Sie sind auf Seite 1von 35

www.DataSheet4U.

com Ordering number : ENA0253

Monolithic Linear IC

LA76814
Overview

For NTSC Color Television Sets

VIF/SIF/Y/C/Deflection Implemented in a Single Chip

LA76814 is VIF/SIF/Y/C/Deflection implemented in a single chip for NTSC color television sets.

Functions
VIF/SIF/Y/C/Deflection implemented in a single chip. I2C bus control.

Specifications
Maximum Ratings at Ta = 25C
Parameter Maximum supply voltage Symbol V8 max V43 max Maximum supply current I18 max I25 max Allowable power dissipation Operating temperature Storage temperature Pd max Topr Tstg Ta 65C * Conditions Ratings 7.0 7.0 25 35 1.5 -10 to +65 -55 to +150 Unit V V mA mA W C C

*: When mounted on a 114.376.11.6 mm3 glass epoxy board Operating Ranges at Ta = 25C
Parameter Recommended supply voltage Symbol V8 V43 Recommended supply current I18 I25 Operating supply voltage range V8 op V43 op Operating supply current range I18 op I25 op Conditions Ratings 5.0 5.0 19 27 4.7 to 5.3 4.7 to 5.3 17 to 21 24 to 30 Unit V V mA mA V V mA mA

Any and all SANYO Semiconductor products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO Semiconductor representative nearest you before using any SANYO Semiconductor products described or contained herein in such applications. SANYO Semiconductor assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor products described or contained herein.

D2006 MS PC B8-4870 No.A0253-1/35

www.DataSheet4U.com

LA76814
Ratings min typ max

Electrical Characteristics Ta = 25C, VCC = V8 = V43 = 5.0V, ICC = I18 = 19mA, ICC = I25 = 27mA
Parameter Circuit voltage, current IF supply current RGB supply voltage Horizontal supply voltage Video supply current VIF block Maximum RFAGC voltage Minimum RFAGC voltage RF AGC Delay Pt (@DAC = 0) RF AGC Delay Pt (@DAC = 63) Input sensitivity No-signal video output voltage Sync signal tip level Video output amplitude Video S/N C-S beat level Differential gain Differential phase Maximum AFT output voltage Minimum AFT output voltage AFT detection sensitivity APC pull-in range (U) APC pull-in range (L) SIF block FM detection output voltage FM limiting sensitivity FM detection output f characteristics FM detection output distortion AM rejection ratio SIF S/N de-emph time constant BPF band characteristics AUDIO block Maximum gain Variable range Frequency characteristics Mute Distortion S/N Crosstalk Chroma block ACC amplitude characteristics 1 ACC amplitude characteristics 2 B-Y/Y amplitude ratio Color control characteristics 1 Color control characteristics 2 Color control sensitivity Tint center Tint variable range (+) Tint variable range (-) ACCM1_N ACCM2_N CLRBY CLRMN CLRMM CLRSE TINCEN TINT+ TINTColor MAX/CEN Color MAX/MIN Input: +6dB/0dB 0dB = 40IRE Input: -14dB/0dB 0.8 0.7 80 1.6 30 1 -10 35 -35 1.0 1.0 100 1.8 45 1.4 0 1.2 1.1 150 2.2 70 4 10 deg deg % deg dB %/bit deg deg deg AGMAX ARANGE AF AMUTE ATHD ASN ACT 1kHz, 400mVrms, Vol: MAX DIN.Audio 65 70 70 75 20kHz 1kHz -2.5 60 -3.0 70 0.0 65 0.0 75 0.5 3.0 2.5 dB dB dB dB % dB dB STHD SAMR SSN SNTC SBW FM = 25kHz AM = 30% DIN.Andio 40 57 2.0 61 3.0 1.5 4.0 1.0 % dB dB dB dB SOADJ SLS SF Output -3dB fm = 100kHz -0.5 620 47 55 3.0 mVrms dB dB VRFH VRFL RFAGC0 RFAGC63 Vi VOn VOtip VO S/N IC-S DG DP VAFTH VAFTL VAFTS fPU fPL CW = 80dB, DAC = 0 CW = 80dB, DAC = 63 DAC = 0 DAC = 63 Output-3db No signal CW = 80dB 80dB, AM = 78%, fm = 15kHz CW = 80dB V3.58MHz/V920kHz 80dB, 87.5% Video MOD 80dB, 87.5% Video MOD CW = 80dB, frequency variations CW = 80dB, frequency variations CW = 80dB, frequency variations 4.3 0.0 18.0 1.0 1.0 3.3 1.1 1.9 45 40 43 3.7 1.4 2.0 49 45 5.0 2.0 4.7 0.2 28.0 10.0 10.0 5.0 0.7 38.0 8.5 0.0 85 75 46 4.1 1.7 2.1 9.0 0.3 0.7 Vdc Vdc dB dB dB Vdc Vdc Vp-p dB dB % deg Vdc Vdc mV/kHz MHz MHz I8 V18 V25 I43 V8 = 5V, V3 = 2.5V I18 = 19mA I25 = 27mA I43 = 5V 61.0 8.0 5.0 94.0 mA V V mA Symbol Conditions Unit

Continued on next page.

No.A0253-2/35

www.DataSheet4U.com
Continued from preceding page. Parameter Demodulation output ratio R-Y/B-Y Demodulation output ratio G-Y/B-Y Demodulation angle R-Y/B-Y Demodulation angle G-Y/B-Y Killer operating point APC pull-in range (+) APC pull-in range (-) Residual higher harmonic level B Residual higher harmonic level R Residual higher harmonic level G OSD block OSD Fast SW threshold Red RGB output level Green RGB output level Blue RGB output level Analog OSD R output amplitude gain match Analog OSD G output amplitude gain match Analog OSD B output amplitude gain match RGB output (cutoff drive) block Brightness control Normal Hi brightness (max) Low brightness (min) Cutoff control (Bias control) Resolution Sub-bias control Resolution Drive adjustment Maximum output (R, B) Drive adjustment Maximum output (G) Output attenuation (R, B) Output attenuation (G) Gamma correction Video SW block Video signal input 1DC voltage Video signal input 1AC voltage Video signal input 2DC voltage Video signal input 2AC voltage SVO terminal DC voltage SVO terminal AC voltage VIN1DC VIN1AC VIN2DC VIN2AC SVODC SVOAC RBout0 Gout0 RGB Gout15 (min) (max) Vbias0 Vbias255 Vbiassns Vsbiassns RBout127 BRT0 BRT63 BRT127 BRGB GRGB FSTH ROSDC GOSDC BOSDC RRGB E_CAR_G E_CAR_R ANGRB_N ANGGB_N KILL_N PULIN+_N PULIN-_N E_CAR_B GB_N Symbol RB_N

LA76814
Conditions min R-Y/B-Y_Angle_DAC R-Y/B-Y_Angle_DAC R-Y/B-Y_Angle_DAC = Center R-Y/B-Y_Angle_DAC = Center 0dB = 40IRE 0.80 0.24 95 -130 -41 350 -350 300 300 300 Ratings typ 0.90 0.30 105 -118 -35 max 1.00 0.36 115 -100 -29 deg deg deg deg dB Hz Hz mVp-p mVp-p mVp-p Unit

1.7

2 100 100 100

2.5

V IRE IRE IRE

0.8 0.8 0.8

1 1 1.0

1.2 1.2 1.2

Ratio Ratio Ratio

1.8 15 -25 1.8 2.8

2.15 20 -20 2.2 3.2 4 8 2.5 2.15

2.5 25 -15 2.6 3.6

V IRE IRE V V mV/Bit mV/Bit Vp-p Vp-p

7 3 78

9 5 85

11 7 92

dB dB IRE

2.2

2.5 1

2.8

V Vp-p

2.2

2.5 1

2.8

V Vp-p

1.7 1.7

2 2

2.3 2.3

V Vp-p

Continued on next page.

No.A0253-3/35

www.DataSheet4U.com
Continued from preceding page. Parameter Filter block Chroma trap amount NTSC C-BPF1A (3.08MHz) C-BPF1B (3.88/3.28MHz) C-BPF1C (4.08/3.08MHz) Y-DL TIME1 S-VHS Y-DL TIME3 NTSC Video block Video overall gain (Contrast max) Contrast adjustment Characteristics Sharpness variability range Normal Max Min Sharp16 Sharp31 Sharp0 BKSTmax BKSTTH ClampG RGBBLK BW1 BW3 Normal/max Min/max CONT63 CONT0 CONT127 Ctrap CBP308 CBP03 CBP05 TdY1 TdY3 Symbol

LA76814
Conditions min Ratings typ max Unit

SHARPNESS = 0 Reference: 3.58MHz Reference: 3.28MHz Reference: 3.08MHz FILTER SYS = 100 FILTER SYS = 000

-36.0 -5.0 -2.0 -3.0 300.0 530.0

-26.0 -1.5 0.0 0.0 350.0 580.0

-22.0 0.0 2.0 3.0 400.0 630.0

dB dB dB dB ns ns

9.0 -7.5 -15.0 F = 2.2MHz, FILTER SYS = 0000 F = 2.2MHz, FILTER SYS = 0000 F = 2.2MHz, FILTER SYS = 0000 5.0 9.0 -4.0 20.0 -5.0 95.0 0.1 7.0MHz/100kHz 2.6MHz/100kHz -6.0 -6.0

11.0 -6.0 -12.0 8.0 12.0 -1.0 25.0 0.0 100.0 0.4 -3.0 -3.0

13.0 -4.5 -9.0 11.0 14.0 2.0 30.0 5.0 105.0 0.7 -1.0 -1.0

dB dB dB dB dB dB IRE IRE % V dB dB

Maximum black stretch gain Black stretch threshold (60IRE black) DC transmission amount Horizontal/vertical blanking output level Video frequency characteristics 1 S-VHS Video frequency characteristics 3 NTSC Deflection block Horizontal free-running frequency Horizontal pull-in range Horizontal output pulse width Horizontal output pulse saturation voltage Vertical free-running frequency 60 Horizontal output pulse phase Horizontal position adjustment range Horizontal position adjustment maximum variability width POR circuit operating voltage Horizontal blanking Left @0 Left @7 Right @0 Right @7 Sand castle Pulse crest value H Pulse crest value M1 Pulse crest value L Burst gate pulse Width Phase

fH fH PULL Hduty V Hsat VFR60 HPHCEN HPHrange HPHstep VPOR BLKL0 BLKL7 BLKR0 BLKR7 SANDH SANDM1 SANDL BGPWD BGPPH VXRAY BLKL: 000 BLKL: 111 BLKR: 000 BLKR: 111 5bit

15600 400 36.1 0 262.0 9.5

15734

15850

Hz Hz

37.6 0.2 262.5 10.5 2.2

39.1 0.4 263.0 11.5

s V H s s

200.0 3.70 7500 10800 1800 -1100 5.3 3.7 0.1 3.5 4.9 0.59 4.00 8300 11600 2600 -300 5.6 4.0 0.4 4.0 5.4 0.69 4.30 9100 12400 3400 500 5.9 4.3 0.7 4.5 5.9 0.79

ns V ns ns ns ns V V V s s V

X-ray protection circuit operating voltage

Continued on next page.

No.A0253-4/35

www.DataSheet4U.com
Continued from preceding page. Parameter Vertical screen size compensation Vertical ramp output amplitude NTSC@64 NTSC@0 NTSC@127 Vsnt64 Vsnt0 Vsnt127 Symbol

LA76814
Conditions min Ratings typ max Unit

VSIZE: 1000000 VSIZE: 0000000 VSIZE: 1111111

0.75 0.40 1.05

0.85 0.50 1.20

0.95 0.60 1.35

Vp-p Vp-p Vp-p

High-voltage dependent vertical size correction Vertical size correction @0 Vertical screen position adjustment Vertical ramp DC voltage NTSC@32 NTSC@0 NTSC@63 Vertical linearity @16 @0 @31 Vertical S-shaped @16 correction @0 @31 AKB AKB DC threshold AKBDC 2.2 2.5 2.8 V Vdcnt32 Vdcnt0 Vdcnt63 Vlin16 Vlin0 Vlin31 VScor16 VScor0 VScor31 VDC: 100000 VDC: 000000 VDC: 111111 VLIN: 10000 VLIN: 00000 VLIN: 11111 VSC: 10000 VSC: 00000 VSC: 11110 2.25 1.85 2.65 0.85 1.17 0.57 0.55 0.85 0.36 2.40 2.00 2.80 1.00 1.32 0.72 0.70 1.00 0.51 2.55 2.15 2.95 1.15 1.47 0.87 0.85 1.15 0.66 Vdc Vdc Vdc ratio ratio ratio ratio ratio ratio Vsizecomp VCOMP: 000 0.83 0.88 0.93 ratio

Package Dimensions
unit : mm 3273
47.58 54 28

(4.0)

1.05

3.8 5.0max

0.51min

1.78

0.48

(0.65)

SANYO : DIP54S(600mil)

0.25

27

15.24

13.8

No.A0253-5/35

METAL FILM

0.47F

VCC
24k 1k

330

680k

1F

1F

103 3k

0.01F (M)

100k

3.38

1k

VCO
0.47F 10F 100F 103 16pF

1F

1F

0.47F

1000pF

3k

472F

103

24k

V/C GND 41 40 39 38

HOR GND

54 53 A2C PLL SPLL VIDEO SW BPF TRAP LIM AMP AFT VIDEO DET FM DET IF AGC SW VIF BPF SW VIDEO AMP APC1 CLMP CLMP 52 51 50 49 48 47 46 45 44 43 42

37

36

35

34

33

32

N.C 31

N.C 30

29

BPF

VXO

CW KIL TINT FILTER ADJ X-RAY

HOR VCO

1/256 AOC KIL COLOR CLAMP

LA76814

DELAY LINE PEAKING CORING

DEMO SYNC SEP BLACK STRETOH DC REST OSD FIX GAIN CONTRAST BRIGHT RGB MATRIX OSD SW CLAMP BUS ABL DRIVE/OUT-OFF AKB

HOR C/D

AFC1 VER SEP VER C/D VER RAMP

AFC2

PHASE SHIFTER

Block Diagram and Test Circuit

DC VOL RF AGC 1
IFSW1 223F (M) 103

HOR VCC 6 7
103

4.7k

102

28

FBP

HOR OUT 8 9 10 11 12 13 14
103

10k

100F

103

103

100k 100k

103

103

103

10F

103

3k

0.015F

2k

10k

1.5k

+5V

0.33F (M) 0.33F (M)

15
100 100pF 100

16

17

18

19

20

21

22

23

24

25

26

27

+7.6V

1F

27
100F

(M)

1k

103 (M)

100pF

1k

1k

30k

50

1k

1k

1F

10k 10F

DELAY2 (9US)

1500pF 10k

104

16k

16k

16k

+7.6V

1k

www.DataSheet4U.com

NC

10

12

13

17

18

19

20

21

22

23

24

14A 14B

15A 15B

16A 16B

25

11

9V

LC4528B
1 2 3 4 5 8 9

+7.6V

16

15

14

13

12

11

10

* 103 : 10000pF * M: Indicates a Mylar capacitor

2k 10k WIDTH(12US)

2200pF

NC

No.A0253-6/35
34 32

44A 44B

54

52

51

46

45

43

42A 42B

40

37

29

100k

600

50

75

75

1k

28

www.DataSheet4U.com

LA76814

Test Conditions Ta = 25C, VCC = V8 = V43 = 5.0V, ICC = I25 = 27mA. Circuit voltage, current
Parameter Horizontal supply voltage Symbol HVCC Test point Input signal Test method Apply a current of 27mA to pin 25 and Bus conditions Initial

25
IF supply current I8 No signal

measure the voltage at pin 25. Apply a voltage of 5.0V to pin 43 and measure the incoming DC current [mA]. Apply a voltage of 5.0V to pin 43 and Initial Initial

8
Video/vertical supply current I43

43

measure the incoming DC current [mA].

No.A0253-7/35

www.DataSheet4U.com

LA76814

VIF Block Input Signals and Test Conditions


1. Input signals must all be input to the PIF IN (pin 6) in the Test Circuit. 2. All input signal voltage values are the levels at the VIF IN (pin 6) in the Test Circuit. 3. Signal contents and signal levels.
Input signal SG1 CW Waveform 45.75MHz Conditions

SG2 CW

42.17MHz

SG3 CW

41.25MHz

SG4 CW

Frequency variable

SG5

45.75MHz 87.5% Video Mod. 10-stairstep wave (Subcarrier: 3.58MHz)

SG6

45.75MHz fm = 15kHz, AM = 78%

4. Before measurement, adjust the DAC as follows.


Parameter Video Level DAC Test point SG6, 80dB Input signal Adjustment Set the output level at pin 46 as close to 2.0Vp-p as possible.

