Beruflich Dokumente
Kultur Dokumente
BARRELS
.223 CAL. SST BARRELS
20 SST DCM BARREL, PRE BAN
.223 Cal., 1x8 Twist Includes Adjustable Front Sight Post
BL-DCM
Retail . . . .$199.00
BL-DC-F
Retail . . . .$199.00
BL-SASS
Retail . . . .$239.95
ACCESSORIES-BARRELS
BL-DC
Retail . . . .$179.00
BL-M12
Retail . . . .$179.00
BL-10
Retail . . . .$179.00
BULL-03-16
Retail . . . .$239.00
20 1x9 TWIST, POST BAN 20 BULL BARREL W/SINGLE RAIL GAS BLOCK
Now with a Koelbl Single Rail Gas Block! Target Crowned Muzzle No Bayonet Lug 5.56 x 45mm
BL-10P
Retail . . . .$179.00
BULL-03
Retail . . . .$259.00
16 1x9 TWIST
20 barrel sight radius Uses standard A2 handguards 5.56 x 45mm, 1x9 Twist
BL-10-A
Retail . . . .$180.00
Retail . . . .$289.00
Carbine barrel sight radius Uses carbine handguards 5.56 x 45mm, 1x9 Twist
BL-11
Retail . . . .$170.00
50
BL-10-AP
Retail . . . .$180.00
BL-11-AP4
Retail . . . .$189.00
BL-12
Retail . . . .$185.00
BL-AP4
Retail . . . .$204.00
ACCESSORIES-BARRELS
BL-AP4PMC
Retail . .$229.95
BL-14H
Retail . . . .$185.00
BL-11P
BL-14H-PF
Retail . . . .$212.00
BL-L16
Retail . . . .$169.00
BL-12B
Retail . . . .$185.00
BL-L16P
Retail . . .$169.00
BL-12A
Retail . . . .$185.00
Barrel Information
To achieve the best results for accuracy you should clean the chamber and bore after every round for the first 25 rounds, then every 10 rounds up to 100 rounds. It usually takes about 200 rounds per barrel for optimum accuracy. Please keep in mind that our barrels are production barrels, not custom barrels. Accuracy is dependent upon many factors such as bullet weight, powder load, rifling twist, rifling lands, operator technique, etc. Our production barrels have achieved anywhere from 1/8" to 1 1/2" M.O.A.. Obviously, we would hope that every production barrel would shoot 1/2" M.O.A., but with all of the above factors, we cannot guarantee a specific group size. NOTE: Using reloaded ammunition will void warranty. Modifying chamber or barrel voids warranty. This includes re-reaming of chamber, re-turning barrel to a lesser diameter and/or re-threading barrel for compensator or attachments.
51
WF-SP-5
WF-SP-53
BT-02SA
Retail . . . . .$82.95
BT-02S
Retail . . . . .$60.00
WF-SP-510
ACCESSORIES-RECEIVERS
6.8mm EXTRACTOR
BT-68E Retail . . . . .$23.95
7.62 x 39 EXTRACTOR
BT-762E Retail . . . . .$18.95
Bolt Assembly, assembled 6.8mm SPC Bolt Assembly, assembled 7.62 x 39mm Bolt Stripped
Conversion or replacement parts for the 6.8mm SPC caliber. Will not work with .223.
.308 A3-STYLE UPPER SOLID STEEL FLATTOP RECEIVER, ASSEMBLED UPPER RECEIVER, .308
308-FTT-EA1 Retail . . . .$209.95
308-FTT-EA1 SHOWN Extra thick walled, extruded from 6066-T6 aluminum Low style flattop allows use of detachable carry handle. 308-FTT-EA1 includes the charging handle, ejection cover assembly & forward assist. Cannot Be Used On The LR-30S Rifle!
Includes one (1) each of the following parts: 308-BT-14 Firing Pin, AR 308-BT-07 Extractor Machined from 4140 steel for increased 308-BT-16 Firing Pin Retaining Pin hardness and wear resistance. 308-BT-03 Extractor Pin Balanced, smoother, sleeker and more rigid 308-BT-05 Ejector Spring alternative to the standard .308 upper 308-BT-08 Extractor Spring receiver. Assembly Adds stability and increases accuracy by 308-BT-06 Ejector bringing the rifles center of balance closer to 308-BT-04 Ejector Roll Pin the shooters body. 308-BT-17 Cam Pin Cannot Be Used On The LR-30S Rifle! And three (3) of the following parts: 308-FTT-LPS Retail . . . .$300.00 308-BT-01 Bolt Gas Rings
Lightweight version of the DPMS A3 Upper Receiver. Cannot Be Used On The LR-30S Rifle!
Carry handle designed to attach to 308 AR Flattop upper receivers allows use of iron sights. Easily installed and removed. Machined from 6061-T6 aluminum bar stock.
The pointed end of this chamber flag can be used as a Delrin Punch. The recessed area in the front of the flag holds an A2 Sight Tool (sold separately). A hole punched in the bottom of the flag allows you to secure an A2 Sight Tool with cable or string (not included). A rounded tab at the top can be used as a scope adjustment tool (no need to carry coins). This chamber flag is included with all DPMS LR-308 rifle purchases.
52
UPPER RECEIVERS
UPPER RECEIVERS & ASSEMBLIES
A3 FLATTOP, STRIPPED
FTT-EA Retail . . . .$125.00
STRIPPED
A3 FLATTOP, ASSEMBLED
FTT-EA1 Retail . . . .$165.00
COMPLETE ASSEMBLY
ACCESSORIES-RECEIVERS
Low style flattop allows use of detachable carry handle. Used by the military Stripped A3 does not include the charging handle, ejection cover or forward assist assy. FTT-EA1 includes the charging handle, ejection port cover assembly & forward assist.
