Beruflich Dokumente
Kultur Dokumente
Experiment 4
Extracting of copper sulfate from sand by using water solvent in liquid-solid extraction
Done by: Ahmed sameer, 20073435 Supervised by: Dr. Fatma Marhoon
Semester I, 2011-2012
Abstract
Copper sulfate was extracted from sand in liquid-solid extraction process by using water solvent. The water is evaporated and then condensed to ensure its purity. The concentration of copper sulfate was determined by using ultraviolet spectrometer. The amount of copper sulfate before extraction was chosen to be 7 grams and the amount determined before extraction was founded to be 6.153 grams with recovery yields equal to 87.91%. The
error between experimental value and the ideal value was founded to be 12.08% which can be considered as acceptable value. However the amount of extracted copper sulfate can be increased by using higher selectivity solvent and by added agitator to increase its solubility.
|Page2
Table of Contents
Abstract ...................................................................................................................... 2 I.Introduction and Background ....................................................................................... 4 II.Theory ...................................................................................................................... 5 III.Industrial Applications ............................................................................................... 6 IV.Apparatus and Procedures ......................................................................................... 7 IV.1 Apparatus .......................................................................................................... 7 IV.2 Material .......................................................................................................... 7 IV.3 Procedure .......................................................................................................... 7 V.Results and disscusion ................................................................................................ 8 VI.Conclusions and Recommendations ............................................................................ 9 VII.References ............................................................................................................ 01 VIII.Appendices .......................................................................................................... 00 A. Raw Data............................................................................................................ 00 B. Sample Calculations ............................................................................................. 01 C. Nomenclature ..................................................................................................... 02
|Page3
|Page4
II. Theory
When a liquid solvent is added to a mixture of solids, the solid which have a high solubility in the solvent will be separated from the other solid as shown in figure 2-1. The mechanism of solid liquid extraction is:
1- The solvent diffuses into the solid phase 2- The diffused solvent dissolves the solutes and transfer it to liquid phase
Since the solution layer which contain the solvent and the extracted solid have less density than the other layer it will be formed at the top. Then the two layers can be separated by gravity or vacuum filtration Leaching is always followed by solvent recovery, which involves another mass transfer operation; such as filtration.
Figure 2-1: mechanism of solid-liquid extraction The separation process is not ideal and part of the solid will not dissolved in the solvent. The performance of solid-liquid extraction process is expressed in term of yield recovery which is the ratio between the amount of extracted solid and the original amount of solid before extraction take place. For extracted solid, the yield recovery is written as:
( )
) Equation (2-1)
Where R is the yield recovery, M is the molecular weight of, C is the concentration, is the final volume of the solution, m is mass of solids mixture and F is the weight percent of extracted solid in the original solids mixture. [2] The error can be calculated from the deviation of ideal value:
( ) ( )
) Equation (2-2)
The concentration of the extracted solid can be determined by using different techniques. One of these techniques is using ultraviolet spectrometer instrument. A light will pass through the solution and part of it will be absorbed. According to the Beer-Lambert law , the absorbance of a solution is directly proportional to the concentration of the absorbing species in the solution and the path length. By determining the absorbance of the solution and using calibration curve the concentration can be calculated. [3] |Page5
III.
Industrial Applications
Heap leaching
Heap leaching is an industrial process for extracting precious metals and minerals by dissolving them from ore with liquids. The process is commonly used to extract metals such as gold, copper, and uranium yellowcake in addition to several other minerals. Heap leaching is usually carried out in the open and on slightly sloping ground covered with a watertight plastic sheet or clay layer onto which a heap of crushed ore is placed. The heap is sprayed with the leaching solution which percolates or flows down through it and dissolving and carrying away the metals as it goes. The solution is then collected, sent to a processing plant for treatment to separate the valuable elements, reconditioned, and sent back to the heap for another cycle (see figure 3-1). [4]
Other applications:
1- Removal of sugar from sugar beets using water as the solvent. 2- Medicine industry.
|Page6
IV.
IV.1 Apparatus
The liquid-solid extractor unit consists of an electrical heater and a condenser which they used to evaporate and condense the solvent to make it pure. A temperature controlling system used to control the temperature in the heater and condenser. The extraction process takes place in the extractor vessel where the solids mixture placed inside and water droplets fall from the condenser (see figure 4-1). [5]
IV.2 material
In this experiment the solute is copper sulfate solvent is water , the insoluble solid is sand and the
IV.3 Procedure
1- Prepare a solid mixture contain 8 gram of CuSO4 and sand. 2- Place the mixture inside the extractor vessel. 3- Set the water temperature to 100 Celsius (evaporation temperature) and wait until the temperature readings reach the set point, it may take 2 hours. 4- The extraction process will take place and the color will change to be blue. 5- Close the water flow and stop the extraction process when the vessel becomes full. 6- Use UV spectrometer to determine the concentration of copper sulfate.
Condenser
Solid mixtures
|Page7
0.038552
6.153
0.847
87.91
12.08
The amount of copper sulfate in the solids mixture was chosen to be 7 grams. The concentration of extracted solid was determined by UV spectrometer to be 0.038552 mol/L. the amount of extracted solid was determined to be 6.153 grams and the amount solids which was not recovered is 0.847 grams. The recovery yield which is calculated by using equation (2-1) is 87.91%. The error between extracted value and ideal value is 12.08%. The error is acceptable since most of the copper sulfate is extracted. Source of error in this experiment may from the fitted calibration curve and the Wight of the solid mixture.
|Page8
VI.
To conclude, copper sulfate was extracted by water solvent from sand. The recovery yields were founded to be 87.91% and the amount of extracted solid was founded to be 6.153 grams. The experiment was very helpful and we learned about two units, the extraction unit and UV spectrometer unit. The amount of extracted solid can be increased by using high selectivity solvent if its available. Adding agitator to the extraction unit may increase the solubility of copper sulfate in the solvent. Using more accurate balance may decrease the results error.
|Page9
VII.
References
1- Wikipedia leaching chemistry http://en.wikipedia.org/wiki/Leaching_(chemistry) 2- J. D. Seader, Ernest J. Henley, "Separation Process Principles 2nd Edition" W iley | 2005 3- Wikipedia ultraviolet http://en.wikipedia.org/wiki/Ultraviolet%E2%80%93visible_spectroscopy 4- wisegeek what is heap leaching http://www.wisegeek.com/what-is-heapleaching.htm 5- The laboratory manual which is handled by the instructure.
| P a g e 10
VIII. Appendices
A. Raw Data
Before extraction: weight of the copper sulfate = 7 g After extraction: volume = 1 L, Absorbance = 0.401 A Molecular weight of copper sulfate= 159.62 g/mol
Table A-1: UV spectrometer calibration curve data Con. (M) 0.18 0.144 0.108 0.054 0.036 0.018 0.0098 abs. (A) 1.989 1.487 1.125 0.555 0.353 0.234 0.094
Concentration vs Abs
0.2 0.18 0.16 0.14 0.12 0.1 0.08 0.06 0.04 0.02 0 0 0.5 1 1.5 2 Absorbance (A) y = 0.0924x + 0.0015 R = 0.9965
Concentration (M)
2.5
| P a g e 11
B. Sample Calculations
The relationship between the absorbance and the concentration from linear curve fitting as shown in figure A-1 is:
( )( ( )
| P a g e 12
c. nomenclature
R: C: M: F: Vf : recovery yield concentration of extracted solid mass of solids mixture fraction in weight of solute in the mixture final volume of the solution
| P a g e 13