Beruflich Dokumente
Kultur Dokumente
I. Introduction
A. General Information
Read and understand all labels, MSDS, and this instruction manual before use. The Industrial - Remote Reservoir Parts Cleaner is an economical, safe, and innovative system designed to clean parts, using a mineral spirits based solvent. This parts cleaner incorporates a " Remote Reservoir " design, which limits the loss of solvent through evaporation and also provides an additional fire safety feature. Many fire jurisdictions promote use of equipment incorporating this design feature. Check with your local fire jurisdiction for additional information. Install your parts cleaner on a flat level surface in an area provided with adequate ventilation. Avoid repeated or prolonged breathing of vapors. Use of compressed air to dry parts may cause a high concentration of vapors in the immediate area. Local exhaust ventilation should be used in areas of high vapor concentration. Provisions for determining and maintaining adequate ventilation are the responsibility of the operator. Do not allow the parts cleaner to operate unattended. Make sure the parts cleaner is connected to a properly grounded 110 volt, 60 HZ. electrical power source. This equipment is designed for use with mineral spirits based solvents with a flash point greater than 60C. (140F.). Use only mineral spirits based solvents. Do not use Flammable solvents. Do not add any other chemicals to the cleaning solvent including, but not limited to, kerosene, fuel oil, gasoline, chlorinated solvents, or detergents. The use of any other solvents could potentially cause a hazardous condition. Under certain conditions the solvent could burn. For your protection, a fusible link automatically closes the cover of the parts cleaner in the event that a fire occurs in the sink work area. The closed cover contains and smothers the fire inside the metal sink. Do not leave large objects in the parts cleaner or hang anything on the cover that could prevent it from closing in the event of a fire. Do not replace fusible link with any other device to hold cover up. Do not place heavy objects on edges or front of sink. Although this parts cleaner is designed to be stable, uneven weight distribution could cause a hazardous condition, over which the manufacturer has no control. Do not block drain or modify the equipment in any way. 1
7578
In case of a fire:
Use a Type ABC or Type BC fire extinguisher. Do not use water. Contact your local fire department.
C. Environmental
1. Avoid spilling solvent. If solvent is spilled, clean it up immediately. Consult Material Safety Data Sheet for instructions on clean up and disposal. 2. Contain leaks promptly. Notify local environmental authorities if necessary. 3. Proper housekeeping in the area of the parts cleaner is the responsibility of the user. 4. Check with your local jurisdiction for any other applicable hazardous materials compliance requirements. 5. Do not remove devices designed to reduce solvent evaporation except to process work or to perform maintenance. This parts cleaner incorporates a " Remote Reservoir " design, which limits the loss of solvent through evaporation and also provides an additional fire safety feature. 6. For further information consult the Material Safety Data Sheet provided by the solvent supplier. 3
7578
III. Installation
A. Position the drum on a hard level surface in a well-ventilated area. B. Unpack the parts. C. Place the sink on its side. D. Hook the pump assembly to the bracket on the bottom side of the tank. E. Feed the pump cord through the large hole in the pump plate on the back of the machine, and snap the cord cover in the hole. F. Feed the hose from the pump through hole in the pump plate on the back of the machine, and attach to the hose-barb on the back of the sink. Secure with a hose clamp. G. Place the sink onto the drum. H. Place the strainer and grate in the drain hole in the bottom of the sink. I. Place the control box in the bracket on the right side of the machine. J. Using the screw and star-washer, fasten the control box to the control box bracket. K. Plug the pump cord and light cord (if equipped) into the receptacle on control box. L. Plug the power cord into a 115VAC/60HZ/15amp grounded receptacle. M. Fill solvent reservoir to the correct level as indicated by the table below. Use only mineral spirits based solvents with a flash point greater than 60C. (140F.). 1. Capacity Model E-216 = 37.9 L. (10 gal.). 2. Capacity Model E-230 = 75.7 L. (20 gal.).
4
7578
5
7578
6
7578
7
7578