Beruflich Dokumente
Kultur Dokumente
ORDER NO.
RRV2446
VSX-D810S
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Type
MYXJIEW MYXJIGR MVXJI
Model VSX-D810S
AC220-230V AC220-230V AC230V
Power Requirement
Remarks
CONTENTS
1. SAFETY INFORMATION ...................................... 2 2. EXPLODED VIEWS AND PARTS LIST ............... 3 3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ..... 8 4. PCB CONNECTION DIAGRAM ......................... 36 5. PCB PARTS LIST ............................................... 56 6. ADJUSTMENT .................................................... 62 PIONEER CORPORATION 7. GENERAL INFORMATION ................................ 7.1 DISASSEMBLY AND DIAGNOSIS ............... 7.2 PARTS .......................................................... 7.2.1 IC ............................................................ 7.2.2 DISPLAY ................................................. 8. PANEL FACILITIES AND SPECIFICATIONS ....... 63 63 65 65 71 73
4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
VSX-D810S
1. SAFETY INFORMATION
This service manual is intended for qualified service technicians ; it is not meant for the casual do-ityourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician.
WARNING This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to cause cancer, birth defects or other reproductive harm. Health & Safety Code Section 25249.6 Proposition 65
NOTICE (FOR CANADIAN MODEL ONLY) Fuse symbols (fast operating fuse) and/or be of identical designation.
REMARQUE (POUR MODLE CANADIEN SEULEMENT) Les symboles de fusible (fusible de type rapide) et/ou de remplacement doivent avoir la mme dsignation.
1. SAFETY PRECAUTIONS
The following check should be performed for the continued protection of the customer and service technician.
ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER.
Earth ground
AC Leakage Test
VSX-D810S
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. The mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Screws adjacent to mark on the product are used for disassembly.
2.1 PACKING
1 3 2
NSP
Description
FM Wire Antenna Warranty Card AM Loop Antenna Dry Cell Battery (R6P, AA) Operating Instructions (English) Operating Instructions (German) Remote Control Unit Battery Cover Polyethylene Bag (0.03 230 340) Packing Sheet Left Pad R4 Right Pad R4 Packing Case 810/MY Operating Instructions (Dutch/Swedish/Portuguese) Operating Instructions (French/Italian/Spanish)
Part No.
ADH7005 ARY7022 ATB7009 VEM-013 See Contrast table (2) See Contrast table (2) XXD3029 XZA3002 Z21-038 AHG7069 XHA3024 XHA3025 XHD3152 See Contrast table (2) See Contrast table (2)
NSP
11 12 13 14 15
13
VSX-D810S /MYXJIEW
XRB3005 XRC3031 XRC3032 XRC3033
VSX-D810S /MYXJIGR
Not used XRC3031 Not used Not used
VSX-D810S /MVXJI
XRB3005 Not used Not used Not used
Remarks
VSX-D810S
46
44
16
20
I
19 44 44 44 44 44
N
44 41
J
45 50 44 44
C
39 46
I
56 24 Q 41
Q M P P
44 44 44
44 45 G 4
K L O
57 S 7 55 33 9 M 23 R 10 36 35 T
2C 44
8
N E
44 27
F
44
44
D
52 Q6 S 44 R 31 44 21
A
1 A
44 44
J H
13 E
M L K
H 12
34 44
I 14
O
5 D 46 43 44 28 46
D
22
C B 44
26 44 11 U
47 15
3 F 30 44
Accessory of Front Panel
60 53 B
29 44
R
58
44
A B
48
44
25
44
25 62 44 44 59 49 44 54 K 61 44 44
44
29 44 44 44 51
VSX-D810S
Description
D.D UCOM Assy AMP&PRIMARY Assy REGULATOR Assy AMP INPUT Assy TRANS 2 Assy VIDEO&6CH IN Assy 6CH IN Assy S. VIDEO Assy COMPONENT Assy BOARD TO BOARD Assy FM/AM TUNER MODULE TRANS 1 Assy TRANS 3 Assy TRANS 4 Assy Power Transformer (T1) (AC220-230V) Fuse (FU1 : T3.15A) Cord Stopper AC Power Cord FFC (J32 : 13P/30V) (D.D UCOM CN103 FRONT CN401) FFC (J31 : 31P/30V) (D.D UCOM CN102 FRONT CN402) FFC (J38 : 5P/30V)
(BOARD TO BOARD CN392 COMPORNENT CN5501)
Part No.