46

No.A0253-8/35

www.DataSheet4U.com

LA76814
Symbol VRFH Test point Input signal SG1 80dB SG1 Measure the DC voltage at pin 4. RF.AGC = "111111" Test method Measure the DC voltage at pin 4. Bus conditions RF.AGC = "000000"

VIF Block Test Conditions


Input signal Maximum RF AGC voltage Minimum RF AGC voltage RF AGC Delay Pt (@DAC = 0) (@DAC = 63) Input sensitivity Vi RFAGC63 RFAGC0 VRFL

80dB SG1 Obtain the input level at which the DC voltage at pin 4 becomes 4.5V. SG1 Obtain the input level at which the DC voltage at pin 4 becomes 4.5V. SG6 Using an oscilloscope, observe the level at pin 46 and obtain the input level at which the waveform's p-p value becomes 1.4Vp-p. No signal Set IF AGC = 1 and measure the DC voltage at pin 46. SG1 Measure the DC voltage at pin 46. IF.AGC = 1 RF.AGC = "111111" RF.AGC = "000000"

46
No-signal video output voltage Sync signal tip level VOtip VOn

46

46
Video output amplitude Video S/N S/N VO

80dB SG6 Using an oscilloscope, observe the level at pin 46 and measure the waveforms p-p value. Measure the noise voltage at pin 46 with an RMS voltmeter through a 10kHz to 4.2MHz band-pass filter. Vsn 20Log (1.0/Vsn).

46

80dB SG1

46

80dB

C-S beat level

IC-S

SG1

Input a 80dB SG1 signal and measure the DC voltage (V3) at pin 3. Mix SG1 = 74dB, SG2 = 69dB, and SG3 = 49dB to enter the mixture in the VIF IN. Apply V3 to pin 3 from an external DC power supply. Using a spectrum analyzer, measure the difference between pin 46s 3.58MHz component and 920kHz component.

46

SG2 SG3

Differential gain

DG

SG5

Using a vector scope, measure the level at pin 46.

46
Differential phase DP

80dB SG5 Using a vector scope, measure the level at pin 46.

46
Maximum AFT output voltage Minimum AFT output voltage AFT detection sensitivity VAFTS VAFTL VAFTH

80dB SG4 Set and input the SG4 frequency to 44.75MHz. Measure the DC voltage at pin 10 at that moment. Set and input the SG4 frequency to 46.75MHz. Measure the DC voltage at pin 10 at that moment. Adjust the SG4 frequency and measure frequency deviation f when the DC voltage at pin 10 changes from 1.5V to 3.5V. VAFTS = 2000/f [mV/kHz]

10

80dB SG4

10

80dBz SG4

10

80dBz

APC pull-in range (U), (L)

fPU, fPL

SG4

Connect an oscilloscope to pin 46 and adjust the SG4 frequency to a frequency higher than 45.75MHz to bring the PLL into unlocked mode. (A beat signal appears.) Lower the SG4 frequency and measure the frequency at which the PLL locks again. In the same manner, adjust the SG4 frequency to a lower frequency to bring the PLL into unlocked mode. Lower the SG4 frequency and measure the frequency at which the PLL locks again.

46

80dB

No.A0253-9/35

www.DataSheet4U.com

LA76814

SIF Block (FM block) Input Signals and Test Conditions


Unless otherwise specified, the following conditions apply when each measurement is made. 1. Bus control condition: IF.AGC. = "1" 2. IFSW1 = "ON" 3. Input signals are input to pin 54 and the carrier frequency is 4.5MHz.
Parameter FM detection output voltage Symbol SOADJ Test point Input signal 90dB, fm = 400Hz, FM = 25kHz FM limiting sensitivity FM detection output f characteristics (fm = 100kHz) FM detection output distortion AM rejection ratio SAMR STHD SF SLS fm = 400Hz, Test method Adjust the DAC (FM.LEVEL) to 7 and measure the 400Hz component of the FM detection output at pin 2. SV1[mVrms] Measure the input level (dB) at which the 400Hz component of the FM detection output at pin 2 becomes -3dB relative to SV1. 90dB, Set IFSW1 = "OFF". Measure the FM detection output of pin 2. SV2[mVrms] SF = 20Log (SV1/SV2) [dB] 90dB, Measure the distortion factor of the 400Hz component of the FM detection output at pin 2. Measure the 400Hz component of the FM detection output at pin 2. Assign the measured value to SV3. SV3[mVrms] SAMR = 20Log (SV1/SV2) [dB] SIF.S/N SSN 90dB, Measure the noise level (DIN AUDIO) at pin 2. SV4[mVrms] SSN = 20Log (SV1/SV4) [dB] NT de-emph time constant SNTC 90dB, Measure the 2.12kHz component of the FM detection output at pin 2. SV5[mVrms] SNTC = 20Log (SV1/SV5) [dB] BPF band characteristics SBW 90dB, Set SW: IF1 = "OFF". PIN 9 = 5V Measure the 646kHz component at pin 2. SV6[mVrms] Set the input frequency to 4.65MHz to the input frequency and measure the 496kHz component at pin 2. SV7[mVrms] SBW = 20Log (SV6/SV7) [dB] FM.LEVEL = 7 FM.LEVEL = 7 FM.LEVEL = 7 FM.LEVEL = 7 FM.LEVEL = 7 FM.LEVEL = 7 FM.LEVEL = 7 Bus conditions FM.LEVEL = 7

FM = 25kHz

fm = 100kHz FM = 25kHz

fm = 400Hz, FM = 25kHz 90dB,

fm = 400Hz, AM = 30%

CW

fm = 2.12kHz FM = 25kHz

CW

No.A0253-10/35

www.DataSheet4U.com

LA76814

Audio Block Input Signals and Test Conditions


Unless otherwise specified, the following conditions apply when each measurement is made. 1. Bus control condition: AUDIO.MUTE = "0", AUDIO.SW = "1", VOL.FIL = "0", IF.AGC. = "1" 2. Input 4.5MHz, 90dB and CW at pin 54. 3. Enter an input signal from pin 51.
Parameter Maximum gain Symbol AGMAX Test point Input signal 1kHz, CW Test method Measure the 1kHz component at the pin 1. V1[mVrms] AGMAX = 20Log (V1/400) [dB] Variable range ARANGE 1kHz, CW Measure the 1kHz component at the pin 1. V2[mVrms] ARANGE = 20Log (V1/V2) [dB] Frequency characteristics Mute AMUTE AF 20kHz, CW Measure the 20kHz component at the pin 1. V3[mVrms] AF = 20Log (V3/V1) [dB] 1kHz, CW Measure the 20kHz component at the pin 1. V4[mVrms] AMUTE = 20Log (V1/V4) [dB] Distortion ATHD 1kHz, CW Measure the distortion of the 1kHz component at the pin 1. Measure the noise level (DIN AUDIO) at the pin 1. V5[mVrms] ASN = 20Log (V1/V5) [dB] Crosstalk ACT 1kHz, CW Measure the 1kHz component at the pin 1. V6[mVrms] ACT = 20Log (V1/V6) [dB] VOLUME = "1111111" AUDIO.SW = "0" VOLUME = "1111111" VOLUME = "1111111" VOLUME = "1111111" AUDIO.MUTE = 1 VOLUME = "1111111" VOLUME = "0000000" Bus conditions VOLUME = "1111111"

400mVrms

400mVrms

400mVrms

400mVrms

1
S/N ASN

400mVrms No signal

400mVrms

No.A0253-11/35

www.DataSheet4U.com

LA76814

Chroma input signal:

C-1 40IRE Burst 0 90 180 270 3.58MHz

77IRE signal (L-77) 77 IRE 0 IRE

C-2 40IRE 62.5IRE

Burst

3.58MHz

346

C-3 40IRE 3.48MHz CW (If a frequency is specified, use the specified frequency.) Burst

C-4 40IRE 28 73 118 163 C-5

35s

Burst

3.53MHz Chroma

No.A0253-12/35

www.DataSheet4U.com

LA76814
Symbol ACCM1 Test point Bout Input signal C-1 0dB Test method Measure the output when 0dB is applied to the chroma input and the output amplitude when +6dB is applied to the chroma input and calculate the ratio between them. ACCM1 = 20Log (+6dBdata/0dBdata) Bus conditions

Chroma Block Test Conditions


Parameter ACC amplitude Characteristics 1

21

+6dB

Characteristics 2

ACCM2

Bout

C-1 -14dB

Measure the output when 0dB is applied to the chroma input and the output amplitude when -14dB is applied to the chroma input and calculate the ratio between them.. ACCM2 = 20Log (-14dBdata/0dBdata)

21

B-Y/Y amplitude ratio

CLRBY

YIN: L77

Measure the Y systems output level. V1 Input a signal to the CIN (only sync signal to the YIN) and measure the output level to calculate as follows: CLRBY = 100(V2/V1)+15%

21

C-1:No signal C-2

Color control

Characteristics 1

CLRMN

C-3

Measure the output amplitude V1 at color control MAX mode and output amplitude V2 at color control NOM mode. CLRMN = V1/V2

Color: 1111111 (Max) Color: 1000000 (NOM)

21

Characteristics 2 Color control sensitivity

CLRMM

C-3

Measure the output amplitude V3 at color control MIN mode. CLRMM = 20Log (V1/V3)

Color: 0000000 (Min)

21
CLRSE C-3

Measure the output amplitude V4 at color control 90 mode and output amplitude V5 at color control 38 mode to calculate as follows: CLRSE = 100(V4-V5)/(V252)

Color: 1011010 Color: 0100110

21

Tint center

TINCEN

C-1

Measure each part of the output waveform and calculate the B-Y axis angle.

