Sie sind auf Seite 1von 8

Technical Description PR 712 B

litronic`
Crawler Tractor

Engine output 77 kW / 105 HP


Operating weight 11.8 – 13.6 t / 26,000 – 30,000 lb
Hydrostatic travel drive with electronic steering control

The Better Machine.


Engine Travel Control
Liebherr-Diesel Engine ____ D 924 T-E 1 joystick lever __________ with electronic control for all travel
Rating per functions: travel direction, speed, steering
ISO 9249 ________________________ 77 kW (105 HP) at 2000 RPM and counter-rotation
Displacement __________________ 6.7 l (409 cu.in.) Speed range 1 ____________ 0 – 5 km/h (0 to 3.1 mph)
Bore/Stroke ____________________ 122/142 mm (4.8/5.6 in.) Speed range 2 ____________ 0 – 11 km/h (0 to 6.9 mph)
Design ____________________________ 4 cylinder in-line engine, water-cooled, Engine speed
turbocharged sensing control __________ electronic regulation assures constant
Injection ________________________ direct fuel injection with injection pump, balance between travel speed and necessary
mechanical govenor drawbar pull through engine speed sensing
Fuel filter ________________________ pre-cleaner with water separator and fine avoiding engine overload, even in partial
filters load range
Lubrication ____________________ pressurized lube system with full flow fil- Straight line travel ____ electronically controlled
ter and integrated oil cooler, deep oil pan Parking/emergency
for inclinations, engine lubrication to an brake ________________________ automatically applied after the joystick lever
inclination of up to 45h to each side is put in neutral position
Operating voltage ____________ 24 V Safety lever ______________ inactivates complete travel and working
Alternator ______________________ 55 Amp. hydraulic circuit and automatically activates
Starter ____________________________ 5.4 kW (7 HP) parking brake
Central fuse box ______________ 35 A Emergency shut off ____ push button on instrument panel immediately
Batterie __________________________ 110 Ah activates parking and emergency brake

Implement Hydraulic
Travel Drive Hydraulic system ______ load sensing proportional pump flow control,
Design ____________________________ independent hydrostatic drive of travel variable flow swash plate piston pump and
gear pressure compensation
Pump flow ______________________ max. 125 l/min (33 gpm) Pump flow ________________ max. 112 l/min (30 gpm)
Max. pressure ________________ adjusted to 420 bar (6090 PSI) Pressure limitation ____ max. 160 bar (2300 PSI)
Travel speed ____________________ 0 – 11 km/h (0 to 6.8 mph) infinitely varia- Control valve ____________ 2 spool control block, can be expanded to
ble, forward and reverse 5 circuits
Steering __________________________ hydrostatic Filter system ____________ return filter with magnetic rod in hydraulic
Service brake __________________ hydrostatic tank
Parking/emergency Control ______________________ single servo-assisted joystick lever for blade
brake ______________________________ automatic multi disc brake in final drives hoist and tilt functions, electrically controlled
Cooling system ________________ hydraulic oil cooler with separate cooling blade float and quick drop
circuit with gear pump and front mounted
cooler
Filter system __________________ cartridge fine filters in the cooling circuit
Final drive ______________________ 2-stage planetary reduction gear
Attachments
Front side__________________ straight blade or 6-way-blade
Rear side __________________ ripper, hydraulic winch or swinging drawbar
Drawbar pull kN Pivot points ______________ maintenance-free, with hardened and
200 polished pins and bushings