DPMS unveils the Lo-Pro-style 3-Rail upper receiver, an AR receiver that provides three additional mounting options. Machined from a 6066-T6 extrusion, this upper receiver is hardcoat anodized per Mil Spec and Teflon coated a matte black. The upper receiver features a standard Picatinny top rail with 15 slots, but making this AR receiver unique is the additional rails featured on the left and right sides. These two sides rails, located 22.5 degrees from horizontal, provide additional slots for mounting a variety of accessories. The left-hand rail features 15 slots while the right-hand rail provides an additional six. 3-Gunners and tactical shooters alike will appreciate the ability to mount back-up ironsights should their optic ever fail. The Lo-Pro-style 3-Rail Upper Receiver from DPMS will make the age-old problem of not having enough rails for accessories obsolete. Great for 3-Gun Competition!
FLATTOP LO-PRO
FTT-LP Retail . . . .$125.00
HI-RIDER FLATTOP
FTT-HR Retail . . . .$125.00
TRI-MOUNT FLATTOP
FTT-01
FTT-01
Retail . . . .$159.00
Retail . . . . . .$159.00
FTT-HRA
Dust cover omitted for lightweight, smooth, snag-free function Rail height slightly higher than A3 upper State-of-the-art aluminum material Picatinny Rail No forward assist or ejection cover
Retail . . . .$139.95
FTT-02
Retail . . . .$197.95
Dust cover omitted for lightweight, smooth, snag-free function Rail height approximately 1 7/8 above bore center line State-of-the-art aluminum material Picatinny Rail No forward assist or ejection port cover FTT-HRA includes the charging handle
Raise the optical axis of your AR without loss of rigidity, plus add the ability to mount additional accessories on the two lower Weaver rails with standard one inch rings. FTT-02 is assembled with charging handle, forward assist & ejection port cover assembly.
A solid integral two-piece extension of the upper receiver that allows operators to install a wider variety of optical accessories with greater security and stability. The extended rail can support multiple simultaneous attachments such as the red dot reflex sight and your night vision system or forward mounted reflex sight.
A2 UPPER
A1 UPPER
UR-36
UR-01-E3
Retail . . . .$134.95
URPK-1 Shown
UR-01-E3 Shown
UR-01-A3B
Retail . . . .$219.00
Retail . . . . . .$199.99
Carry handle designed to attach to AR Flattop upper receivers allows use of iron sights. Easily installed and removed. Made from 7075 forged aluminum.
A2 sight assembly, windage and elevation adjustable Shell deflector, dust cover and forward assist UR-01-A3B is assembled with charging handle, forward assist & ejection port cover assembly. UR-01-A3B is shown.
Both Include: (1) Forward Assist Assembly (1) Ejection Cover Assembly (1) A2 Rear Sight Assembly
A1 style fixed carry handle Forged from 7075 aluminum that has been T6 heat treated, hard coat anodized (Mil-A-8625A) and Teflon coated black UR-A1 is ASSEMBLED with the charging handle, shell deflector, dust cover, teardrop forward assist and A1 sight assembly (windage only). UR-01-E3 SHOWN!
53
UPPER RECEIVERS
UPPER RECEIVERS FROM VLTOR
MUR A3 W/BOLT ASSIST & SHELL DEFLECTOR
UR-MUR-1A Retail . . . .$229.95
VIS W/BOLT ASSIST & VIS W/SHELL SHELL DEFLECTOR (CAR) DEFLECTOR ONLY (CAR)
FF-VIS-1AK Retail . . . .$629.95 FF-VIS-1SK Retail . . . .$595.95
ACCESSORIES-RECEIVERS
The MUR is a rigid MilSpec flat-top upper receiver made to fit all AR15/M16/M4 rifles and carbines. The MUR was developed to give the customer a MilSpec correct upper receiver with a thicker wall making the MUR upper receiver a more rigid platform. With bolt assist and shell deflector.
The MUR is a rigid MilSpec flat-top upper receiver made to fit all AR15/M16/M4 rifles and carbines. The MUR was developed to give the customer a MilSpec correct upper receiver with a thicker wall making the MUR upper receiver a more rigid platform. With shell deflector only.
The CARBINE LENGTH Versatile Interface Structure (VIS) upper receiver assembly. The VIS is a polylithic upper receiver assembly that ties the normally individual receiver and handguard into an aggregate single part. Includes bolt assist and shell deflector.
The CARBINE LENGTH Versatile Interface Structure (VIS) upper receiver assembly. The VIS is a polylithic upper receiver assembly that ties the normally individual receiver and handguard into an aggregate single part. Includes shell deflector only.
VIS W/SHELL VIS W/BOLT ASSIST & SHELL DEFLECTOR (MID) DEFLECTOR ONLY (MID)
FF-VIS-2AK Retail . . . . .$674.95 FF-VIS-2SK Retail . . . .$649.95
VIS W/SHELL VIS W/BOLT ASSIST & SHELL DEFLECTOR (STD) DEFLECTOR ONLY (STD)
FF-VIS-3AK Retail . . . .$729.95 FF-VIS-3SK Retail . . . .$695.95
The MID LENGTH Versatile Interface Structure (VIS) upper receiver assembly. The VIS is a polylithic upper receiver assembly that ties the normally individual receiver and handguard into an aggregate single part. Includes bolt assist and shell deflector.
The MID LENGTH Versatile Interface Structure (VIS) upper receiver assembly. The VIS is a polylithic upper receiver assembly that ties the normally individual receiver and handguard into an aggregate single part. Includes shell deflector only.
