Beruflich Dokumente
Kultur Dokumente
Product Specification
Title
Customer MODEL DELL
*When you obtain standard approval, please use the above model name without suffix
APPROVED BY
SIGNATURE
SIGNATURE
/ REVIEWED BY / N.J. Seong / Manager PREPARED BY N.K. Cho / Engineer T.S. Yun / Engineer
Please return 1 copy for your confirmation with your signature and comments.
Ver. 0.0
1 / 31
Product Specification
Contents
No
COVER CONTENTS RECORD OF REVISIONS 1 2 3 3-1 3-2 3-3 3-4 3-5 3-6 3-7 4 5 6 7 7-1 7-2 8 8-1 8-2 9 A GENERAL DESCRIPTION ABSOLUTE MAXIMUM RATINGS ELECTRICAL SPECIFICATIONS ELECTRICAL CHARACTREISTICS INTERFACE CONNECTIONS LVDS SIGNAL TIMING SPECIFICATIONS SIGNAL TIMING SPECIFICATIONS SIGNAL TIMING WAVEFORMS COLOR INPUT DATA REFERNECE POWER SEQUENCE OPTICAL SFECIFICATIONS MECHANICAL CHARACTERISTICS RELIABLITY INTERNATIONAL STANDARDS SAFETY EMC PACKING DESIGNATION OF LOT MARK PACKING FORM PRECAUTIONS APPENDIX. Enhanced Extended Display Identification Data 26 26 27 29 25 25 6 8 9 11 11 12 13 14 17 24
ITEM
Page
1 2 3 4 5
Ver. 0.0
2 / 31
Product Specification
RECORD OF REVISIONS
Revision No Revision Date
0.0 Jun. 06. 2008
Page
-
Description
First Draft (Preliminary Specification)
EDID ver
0.0
Ver. 0.0
3 / 31
Product Specification
1. General Description
The LP154WX7 is a Color Active Matrix Liquid Crystal Display with an integral White LED backlight system. The matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in the normally white mode. This TFT-LCD has 15.4 inches diagonally measured active display area with WXGA resolution(800 vertical by 1280 horizontal pixel array). Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is determined with a 6-bit gray scale signal for each dot, thus, presenting a palette of more than 262,144 colors. The LP154WX7 has been designed to apply the interface method that enables low power, high speed, low EMI. The LP154WX7 is intended to support applications where thin thickness, low power are critical factors and graphic displays are important. In combination with the vertical arrangement of the sub-pixels, the LP154WX7 characteristics provide an excellent flat display for office automation products such as Notebook PC. LVDS & Timing Control Block
GIP(Gate In Panel)
General Features
Active Screen Size Outline Dimension Pixel Pitch Pixel Format Color Depth Luminance, White Power Consumption Weight Display Operating Mode Surface Treatment RoHS Comply Ver. 0.0 15.4 inches diagonal 344.0(H.) 222.0(V) 6.5(D,Max) [mm] 0.2588mm 0.2588 mm 1280 horiz. By 800 vert. Pixels RGB strip arrangement 6-bit, 262,144 colors 220 cd/m2(Typ.5 point) TBD 500g(Max.) Transmissive mode, normally white Glare treatment of the front polarizer Yes Jun. 06, 2008 4 / 31
POWER BLOCK
EDID BLOCK
800
Product Specification
Power Input Voltage Operating Temperature Storage Temperature Operating Ambient Humidity Storage Humidity
Note : 1. Temperature and relative humidity range are shown in the figure below. Wet bulb temperature should be 39C Max, and no condensation of water.
90% 80% 60 60%
50 40%
Humidity[(%)RH]
Storage
Operation
20% 10%
-20
10
20
30
40
50
60
70
80
Ver. 0.0
5 / 31
Product Specification
Note) 1. The specified current and power consumption are under the Vcc = 3.3V , 25, fv = 60Hz condition whereas Mosaic pattern is displayed and fv is the frame frequency.