XWZ3398 XWZ3381 XWZ3386 XWZ3389 XWZ3404 XWZ3335 XWZ3350 XWZ3363 XWZ3366 XWZ3371 AXQ7232 XWZ3390 XWZ3392 XWZ3369 XTS3047 REK1027 CM-22B See Contrast table (2) XDD3062
Mark No.
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 NSP NSP 51 52 53 54 55
Description
PCB Angle Heat Sink Assy 0.440 Heat Sink Angle F Heat Sink Angle R Heat Sink 0.440 Rear Panel 810MY Bonnet Case Screw PCB Mold Screw Screw Screw FFC (J22 : 3P/30V) (TRANS 4 CN891 AMP INPUT CN251) Fan Motor Fan Holder R4 Fuse Card Binder Assy Hold Assy D.D DSP Assy D TO O Assy FFC (J45 : 4P/30V) (AMP INPUT CN603 COMPORNENT CN1576) FFC (J46 : 7P/30V) (AMP INPUT CN604 COMPORNENT CN1575) FFC (J48 : 9P/30V) (VIDEO&6CH IN CN304 6CH IN CN307) FFC Cover R4 SH Support R4 Shield A R4 Shield B R4 Washer
Part No.
ANG7253 XNH3020 ANG7251 ANG7252 XNH3019 XNC3073 XZN3112 ABA7043 AMR2533 BBZ30P080FMC BBZ30P200FMC FBT40P080FZK XDD3061 XXM3002 XNG3040 AAX7493 XWZ3401 XWZ3402 XWZ3395 XWZ3368 XDD3066
NSP
NSP
FFC (J36 : 23P/30V) (REGULATOR CN801 AMP&PRIMARY CN53) FFC (J39, J40 : 20P/30V) (D.D UCOM CN9501 D.D DSP CN9806) (D.D UCOM CN9502 D.D DSP CN9805) FFC (J34 : 13P/30V) (D.D UCOM CN105 FM/AM TUNER UNIT) FFC (J33 : 15P/30V) (D.D UCOM CN104 VIDEO&6CH IN CN303) FFC (J35 : 19P/30V) (D.D UCOM CN106 AMP INPUT CN254) Insulator Under Base 409
56 57 58 59 60
26 27 28 29 30
NSP
VSX-D810S /MYXJIEW
VDG1080
VSX-D810S /MYXJIGR
VDG1080
VSX-D810S /MVXJI
VDG1076
Remarks
VSX-D810S
14
2 P
31
Description
FRONT Assy POWER SW Assy R. ENCODER Assy H.P. Assy MECHA SW Assy FRONT VIDEO Assy 8P Shield Cable Damper Assy Name Plate LED Lens Select Knob R4B Volume Knob R4B Power Button R4B Power Button M Jog Button R4B
Part No.
XWZ3346 XWZ3352 XWZ3354 XWZ3357 XWZ3358 XWZ3359 XDX3012 AXA7052 PAM1776 PNW2019 XAB3008 XAB3011 XAD3062 AAD7442 XAD3065
Mark No.
16 17 18 19 20 21 22 23 24 25 NSP 26 27 28 29 30 31 32
Description
Door Button R4B RDS Button R4B Display Panel W/MY Button Cover R4B2 Cushion R4B Front Panel 810/MY Magnet 35 Holder L R4 Earth Plate A R4 Earth Plate B R4 Door Assy R4B Door R4B Door Cover R4B Screw Screw Screw Cord Clamper
Part No.