The STANDARD LENGTH Versatile Interface Structure (VIS) upper receiver assembly. The VIS is a polylithic upper receiver assembly that ties the normally individual receiver and handguard into an aggregate single part. Includes bolt assist and shell deflector.
The STANDARD LENGTH Versatile Interface Structure (VIS) upper receiver assembly. The VIS is a polylithic upper receiver assembly that ties the normally individual receiver and handguard into an aggregate single part. Includes shell deflector only.
Dust cover omitted for lightweight, smooth, snag-free function Rail height slightly higher than A3 upper State-of-the-art aluminum material Picatinny Rail
Machined from a 7075-T6 aircraft allloy forging Anodized black and Teflon coated Bolt modified 180 for left side ejection Right side port cover boss is unmachined All dimensions are held to exacting Military requirements
Raise the axis of your AR without the loss of rigidity, plus allows you to mount additional accessories on the two lower Weaver rails Features include: Left-hand ejection and the standard right side forward assist. Right side port cover boss remains un-milled.
Same great construction as our standard Hi-Rider, now available in left-hand ejection Rail height approximately 1 7/8 above bore center line Does not feature forward assist, dust cover or ejection port cover for snag-free operation.
FTT-01SPLPB
Retail . . .$199.95
URSP-01A2
Retail . . .$199.95
FTT-SPB
Retail . . .$249.00
FTT-01SPB
Retail . . .$249.00
These left handed upper assemblies do not include the charging handle or forward assist.
These left handed upper assemblies do not include the charging handle or forward assist.
54
TACTICAL LATCH
CL-T Retail . . . . . .$19.95
Retail . . . . . .$59.95
ACCESSORIES-GAS SYSTEM
GASBUSTER MILITARY BIG BADGER CHARGING GASBUSTER CHARGING HANDLE, BIG FLAT LATCH LATCH CHARGING HANDLE HANDLE, GEN II TAC LATCH
UR-M84BLF Retail . . . . .$86.75 UR-M84MBL Retail . . . .$89.95 UR-18-G2 Retail . . . . . .$19.95
LATCH ONLY
A smaller profile Tactical latch for the AR series of rifles, allows the easy operation of the charging handle with either hand. M69 Gas Buster A-15/E-16/AP4 Charging Handle by PRI. Features the Big Flat Latch. Increases safety by inhibiting harmful blowback gas and oil particles from striking shooter's face and glasses." M69 Gas Buster A-15/E-16/AP4 Charging Handle by PRI. Features the Big Latch. Increases safety by inhibiting harmful blowback gas and oil particles from striking shooter's face and glasses."
CH-G2
Retail . . . . . .$43.95
FORWARD ASSISTS
UR-C4 Retail . . . . . .$20.00
Retail . . . . . .$17.99
UR-C4A = TEARDROP
UR-C4A
Retail . . . . . .$20.00
Oversized latch handle that is quick & easy to cycle. FLAT. Latch Only. Oversized latch handle that is quick & easy to cycle. Latch Only. Manufactured by SOG Armory. Features a stainless steel Tac Latch and a standard aluminum charging handle. Sold only as a complete assembly.
55
ACCESSORIES-GAS SYSTEM
Manufactured by DPMS! Low profile gas block designed to fit under the free float tube. Machined from 4130 steel.
.750 Diameter .936 Diameter
GB-SASS-1
Retail . . . .$109.95
.936 Diameter
Single rail gas block for .308 cal. rifles. Picatinny rail on top of gas block. Correct height for the LR-308 rifles with the Lo-Pro style upper receiver to attach iron sights. Rifles with the .308 A3-style upper receivers should use GB-SR7 (.750 dia. barrels) or GB-SR-9 (.936 dia. barrels).
The Vltor Low-Profile Gas Block covers one-inch of the barrels surface and is made to the tightest tolerance. This gas block is offered in 4140 carbon steel. Clamp Mount Style.
The Vltor Low-Profile Gas Block covers one-inch of the barrels surface and is made to the tightest tolerance. This gas block is offered in 17-4PH stainless steel. Clamp Mount Style.
VLTOR SET SCREW VLTOR SET SCREW GAS BLOCK, STAINLESS GAS BLOCK
GB-2SS Retail . .$58.95 GB-2S Retail . .$51.95
New production Micro Gas Block by CMMG. Ultra com pact design fits standard .936, .750, and.625 diameter barrels. Secures with two set screws. 4150 steel.
The VST folding front sight and gas block is an all-steel, flip-up design, with a spring loaded dual-plunger detent. There is no lock. If hit, the sight will fold down, rather than damage a locking mechanism. It incorporates a QD sling swivel cup mount, and uses an AK front sight post.
YANKEE HILL RAILED GAS AR15 GAS SYSTEM KITS BLOCK w/BAYONET LUG
GB-YHM-9836A Retail . .$72.95 Retail . . . . . . . . . . . . . . . .$28.95
GS-KT - STANDARD GS-KTC - CARBINE
This gas block replaces your existing front sight to provide a simple, low profile design that can be used to mount a rifle length forearm to a carbine length barrel. It is mounted by the use of two set screws. Manufactured from high quality steel and finished with a Mil Spec phosphate coating.
This gas block replaces your existing front sight and allows the user to mount accessories to its top Picatinny rail while retaining the bayonet lug and sling mount. It is mounted by the use of four socket head cap screws for easy installation. This gas block allow the mounting of our forearms without the removal of your muzzle accessory.
