Beruflich Dokumente
Kultur Dokumente
Australian Standard
This is a free 5 page sample. Access the full version at http://infostore.saiglobal.com.
Review of Australian Standards. To keep abreast of progress in industry, Australian Standards are subject
to periodic review and are kept up to date by the issue of amendments or new editions as necessary. It is
important therefore that Standards users ensure that they are in possession of the latest ed ition, and any
amendments thereto.
Full details of all Australian Standards and related publications will be found in the Standards Australia
Catalogue of Publications; this information is supplemented each month by the magazine ‘The Australian
Standard’, which subscribing members receive, and which gives details of new publications, new editions
and amendments, and of withdrawn Standards.
Suggestions for improvements to Australian Standards, addressed to the head office of Standards Australia,
are welcomed. Notification of any inaccuracy or ambiguity found in an Australian Standard should be made
without delay in order that the matter may be investigated and appropriate action taken.
Australian Standard
This is a free 5 page sample. Access the full version at http://infostore.saiglobal.com.
PREFACE
This Standard was prepared by Standards Australia’s Committee for PVC Rainwater Goods, under the
direction of the Plastics Standards Board, to supersede AS 1273.1—1974, Unplasticized PVC (UPVC)
downpipe and fittings for rainwater, Part 1: Downpipes, and AS 1273.2—1974, Unplasticized PVC (UPVC)
downpipe and fittings for rainwater, Part 2: Moulded fittings.
This Standard incorporates the content of both AS 1273.1 and AS 1273.2. It is technically equivalent to
both these Standards, however the impact test is now carried out at 20°C only.
CONTENTS
Page
This is a free 5 page sample. Access the full version at http://infostore.saiglobal.com.
1 SCOPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 REFERENCED DOCUMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3 DEFINITION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4 CLASSIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
5 GENERAL REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
6 PERFORMANCE REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
7 MARKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
STANDARDS AUSTRALIA
Australian Standard
Unplasticized PVC (UPVC) downpipe and fittings for rainwater
1 SCOPE This Standard specifies requirements for rectangular and circular UPVC downpipe and fittings
for the disposal of rainwater. Such pipes and fittings are suitable for external or internal use above ground
where the head of water does not exceed 15 m.
NOTE: Alternative methods for determining compliance with this Standard are given in Appendix A.
3 DEFINITION For the purposes of this Standard, the definition below applies.
3.1 Downpipe—a pipe for conveying rainwater, either externally or internally, from a roof or other parts
of a building.
4 CLASSIFICATION Pipe and fittings manufactured to this Standard shall be classified DOWNPIPE.
5 GENERAL REQUIREMENTS
5.1 Composition The material from which the pipe and fittings are produced shall consist of polyvinyl
chloride (PVC) together with additives necessary for the manufacture and performance of pipe to this
Standard.
The additives shall contain a minimum of 2 parts of titanium dioxide pigment per 100 parts mass of PVC
content, as determined by AS 1462.18.
5.2 Dimensions
5.2.1 Rectangular pipe When measured in accordance with AS 1462.1, the dimensions of rectangular pipe
measured at the midpoint of the sides shall comply with the requirements of Table 1.
5.2.2 Circular pipe When measured in accordance with AS 1462.1, the dimensions of circular pipe shall
comply with the requirements of Table 2.
5.2.3 Fittings When measured in accordance with AS 1462.1, the dimensions of sockets on fittings shall
conform with the dimensions of Table 3 or Table 4 for solvent cemented fittings (see also Figure 1 and
Figure 2), and Table 5 for rubber ring jointed fittings (see Figure 3).
COPYRIGHT
This is a free preview. Purchase the entire publication at the link below: