2330 10.3 2330 10.3 4800 21.3 4800 21.3 4800 21.3 4800 21.3
DUCt size iNCH mm 2 50.8 2.5 63.5 3 76.2 3.5 88.9 4 102 5 127 6 152
WeigHt LBs. kg 1 .45 1 .45 1.5 .68 3.5 1.59 4.5 2.04 6 2.72 8.5 3.85
Rope-to-Swivel Connectors
Rope-to-swivel connectors connect the cable pulling rope, up to 1" (254 mm) in diameter, to the pulling swivel. Makes connecting the pulling rope and the pulling swivel easier. Connectors feature a removable sheave for rope eye. Select the connector with a maximum rated capacity that meets or xceeds the cable pullers maximum pulling force. e
Cat. No. 39905 39904 39903 39902 Cat. No. 39849 39850
UPC No. 39905 39904 39903 39902 UPC No. 39849 39850
Max. rateD. CaPaCity iN CoNDUit LBs. kN 5,000 22.2 7,000 31.1 10,000 44.4 10,000 44.4 DesCriPtioN Sheave Sheave Pin
Max. rateD CaPaCity oVerHeaD LBs. kN 3,000 13.3 4,200 18.6 6,000 26.6 6,000 26.6
LeNgtH iN. mm 4-11/16 119 4-11/16 119 4-11/16 119 4-11/16 119
iN. 1/2
e mm 12.7 14.3
iN.
F mm 12.7 15.9
11/16 17.5
11/16 17.5
"E" E
= ReplacemenT paRT
= accessoRy
"F" F
175
www.greenlee.com
Swivels
Cable Pulling
B E A
Helps eliminate winding and tangling of rope and cable during pull. Connects grip and pulling rope. All stainless steel body construction. Efficient thrust and roller bearing construction allows smooth rotation, even under full load. Clevis pins are shoulder bolt style, so load on both sides of clevis is taken on the shoulder, not on the thread. Select the swivel with a maximum rated capacity that meets or exceeds the cable pullers maximum pulling force.
C D mm iNCH F DiaMeter mm iNCH mm iNCH mm e g iNCH WeigHt rePLaCeMeNt * PiN kit mm LBs. kg UPC No.
a DiaMeter iNCH mm
B iNCH mm iNCH
.4 .16 1.0 .45 1.0 .45 2.0 .91 4.0 1.81 7.0 3.18
Breakaway Swivels
BreakaWay PiN kits Cat. No. 9294 3 9295 3 9296 3 9297 3 9302 3 9303 3 9304 3 9306 3 9308 3 UPC No. 39294 39295 39296 39297 39302 39303 39304 39306 39308 BreakiNg PoiNt LBs. 200 lbs. 400 lbs. 600 lbs. 675 lbs. 200 lbs. 400 lbs. 600 lbs. 800 lbs. 1000 lbs. BreakiNg PoiNt kN 0.9 kN 1.8 kN 2.7 kN 3.0 kN 0.9 kN 1.8 kN 2.7 kN 3.6 kN 4.4 kN CoLor CoDe WHITE YELLoW oRANGE BLACK WHITE YELLoW oRANGE GREY RED Use WitH 39290 5/8 Swivel
D C F E B A
Acts as a mechanical fuse, breaking away at a preset load to prevent damage to expensive cable. Breakaway pins can be replaced to change breakaway values.
BreakaWay sWiVeL BoDy oNLy a B C D e F Cat. No. UPC No. iNCH mm iNCH mm iNCH mm iNCH mm iNCH mm iNCH mm 9290 39290 3 5/8 15.9 3-7/32 81.8 9/32 7.1 2-23/32 69.1 7/16 11.1 1/4 6.4 9298 39298 3 7/8 22.2 4-7/32 107.2 3/8 9.5 3-11/32 84.9 17/32 13.5 5/16 7.9
Pins sold in bags of 10 only. Breakaway values are 15%.
Rope Clevis
For forged eye grips For forged eye grips
Removable bolt and rope sheave. Removable grip eye bolt. Select the clevis with a rating that meets or exceeds the cable pullers maximum pulling force. Removable sheave for rope eye.