GS-KTC Includes 1 1 3 2 1 Gas Tube Roll Pin (BL-03) Car Length Gas Tube (BL-04A) Bolt Gas Rings (BT-01) Bolt Carrier Key Screws (BT-10) Bolt Carrier Key (BT-11)
56
GB-4R
Retail . . . . . .$49.95
308-FF-CFC
Aluminum gas block with four Picatinny rails for mounting multiple accessories.Currently made for the DPMS Bull barrels. Bore diameter is .936 anodized black. Also available in .750. .750 dia. = GB-4RA .936 dia. = GB-4R Aluminum gas block fits DPMS Bull barrels or any barrel with a diameter of .936 at the gas port. Hardcoat anodized black. Also Available for Super Bull barrels with 1.10 diameter hole. BULL-02-SB Also Available for standard barrels with .750 diameter hole. BULL-02-ST
Retail . . . .$133.50
ACCESSORIES-GAS SYSTEMS
GB-4RA
Retail . . . . . .$49.95
The 2.1 diameter .308 caliber carbon fiber free float handguards from DPMS stay cooler than the standard aluminum free float tubes and weigh less, providing you with a unique alternative to the traditional handguard. The carbon fiber utilized in these free float tubes works in two ways, internally the unidirectional carbon fiber increases the strength and stability of the tube while externally the bi-directional carbon fiber provides a textured look and feel to the free float tube. Additionally, an internal layer of fiberglass prevents corrosion between the aluminum tube and the carbon fiber, ensuring a long lasting lightweight alternative tube. Includes the hard anodized barrel nut. Standard: Length = 12.6875, Weight = 0.45 lbs. Carbine: Length = 7.3125, Weight = 0.3 lbs.
Single rail gas block .750 dia. Picatinny rail on top of gas block.
GS-JPGS-2S
Retail . . . .$79.95
Steel Gas Block, .750 dia Manufactured by Clark Custom.. LR-308 Carbon Fiber Handguard is light-weight and has a unique appearance.
Aluminum Construction
Anodized Black
Ribbed not Knurled Free Float Accuracy All two piece Construction.
Aluminum Bull Barrel Gas Block, .936 dia Single rail gas block .936 dia. Picatinny rail on top of gas block.
GS-JP-4S
Retail . . . . .$89.95
V-Tac Modular Hand Guard System for Carbine length gas system on DPMS LR-308 16" or 18" barrels 1.75 ID, 2.00 OD, 7.0" OAL All matte black finish
V-Tac Modular Hand Guard System for DPMS LR-308 or Knights SR-25 type rifles. 1.75 ID, 2.00 OD, 12.5" OAL Weight: 15 oz. All matte black finish
SST w/Quick Detach Point Large Bore Gas Block, .936 dia GT Steel single rail gas block. Fits standard heavy barrels.
57
FF-CFC
Retail . . . . . .$89.00
CARBINE LENGTH
ACCESSORIES-HANDGUARDS
The .308 cal. version of the 4-rail free float tube features a solid one-piece free float tube made from 6066-T6 aluminum. The Picatinny style rails are integrally machined into the free float tube. Two rail heights are available, one for the A3-style upper receiver and the other for the original LR-308 upper receiver. Each rail height is available in two lengths, standard and carbine. The free float tubes are vented and hard coat anodized per Mil Spec and matte black in color. Overall width dimension is 2.1, only slightly wider than the AR free float tubes and include a manganese phosphated steel locking collar to control the timing of the rails.
The 2 diameter carbon fiber free float handguards from DPMS stay cooler than the standard aluminum free float tubes and weigh less, 40% less, providing you with a unique alternative to the traditional handguard. The carbon fiber utilized in these free float tubes works in two ways, internally the unidirectional carbon fiber increases the strength and stability of the tube while externally the bi-directional carbon fiber provides a textured look and feel to the free float tube. Additionally, an internal layer of fiberglass prevents corrosion between the aluminum tube and the carbon fiber, ensuring a long lasting lightweight alternative tube. Includes the hard anodized barrel nut. Standard: Length = 12.625, Weight = 0.55 lbs. Carbine: Length = 7.25, Weight = 0.35 lbs.
STANDARD LENGTH
FF-02 Retail . . . . . .$53.95
CARBINE LENGTH
FF-01 Retail . . . . . .$49.95
Aluminum Construction
Anodized Black
Ribbed not Knurled Free Float Accuracy All two piece Construction.
This 4-rail free float tube for the LR-308 Rifle Series features a solid one-piece free float tube made from 6000 Series aluminum with a T6 heat treatment. The Picatinny style rails are integrally machined but now feature 4 removable rails at the front of the tube. 16 individual vents help increase the airflow to the barrel. The low profile design of the free float tube is compatible to the 308 A3-Style upper receiver.
CARBINE LENGTH
Same as the AR-15 Stabilizer guard but with a wider mounting block to accommodate the added weight and recoil of a 308. Made with a full length M1913 integral down the full length of the top. Drilled and tapped to accept the Picatinny rail sections. Aluminum alloy, Mil spec hard coat black anodizing.
This 12" Lite Rail is machined from 6061-T6 Aircraft Grade Hardened Aluminum. The rail's unique "Bolt Up" mounting system mates with the upper receiver to create a singular 'monolithic' rail along the entire top portion of the rifle.
STANDARD LENGTH
FF-HGR Retail . . . . . .$89.95
CARBINE LENGTH
FF-HCAR Retail . . . . . .$84.95
58
FF-4R
Retail . . .$134.00
ACCESSORIES-HANDGUARDS
The improved version of the 4-rail free float tube features a solid one-piece free float tube made from 6000 Series aluminum with a T6 heat treatment. The Picatinny style rails are integrally machined into the free float tube. The Picatinny rails are designed for the attachment of foregrips, flashlights, optics or any other type of rail mounted accessories. The free float tube is also vented with 16 individual vents for increased airflow to the barrel. The overall width dimension is 2 3/8 giving it the same feel as a AP4 handguard.