150
146
Operator's Compartment
Cab __________________________ resiliently mounted, with integrated ROPS
100 (Roll Over Protective Structure, SAE J
1040/ISO 3471) and FOPS (Falling Objects
Protective Structure, SAE J 231/ISO 3449),
can be tilted with handpump to 40h to the
50 rear for accessibility to machine components,
diagonally arranged doors, all around safety
glass
Operator's seat __________ fully adjustable, suspended swing seat,
0
0 1 2 3 4 5 6 7 8 9 10 11 12 adjustable to operator weight
Travel speed km/h Instrument panel ______ comprehensive instrument panel on the right
side of the operator's seat
Ventilation ________________ pressurized filtered air ventilation, 3 stage
blower, 8 air nozzles, sliding windows on
both sides and in the rear
Heater ______________________ hot water heater
Sound level
at operator’s ear ________ 82 dB(A) on job location, conforms to EG
Track Frame standard 86/662/EWG
Design ____________________________ maintenance-free long (L) or low ground
pressure (M) tractor-type track frames
Mount ____________________________ elastic components at a separate pivot
shaft and an oscillating equalizer bar,
oscillation ± 2,5h
Chains ____________________________ sealed or lubricated, track chain tension
Refill Capacities
via grease tensioner and hydraulic cylin- Fuel tank ________________________________________________________________ 310 l (81.8 gal)
ders, single grouser pads Cooling system __________________________________________________________ 52 l (13.7 gal)
Chain links ____________________ 44 Engine oil__________________________________________________________________ 18 l ( 4.8 gal)
Sprockets ________________________ 2 replaceable segments Splitterbox ________________________________________________________________ 2.5 l ( 0.7 gal)
Track rollers __________________ 7 Hydraulic tank ________________________________________________________ 178 l ( 47 gal)
Carrier rollers ________________ 2 Final drive, each ______________________________________________________ 5.5 l ( 1.4 gal)

Technical Description
2
Basic Machine

G
E

D F
C H

PR 712 B-L PR 712 B-M

ft-in/mm ft-in/mm
A Height over cab 10’2”/3100 10’2”/3100
B Height over engine cover 6’11”/2100 6’11”/2100
C Overall length without attachments 12’1”/3675 12’1”/3675
D Distance idler/sprocket center 8’7”/2615 8’7”/2615
E Height of grouser 2”/56 2”/56
F Track gauge 5’9”/1750 6’4”/1930
G Ground clearance 1’3”/370 1’3”/370
H Width over frame mounting trunions 9’0”/2748 10’1”/3078
Overall width with
pad size 18”/457 mm 3,705 sq.in/2.39 m2 –
22”/560 mm 4,542 sq.in/2.93 m2 –
24”/610 mm 4,945 sq.in/3.19 m2 4,945 sq.in/3.19 m2
28”/711 mm 5,766 sq.in/3.72 m2 5,766 sq.in/3.72 m2
30”/762 mm – 6,185 sq.in/3.99 m2
34”/864 mm – 7,006 sq.in/4.52 m2

Dimensions
3
Straight Blade

H
A

T
K
P U
B

PR 712 B-L PR 712 B-M (LGP)

Blade capacity 2.80 cu.yd/2.14 m3 2.81 cu.yd/2.15 m3

Dimensions ft-in/mm ft-in/mm


A Blade height 3’1"/950 2’11"/900
B Blade width 9’10"/3000 11’0"/3350
H Blade lifting height 2’11"/900 3’0"/905
K Blade drop below ground 1’6"/445 1’6"/445
T Max. blade tilt 1’9"/545 1’9"/540
P Max. blade pitch 10h 10h
U Overall length 15’4"/4665 15’3"/4645
N Track pad width 18"/22"/24"/28" 30"/34"
457/560/610/711 762/864

Operating Weights lb/kg lb/kg


Basic machine with blade
and track pad width of 18"/457 mm 26,019/11800 –
22"/560 mm 26,460/12000 –
24"/610 mm 26,681/12100 –
28"/711 mm 27,122/12300 –
30"/762 mm – 27,783/12600
34"/864 mm – 28,224/12800

Ground Pressure PSI/kg/cm2 PSI/kg/cm2


Basic machine with blade
and track pad width of 18"/457 mm 6.97/0.49 –
22"/560 mm 5.83/0.41 –
24"/610 mm 5.40/0.38 –
28"/711 mm 4.69/0.33 –
30"/762 mm – 4.55/0.32
34"/864 mm – 3.98/0.28

Attachments
4
6-Way-Blade With Inside Mounted U-frame

H A

T
K

P U B

B1

N
Y

U1

PR 712 B-L PR 712 B-M

Blade capacity 3.17 cu.yd/2.42 m3 3.18 cu.yd/2.43 m3

Dimensions ft-in/mm ft-in/mm


A Blade height 3'5"/1050 3'3"/1000
B Blade width 9'8"/2950 10'7"/3235
B1 Transport width 9'0"/2750 9'10"/3000
H Blade lifting height 3'7"/1085 3'7"/1085
K Blade drop below ground 1'6"/445 1'6"/445
T Max. blade tilt 1'5"/440 1'7"/485
P Max. blade pitch 5h 5h
Y Blade angle 23h 23h
U Overall length (blade straight) 15'10"/4835 15'10"/4835
U1 Overall length (blade angled) 17'6"/5335 17'7"/5370
N Track pad width 18"/22"/457/560 24"/28"/30"/610/711/762