Cat. No. UPC No. 31910 31905 19524 DesCriPtioN Rope Clevis Rope Clevis Rope Clevis
578
579
578 579 678 sPeCiFiCatioNs Maximum rated Capacity 578 6,500 lbs. (28.9 kN) 579 10,000 lbs. (44.4 kN) 678 6,500 lbs. (28.9 kN)
678
176
Weight 0.9 lbs. (408 g) 1.3 lbs. (589 g) 1.3 lbs. (589 g)
Length 3.0" (76 mm) 3.5" (89 mm) 3.5" (89 mm)
Width 1.406" (36 mm) 1.84" (47 mm) 1.75" (44 mm)
inside Diameter 1.25" (32 mm) 1.5" (38 mm) 0.94" (24 mm)
= ReplacemenT paRT
= accessoRy
www.greenlee.com
GRIPS
Cable Pulling
624L
DesCriPtioN Set Screw Clamp-Type Pulling Grip Pulling Grip with Clevis includes 624S, 624L and 678 clevis - 4 clamp Pulling Grip includes 624S and 624L - 2 clamp each Short Pulling Grip - 2 Clamp Long Pulling Grip - 2 Clamp Grip Allen Wrench Grip Set Screw (2 per clamp), 629 and 624 - 8 for each grip 624L and 624S - 4 for each grip.
624S
sPeCiFiCatioNs Maximum rated Capacity 540 6,500 lbs. (28.9 kN) 629 6,500 lbs. (28.9 kN) 624 6,500 lbs. (28.9 kN) 624S 3,250 lbs. (14.5 kN) 624L 3,250 lbs. (14.5 kN) sPeCiFiCatioNs Capacity Weight size 1,750 lbs. (7.7 kN) 1.2 lbs. (.5 kg) Receptacle - 5/8" (15.9 mm) Weight 540 5 lbs. (2.3 kg) 629 5 lbs. (2.3 kg) 624 3.5 lbs. (1.5 kg) 624S 2 lbs. (.9 kg) 624L 2.1 lbs. (1 kg)
Each grip has two opposed set screws that provide positive locking. openings in wire grip should be 50% filled with wire to assure slip-proof grip.
= ReplacemenT paRT
= accessoRy
177
www.greenlee.com
Cable Pulling
griP tyPe Junior Grips Light Duty Grips T-Type Grips K-Type Grips
DesCriPtioN Single weave galvanized steel mesh Single weave galvanized steel mesh Double weave galvanized steel mesh Double weave galvanized steel mesh
Multiple Strength Triple to double to single weave Grips galvanized steel mesh Slack Grips Rod Closing Double weave galvanized steel mesh rod closing offset eye
2. seLeCt tHe size oF griP NeeDeD. After determining the type of grip needed, measure the diameter of the cable being pulled. If pulling more than one cable of the same diameter, refer to chart below for required grip diameter range. If pulling more than one cable of different diameters, bundle cables together, measure the circumference CaBLes WitH tHe saMe DiaMeter iN oNe griP*
2 CaBLes Dia. eaCH iN./(mm) .30-.38/(7.6-9.7) .38-.44/(9.7-11.2) .44-.59/(11.2-15.0) .59-.75/(15.0-19.1) .75-.90/(19.1-22.9) .90-1.07/(22.9-27.2) 1.07-1.22/(27.2-31.0) 1.22-1.53/(31.0-39.9) 1.83-2.14/(46.5-54.4) 2.44-2.75/(62.0-69.9) 2.75-3.06/(69.9-77.7) 3 CaBLes Dia. eaCH iN./(mm) .25-.31/(6.4-7.9) .31-.36/(7.9-9.1) .36-.49/(9.1-12.4) .49-.63/(12.4-16.0) .63-.76/(16.0-19.3) .76-.89/(19.3-22.6) .89-1.02/(22.6-25.9) 1.02-1.28/(25.9-32.5) 1.53-1.79/(38.9-45.5) 2.05-2.30/(52.0-58.4) 2.30-2.56/(58.4-65.0) 4 CaBLes Dia. eaCH iN./(mm) .22-.27/(5.6-6.9) .27-.31/(6.9-7.9) .31-.42/(7.9-10.7) .42-.54/(10.7-13.7) .54-.65/(13.7-16.5) .65-.77/(16.5-19.6) .77-.88/(19.6-22.4) .88-1.10/(22.4-27.9) 1.10-1.32/(27.9-33.5) 1.32-1.54/(33.5-39.1) 1.54-1.76/(39.1-44.7) 1.76-1.98/(44.7-50.3) 1.98-2.20/(50.3-55.9) 5 CaBLes Dia. eaCH iN./(mm) .19-.24 /(4.8-6.1) .24-.29/(6.1-7.4) .29-.38/(7.4-9.7) .38-.48/(9.7-12.2) .48-.58/(12.2-14.7) .58-.67/(14.7-17.0) .67-.77/(17.0-19.6) .77-.96/(19.6-24.2) .96-1.16/(24.2-29.5)
and refer to the chart on bottom of this page for required grip diameter range. once the cable diameter or equired grip diameter is determined, refer to r individual chart for type of grip chosen to locate Catalog/UPC number.
6 & 7 CaBLes Dia. eaCH iN./(mm) .17-.22/(4.3-5.6) .22-.26/(5.6-6.6) .26-.34/(6.6-8.6) .34-.43/(8.6-10.9) .43-.52/(10.9-13.2) .52-.60/(13.2-15.2) .60-.69/(15.2-17.5) .69-.86/(17.5-21.8) .86-1.03/(21.8-26.2)
8 CaBLes Dia. eaCH iN./(mm) .15-.19/(3.8-6.1) .19-.23/(6.1-5.8) .23-.31/(5.8-7.9) .31-.39/(7.9-9.9) .39-.46/(9.9-11.7) .46-.54/(11.7-13.7) .54-.62/(13.7-15.7) .62-.77/(15.7-19.6) .77-.93/(19.6-23.6)
9 CaBLes Dia. eaCH iN./(mm) .14-.18/(3.6-4.6) .18-.21/(4.6-5.3) .21-.28/(5.3-7.1) .28-.35/(7.1-8.9) .35-.42/(8.9-10.7) .42-.49/(10.7-12.4) .49-.56/(12.4-14.2) .56-.71/(14.2-18.00) .71-.85/(18.0-21.6) .85-.99/(21.6-25.1)
reQUireD griP DiaMeter iN./(mm) .50-.61/(12.7-15.5) .62-.74/(15.7-18.8) .75-.99/(19.1-25.1) 1.00-1.24/(25.4-31.5) 1.25-1.49/(31.8-37.8) 1.50-1.74/(38.1-44.2) 1.75-1.99/(44.5-50.5) 2.00-2.49/(50.8-63.2) 2.50-2.99/(63.5-75.9) 3.00-3.49/(76.2-88.6) 3.50-3.99/(88.9-101.3)
1.54-1.74/(39.1-44.2) 1.37-1.55/(34.8-39.4) 1.24-1.39/(31.5-35.3) 1.13-1.27/(28.7-32.3) 4.00-4.49/(101.6-114.0) 1.74-1.93/(44.2-49.0) 1.55-1.72/(39.4-43.7) 1.39-1.55/(35.3-39.4) 1.27-1.41/(32.3-35.8) 4.50-4.99/(114.3-126.7)
iNCH
.50- .61 .62- .74 .75- .99 1.00-1.24 1.25-1.49 1.50-1.74 1.75-1.99 2.00-2.49 2.50-2.99 3.00-3.49 3.50-3.99 4.00-4.49 4.50-4.99
mm
12.7- 15.5 15.8- 18.8 19.1- 25.1 25.4- 31.5 31.8- 37.8 38.1- 44.2 44.5- 50.5 50.8- 63.2 63.5- 75.9 76.2- 88.6 88.9-101.3 101.6-114.0 114.3-126.7
1.57- 1.95 1.95- 2.36 2.36- 3.14 3.14- 3.93 3.93- 4.71 4.71- 5.50 5.50- 6.28 6.28- 7.85 7.85- 9.42 9.42-11.00 11.00-12.57 12.57-14.14 14.14-15.71
= accessoRy
178
Note: Rope is a very critical link in the cable pulling system. See page 387 for proper pulling rope selection.
www.greenlee.com
Cable Pulling
Handy set gives you the size range you need. Have the correct grip on the job and save time.