P.O.F. P9 4-RAIL
FF-P9 Retail . . . . .$269.00
Full-Length Free Float tube with 4-Rails for mounting accessories. Top rail extends fully to the rear of the A3 Upper Receiver rail. Bipod/Sling Stud included and can be installed on either side of the tube or on the bottom.
Full-Length Free Float tube with 4-Rails for mounting accessories. Top rail extends across a majority of the A3 Upper Receiver rail. Bipod/Sling Stud included and can be installed on either side of the tube or on the bottom.
Mid-Length Free Float tube with 4-Rails for mounting accessories. Top rail extends fully to the rear of the A3 Upper Receiver rail. Bipod/Sling Stud included and can be installed on either side of the tube or on the bottom.
Mid-Length Free Float tube with 4-Rails for mounting accessories. Top rail extends across a majority of the A3 Upper Receiver rail. Bipod/Sling Stud included and can be installed on either side of the tube or on the bottom.
P.O.F. P4 4-RAIL
FF-P4 Retail . . . . .$249.00
Standard Length. AR-15/M-16 free float aluminum forend with over-molded rubber gripping area. Carbine Length Free Float tube with 4-Rails for mounting accessories. Top rail extends fully to the rear of the A3 Upper Receiver rail. Bipod/Sling Stud included and can be installed on either side of the tube or on the bottom. Carbine Length Free Float tube with 4-Rails for mounting accessories. Top rail extends across a majority of the A3 Upper Receiver rail. Bipod/Sling Stud included and can be installed on either side of the tube or on the bottom. Hogue Soft Rubber Free Float Tube, Carbine Length. AR-15/M-16 free float aluminum forend with over-molded rubber gripping area.
FF-15204
Retail . . . . .$74.99
OD GREEN
59
YH FREE FLOAT 4-RAIL YH FREE FLOAT 4-RAIL FOREARM, 9.2 FOREARM, 7.2 (CARBINE)
FF-9634 Retail . . . .$128.50 FF-YHM-9631 Retail . .$120.00
Overall Length: 12.5, Weight: 14.75 oz. *New and Improved* Now utilizing anti-rotation screws to insure that the forearm stays solid even under strenuous use. With the addition of the anti-rotation screws the forearms are now even better suited for forward grips and optics. Features include: mounting points and Mil. Spec. Picatinny rails. The barrel nut and forearm tube are made of aircraft quality aluminum and hardcoat anodized to Mil. Specs. The jam nut is made from quality steel and phosphate coated. All assemblies include: one jam nut, one barrel nut, and one forearm tube.
Overall Length: 9.675, Weight: 12.9 oz. *New and Improved* Now utilizing anti-rotation screws to insure that the forearm stays solid even under strenuous use. With the addition of the anti-rotation screws the forearms are now even better suited for forward grips and optics. Features include: mounting points and Mil. Spec. Picatinny rails. The barrel nut and forearm tube are made of aircraft quality aluminum and hardcoat anodized to Mil. Specs. The jam nut is made from quality steel and phosphate coated. All assemblies include: one jam nut, one barrel nut, and one forearm tube.
Overall Length: 9.2, Weight: 12.4 oz. *New and Improved* Now utilizing anti-rotation screws to insure that the forearm stays solid even under strenuous use. With the addition of the anti-rotation screws the forearms are now even better suited for forward grips and optics. Features include: mounting points and Mil. Spec. Picatinny rails. The barrel nut and forearm tube are made of aircraft quality aluminum and hardcoat anodized to Mil. Specs. The jam nut is made from quality steel and phosphate coated. All assemblies include: one jam nut, one barrel nut, and one forearm tube.
Overall Length: 7.2, Weight: 10.6 oz. *New and Improved* Now utilizing anti-rotation screws to insure that the forearm stays solid even under strenuous use. With the addition of the anti-rotation screws the forearms are now even better suited for forward grips and optics. Features include: mounting points and Mil. Spec. Picatinny rails. The barrel nut and forearm tube are made of aircraft quality aluminum and hardcoat anodized to Mil. Specs. The jam nut is made from quality steel and phosphate coated. All assemblies include: one jam nut, one barrel nut, and one forearm tube.
ACCESSORIES-HANDGUARDS
FREE FLOAT FOREARM YH FREE FLOAT SYSTEM, CARBINE LENGTH 4-RAIL FOREARM, 4.15
FF-YHM-9431A Retail . .$86.95 FF-YHM-9809A Retail . .$105.00
Yankee HIll Machine Customizable Free Float Forearm System! These customizable tubes are a great addition to any firearm just as they are. They feature slotted heat vents and two mounting points. Each tube is drilled and tapped at the 3, 6, 9 and 12 oclock positions. All assemblies include: one jam nut, one barrel nut, and one forearm tube. Overall length: 12.5 in - Weight 14.6 oz.
Yankee HIll Machine Customizable Free Float Forearm System! These customizable tubes are a great addition to any firearm just as they are. They feature slotted heat vents and two mounting points. Each tube is drilled and tapped at the 3, 6, 9 and 12 oclock positions. All assemblies include: one jam nut, one barrel nut, and one forearm tube. Overall length: 9.675 in - Weight 12 oz.
Yankee HIll Machine Customizable Free Float Forearm System! These customizable tubes are a great addition to any firearm just as they are. They feature slotted heat vents and two mounting points. Each tube is drilled and tapped at the 3, 6, 9 and 12 oclock positions. All assemblies include: one jam nut, one barrel nut, and one forearm tube. Overall length: 7.2 in - Weight 9.5 oz.
*New and Improved* Now utilizing anti-rotation screws to insure that the forearm stays solid even under strenuous use. With the addition of the anti-rotation screws the forearms are now even better suited for forward grips and optics. Features include: mounting points and Mil. Spec. Picatinny rails. The barrel nut and forearm tube are made of aircraft quality aluminum and hardcoat anodized to Mil. Specs. The jam nut is made from quality steel and phosphate coated. All assemblies include: one jam nut, one barrel nut, and one forearm tube.
YH CARBINE SMOOTH HOT ROD HANDGUARD V-TAC MODULAR w/HANDGRIP HANDGUARD SYSTEM FOREARM
FF-HGS Retail . . . . .$119.95 Retail . . . . . . . . . . . . . . .$149.95 FF-YHM-5000 Retail . . .$136.00
1.75 ID 2.00 OD, 7.0" OAL. This CASV chassis is made entirely of aluminum with exception to the stainless steel mounting hardware. After mounted, the CASV adds less than 1lb to the firearm's overall weight. Hot Rod Handguard with adjustable sliding handstop. The JP modular handguard system has been re-designed to offer the best versatility of any handguard system while retaining the lightweight and cooling capacity of their original design. This free floating forearm features a smooth design for a more comfortable grip while incorporating a full length top rail. The forearm also features three 2.5" rails that extend beyond the front sight to allow the mounting of accessories.
60
Weight: 14.0 oz. Manufactured by Midwest Industries No removal of barrel or front sight for installation. Simply cut off the delta ring for a easy install. MIL-STD 1913 rails. T-marked for accessory location. Constructed of 6061 hard coat anodized for a lifetime of service. Uninterrupted or monolithic look upper rail. High quality at an affordable price.
Weight: 13.5 oz. Manufactured by Midwest Industries MIL-STD 1913 rails. T-marked for accessory location. Constructed of 6061 hard coat anodized for a lifetime of service. Uninterrupted or monolithic look upper rail. High quality at an affordable price.
ACCESSORIES-HANDGUARDS
Manufactured by Midwest Industries. Carbine length Free Float Tube Handguard, 4-rail two piece.
.$179.00 HG-MCTAR18
Manufactured by Midwest Industries No removal of barrel or front sight for installation. Simply cut off the delta ring for a easy install. MIL-STD 1913 rails. T-marked for accessory location. Constructed of 6061 hard coat anodized for a lifetime of service. Uninterrupted or monolithic look upper rail. High quality at an affordable price.
Manufactured by Midwest Industries No removal of barrel or front sight for installation. Simply cut off the delta ring for a easy install. MIL-STD 1913 rails. T-marked for accessory location. Constructed of 6061 hard coat anodized for a lifetime of service. Uninterrupted or monolithic look upper rail. High quality at an affordable price.
FF-249-04
Retail . . .$152.00
Made by Yankee Hill Machine. These handguards are designed to replace your standard plastic handguards with a 4-rail Picatinny design. Simply remove your existing handguard panels and insert these in their place.
Made by Yankee Hill Machine. These handguards are designed to replace your standard plastic handguards with a 4-rail Picatinny design. Simply remove your existing handguard panels and insert these in their place.
Made by Yankee Hill Machine. These handguards are designed to replace your standard plastic handguards with a 4-rail Picatinny design. Simply remove your existing handguard panels and insert these in their place.
61
HANDGUARDS
GLACIERGUARDS
No metal heatshield required! BL-FG Retail . . . . . .$39.95 BLACK
DCM
US Patent # 6,945,154
ACCESSORIES-HANDGUARDS
GlacierGuards
BL-FGT Retail . . . . . .$44.95 TAN BL-FGG Retail . . . . . .$44.95 OD GREEN
Free floating handguards are used by those that want the best accuracy, but free float tubes in the past did not meet the requirements for DCM matches, and they look different. Now DPMS has a replacement free float tube that replaces the factory handguards and looks the same as the factory. Easy to install for better accuracy. Includes swivel rivet. Replace your EM-16/A-15 handguard for better accuracy.
For more than 100 years, fins have been used to cool metal objects. Now DPMS Panther Arms brings that concept to your A-15 rifle. DPMS Panther Arms introduces the GlacierGuards an AP4 style handguard that utilizes 15 internal fins, rather than the standard aluminum double-shield, for heat dispersion. These unique fins, while dispersing the heat generated by rifle fire, also provide unsurpassed strength and rigidity for the handguard. Externally, the GlacierGuards feature 15 ribs that mirror the internal fins, and provide the shooter an enhanced grip. The GlacierGuards accommodate barrels with diameters less than one inch, namely the military contoured barrel and the industry standard heavy barrel. Made of a high tech, temperature resistant polymer that withstands temperatures greater than 500 degrees. This allows the handguards to resist over-heating after continuous fully-automatic fire for over 200 rounds. The fiber-reinforced polymer provides additional strength and rigidity and keeps the handguards weight at just one half pound per pair, compared to the standard .4 pounds per pair. US Patent # 6,945,154.
DCM
Custom formed lead weight for the bottom half of the A2 handguards-DCM Handguards. Adds 3.334 lbs. to your handguard for extra weight and accuracy. No shipments to California
AP4 HANDGUARD
BL-02 Retail . . . . .$19.95
M-33 HANDGUARDS
HG-M33 Retail . . . . . .$84.99
Double walled heat shield AP4 handguard. Mil-Spec. Large Oval Design!
Mil-Spec!
Small oval design, glass filled polymer. Single wall, anodized heat shield. Tight fitting. Black in color.