XAD3070 XAD3072 XAK3171 XAK3224 XED3001 XMB3037 AMF7007 XMR3016 XNG3044 XNG3045 XXG3068 XAK3173 XAK3175 XBA3001 PPZ30P080FMC BBZ30P080FMC RNH-184
VSX-D810S
VSX-D810S
3 4 IC102 5
1 CN107 11 9 10 9 22 20
CN901
B
D.D DSP ASSY
IC9551
IC9703 6 7
18 17 19
5 IC9103
IC9706 1 18 2
IC9707 2 1
IC303 1
CN307 3
CN104 7 11 12
S
6CH IN ASSY
IC302 7 9 3
10
IC302 1 5 5
6 11
C
3 IC304 1 7 1 9 10
IC111
Q
VIDEO & 6CH IN ASSY
7 5
IC301
S. VIDEO ASSY
IC351, IC352
7 5 9 9 5 6 3
J
D
CN901
CN301
J
FRONT VIDEO ASSY
6 CN901
CN354
11
11 1 1
8
1 2 3 4
VSX-D810S
M
IC103 CN1576 2
LA
CN1551 3
H.P. ASSY
17 CN601 9
IC601 22 15
RY751
CN106
Q603
C
AMP & PRIMARY ASSY
G
Q601 IC106 34 5 7 8 5 24 9
M
RY754 COMPONENT ASSY
IC602 26
RY753
Q653
11 33 IC107 3 1 1
M
COMPONENT ASSY IC601 RY752 26 24
Q651 11
Q632
M
COMPONENT ASSY IC602 RY752 14 18
6 36 12 1 Q631
C
IC106 4 2 5 7 Q682
M
COMPONENT ASSY
VSX-D810S
Q112
Q
+BVH -BVH S591
Q303
C
POWER AMP IC601, IC602
A
Q701 Q702 D702 D701
LB
T51
MECHA SW ASSY
-BVL FL AC
D
AC IN
N
T+12V
CN402
IC805
A A
T1 POWER TRANSFORMER
F
7 8
511
O N
FRONT ASSY (XWZ3346)
J G
B
404
D TO O ASSY (XWZ3368)
A A 1/2, A 2/2
D.D UCOM ASSY (XWZ3398)
T R
U
CN201
Q F
VIDEO& 6CH IN ASSY (XWZ3335) REGULATOR ASSY (XWZ3386) 6CH IN ASSY (XWZ3350)
10
1 2 3 4
CN251
C C 1/2, C 2/2
VSX-D810S
Note : When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST".
501
P LB
471
LA
H.P. ASSY (XWZ3357)
I
TRANS4 ASSY (XWZ3369)
CN891
J6
J7
J8
H
J2 J1
D
851
J5
J4
701
J44
M
COMPONENT ASSY (XWZ3366)
1577
11
5 6 7 8
A 1/2
A
CN901
12
A 1/2
1
F
2
CN802
3 4
VSX-D810S
K
CN1001
Q CN303
: The power supply is shown with the marked box.
A 2/2
N
B
A 2/2
A 2/2
C
A 2/2
E-VR IC
E-VR IC
CN401
13
8
A 2/2
A 2/2
5 6 7
A 1/2
CN402
A 2/2
A 1/2
A 1/2
A 1/2
D
VSX-D810S
14
A 2/2
1
G CN254
4
VSX-D810S
B 1/4 CN9805
A 1/2
B 1/4 CN9806
A 1/2
D
A 2/2
8
15
B 1/4
D.D DSP ASSY (XWZ3395)
B 2/4
A 2/2 CN9501
16
B 1/4
1
VSX-D810S
B 2/4
B 3/4
C
B 4/4
A 2/2 CN9502
B 1/4
8
17
B 2/4
A
B 3/4
CN1002
B 1/4
B
B 1/4 B 3/4
VSX-D810S
18
B 2/4
1
VSX-D810S
B 3/4
CODEC
B 4/4
B 1/4
DAC DIR
F
5
CN804
6 7
B 2/4
8
19
B 3/4
B 1/4 B 2/4
20
B 3/4
1
VSX-D810S
B 2/4
B 1/4
B 3/4
8
21
B 4/4
22
B 4/4
1
VSX-D810S
B 1/4
B 2/4
C
B 1/4
B 4/4
8
23
C 1/2
A
AMP&PRIMARY ASSY
(XWZ3381)
D
MYXJIEW,MYXJIGR,MVXJI MYXJI,MVXJI MYXJI, MVXJI MYXJI, MVXJI MYXJI, MVXJI
G CN253
24
C 1/2
1
VSX-D810S
CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE ONLY WITH SAME TYPE NO. 491.125 FOR IC701 AND IC702 MFD, BY LITTELFUSE INC. CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE ONLY WITH SAME TYPE NO. 491003 FOR IC853 MFD, BY LITTELFUSE INC.
MYXJI, MVXJI
MYXJI,MVXJI
VSXD810S
D
TRANS2 ASSY (XWZ3404)
MYXJI,MVXJI
POWER TRANSFORMER
C 2/2
MYXJI, MVXJI
CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE ONLY WITH SAME TYPE NO. 491004 FOR IC851 AND IC852 MFD, BY LITTELFUSE INC. CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE ONLY WITH SAME TYPE NO. 491001 FOR IC603 MFD, BY LITTELFUSE INC.
C 2/2
C 2/2
M CN1575
M CN1576
NOTE FOR FUSE REPLACEMENT CAUTION - FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE WITH SAME TYPE AND RATINGS ONLY.
5 6 7
CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE ONLY WITH SAME TYPE NO. 491010 FOR IC604, IC605, IC606, AND IC607 MFD, BY LITTELFUSE INC.