Operating Weights lb/kg lb/kg


Basic machine with blade
and track pad width of 18"/457 mm 26,129/11850 –
22"/560 mm 26,570/12050 –
24"/610 mm – 27,011/12250
28"/711 mm – 27,232/12350
30"/762 mm – 27,673/12550

Ground Pressures PSI/kg/cm2 PSI/kg/cm2


Basic machine with blade
and track pad width of 18"/457 mm 7.11/0.50 –
22"/560 mm 5.97/0.42 –
24"/610 mm – 5.4/0.38
28"/711 mm – 4.69/0.33
30"/762 mm – 4.41/0.31

5
6-Way-Blade With Outside Mounted C-frame

H A

T
K

P U B

B1 G R

We recommend using the 6-way-


N blade only in conjunction with rear
mounted attachment or counter-
Y weight.

U1

PR 712 B-L

Blade capacity 3.18 cu.yd/2.43 m3

Dimensions ft-in/mm
A Height of blade 3'3"/1000
B Width of blade 10'7"/3235
B1 Transport width 9'10"/3000
H Blade lifting height 3'11"/1200
K Blade drop below ground 1'4"/410
P Max. blade pitch 5h
Y Blade angled 23h
T Max. blade tilt 1'7"/485
G Width over frame mounting trunions 8'7"/2618
R Width over C-frame 8'7"/2620
U Overall length (blade straight) 16'6"/5040
U1 Overall length (blade angled) 18'3"/5575
N Track pad width 18"/22"/457/560

Operating Weights lb/kg


Basic machine with blade,
counterweight and
track pads 18"/457 mm 29,216/13250
22"/560 mm 29,657/13450

Ground Pressures PSI/kg/cm2


Basic machine with blade,
counterweight and
track pads 18"/457 mm 7.82/0.55
22"/560 mm 6.54/0.46

Attachments
6
Ripper Winch

I
A
H
X B C

D A
G
J
C
B
E

F G E

3-shank rigid type Max. line pull: 50,900 lb/227 kN (23,1 t)


Max. line speed: 0 – 105 m/min. (0 – 344 ft/min.)
Cable size: 3/4"/19 mm
Cable length: 230 ft/70 m

Dimensions ft-in/mm Dimensions ft-in/mm


A Ripping depth 1'4"/ 400 A Height, cable exit 3'9"/1135
B Lifting height 1'8"/ 515 B Overall length 2'1"/ 635
C Overall length attachment raised 3'0"/ 925 C Height drawbar 1'9"/ 525
D Ground clearance below toolbar 6"/ 148 D Drum diameter 8"/ 210
E Overall length attachment lowered 3'11"/1185 E Coiling width 9"/ 230
F Ripping width 6'11"/1860 F Flange diameter 1'6"/ 460
G Toolbar width 6'7"/2000 G Distance to center of drum 1'4"/ 405
H Distance between teeth 2'11"/ 900 H Height to drum center 3'4"/1020
X Slope angle 31h I Total height 4'5"/1350
J Hook radius of winch 1'5"/ 440