Made by Command Arms Accessories. The M33 is built to fit the M16/AR15 carbine. Replace your existing hand-guard with this polymer handguard which provides 2 mounting rails, complete with 2 Vented and 2 Non-Vented thermal rubber rail covers and heat shields. No tools or gunsmithing required, handguard mounts just like factory handguards. Rails can be mounted on the left/right side, or the top/bottem of the handguard. The SureFire 4-Rail M73 Handguard System. Four (4) rail covers included. LIFETIME WARRANTY
Retail . . . . . . . . . . . . . . . .$99.95
POLYMER
Carbine Length. Polymer and aluminum handguards. 4-sided Picatinny rail system Metal heatshields dissipate high tempertures producted during sustained rapid fire. Thermal rubber covers enhance grip and protect rails when not in use. No gunsmithing required, handguards mounts just like factory handguards. FREE RAIL COVERS INCLUDED LIFETIME WARRANTY
Standard Length. Polymer handguards. 4-sided Picatinny rail system Metal heatshields dissipate high tempertures producted during sustained rapid fire. Thermal rubber covers enhance grip and protect rails when not in use. No gunsmithing required, handguards mounts just like factory handguards. 2 Vented and 2 Non-Vented Rail covers included. LIFETIME WARRANTY
HG-M44SM
HG-M44SM = BLACK
Retail . . .$105.99
ALUMINUM
62
VERTICAL GRIPS
SOG GRAPHITE VERTICAL GRIP
Retail . . . . . . . . . . . . . . . .$39.95
VG-1002-B = BLACK VG-1002-G = OD GREEN VG-1002-T = TAN
YANKEE HILL QUICK VERTICAL GRIP BY ACTION FOLDING GRIP COMMAND ARMS
VG-YHM-9640 Retail . . .$74.50 Retail . . . . . . . . . . . . . . . .$25.95
VG-BVG = BLACK VG-BVGG = OD GREEN VG-BVGT = TAN
ACCESSORIES-VERTICAL GRIPS
Graphite vertical grip with aluminum lock down post. Available in black, OD green and tan.
This grip is actuated with the push of a button. It locks securely in the folded and battle-ready positions. Designed to function properly even under strenuous military use. Installs easily on any Picatinny rail with the use of the supplied socket head cap screw.
Vertical Ergonomic Grip by Command Arms. Quick, detachable with 3-battery storage compartments. Screw driver required. Available in black, OD green and tan.
Forward Grip with Magazine Holder combines forward gripand magazine holder. Quick release or secure bolt attachment. Left side magazine release button. Lightweight polymer construction.
HAND GRIP FOR 4-RAIL VERTICAL FORWARD FREE FLOAT TUBE GRIP (POP BOTTLE)
FF-GR Retail . . . . . .$59.95 VG-4253 Retail . . . . . .$15.00
XTA Tactical, lightweight vertical grip will attach to Picatinny rails. Comes with a 6 mounting rail for standard handguards. Made by the John Masen Company.
Forward grip for mounting on the 4 Rail Free Float Tube. Quickly attaches and detaches with thumbscrew. ALUMINUM!
Vertical Forward Grip by ERGO. Ejection molded, slides onto standard Picatinny or Weaver rail. Set-screw retention. Extremely tough. Black.
Vertical foregrip attaches to the Picatinny rail on the forearm and provides a laser beam upon gripping.
FOLDING VERTICAL ERGONOMIC VERTICAL GRIP by COMMAND ARMS GRIP by COMMAND ARMS
VG-FFG2 Retail . . . . .$33.99 VG-AVG Retail . . . . . .$19.99
Vertical & Horizontal tactical grip, push button release converts grip from horizontal to vertical Ergonomic design Skeletonized for reduced weight Folds under so it is out of the way when not in use LIFETIME WARRANTY
Distinctive ergonomically designed tactical vertical grips. Facilitates natural fighting stance holds on your rifle Improved performance and reaction time, reduces on target time increases muzzle control during rapid fire Ergonomically designed with finger grooves Plugged storage compartment LIFETIME WARRANTY
Distinctive ergonomically designed tactical vertical grips. Facilitates natural fighting stance holds on your rifle Improved performance and reaction time, reduces on target time increases muzzle control during rapid fire Ergonomically designed with finger grooves Plugged storage compartment LIFETIME WARRANTY
Permits the operator to get "on target" faster and improves muzzle control during rapid fire. Allows the weapon to be held with a natural fighting stance. Fits any Weaver or Picatinny rail. Interior of grip serves as a plugged storage compartment. No tools or gunsmithing required. LIFETIME WARRANTY
63
RAIL COVERS
Retail . . . . . . . . . .$8.00/EA. PC.
Full Rail Cover, Medium
Full Rail Cover Black FF-4362BK OD Green FF-4362OD Coyote Brown FF-4362CB Long Length Covers 15 slots
Full Rail Cover Black FF-4361BK OD Green FF-4361OD Coyote Brown FF-4361CB Medium Length Covers 10 slots
Full Rail Cover Black FF-4360BK OD Green FF-4360OD Coyote Brown FF-4360CB Short Length Covers 5 slots
ACCESSORIES-BAYONETS
This unique tactical grip allows the operator to use his 1" Flashlight. The most ergonomically designed vertical foregrip. Has storage compartment for batteries, cleaning kit, etc. A 1" flashlight mount is incorporated along with an On/Off Trigger located on the grip itself. (No need for bulky and pricey pressure switches) Fits any weapon with a weaver or picatinny rail. Mounted using a quick release locking system with an additional locking screw as backup. No gunsmithing required. Molded from reinforced polymer composite. Super lightweight.
Low Profile Rail Cover Black FF-4373BK OD Green FF-4373OD Coyote Brown FF-4373CB Long Length Covers 18 slots
Low Profile Rail Cover Black FF-4370BK OD Green FF-4370OD Coyote Brown FF-4370CB Short Length Covers 5 slots
These covers can be used to form a very low profile grip and protect the unmounted rail area from damage. Made from Santoprene, these covers have a rubbery surface and are easily shortened by cutting to length. Available in a variety colors and textures. Prices reflect individual piece prices. Sold individually. Made by Falcon Industries.