C 1/2 D E
8
25
VSX-D810S
3.10 AMP&PRIMARY (2/2), REGULATOR, AMP INPUT, TRANS1 and TRANS4 ASSYS
A 1/2 CN101
B 2/4 CN9802
Q
D
CN302
26
C 2/2 F
1
VSX-D810S
FAN MOTOR
A 2/2 CN106
G (XWZ3389)
C 2/2
AMP&PRIMARY ASSY (XWZ3381)
C 1/2
C 1/2 CN601
I
TRANS4 ASSY (XWZ3369)
LB
CN591
CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE ONLY WITH SAME TYPE NO. 491.630 FOR IC891 AND IC892 MFD, BY LITTELFUSE INC.
POWER TRANSFORMER
ATT7037 CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE ONLY WITH SAME TYPE NO. 491.315 FOR IC52 MFD, BY LITTELFUSE INC.
C 1/2
NOTE FOR FUSE REPLACEMENT CAUTION - FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE WITH SAME TYPE AND RATINGS ONLY.
C 2/2 G H I
8
27
K D TO O ASSY (XWZ3368)
J
A 1/2 CN107
CN354
C 2/2 J44
C
M 1577
LB
MECHA SW ASSY (XWZ3358)
LA
H.P. ASSY (XWZ3357)
28
J K LA LB
1 2
B 2/4 CN9801
A 1/2 CN108
VSX-D810S
VSX-D810S
CN392
C 1/2 CN603
C 1/2 CN604
LA CN1551
M
4
29
N
A
R.ENCODER ASSY S511 : TONE S512 : MULTI JOG DIAL S513 : MASTER VOLUME
A 1/2 CN102
30
A 1/2 CN103
N O
1
VSX-D810S
FL Tube
P
POWER SW ASSY (XWZ3352)
POWER SW ASSY S501 : POWER STANDBY/ON FRONT ASSY S451 : DIRECT S452 : MONITOR S453 : DVD 5.1ch S454 : DSP MODE S455 : SIGNAL SELECT S456 : DD/DTS S457 : MIDNIGHT S458 : SPEAKER S459 : MPX S460 : BAND S461 : MEMORY S462 : CLASS S463 : TUNING (+) S464 : TUNING () S465 : STATION (+) S466 : RF ATT S467 : CHARA SEARCH S468 : EON S476 : STATION ()
RDS Decoder IC
N P
8
31
VSX-D810S 3.13 VIDEO&6CH IN, BOARD TO BOARD, 6CH IN and S. VIDEO ASSYS
Q
A
CN803
R
BOARD TO BOARD ASSY (XWZ3371)
A 1/2
CN104
F
C D
M CN551
S
32
Q R S
1
VSX-D810S
CN901
VSX-D810S
T
8
33
VSX-D810S
B
(FM)
(FM) (FM) (FM)
(FM)
(FM)
(FM)
(FM) (AM) (AM) (AM)
(FM)
(AM)
(FM)
MW RF TUNING BLOCK
(AM)
(AM)
34
U
1
VSX-D810S
(AM)
(AM)
(AM)
(FM)
(TX) (TX)
(AM)
AM/FM IF+MPX IC
(AM)
(TX) (TX)
(FM) (AM)
ATE7003
A 1/2
C D 6 7
PLL IC
(FM) (AM)
U
8
CN105
35
(AM)
(AM)
VSX-D810S
1. Part numbers in PCB diagrams match those in the schematic diagrams. 2. A comparison between the main parts of PCB and schematic diagrams is shown below.
Symbol In PCB Diagrams Symbol In Schematic Diagrams B C E B C E Part Name
3. The parts mounted on this PCB include all necessary parts for several destinations. For further information for respective destinations, be sure to check with the schematic diagram. 4. View point of PCB diagrams.