Cat. No. 30758 UPC No. 30758 DesCriPtioN Building Wire Junior Grip Set - diameter range .25" - 1.24" (6.4 - 31.5 mm). Consists of 30588, 30590, 30592, and 30594, 30584, 30586. T-Type Grip Set - diameter range .75" - 1.99" (19 - 50.5 mm). Consists of 30576, 30578, and 31010. T-Type Grip Set - diameter range 1.50' - 2.99" (38.1 - 75.9 mm). Consists of 31010, 30580 and 31012. T-Type Grip Set - diameter range .75' - 2.99" (19 - 75.9 mm). Consists of 30576, 30578, 31010, 30580 and 31012.
sPeCiFiCatioNs Capacity 30758 - (2) #14 to 4-1/0, .25" - 1.24" (6.4 - 31.5 mm) diameter 597 - 3-1/0 to 250 MCM, .75" - 1.99" (1.9 - 50.5 mm) diameter 598 - 3-350 MCM to 3-750 MCM, 1.50" - 2.99" (38.1 - 75.9 mm) diameter 599 - 3-1/0 to 3-750 MCM, .75" - 2.99" (1.9 - 75.9 mm) diameter 30758 - 1.2 lbs. (.5 kg) 597 - 6 lbs. (2.7 kg) 598 - 9.9 lbs. (4.5 kg) 599 - 13 lbs. (5.9 kg)
30758
Weight
= ReplacemenT paRT
= accessoRy
179
USA Tel: 800.435.0786 Fax: 800.451.2632 Canada Tel: 800.435.0786 Fax: 800.524.2853 International Tel: +1.815.397.7070 Fax: +1.815.397.9247
www.greenlee.com
Cable Pulling
Use to pull in: conduit or tray. Type of pulls: light-duty, short, easy runs. Type of grip: single weave galvanized steel mesh with flexible pulling eye. Select the grip with a maximum rated capacity that meets or exceeds the cable pullers maximum pulling force.
CaBLe DiaMeter raNge Cat. No. 0536 3 0538 3 0540 3 0542 3 0544 3 0546 3 0548 3 0550 3 0552 3 0554 3 UPC No. staNDarD 30536 30538 30540 30542 30544 30546 30548 30550 30552 30554 .50 - .61 .62 - .74 .75 - .99 1.00 - 1.24 1.25 - 1.49 1.50 - 1.99 2.00 - 2.49 2.50 - 2.99 3.00 - 3.49 3.50 - 3.99 12.7 - 15.5 15.6 - 18.9 19.0 - 25.3 25.4 - 31.5 31.6 - 38 38.1 - 50.7 50.8 - 63.4 63.5 - 76.1 76.2 - 88.8 88.9 - 101.3 560 560 800 1360 1360 1360 1700 2120 2940 2940 2.5 2.5 3.5 6 6 6 7.5 9.4 13 13 5 5 6 7 7 8 9 9 10 10 127 127 152.4 177.8 177.8 203.2 228.6 228.6 254 254 16 16 20 20 21 23 25 27 30 32 406.4 406.4 508 508 533.4 584.2 635 685.8 762 812.8 iNCH mm MaxiMUM rateD CaPaCity LBs. kN eye LeNgtH iNCH mm iNCH MesH LeNgtH mm
180
= ReplacemenT paRT
= accessoRy
Note: Rope is a very critical link in the cable pulling system. See page 387 for proper pulling rope selection.
www.greenlee.com
Cable Pulling
Use to pull in: conduit or tray. Type of pulls: heavy-duty, long, hard runs. Type of grip: double-weave galvanized steel mesh with flexible pulling eye. Select the grip with a maximum rated capacity that meets or exceeds the cable puller's maximum pulling force.
