Beruflich Dokumente
Kultur Dokumente
PQ05RD11 Series
PQ05RD11 Series
1A Output, General Purpose Low Power-loss Voltage Regulators
s Outline Dimensions s Features
Low Power-loss (Dropout voltage : MAX.0.5V at Io=0.5A) Line-up for 5V, 9V and 12V output type Compact resin package (TO-220 package) High-precision output voltage type Output voltage precision : 3.0% Built-in ON/OFF control function Built-in overcurrent protection, overheat protection, ASO protection circuit
4-(1.4)
7.40.2
(Unit : mm)
10.2MAX
3.60.2
4.50.2 2.80.2
29.1MAX
PQ05RD11
4-1.4
13.5MIN
+0.3 -0
4-0.6
+0.2 -0.1
s Applications
Power supplies for various electronic equipment such as AV, OA equipment
3-(2.54)
(0.5)
1 2 3 4
(Ta=25C) Symbol VIN VC IO PD1 PD2 Tj Topr Tstg Tsol Rating 20 20 1.0 1.4 15 150 -20 to +80 -40 to +150 260 (For 10s) Unit V V A W C C C C
*2
Input voltage ON/OFF control terminal voltage Output current Power dissipation (No heat sink) Power dissipation (With infinite heat sink) Junction temperature Operating temperature Storage temperature Soldering temperature
All are open except GND and applicable terminals. Overheat protection may operate at 125=<Tj=<150C
*1 *2
In the absence of confirmation by device specification sheets,SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs,data books,etc.Contact SHARP in order to obtain the latest version of the device specification sheets before using any SHARP's device.
4.8MAX 15.60.5
3.20.1
(1.5)
PQ05RD11 Series
(Unless otherwise specified, conditions shall be IO=0.5A,*3,Ta=25C) Conditions Io=5mA to 1.0A *4 , Io=5mA Tj=0 to 125C, Io=5mA *5
*6
Load regulation Line regulation Temperature coefficient of output voltage Ripple rejection Dropout voltage ON-state voltage for control ON-state current for control OFF-state voltage for control OFF-state current for control Quiescent current
Unit V % % %/C dB V V A V mA mA
*3 *4 *5 *6
PQ05RD11:VIN =7V, PQ09RD11:VIN =11V, PQ12RD11: VIN =14V PQ05RD11:VIN = 6 to 12V, PQ09RD11:VIN =10 to 16V, PQ12RD11: VIN =13 to 19V Input voltage shall be the value when output voltage is 95% in comparison with the initial value. In case of opening control terminal 4, output voltage turns on.
Fig.1
VIN
Test Circuit
1 q 2 q 4 q 3 q 0.33F VC IC 47F VO
Fig.2
IO RL V eo ~
A
+
IO
~ ei
0.33F
A
Iq
V
RL
VIN
47F
f=120Hz (sine wave) ei=0.5Vrms VIN= 7V (PQ05RD11) VIN=11V (PQ09RD11) VIN=14V (PQ12RD11) IO=0.3A RR=20 log (ei/eo)
Fig.3
20
Power dissipation PD (W)
15
10
5 PD1 0 -20
0 20 40 60 80 Ambient temperature Ta (C) Note) Oblique line portion:Overheat protection may operate in this area.
Fig.4
100
80 60 40 20 0 0
VIN=20V VIN=15V
VIN=7V
2.5
PQ05RD11 Series
Fig.6
100
Relative output voltage (%)
80 60 40 20 0 0
VIN=20V VIN=15V
80 60 40 20 0 0
VIN=20V
VIN=11V
VIN=14V
2.5
2.5