SURE GRIP
PS-RGS Retail . . . . . .$9.98
MAGPUL RAIL COVERS M9 LIGHT WEIGHT M9 BAYONET & BAYONET & SCABBARD SCABBARD
Retail . . . . . . . . . . . . .$11.95/ea.
FF-MAG012-BLK = BLACK FF-MAG012-DKE = DARK EARTH FF-MAG012-OD = OD GREEN
Retail . . . . . . . . . . . . . . .$115.00
BL-M9LW = BLACK BL-M9LWT = TAN BL-M9LWG = GREEN
Retail . . . . . . . . . . . . . . . .$95.00
BL-M9 = BLACK BL-M9T = TAN
Pac-Skin is a new generation of non-slip, sure gripping rubber technology. This peel-n-stick rubber material provides the ultimate gripping surface on those items where improving the grip was difficult, if not impossible, in the past. A finely textured neoprene rubber surface coupled with a peel-n-stick adhesive backing makes a perfect accessory for your favorite rifle. Two pieces - Pistol grip and Forend.
Each rail cover covers 15 slots of rail Provides rubbery grip surface. Protects the operator from sharp rail edges. Protects unmounted rail areas from damage. Prevents damage to gear
The new unit weighs 15% LESS then the current standard M9 model by using a special high grade stainless steel alloy with aluminum interior components. Performance and balance are exceptional with this new model.
7 blade, Blade .235 thick, 12-1/8 OAL Black oxide non-reflective surface Milled sawteeth on back. Textured thermoplastic nylon handle and scabbard. Equipped with a quick release military holster.
BL-M9G
Retail . . . . .$105.00
OD GREEN
M-7 BAYONET
BL-M7 Retail . . . . . .$29.95
M-10 SCABBARD
BL-M7S
7 blade, Blade .235 thick, 12-1/8 OAL Black oxide non-reflective surface Milled sawteeth on back Textured thermoplastic nylon handle and scabbard. Equipped with a quick release military holster. 8 blade, Blade .200 thick, 13-1/4 OAL Phosphate non-reflective surface 1-3/4 Mission Serration Fits the EM-16, AP4 & A-15 Dynaflex handle reduces hand fatigue with positioning access point. Military production scabbard for the M-7 bayonet. Black plastic with tie straps.
Retail . . . . . .$13.50
Available in two sizes. Fits over the barrel in front of the sight. (2pc. construction) Lightweight A1 Barrel .570 dia. BL-LUG Heavy Barrel A2 .725 dia. BL-LUG-H
BL-LUG-H
Retail . . . . .$19.95
Heavy Barrel A2
64
MANGONEL SIGHT KIT Kit contains both the Front & Rear Mangonel sights.
RS-MGK
Retail . . . .$224.95
ACCESSORIES-REAR SIGHTS
Attaches to various flattop upper receivers. Designed using the Picatinny rail system. Aluminum & steel construction. Height of sight will line up with standard front sights. Made by DPMS. 300 meters plus of elevation - Not 800. Not intended for long range. Backup iron sights only. LR-308 rifles ship with 6/3.
Manufactured by Midwest Industries. 6061 aluminum Locking detent in the up position Windage knob same as standard AR, NO ELEVATION ADJUSTMENT
Unique, new, flip-up sight for AR-style rifles is one of the most versatile available. Key features include: rock-solid 2 bolt mounting system, bi-directional adjustment for both windage and elevation, positive mount in the upward position, improved sight picture with a large aperture peep sight. The sight will mount on any standard Weaver or Picatinny rail.
NM REAR APERTURES
Retail . . . . . . . . . . . . . . . .$14.95
Sight Set
Both apertures are bored on the same plane. Larger Ghost ring aperture has a .230 inner dia. and a .070 wall thickness for greater light transmission. The smaller precision aperture has a .100 inner dia. with a .100 wall thickness which allows shooter to obtain a more precise zero. Drop-in replacement for A1 or A2 rear sights. Made of 416 Stainless steel, heat treated to rockwell 20, blackened with a matte finish.
Features small long-range aperture with standard A2 large short-range aperture. UR-27-NM UR-27A-NM .046 and .200 dia. .052 and .200 dia. New DPMS Hooded Aperture sight with a .040 diameter peep hole. 8620 steel, interchangeable with your A2 rear sight assembly.
Front Sight
3-Dot green front & rear night sights for M16/AR15. Installation tool included. Green lamps are warranted for 12 years from the date of manufacture. The brightness obtained from the tritium content is focused through the sapphire lens to give the maximum possible illumination. Sight blades are machined from steel not cast.
Also available is an aperture with both holes undersized UR-27B-NM .040 and .030 dia.
FS-CP25F
Retail . . . . .$54.95
65
2 1
Replaces standard rear sight to provide 1/4 min. windage and 1/4 min. elevation adjustments. Complete assembly includes choice of aperature.
ACCESSORIES-REAR SIGHTS
SIGHT LUG
UR-29A Retail . . . . .$29.95
RAPIDEX KNOB
UR-39A1 Retail . . . . . .$9.00
Manufactured by SOG Armory. Used to install A1/A2 style adjustable front sights.
TL-A3 Keychain Style A2 TL-A4 Keychain Style A1 Key Ring not included. Ready to install on your keychain. For use with the EM-16A/A-15A2 rifles. Used to install A2 style adjustable rear sights.
Quickly snaps on and off. Protects front and rear sights. Made of hard plastic. Price reflects both front and rear protectors. Manufactured by Fulton Armory
66