CaBLe DiaMeter raNge Cat. No. 30442 30998 30460 31000 30462 31002 30464 31004 30466 31006 30468 30470 UPC No. staNDarD 30442 30998 30460 31000 30462 31002 30464 31004 30466 31006 30468 30470 .50 - .61 .62 - .74 .75 - .99 1.00 - 1.49 1.50 - 1.99 2.00 - 2.49 2.50 - 2.99 3.00 - 3.49 3.50 - 3.99 4.00 - 4.49 4.50 - 4.99 5.00 - 5.99 12.7 - 15.5 15.6 - 18.9 19.0 - 25.3 25.4 - 38.0 38.1 - 50.7 50.8 - 63.3 63.5 - 76.1 76.2 - 88.8 88.9 - 101.5 101.6 - 114.2 114.3 - 126 127 - 152.3 1120 1360 1920 3280 3280 5440 6600 8200 9600 9600 9600 9600 4.9 6 8.5 14.5 14.5 24.1 29.3 36.5 42.7 42.7 42.7 42.7 5 5 6 7 7 9 10 10 10 10 10 10 127 127 152.4 177.8 177.8 228.6 254 254 254 254 254 254 16 16 32 33 34 36 38 39 41 42 58 60 406.4 406.4 812.8 838.2 863.6 914.4 965.2 990.6 1041.4 1066.8 1473.2 1524 7/8 7/8 1 1-3/8 1-3/8 1-5/8 1-7/8 1-7/8 1-7/8 1-7/8 1-7/8 1-7/8 22.2 22.2 25.4 34.9 34.9 41.2 47.6 47.6 47.6 47.6 47.6 47.6 iNCH mm MaxiMUM rateD CaPaCity LBs. kN eye LeNgtH iNCH mm MesH LeNgtH iNCH mm rotatiNg eye Dia. iNCH mm
= ReplacemenT paRT
= accessoRy
Note: Rope is a very critical link in the cable pulling system. See page 387 for proper pulling rope selection.
181
USA Tel: 800.435.0786 Fax: 800.451.2632 Canada Tel: 800.435.0786 Fax: 800.524.2853 International Tel: +1.815.397.7070 Fax: +1.815.397.9247
www.greenlee.com
Cable Pulling
Use to pull when the end of the conductor is not available. Type of pulls: light and straight. The rod will not flex around bends. Single weave galvanized steel mesh with rod closing and an offset flexible eye. Select the grip with a maximum rated capacity that meets or exceeds the cable pullers maximum pulling force.
CaBLe DiaMeter raNge iNCH mm .50 - .61 12.7 - 15.50 .62 - .74 15.6 - 18.9 .75 - .99 19 - 25.3 1.00 - 1.24 25.4 - 31.5 1.25 - 1.49 31.6 - 38.0 1.50 - 1.74 38.1 - 44.3 1.75 - 1.99 44.4 - 50.7 2.00 - 2.49 50.8 - 63.4 2.50 - 2.99 63.5 - 76.1 3.00 - 3.49 76.2 - 88.8 3.50 - 3.99 88.9 -101.3 MaxiMUM rateD CaPaCity LBs. kN 300 1.3 360 1.6 440 1.9 680 3 900 4 1160 5.1 1520 6.7 1800 8 2200 9.7 2400 10.6 2400 10.6 eye LeNgtH iNCH mm 7 177.8 7 177.8 7 177.8 8 203.2 8 203.2 9 228.6 10 254 10 254 10 254 12 304.8 12 304.8 MesH LeNgtH iNCH mm 6 152.4 8 203.2 10 254 12 304.8 14 355.6 15 381 16 406.4 19 482.6 20 508 21 533.4 24 610
Cat. No. 0658 3 1024 3 0660 3 1026 3 0662 3 1028 3 0664 3 1030 3 0666 3 1032 3 0668 3
UPC No. 30658 31024 30660 31026 30662 31028 30664 31030 30666 31032 30668
Note: Rope is a very critical link in the cable pulling system. See page 387 for proper pulling rope selection.
182
= ReplacemenT paRT
= accessoRy