Weight lb/kg Weight lb/kg


Ripper complete 1,874/850 Winch complete 2,646/1200

7
Basic machine Operator’s cab
Standard Option Standard Option
Cover engine hood Stowing box x
Cover oil cooler Armrest adjustable x
Exhaust catalyst x Ash tray x
Tow switch NEW! x Rear mirror outside left x
Towing hitch rear x Pressurizer with air filter x
Towing lug front x Operator’s seat 6-way adjustable x
Forestry equipment x Operator’s seat air suspended x
Woodchip handling equipment Fire extinguisher x
Coal handling equipment Dome light x
Landfill equipment x Coat hook x
Battery compartment lockable x Air conditioner x
Filling with environmental friendly oil x FM radio x
Filling with oil SAE 10 x Radio installation kit x
Filling with oil SAE 30 x ROPS/FOPS-cab sound supressed x
Tank guard complete x ROPS-canopy x
Tank guard bottom x Rear mirror inside x
Refuelling pump electrical x Windscreen washer x
Belly pans heavy duty x Windscreen wipers front, rear, doors x
Fire supression system engine compartment x Sliding windows x
Connector external electric power x Protective grids for windows x
Cold start device ether Safety glass tinted x
Cold start device glow plug x Sun blinds x
Radiator coarse mesh x Extra cab heater x
Radiator guard 2-piece, hinged x Cabin heater warm water x
Liebherr Diesel engine x
Fan – hydraulically driven NEW! x
Fan guard x
Engine oil cooler x
Engine doors perforated x
Engine doors hinged, lockable x
Lugs for crane lifting x Instruments – Indicators
Platform rear x
Battery charging x
Special paint x
Hour meter x
Settling pund equipment x
Electronic control x
Fuel water separator x
Speed range x
Fuel water separator with electric heater x
Engine oil pressure x
Air filter dry-type, dual step x
Water temperature x
Wear guard for radiator x
Oil pressure cooling circuit x
Precleaner with automatic dust ejector x
Oil level final drives x

LWT/VM 8434215-1.5-01.02 Printed in Germany by Wolf. Illustrations and data may differ from standard equipment. Subject to change without notice.
Preheater for engine electric x
Float position blade x
Tool kit in batteries compartment x
Fuel level x
Contamination hydraulic filter x
Travel drive Contamination air filter x
Parking brake automatic x Cold start Diesel engine x
Function control automatic x
Control – single lever x
Load limit control electronic x
Travel control electronic x
Travel control 2-speed x
Travel control 3-speed NEW! x
Hydrostatic travel drive x Implement hydraulic
Emergency stop x
Hydraulic control 6-way-blade x
Oil cooler x
Hydraulic control ripper x
Final drives planetary gear x
Hydraulic control winch x
Safety lever x
Variable flow pump, load sensing x
Undercarriage Oil filter with strainer in hydraulic tank
Blade quick drop
x
x
Resilient mounting x Blade float position x
Track shoes extreme service (ESS) Control block for 2 circuits x
Track frame closed x Hydraulic tank oil level control x
Sprocket segments bolt-on x Hydraulic servo control x
Master link 2 piece x
Track shoes with relief holes x
Tracks oil lubricated x
Track guide center part x
Track guard
Undercarriage extented x
x Attachments
Undercarriage low ground pressure x Mounting plate rear for external tools x
Undercarriage standard Drawbar rear hinged x
Undercarriage extra wide tracks x Drawbar rear rigid x
Track frames oscillating +/- 3h x Counterweight rear x
Pivot shaft separate x Ripper single shank
Sprocket segments with recesses x Ripper 3 shank x
Ripper 5 shank x
Electrical system Bumper rear
Rake for landclearing
x

Starter motor 5.4 kW x 6-way-blade inside mounted x


Starter motor 6.6 kW 6-way-blade outside mounted x
Starter motor 9 kW 6-way-blade with hinged corners x
Working lights rear 2 units x Blade – straight blade x
Working lights front 2 units x Blade – semi-U-blade
Battery main switch electric x Blade – trimming blade
Batteries, heavy duty cold start x Blade – U-blade
On-board system 24 V x Blade – angle blade x
Alternator 55 A x Blade – woodchip-U-blade
Alternator 80 A x Blade – coal-U-blade
Back-up alarm x Blade – landfill blade x
Beacon x Push plate x
Horn x Winch x
Start lock electronic x Rock guard for semi-U-blade
Lights additional rear 2 units x Spill plate x
Ligths additional on lift cylinders Wear plates for push arms x
Lights additional on engine hood x Wear plates for blades

LIEBHERR-WERK TELFS GMBH, Hans-Liebherr-Straße 35, A-6410 Telfs, ç (0 52 62) 6 00, Fax (0 52 62) 6 00 72
www.liebherr.com, e-Mail: info@lwt.liebherr.com
With compliments:

Das könnte Ihnen auch gefallen