TINT: 1000000

21

Tint control

MAX

TINMAX

C-1

Measure each part of the output waveform and calculate the B-Y axis angle as follows: TINMAX = B-Y axis angle-TINCEN

TINT: 1111111

21
MIN TINMIN C-1

Measure each part of the output waveform and calculate the B-Y axis angle as follows: TINMIN = B-Y axis angle-TINCEN

TINT: 0000000

21
Tint control sensitivity TINSE C-1

Measure the angle A1 at TINT control 85 mode and angle A2 at TINT control 42 mode. TINSE = (A1-A2)/43

TINT: 1010101 TINT: 0101010 Color: 1000000 Adjustment value in B and R drives: *1

21
Demodulation output ratio R-Y/B-Y RB YIN: L77

Input a signal to YIN and adjust DAC in R and B drives so that the Y output levels at pins 17 and 19 become as close to the level at 18 as possible. (*1) After that, input 0 IRE to YIN and C-3 to CIN. Measure BOUT output amplitude Vb and ROUT output amplitude Vr and calculate RB=Vr/Vb.

19

C-1: No signal

20

YIN: 0 IRE C-3

21
Demodulation output ratio G-Y/B-Y Demodulation angle R-Y/B-Y ANGRB C-1 GB C-3 Measure GOUT output amplitude Vg and calculate GB = Vg/Vb. For the R/B Drive, the adjustment value: *1 applies. Measure each output level of the BOUT and ROUT and calculate the angles of the B-Y axis and R-Y axis. ANGBR = (R-Y angle)-(B-Y angle) Color: 1000000 Adjustment value in B and R drives: *1

20

21

19
Continued on next page.

No.A0253-13/35

www.DataSheet4U.com
Continued from preceding page. Parameter Demodulation angle G-Y/B-Y Killer operating point Chroma VCO free-running frequency fsc output amplitude C_FSC C-1 CVCOF KILL Symbol ANGGB Test point

LA76814
Input signal C-1 Test method Measure each output level of the GOUT and calculate the angle of the G-Y axis. ANGBG = (G-Y angle)-(B-Y angle) C-3 Reduce the input signal until the output level becomes 50mVp-p or less. Measure the input level at that moment. CIN: Measure oscillation frequency f. CVCOF = f-3579545 (Hz) Measure 3.58MHz CW output amplitude at pin 37. Bus conditions

20

21

35

No signal

21

Chroma BPF Block Test Conditions


Parameter Band-pass amplitude characteristic 3.88/3.28 MHz CBP03 C-3 3.08MHz Symbol CBP308 Test point Input signal C-3 Test method Measure V5 output amplitude. Set the chroma frequency (CW) to 3.08MHz and measure V6 output amplitude. CBE308 = 20Log (V6/V5) Measure V7 output amplitude when the chroma frequency (CW) is 3.28MHz and V8 output amplitude when it (CW) is 3.88 MHz. CBE = 20Log (V8/V7) 4.08/3.08 MHz CBP05 C-3 Set the chroma frequency (CW) to 4.08MHz and measure V9 output amplitude. CBE05 = 20Log (V9/V6) FILTER.SYS: 1 C.BYPASS: 0 FILTER.SYS: 1 C.BYPASS :0 Bus conditions FILTER.SYS: 1 C.BYPASS: 0

21

21

21

No.A0253-14/35

www.DataSheet4U.com

LA76814

Video Block Input Signals and Test Conditions


Chroma input signal* chroma or burst signal: 40 IRE Y input signal: 1001RE (714mV) Bus control bit conditions: Initial state

0IRE signal (L-0): NTSC standard signal

PEDESTAL LEVEL H SYNC 4.7s (H/V SYNC: 40IRE: 286mV)

XIRE signal (L-X)

XIRE (X = 0 to 100) 0IRE

CW signal (L-CW)
20IRE CW signal

50IRE

BLACK STRETCH 0IRE signal (L-BK)

50s

100IRE

5s (Point A)

No.A0253-15/35

www.DataSheet4U.com

LA76814

R/G/B IN Input signal


RGB Input signal 1 (0-1)
to each 20s

0.7V 0.35V A B 0.0VDC

RGB Input signal 2 (0-2)

20s

30s

1.0VDC 0.0VDC

First conditions: Pin 13: 5V, Pin 14: GND, Pin 15: GND, Pin 16: GND, Pin 17: GND.

No.A0253-16/35

www.DataSheet4U.com

LA76814
Symbol CONT127 Test point Input signal L-50 CNTHB[Vp-p] CONT127 = 20Log (CNTHB/0.357). L-50 Measure the output signals 50IRE amplitude. CNTCB[Vp-p] CONT63 = 20Log (CNTCB/0.357). L-50 Measure the output signals 50IRE amplitude. CNTLB[Vp-p] CONT0 = 20Log (CNTLB/0.357). L-CW With the input signals continuous wave = 100kHz, measure the output signals continuous wave amplitude. PEAKDC[Vp-p] With the input signals continuous wave = 7MHz, measure the output signals continuous wave amplitude. CW7[Vp-p] BW1 = 20Log (CW7/PEAKDC) Test method Measure the output signals 50IRE amplitude. Bus conditions CONTRAST: 1111111 CONTRAST: 0111111 CONTRAST: 0000000 FILTER SYS: 100 SHARPNESS: 000000

Video Block Test Conditions


Parameter Video overall gain (Contrast max) Contrast adjustment characterist ics Min/ max Video frequency Characteris tics SVHS BW1 CONT0 Normal /max CONT63

21

21

21

21

NTSC

BW3

L-CW

With the input signals continuous wave = 2.5MHz, measure the output signals continuous wave amplitude. CW2.5[Vp-p] BW3 = 20Log (CW2.5/PEAKDC)

FILTER SYS: 0000 SHARPNESS: 000000 FILTER SYS: 000 SHARPNESS: 000000

21

Chroma trap amount

Ctrap

L-CW

With the input signals continuous wave = 3.58MHz, measure the output signals continuous wave amplitude. F00[Vp-p] Ctrap = 20Log (F00/PEAKDC)

21

DC transmission amount

ClampG

L-0

Measure the output signals 0IRE DC level. BRTPL[V]

Brightness: 0000000 CONTRAST: 1111111

21

L-100

Measure the output signals 0IRE DC level: DRVPH[V] and 100IRE amplitude: DRVH[Vp-p]. ClampG = 100 (1+(DRVPH-BRTPL)/DRVH).

Brightness: 0000000 Contrast: 1111111 FILTER SYS: 100

Y-DL TIME

SVHS

TdY1

L-50

Obtain the time difference (the delay time) from when the rise of the input signal's 50IRE amplitude to the output signal's 50IRE amplitude.

21
NTSC TdY3 L-50

Obtain the time difference (the delay time) from when the rise of the input signal's 50IRE amplitude to the output signal's 50IRE amplitude.

FILTER SYS: 000

21
Maximum black stretch gain BKSTmax L-BK

Measure the 0IRE DC level at point A of the output signal in the Black Stretch Defeat (Black Stretch OFF) mode. BKST1[V] Measure the 0IRE DC level at point A of the output signal in the Black Stretch ON mode. BKST2[V] BKSTmax = 250 (BKST1-BKST2)/CNTHB Blk Str DEF: 0

21

Black stretch threshold black (60IRE black)

BKSTTH

L-40

Measure the 40IRE DC level of the output signal in the Black Stretch Defeat ON mode. BKST3[V] Measure the 60IRE DC level of the output signal in the Black Stretch Defeat (Black Stretch OFF) mode. BKST4[V] BKSTTH = 50 (BKST4-BKST3)/CNTHB

Blk Str DEF: 0

21

Continued on next page.