2. This impedance value is needed to proper display and measured form LVDS Tx to the mating connector. 3. The typical operating current is for the typical surface luminance (LWH) in optical characteristics. ILED is the current of each LEDs string, LED backlight has 6 strings on it. 4. The LED power consumption shown above does not include power of external LED driver circuit for typical current condition. 5. The life time is determined as the time at which brightness of LED is 50% compare to that of minimum value specified in table 8.
Ver. 0.0
6 / 31
Product Specification
Symbol
GND VCC VCC V EEDID NC Clk EEDID DATA EEDID RIN 0RIN 0+ GND RIN 1RIN 1+ GND RIN 2RIN 2+ GND CLKINCLKIN+ GND NC NC GND NC NC GND NC NC GND NC NC Ground
Description
Notes
Power Supply, 3.3V Typ. Power Supply, 3.3V Typ. DDC 3.3V power Reserved for supplier test point DDC Clock DDC Data Negative LVDS differential data input Positive LVDS differential data input Ground Negative LVDS differential data input Positive LVDS differential data input Ground Negative LVDS differential data input [LCD Module Rear View] Positive LVDS differential data input Ground Negative LVDS differential clock input Positive LVDS differential clock input Ground No Connect No Connect Ground No Connect No Connect Ground No Connect No Connect Ground No Connect No Connect 30 1 1, Interface chips 1.1 LCD : SW, SW0612B (LCD Controller) including LVDS Receiver 1.2 System : THC63LVD823A or equivalent * Pin to Pin compatible with LVDS 2. Connector 2.1 LCD : FI-XB30SRL-HF11, JAE its compatible. 2.2 Mating : FI-X30M or equivalent. 2.3 Connector pin arrangement
Ver. 0.0
7 / 31
Product Specification
Symbol
FB1 FB2 FB3 FB4 FB5 FB6 NC NC NC Vin Vin Vin
Description
LED Channel 1 Cathode LED Channel 2 Cathode LED Channel 3 Cathode LED Channel 4 Cathode LED Channel 5 Cathode LED Channel 6 Cathode No Connect No Connect No Connect
Notes
Connector FH33-12S-0.5SH, Hirose its compatible.
FPC
1 12
LED Power ( LED Anode) LED Power ( LED Anode) LED Power ( LED Anode)
Ver. 0.0
8 / 31
Product Specification
Description LVDS Differential Voltage LVDS Common mode Voltage LVDS Input Voltage Range
Unit mV V V
Notes -
3-3-2. AC Specification
Description
Symbol tSKEW
LVDS Clock to Data Skew Margin tSKEW LVDS Clock to Clock Skew Margin (Even to Odd) Maximum deviation of input clock frequency during SSC Maximum modulation frequency of input clock during SSC tSKEW_EO FDEV FMOD
Ver. 0.0
9 / 31
Product Specification
RCLK+
RA+/RB+/RC+/RD+/-
R 3 G4 B 5 G7
R2 G3 B4 G6
R1 G2 B3 R7
R0 G1 B2 R6
G0 B 1 DE X
R 5 B 0
R4 G5
R3 G4 B5 G7
R2 G3 B4 G6
R1 G2 B 3 R7
R0 G1 B2 R6
G0 B 1 DE X
R5 B0
R4 G5
VSYNC HSYNC B 7 B6
VSYNC HSYNC B7 B6
Ver. 0.0
10 / 31
Product Specification
DCLK
tCLK
0.5 Vcc
tHP
tWHA
tHFP
Data Enable
Ver. 0.0 Jun. 06, 2008 11 / 31
Product Specification
LSB
B0 0 0 0 1 1 1 0 1 0 0
Black Red Green Basic Color Blue Cyan Magenta Yellow White RED (00) RED (01) RED RED (62) RED (63) GREEN (00) GREEN (01) GREEN ... GREEN (62) GREEN (63) BLUE (00) BLUE (01) BLUE BLUE (62) BLUE (63)
0 1 0 0 0 1 1 1 0 0
Ver. 0.0
12 / 31
Product Specification
90% 10%
0V 10%
T2 Valid Data
T5
T6
T7
0V T4 LAMP ON OFF
Table 7. POWER SEQUENCE TABLE Parameter Min. T1 T2 T3 T4 T5 T6 T7 0.5 0 200 200 0 0 400 Value Typ. Max. 10 50 50 10 (ms) (ms) (ms) (ms) (ms) (ms) (ms) Units
Note) 1. Valid Data is Data to meet 3-3. LVDS Signal Timing Specifications 2. Please avoid floating state of interface signal at invalid period. 3. When the interface signal is invalid, be sure to pull down the power supply for LCD VCC to 0V. 4. LED power must be turn on after power supply for LCD and interface signal are valid.
Ver. 0.0
13 / 31
Product Specification
4. Optical Specification
Optical characteristics are determined after the unit has been ON and stable for approximately 30 minutes in a dark environment at 25C. The values specified are at an approximate distance 50cm from the LCD surface at a viewing angle of and equal to 0. FIG. 1 presents additional information concerning the measurement equipment and method. FIG. 1 Optical Characteristic Measurement Equipment and Method Optical Stage(x,y) LCD Module Pritchard 880 or equivalent
Units
Notes 1
cd/m2 ms
2 3 4
Ver. 0.0
14 / 31
Product Specification
Note) 1. Contrast Ratio(CR) is defined mathematically as Surface Luminance with all white pixels Contrast Ratio = Surface Luminance with all black pixels 2. Surface luminance is the average of 5 point across the LCD surface 50cm from the surface with all pixels displaying white. For more information see FIG 1. LWH = Average(L1,L2, L5) 3. The variation in surface luminance , The panel total variation ( WHITE) is determined by measuring LN at each test position 1 through 13 and then defined as followed numerical formula. For more information see FIG 2.
WHITE =
4. Response time is the time required for the display to transition from white to black (rise time, TrR) and from black to white(Decay Time, TrD). For additional information see FIG 3. 5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For more information see FIG 4. 6. Gray scale specification Gray Level L0 L7 L15 L23 L31 L39 L47 L55 L63 * fV = 60Hz Luminance [%] (Typ)
TBD TBD TBD TBD TBD TBD TBD TBD 100
Ver. 0.0
15 / 31
Product Specification
FIG. 2 Luminance <measuring point for surface luminance & measuring point for luminance variation>
H A
L6 L7
D
L8
L2
L3
L9
L1
L10
Center Point
L4 L5
L11
L12
L13
FIG. 3 Response Time The response time is defined as the following figure and shall be measured by switching the input signal for black and white.
TrR
TrD
white black
Ver. 0.0
16 / 31
Product Specification
5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model LP154WX7. In addition the figures in the next page are detailed mechanical drawing of the LCD. Horizontal Outline Dimension Vertical Thickness Horizontal Bezel Area Vertical Horizontal Active Display Area Vertical Weight Surface Treatment 500g(Max) Glare treatment of the front polarizer 207.0 mm 344.0 0.5mm 222.0 0.5mm 6.5mm (max) 335.0 0.5mm 210.7 0.5mm 331.2 mm
Ver. 0.0
17 / 31
Product Specification
<FRONT VIEW> Note) Unit:[mm], General tolerance: 0.5mm
Ver. 0.0
18 / 31
Product Specification
<REAR VIEW> Note) Unit:[mm], General tolerance: 0.5mm
Ver. 0.0
19 / 31
Product Specification
[ DETAIL DESCRIPTION OF SIDE MOUNTING SCREW ]
Notes : 1. Screw plated through the method of non-electrolytic nickel plating is preferred to reduce possibility that results in vertical and/or horizontal line defect due to the conductive particles from screw surface.
Ver. 0.0
20 / 31
Product Specification
Gap check for securing the enough gap between LCM and System cover.
1.Rear
side of LCM is sensitive against external stress,and previous check about interference is highly needed.
Define
2.In case there is something from system cover comes into the boundary above,mechanical interference may cause the FOS defects. (Eg:Ripple,White spot..) Check if antenna cable is sufficiently apart from T-CON of LCD Module.
Define
NO GOOD
GOOD
1.If system antenna is overlapped with T-CON,it might be cause the noise.
Ver. 0.0 Jun. 06, 2008 21 / 31
Product Specification
LPL Proposal for system cover design. 3 Gap check for securing the enough gap between LCM and System hinge.
1.At
Define
least 2.0mm of gap needs to be secured to prevent the shock related defects.
2.L type of hinge is recommended than I type under shock test. 4 Checking the path of the System wire.
#6
#5
#4
#3
#2
#1
Good
Ok
Bad
1.COF area needs to be handled with care. 2.GOOD Define Wire path design to system side. OK Wire path is located between COFs. BAD Wire path overlapped with COF area.
Jun. 06, 2008 22 / 31
Ver. 0.0
Product Specification
LPL Proposal for system cover design. 5 Using a bracket on the top of LCM is not recommended.
bracket
With bracket
Without bracket
Define
1.Condition without bracket is good for mechanical noise,and can minimize the light leakage from deformation of bracket. 2.The results shows that there is no difference between the condition with or without bracket. Securing additional gap on CNT area..
System cover inner side. User connector area.
A-1
cut
FPC:Flexible Printed Circuit.
Define
1.CNT area is specially sensitive against external stress,and additional gap by cutting on system cover will be helpful on removing the Ripple. 2.Using a thinner CNT will be better. (eg: FPC type)
Jun. 06, 2008 23 / 31
Ver. 0.0
Product Specification
6. Reliability
Environment test condition No. 1 2 3 4 5 6 Test Item High temperature storage test Low temperature storage test High temperature operation test Low temperature operation test Vibration test (non-operating) Shock test (non-operating) Ta= 60C, 240h Ta= -20C, 240h Ta= 50C, 50%RH, 240h Ta= 0C, 240h Sine wave, 10 ~ 500 ~ 10Hz, 1.5G, 0.37oct/min 3 axis, 1hour/axis Half sine wave, 180G, 2ms one shock of each six faces(I.e. run 180G, 2ms for all six faces) 0 ~ 10,000 feet (3,048m) 24Hr 0 ~ 40,000 feet (12,192m) 24Hr Conditions
Altitude
{ Result Evaluation Criteria } There should be no change which might affect the practical display function when the display quality test is conducted under normal operating condition.
Ver. 0.0
24 / 31
Product Specification
7-2. EMC
a) ANSI C63.4 Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electrical Equipment in the Range of 9kHZ to 40GHz. American National Standards Institute(ANSI), 1992 b) C.I.S.P.R Limits and Methods of Measurement of Radio Interface Characteristics of Information Technology Equipment. International Special Committee on Radio Interference. c) EN 55022 Limits and Methods of Measurement of Radio Interface Characteristics of Information Technology Equipment. European Committee for Electrotechnical Standardization.(CENELEC), 1998 ( Including A1: 2000 )
Ver. 0.0
25 / 31
Product Specification
Note 1. YEAR
Year Mark 2001 1 2002 2 2003 3 2004 4 2005 5 2006 6 2007 7 2008 8 2009 9 2010 0
2. MONTH
Month Mark Jan 1 Feb 2 Mar 3 Apr 4 May 5 Jun 6 Jul 7 Aug 8 Sep 9 Oct A Nov B Dec C
b) Location of Lot Mark Serial No. is printed on the label. The label is attached to the backside of the LCD module. This is subject to change without prior notice.
Ver. 0.0
26 / 31
Product Specification
9. PRECAUTIONS
Please pay attention to the followings when you use this TFT LCD module.
Ver. 0.0
27 / 31
Product Specification
9-5. STORAGE
When storing modules as spares for a long time, the following precautions are necessary. (1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature between 5C and 35C at normal humidity. (2) The polarizer surface should not come in contact with any other object. It is recommended that they be stored in the container in which they were shipped.
Ver. 0.0
28 / 31
Product Specification
1/3
Ver. 0.0
29 / 31
Product Specification
2/3
Ver. 0.0
30 / 31
Product Specification
3/3
Ver. 0.0
31 / 31