No.A0253-17/35

www.DataSheet4U.com
Continued from preceding page. Parameter Sharpness variability characteri stics Max Sharp31 L-CW Normal Symbol Sharp16 Test point

LA76814
Input signal L-CW Test method With the input signals continuous wave = 2.2MHz, measure the output signals continuous wave amplitude. F00S16 [Vp-p] Calculate Sharp16 = 20Log (F00S16/PEAKDC). With the input signals continuous wave = 2.2MHz, measure the output signals continuous wave amplitude. F00S31 [Vp-p] Calculate Sharp31 = 20Log (F00S31/PEAKDC). Sharpness: 11111 Bus conditions FILTER SYS: 000 Sharpness: 10000

21

Min

Sharp0

L-CW

With the input signals continuous wave=2.2MHz, measure the output signals continuous wave amplitude. F00S0 [Vp-p] Calculate Sharp0 = 20Log (F00S0/PEAKDC).

Sharpness: 00000

Horizontal/vertical blanking output level

RGBBLK

L-100

Measure the DC level (RGBBLK V) for the output signals blanking period.

21

OSD Block Test Conditions When measuring the OSD block, set the bus bit to 63(0111111) for Contrast, 63(0111111) for Brightness.
Parameter OSD Fast SW threshold Red RGB output level ROSDC Symbol FSTH Test point Input signal L-0 Test method Apply voltage to pin 17 and measure the voltage at pin 17 at the point where the output signal switches to the OSD signal. L-50 Measure the output signals 50IRE amplitude. CNTCR [Vp-p] L-0 O-2 Measure the OSD output amplitude. OSDHR [Vp-p] Pin 17: 3.5V Pin 14A: O-2 applied ROSDH = 50(ROSDH /CNTCR) Green RGB output level GOSDC L-50 Measure the output signals 50IRE amplitude. CNTCG [Vp-p] L-0 O-2 Measure the OSD output amplitude. OSDHG [Vp-p] Pin 17: 3.5V Pin 15A: O-2 applied GOSDC = 50(OSDHG/CNTCG) Blue RGB output level BOSDC L-50 Measure the output signals 50IRE amplitude. CNTCB [Vp-p] L-0 O-2 Measure the OSD output amplitude. OSDHB [Vp-p] BOSDC = 50 (OSDHB/CNTCB) Analog OSD R output level L-0 Measure the amplitudes at point A (0.35V portion of the input signal 0-1) and point B (0.7V portion of the input signal 0-1) of the output signal. Assign the measured values to RGBLR Vp-p and RGBHR Vp-p, respectively. Gain match Linearity Analog OSD G output level RRGB LRRGB L-0 RRGB = RGBLR/CNTCR. LRRGB = 100(RGBLR/RGBHR). Measure the amplitudes at point A (0.35V portion of the input signal 0-1) and point B (0.7V portion of the input signal 0-1) of the output signal. Assign the measured values to RGBLG Vp-p and RGBHG Vp-p, respectively. Gain match linearity GRGB LGRGB GRGB = RGBLG/CNTCG. LGRGB = 100(RGBLG/RGBHG). Continued on next page. Pin 17: 3.5V Pin 15A: O-1 applied Pin 17 : 3.5V Pin 14A : O-1 applied Pin 17: 3.5V Pin 16A: O-2 applied Bus conditions Pin 14A: O-2 applied

21

O-2

19

21

21

19

O-1

20

O-1

No.A0253-18/35

www.DataSheet4U.com
Continued from preceding page. Parameter Analog OSD B output level Symbol Test point

LA76814
Input signal L-0 O-1 Test method Measure the amplitudes at point A (0.35V portion of the input signal 0-1) and point B (0.7V portion of the input signal 0-1) of the output signal. Assign the measured values to RGBLB Vp-p and RGBHB Vp-p, respectively. Bus conditions Pin 17: 3.5V Pin 16A: O-1 applied

21

Gain match Linearity

BRGB LBRGB

BRGB = RGBLB/CNTCB. LBRGB = 100(RGBLB/RGBHB).

RGB Output Block (Cutoff, drive block) Test Conditions When measuring the RGB block, set the bus bit to 127(01111111) for Contrast.
Parameter Brightness control Normal Symbol BRT63 Test point Input signal L-0 signals. R output (pin 19) BRTPCR [V] G output (pin 20) BRTPCG [V] Test method Measure the 0IRE DC levels of the RGB output Bus conditions Brightness: 01111111

19

20

B output (pin 21) BRTPCB [V] BRT63 = (BRTPCR+BRTPCG+BRTPCB)/3.

21
Max BRT127 Measure the 0IRE DC level of the output signal of Brightness: 1111111

21

B output (21). BRTPHB [V] BRT127 = 50(BRTPHB-BRTPCB)/CNTHB.

Min

BRT0

Measure the 0IRE DC level of the output signal of B output (21). BRTPHB [V] BRT0 = 50(BRTPLB-BRTPCB)/CNTHB.

Brightness: 0000000

Bias (cutoff) control

Min

Vbias0

L-50

Measure the 0IRE DC levels of the RGB output signals. R output (pin 19) Vbias0R [V] G output (pin 20) Vbias0G [V]

Sub-Brightness: 0000000

19

20
Max Vbias255

B output (pin 21) Vbias0B [V] Measure the 0IRE DC levels of the RGB output Sub-Brightness: 1111111 Red/Green/Blue Bias: 11111111 Red/Green/Blue Bias:01010000 signals. R output (pin 19) Vbias255R [V] G output (pin 20) Vbias255G [V] B output (pin 21) Vbias255B [V]

21

Bias (cutoff) control resolution

Vbiassns

Measure the 0IRE DC levels of the RGB output signals. R output (pin 19) BAS80R [V] G output (pin 20) BAS80G [V] B output (pin 21) BAS80B [V] Measure the 0IRE DC levels of the RGB output signals. R output (pin 19) BAS48R [V] G output (pin 20) BAS48G [V] B output (pin 21) BAS48B [V] Vbiassns* = (BAS80*-BAS48*)/32 *: R, G, B

Red/Green/Blue Bias: 00110000

Sub-bias control resolution

Vsbiassns

L-50

Measure the 0IRE DC levels of the RGB output signals. R output (pin 19) SBTPMR [V] G output (pin 20) SBTPMG [V] B output (pin 21) SBTPMB [V] Vsbiassns* = (BRTPC*-SBTPM*) *: R, G, B

Sub-Brightness: 0101010 Contrast: 0111111

Continued on next page.

No.A0253-19/35

www.DataSheet4U.com
Continued from preceding page. Input signal Drive adjustment maximum output Symbol RBout127 Gout15 Test point

LA76814
Input signal L-100 signals. R output (pin 19) DRVHR [Vp-p] B output (pin 21) DRVHB [Vp-p] Test method Measure the 100IRE amplitude of the R, B output Bus conditions Brightness: 0000000

19

20

Measure the 0IRE DC levels of the G output signals. G output (pin 20) DRVHG [Vp-p] Measure the 100IRE amplitude of the R, B output signals. R output (pin 19) DRVLR [Vp-p] B output (pin 21) DRVLB [Vp-p] Measure the 0IRE DC levels of the G output signals. G output (pin 20) DRVHG [Vp-p] RBout0* = 20Log (DRVH*/DRVL*) Gout0* = 20Log (DRVH*/DRVL*) Brightness: 0000000 Red/Blue Drive: 0000000

Output attenuation

RBout0 Gout0

21

Gamma correction

R G B

L-100

Measure the 100IRE amplitude of the RGB output signals with Gamma Def being ON and OFF. *A, *B [Vp-p]

Gamma Def: Off, On B Gamma sel: 11, 00

19

20

* = 100*(*A/*B) * : R, G, B

21

VIDEO SW Block Test Conditions When measuring the VIDEO SW block, set the bus bit to 63(0111111) for Contrast, 63(0111111) for Brightness.
Input signal Video signal input 1DC voltage Video signal input 2DC voltage SVO terminal DC voltage SVO terminal AC voltage SVOAC SVODC SVODC Symbol VIN1DC Test point Input signal L-100 the pedestal. L-100 Input signals to pin 44 and measure the voltage of the pedestal. L-100 Input signals to pin 42 and measure the voltage of the pedestal at pin 40. L-100 Input signals to pin 42 and measure the voltage of the pedestal at pin 40. VIDE0 SW: 1 VIDEO SW: 1 VIDEO SW: 0 Test method Input signals to pin 42 and measure the voltage of Bus conditions VIDEO SW: 1

42

44

40

40

No.A0253-20/35

www.DataSheet4U.com

LA76814

Deflection Block Input Signals and Test Conditions


Unless otherwise specified, the following conditions apply when each measurement is made. 1. VIF, SIF blocks: No signal 2. C input: No. signal 3. Sync input: A horizontal/vertical composite sync signal NTSC: 40IRE, horizontal sync signal (15.734264kHz) and vertical sync signal (59.94kHz) Note: No burst signal, chroma signal shall exist below the pedestal level. Signal unsuitable for Y input

Signal suitable for Y input

Chroma signal Burst signal

4. Bus control conditions: Initial conditions unless otherwise specified. 5. The delay time from the rise of the horizontal output (pin 27 output) to the fall of the FBP IN (pin 28 input) is 9s. 6. Pin 13 (ABL input, vertical size correction circuit input terminal) is connected to VCC (5.0V).

No.A0253-21/35

www.DataSheet4U.com

LA76814
Symbol fH Test point Input signal Y IN: No signal YIN: Test method Connect a frequency counter to the output of pin 27 (H out) and measure the horizontal free-running frequency. Using an oscilloscope, monitor the horizontal sync signal which is input to the Y IN (pin 42) and the pin 27 output (H out) and vary the horizontal signal frequency to measure the pull-in range. Measure the voltage for the pin 27 horizontal output pulses low-level period. Bus conditions

Deflection Block Test Conditions


Input signal Horizontal free-running frequency Horizontal pull-in range fH PULL

27

42

Horizontal/ vertical sync signal

Horizontal output pulse length

Hduty

Y IN:

27

Horizontal/ vertical sync signal

Horizontal output pulse saturation voltage

V Hsat

Y IN:

Measure the voltage for the pin 27 horizontal output pulses low-level period.

27

Horizontal/ vertical sync signal

Vertical free-running period 60 (NTSC)

VFR60

Y IN:

Measure the vertical output period T at pin 23 T15.734kHz

CDMODE: 0

23

No signal

Vertical output 2.5V T

Horizontal output pulse

HPHCEN

Y IN:

Measure the delay time from to the rise of the pin 27 horizontal output pulse to the fall of the Y IN horizontal sync signal.

27

Horizontal/ vertical sync signal

42

HPHCEN

20IRE

2.5V Horizontal output


Horizontal position adjustment range HPHrange Y IN: With H PHASE: 0 and 31, measure the delay time from the rise of the pin 27 horizontal output pulse to the fall of the Y IN horizontal sync signal and calculate the difference from H PHCEN. H PHASE: 00000 H PHASE: 11111

27

Horizontal/ vertical sync signal

42

Measuring HPHCEN

20IRE

2.5V Horizontal output

Continued on next page.

No.A0253-22/35

www.DataSheet4U.com
Continued from preceding page. Input signal Horizontal position adjustment maximum variable width Symbol HPHstep Test point

LA76814
Input signal Y IN: Horizontal/ vertical sync signal Test method With H PHASE: 0 to 31 varied, measure the delay time from to the rise of the pin 27 horizontal output pulse to the fall of the Y IN horizontal sync signal and calculate the variation at each step. Retrieve data for maximum variation. to H PHASE: 11111 Bus conditions H PHASE: 00000

27

42

Measuring HPHCEN

20IRE

Horizontal output

POR circuit operating voltage

VPOR

Y IN:

Connect a DC power supply in place of the current source to pin 25 and gradually decrease the voltage from 5.0V until the BUS READ TATUS [POR][STATUS1 (DA01) becomes "1". Measure the DC voltage at pin 28 at the moment. Measure the time T from the left end of Hsync at pin 42 Y IN to the left end of blanking at pin 21 BlueOUT with BLKL = 000. BLKL: 000

25

Horizontal/ vertical sync signal

Horizontal blanking left variable range

@0

BLKL0

Y IN:

21

Horizontal/ vertical sync signal

42

Y IN

Hsync

Blue OUT

@7

BLKL7

Measure the time T from the left end of Hsync at pin 42 Y IN to the left end of blanking at pin 21 BlueOUT with BLKL = 111.

BLKL: 111

Y IN

Hsync

Blue OUT

Continued on next page.

No.A0253-23/35

www.DataSheet4U.com
Continued from preceding page. Input signal Horizontal blanking right variable range @0 Symbol BLKR0 Test point

LA76814
Input signal Y IN: Test method Measure the time T from the left end of Hsync at pin 42 Y IN to the left end of blanking at pin 21 BlueOUT with BLKR = 000. Bus conditions BLKR: 000

21

Horizontal/ vertical sync signal

Y IN

Hsync

42

Blue OUT

@7

BLKR7

Measure the time T from the left end of Hsync at pin 42 Y IN to the left end of blanking at pin 21 BlueOUT with BLKR = 111.

BLKR: 111

Y IN

Hsync

Blue OUT

Sand castle pulse crest value

SANDH

Y IN:

Measure the supply voltage at point H of the pin 28 FBP IN wave form for Hsync period.

28

Horizontal/ vertical sync signal

M1

SANDM1

Measure the supply voltage at point M1 of the pin 28 FBP IN wave form for Hsync period.

M1

SANDL

Measure the supply voltage at point L of the pin 28 FBP IN wave form for Hsync period.

L
Burst gate pulse length BGPWD Y IN: Measure the BGP width T of the pin 28 FBP IN wave form for Hsync period.

28

Horizontal/ vertical sync signal

Continued on next page.

No.A0253-24/35

www.DataSheet4U.com
Continued from preceding page. Input signal Burst gate pulse I phase Symbol BGPPH Test point

LA76814
Input signal Y IN: Horizontal/ vertical sync signal Test method Measure the time from the left end of Hsync at pin 42 Y IN to the left end of the pin 28 FBP IN wave form for Hsync period. Bus conditions

28

Hsync Y IN

42

FB PIN

X-ray protection circuit operating voltage

VXRAY

Y IN:

Connect a DC power supply to pin 34 and gradually increase the voltage from 0V until the pin 27 horizontal output pulse ceases. Measure the DC voltage at pin 34 at that moment.

27

Horizontal/ vertical sync signal

34

Vertical Screen Size Correction


Input signal Vertical ramp output Amplitude @64 Symbol Vsnt64 Test point Input signal Y IN: Horizontal/ vertical sync signal Test method Monitor the pin 23 vertical ramp output and measure the voltage at line 22 and line 262. Calculate as follows: Vspal64 = Vline262-Vline22 Vertical ramp output Bus conditions

23

Line 262 Line 22 @0 Vsnt0 Monitor the pin 23 vertical ramp output and measure the voltage at line 22 and line 262 Calculate as follows: Vspal64 = Vline262-Vline22 Vertical ramp output VSIZE: 0000000

Line 262 Line 22 @127 Vsnt127 Monitor the pin 23 vertical ramp output and measure the voltage at line 22 and line 262 Calculate as follows: Vspal64 = Vline262-Vline22 Vertical ramp output VSIZE: 1111111

Line 262 Line 22 .

No.A0253-25/35

www.DataSheet4U.com

LA76814
Symbol Vsizecomp Test point Input signal Y IN: Horizontal/ vertical sync signal Test method Monitor the pin 23 vertical ramp output and measure the voltage at the line 22 and line 262 with VCOMP = 000. Calculate as follows: Va = Vline262-Vline22 Apply 4.0V to pin 11 and measure the voltage at the line 22 and line 262 again. Calculate as follows: Va = Vline262-Vline22 Calculate as follows: Vsizecomp = Vb/Va Vertical ramp output Bus conditions VCOMP: 000

High-voltage Dependent Vertical Size Correction


Input signal Vertical size correction @0

23

Line 262 Line 22

Vertical screen position adjustment


Input signal Vertical ramp DC voltage @32 Symbol Vdcnt32 Test point Input signal Y IN: Horizontal/ vertical sync signal Vertical ramp output Test method Monitor the pin 23 vertical ramp output and measure the voltage at line 142. Bus conditions

23

Line 142

@0

Vdcnt0

Monitor the pin 23 vertical ramp output and measure the voltage at line 142. Vertical ramp output

VDC: 000000

Line 142

@63

Vdcnt63

Monitor the pin 23 vertical ramp output and measure the voltage at line 142. Vertical ramp output

VDC: 111111

Line 142 Continued on next page.

No.A0253-26/35

www.DataSheet4U.com
Continued from preceding page. Input signal Vertical linearity @16 Symbol Vlin16 Test point

LA76814
Input signal Y IN: Horizontal/ vertical sync signal Test method Monitor the pin 23 vertical ramp output and measure the voltage at line 22, line 142 and 262. Assign the respective measured values to Va, Vb and Vc. Calculate as follows: Vlin16 = (Vb-Va)/(Vc-Vb) Vertical ramp output Line 262 Bus conditions

23

Line 142 Line 22 @0 Vlin0 Monitor the pin 23 vertical ramp output and measure the voltage at line 22, line 142 and 262. Assign the respective measured values to Va, Vb and Vc. Calculate as follows: Vlin0 = (Vb-Va)/(Vc-Vb) Vertical ramp output Line 262 VLIN: 00000

Line 142 Line 22 @31 Vlin31 Monitor the pin 23 vertical ramp output and measure the voltage at line 22, line 142 and 262 with vLIN = 11111. Assign the respective measured values to Va, Vb and Vc. Calculate as follows: Vlin31 = (Vb-Va)/(Vc-Vb) Vertical ramp output Line 262 VLIN: 11111

Line 142 Line 22

Continued on next page.

No.A0253-27/35

www.DataSheet4U.com
Continued from preceding page. Input signal Vertical S-shaped correction @16 Symbol VScor16 Test point

LA76814
Input signal Y IN: Horizontal/ vertical sync signal Test method Monitor the pin 23 vertical ramp output and measure the voltage at line 32, line 52, line 132, line 152, line 232 and 252. Assign the respective measured values to Va, Vb, Vc, Vd, Ve and Vf. Calculate as follows: VScor16 = 0.5((Vb-Va)+(Vf-Ve))/(Vd-Vc) Line 252 Vertical ramp output Line 232 Line 52 Line 152 Line 132 Line 32 Bus conditions VS: 10000

23

@0

VScor0

Monitor the pin 23 vertical ramp output and measure the voltage at the line 32, line 52, line 132, line 152, line 232 and line 252 with VSC = 000. Assign the respective measured values to Va, Vb, Vc, Vd, Ve and Vf. Calculate as follows: VScor0 = 0.5((Vb-Va)+(Vf-Ve))/(Vd-Vc) Line 252 Vertical ramp output Line 232 Line 52 Line 152 Line 132 Line 32

@31

VScor31

Monitor the pin 23 vertical ramp output and measure the voltage at line 32, line 52, line 132, line 152, line 232 and line 252 with VSC = 000. Assign the respective measured values to Va, Vb, Vc, Vd, Ve and Vf. Calculate as follows: Vscor31 = 0.5((Vb-Va)+(Vf-Ve))/(Vd-Vc) Line 252 Vertical ramp output Line 232 Line 52 Line 152 Line 132 Line 32

VSC: 11111

AKB DC threshold

AKBDC

Y IN:

Increase the DC voltage applied at pin 22 from 2.0V to 3.0V gradually and measure the DC voltage at pin 22 when BUS READ STATUS, [AKB (R, G, B)] and [STATUS2 (DA01, DA02, DA03)] become (1, 1, 1).

22

Horizontal/ vertical sync signal PAL or NTSC

No.A0253-28/35

www.DataSheet4U.com

LA76814

Control Register Bit Allocation Map


Control Register Bit Allocations Sub Address 00000000 MSB DA0 ON/OFF 1 00001 H BLK SW 0 00010 Sync.Kill 0 00011 VSEPUP 0 00100 Gray Mode 0 00101 H BLK R&L 1 00110 V.TEST 0 00111 R.BIAS 0 01000 G.BIAS 0 01001 B.BIAS 0 01010 * (0) 01011 Drive.Test 0 01100 * (0) 01101 Blank.Def 0 01110 * (0) 01111 * (0) 10000 OSD Cnt.Test 0 10001 Blk.Str.Deff 1 10010 Tint.Test 0 10011 Color.Test 0 10100 Video SW 0 10101 AKB B/W 0 10110 * (0) 10111 AKB Test 0 0 Color 1 Trap.Test 1 AKB Def 0 FBPBLK.SW 1 0 C.Temp.R 1 C.TEMP.G 1 C.TEMP.B 1 0 0 0 0 0 Continued on next page. 0 0 0 0 0 0 0 0 0 0 0 0 0 0 * (0) 0 Filter.Sys 0 * 0 0 0 Tint 1 0 0 0 0 0 0 0 R.DRIVE 1 B Select 0 B.DRIVE 1 Sub.Bright 1 Bright 1 Contrast 1 * (0) Coring 1 0 * (0) Sharpness 0 0 0 0 0 0 0 * (0) 0 * (0) 0 * (0) 0 OSD Contrast 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 1 1 RG Def 1 1 G.DRIVE 1 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 V.COMP 1 1 1 DA1 AFC gain&gate 0 Audio.Mute 0 V.SIZE 1 V.KILL 0 Cross B/W 0 0 V.SC 0 0 0 COUNT.DOW N.MODE 0 0 * (0) 0 * (0) 0 V.POSI 1 V.LIN 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 DA2 H.FREQ 1 Video.Mute 0 1 H.PAHSE 1 0 0 0 0 1 1 1 1 DA3 DATA BITS DA4 DA5 DA6 LSB DA7

No.A0253-29/35

www.DataSheet4U.com
Continued from preceding page. Sub Address DA0 00011000 * 0 11001 Cont.Test 0 11010 * (0) 11010 * (0) 11100 Audio SW 0 11101 FM.Test 0 11110 FM.Mute 0 11111 VIDEO.LEVEL 1 0 0 DA1 C.Ext 0 Digital OSD 0 * (0) * (0) Volume 0 VOL.FIL 0 * (0) 0 RF.AGC 1 * (0) MSB DA2 C.Bypass 1 Brt.Abl.Def 0 * (0) * (0)

LA76814
DATA BITS DA3 C_Kill ON 0 Mid.Stp.Def 0 * (0) * (0) DA4 C_Kill OFF 0 Emg.Abl.Def 0 R-Y/B-Y Angle 1 * (0) 0 * (0) 0 * (0) 0 * (0) DA5 * (0) Bright.Abl.Threshold 1 0 0 DA6 * (0) LSB DA7 * (0)

0 VIF.Sys.SW 0 FM.LEVEL 1

0 * (0)

0 * (0)

0 * (0)

0 IF.AGC 0

Status Register Bit Allocations


MSB DA0 2nd Byte X.Ray * 3rd Byte H.Lock * AKB R G B DA1 POR * DA2 * (0) DA3 RF.AGC * DA4 IF.LOCK * * (0) DATA BITS DA5 V.TRI * * (0) DA6 * (0) * (0) LSB DA7 ST/NONST * * (0)

No.A0253-30/35

www.DataSheet4U.com

LA76814
0 HEX OFF (Tset Enable) Auto (Gain) Auto (Gate) Right Control Active Active Sync active normal Vrt active Normal Normal Normal Auto Mode Normal B Gamma on 85% (same as R, G) RG Gamma on Blanking Normal Blk Str On Core Off Normal Normal Internal Mode AKB Black AKB On FBP not or Normal Internal Mode Bypass OFF Auto Mode Auto Mode Normal Analogue Emg On Brt ABL On Mid Stp On Internal Mode Normal Normal Active 45.75MHz AGC active 1 HEX ON (Test Disable) Gain: Fast Non-Gate Left Control Mute Mute Sync killed Vsepup Vrt killed Gray OSD Black Vrt S Corr non standard Test Mode B Gamma on 90% RG Gamma off No Blank Test Mode Blk Str Off Core On Test Mode Test Mode External Mode AKB White AKB Off FBP or Test Mode1 External Mode Bypass ON Killer ON Killer OFF Test Mode Digital Emg Off Brt ABL Off Mid Stp Off External Mode Test Mode Filte OFF Mute 58.75MHz AGC defeat Test Mode2 Test Mode3 B Gamma on 95% B Gamma off White Vrt Lin Cross Vrt Size 2 HEX 3 HEX

Control Register Truth Table


Register Name ON/OFF (T.Disable) AFC gain&gate H BLK SW Audio.Mute Video.Mute Sync.Kill Vsepup V.KILL Gray Mode Cross B/W Vertical Test Count down mode Drive.Test B Gamma Select R/G Gamma. Def Blank.Def OSD Cnt.Test Blk.Str.Deff Coring Tint.Test Color.Test Video.SW AKB B/W AKB Def FBPBLK.SW AKB Test C.Ext C.Bypass C_Kill ON C_Kill OFF Cont.Test Digital OSD Emg.Abl.Def Brt.Abl.Def Mid.Stp.Def Audio.SW FM.Test VOL.FIL FM.Mute VIF.Sys.SW IF.AGC

Filter System
Y Filter 0 HEX 1 HEX 2 HEX 3 HEX 4 HEX 5 HEX 6 HEX 7 HEX 3.58MHz Trap 3.58MHz Trap 3.58MHz Trap 3.58MHz Trap No Trap (Wide Band mode) No Trap (Wide Band mode) No Trap (Wide Band mode) No Trap (Wide Band mode) Chroma Filter Peaked 3.58MHz BPF Symmetrical 3.58MHz BPF Peaked 3.58MHz BPF Symmetrical 3.58MHz BPF Peaked 3.58MHz BPF Symmetrical 3.58MHz BPF Peaked 3.58MHz BPF Symmetrical 3.58MHz BPF

No.A0253-31/35

www.DataSheet4U.com

LA76814
0 HEX Undetected Undetected RF.AGC.OUT = "L" Lock V.Triger Undetected Non-Standard Horiz Unlocked R Beam Current Low G Beam Current Low B Beam Current Low 1 HEX Detected Detected RF.AGC.OUT = "H" Unlock V.Triger Detected Standard Horiz Locked R Beam Current High G Beam Current High B Beam Current High

Status Byte Truth Table


Register X.RAY POR RF.AGC IF.LOCK V.TRI ST/NONST H.LOCK AKB R AKB G AKB B

Initial Conditions
Initial Test Conditions Register ON/OFF (T.Disable) AFC gain&gate H.FREQ H BLK SW Audio.Mute Video.Mute H.PHASE Sync.Kill V.SIZE VSEPUP V.KILL V.POSI Gray Mode Cross B/W V.LIN H BLK R&L V.SC V.TEST V.COMP COUNT.DOWN.MODE R.BIAS G.BIAS B.BIAS R.DRIVE Drive.Test B Gamma Select R/G Gamma.Def G.DRIVE B.DRIVE Blank.Def Sub.Bright Bright Contrast 1 HEX 0 HEX 3F HEX 0 HEX 0 HEX 0 HEX 10 HEX 0 HEX 40 HEX 0 HEX 0 HEX 20 HEX 0 HEX 0 HEX 10 HEX 4 HEX 00 HEX 0 HEX 7 HEX 0 HEX 00 HEX 00 HEX 00 HEX 7F HEX 0 HEX 0 HEX 1 HEX 8 HEX 7F HEX 0 HEX 40 HEX 40 HEX 40 HEX OSD Cnt.Test OSD Contrast Blk.Str.Deff Coring Sharpness Tint.Test Tint Color.Test Color Video.SW Trap.Test Filter.Sys AKB B/W AKB Def C.Temp.R FBPBLK.SW C.Temp.G AKB Test C.Temp.B C.Ext C.Bypass C_Kill ON C_Kill OFF Cont.Test Digitsl OSD Bright.Abl.Threshold Emg.Abl.Def Brt.Abl.Def Mid.Stp.Def R-Y/B-Y Angle Audio.SW Volume FM.Test VOL.FIL RF.AGC FM.Mute VIF.Sys.SW IF.AGC VIDEO.LEVEL FM.LEVEL Initial Test Conditions (continued) Register 0 HEX 0 HEX 1 HEX 1 HEX 00 HEX 0 HEX 40 HEX 0 HEX 40 HEX 0 HEX 4 HEX 0 HEX 0 HEX 0 HEX 20 HEX 1 HEX 20 HEX 0 HEX 20 HEX 0 HEX 1 HEX 0 HEX 0 HEX 0 HEX 0 HEX 4 HEX 0 HEX 0 HEX 0 HEX 8 HEX 0 HEX 00 HEX 0 HEX 0 HEX 20 HEX 0 HEX 0 HEX 0 HEX 4 HEX 10 HEX

No.A0253-32/35

www.DataSheet4U.com

LA76814
Bits 1 1 6 1 1 1 5 1 7 1 1 6 1 2 5 3 5 2 3 1 8 8 8 7 1 2 1 4 7 1 7 7 7 1 2 1 1 6 1 7 1 7 1 3 3 1 1 6 1 6 2 6 General Description Enable the horizontal output & Disable the Test SW & enable Audio/Video Mute SW Select horizontal first loop gain & H-sync gating on/off Align ES Sample horizontal frequency Blanking Control (Right/Left) Disable audio outputs Disable video outputs Align sync to flyback phase Force free-run mode Align vertical amplitude Select vertical sync. separation sensitivity Disable vertical output Align vertical DC bias OSD Gray Tone Enable Service Test Mode (normal/Black/White/Cross) Align vertical linearity H-Blanking Control (Width/Phase) Align vertical S-correction Select vertical DAC test modes Align vertical size compensation Select vertical countdown mode Align Red OUT DC level Align Green OUT DC level Align Blue OUT DC level Align Red OUT AC level Enable Drive control DAC test modes Select Blue Gamma Gain Disable R/G Gamma Correction Align Green OUT AC level Align Blue OUT AC level Disable RGB output blanking Align common RGB DC level Customer brightness control Customer contrast control Enable OSD Contrast DAC test mode Align OSD AC level Disable black stretch Enable luminance coring Customer sharpness control Enable tint DAC test mode Customer tint control Enable color DAC test mode Customer color control Select Video source Trap Test Select Y/C Filter mode Select AKB Black or White Disable AKB circuits Align AKB color temperature Enable RGB Blanking or FBP Align AKB color temperature Enable AKB C Temp. DAC test mode Align AKB color temperature Continued on next page.

Control Register Descriptions


Register Name ON/OFF (T Disable) AFC Gain & gate H Freq. H.BLK.SW Audio Mute Video Mute H PHASE Sync Kill Vertical Size Vsep.up Vertical Kill V POSI (Vertical DC) Gray Mode Cross B/W V LIN (Vertical Linearit) H BLK R&L Vertical S-Correction Vertical Test Vertical Size Compensation Count Down Mode Red Bias Green Bias Blue Bias Red Drive Drive Test B Gamma Select R/G Gamma Defeat Green Drive Blue Drive Blank Def Sub Brightness Brightness Control Contrast Control OSD Contrast Test OSD Contrast Control Blk Str Def Coring Enable Sharpness Control Tint Test Tint Control Color Test Color Control Video SW Trap.Test Filter System AKB B/W AKB Def C Temp R FBPBLK.SW C Temp G AKB Test C Temp B

No.A0253-33/35

www.DataSheet4U.com
Continued from preceding page. Register Name AutoFlesh C Ext C Bypass C Kill On C Kill Off Cont Test Bright ABL Threshold Emergency ABL Defeat Bright ABL Defeat Bright Mid Stop Defeat Digital OSD R-Y/B-Y Angle Audio SW Volume Control FM.Test Volume Filter Defeat RF AGC Delay FM Mute VIF System SW IF AGC Defeat Video Level FM Level

LA76814
Bits 1 1 1 1 1 1 3 1 1 1 1 4 1 7 1 1 6 1 1 1 3 5 General Description Enable AutoFlesh function Selected-C In SW on Select Chroma BPF bypass C Kill Mode (1: Enable Killer circuit) Disable Killer circuit Enable contrast DAC test mode Align brightness ABL threshold Disable emergency brightness ABL Disable brightness ABL Disable brightness mid stop Select Digital/Analogue OSD R-Y/B-Y Angle Select Audio source Customer volume control FM.Test Disable volume DAC filter Align RF AGC threshold Disable FM outputs Select 38.9/39.5/38.0/45.75/58.75 Disable IF and RF AGC Align IF video level Align WBA output level

Pin Assignment
PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Audio Output FM Output PIF AGC RF AGC Output PIF Input1 PIF Input2 IF Ground IF VCC FM Filter AFT Output Bus Data Bus Clock ABL Red Input Green Input Blue Input Fast Blanking Input RGB VCC Red Output Green Output Blue Output B.AKB Input Vertical Output Ramp ALC Filter Horizontal/BUS VCC Horizontal AFC Filter Horizontal Output FUNCTION PIN 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 SIF Input SIF APC Filter SIF Output Ext. Audio Input FLL Filter VCO Coil 1 VCO Coil 2 APC Filter Video Output Black Level Detector Internal Video Input (S-C IN) Video/Vertical VCC External Video Input (Y IN) Video/Vertical/BUS Ground Selected Video Output ACC Filter 3.58MHz Crystal fsc (3.58MHz) Output Chroma APC Filter KILLER Filter XRAY Horizontal Ground OSD Contrast NC NC VCO IREF Flyback Pulse Input FUNCTION

No.A0253-34/35

www.DataSheet4U.com

LA76814

Specifications of any and all SANYO Semiconductor products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Semiconductor Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor products (including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Semiconductor Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO Semiconductor believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties.
This catalog provides information as of December, 2006. Specifications and information herein are subject to change without notice. PS No.A0253-35/35

Das könnte Ihnen auch gefallen