Connector
Transistor
Capacitor
B C E B B C E D D G S G S D G S C E B C E
SIDE A
Transistor with resistor
P.C.Board
Chip Part
SIDE B
Resistor array
3-terminal regulator
S 6CH IN ASSY
S 6CH IN ASSY
IC305
Q CN304
(XNP3032-B)
(XNP3032-B)
SIDE A
36
SIDE B
2 3 4
S
1
REGULATOR ASSY
A
B
CN9802
Q807 Q805 Q808 Q803 Q806 Q801 IC804 Q804 Q802
(XNP3033-B)
SIDE A A
CN101
IC805
IC803
E TRANS3 ASSY
C J6 J4 J3 J5
IC802
J7
IC801
Q CN302
C CN53 G CN251
POWER TRANSFORMER
TRANS4 ASSY
(XNP3032-B)
C J1 J2
(XNP3032-B)
SIDE B
SIDE A
C 701
37
D E F H I
VSX-D810S
B CN9806
B CN9805 J CN901
CN401
N
CN402
G
CN254
IC5901 IC110
K CN1001
D
38
A
1
VSX-D810S
U CN201 Q CN303
IC107 Q111 Q112 IC105 Q107 Q108 IC106 Q109 IC110 Q110
IC1301 IC104
(XNP3034-B)
Q251 Q252
IC102
SIDE A
F CN802
D
A
8
39
VSX-D810S
IC101
IC112 IC111
40
A
1
VSX-D810S
(XNP3034-B)
SIDE B
A
8
41
VSX-D810S
A CN9501
A CN9502
Q9610 Q9609 Q9608 Q9607 Q9605 Q9606 Q9603 Q9604 Q9601 Q9602
Q9612 Q9611
IC9552 IC9103
A CN108
K D TO O ASSY
(XNP3032-B)
SIDE A
42
B K
1
VSX-D810S
IC9507
IC9508
IC9812 IC9504
(XNP3034-B)
SIDE A F CN804
B
8
43
VSX-D810S
C
IC9152 IC9151 IC9552 IC9502 IC9503 IC92
44
B
1
VSX-D810S
C
IC9202 IC9201 IC9701 IC9702 IC9703 IC9706 IC9704 IC9705 IC9707 IC9604 IC9603 IC9602
(XNP3034-B)
SIDE B
B
8
45
VSX-D810S
FAN MOTOR
SIDE A
LB
MECHA SW ASSY
(XNP3032-B)
I CN891 A CN106
(XNP3033-B)
SIDE B E J3
SIDE A
Q704 Q702 Q703
C AMP&PRIMARY ASSY
E J6
C
Q701
E J7
Q655
Q651 Q653
D
IC602 IC601 IC603
(XNP3033-B)
SIDE A
46
C G LB
1
VSX-D810S H J2 H J1
A
IC52
NEUTRAL LIVE
IC51 Q51
AC IN
D 851
E J5 E J4
M CN1575
M CN1576
F CN801
5 6 7
C
8
47
N FRONT ASSY
P POWER SW ASSY
48
N P
1
VSX-D810S
A
CN103
A
CN102
B
O R.ENCODER ASSY
D
(XNP3032-B)
SIDE A
N O
8
49
VSX-D810S
N FRONT ASSY
Q403
Q402
O R.ENCODER ASSY
D
(XNP3032-B)
SIDE B
50
N O
1
VSX-D810S
Q402
IC401
Q404
Q481
Q482 IC481
Q483
Q471
P POWER SW ASSY
5 6 7
N P
8
51
VSX-D810S
Q VIDEO&6CH IN ASSY
F
CN803
Q302 Q301
R
CN390
(XNP3032-B)
SIDE A A
CN104
S
CN307
Q VIDEO&6CH IN ASSY
C
IC301
Q303
(XNP3032-B)
SIDE B
52
Q
1
VSX-D810S
A
CN107
T S. VIDEO ASSY
IC351 IC352
(XNP3032-B)
SIDE B
SIDE A
1 2 3
J R T
4
53
C CN604
(XNP3032-B)
SIDE A
M COMPONENT ASSY
C
(XNP3032-B)
SIDE B
IC552
IC553
IC551
LA H.P. ASSY
54
LA M
1
SIDE A
A CN105
Q202
(ANP7338-B)
SIDE B
(ANP7338-B)
Q201 IC201 Q203 IC202 Q205 Q204
U
4
55
VSX-D810S
Mark No. Description Part No. Mark No. Description Part No.
The mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. When ordering resistors, first convert resistance values into code form as shown in the following examples.
Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47k ohm (tolerance is shown by J=5%, and K=10%). 561 ........................................................ RD1/4PU 5 6 1 J 560 56 101 473 ........................................................ RD1/4PU 4 7 3 J 47k 47 103 0.5 R50 ..................................................................................... RN2H R 5 0 K 1 1R0 ..................................................................................... RS1P 1 R 0 K Ex.2 When there are 3 effective digits (such as in high precision metal film resistors). 5621 ...................................................... RN1/4PC 5 6 2 1 F 5.62k 562 101 Description Part No.
AXQ7232 XWK3011 XWZ3335 XWZ3346 XWZ3350 XWZ3352 XWZ3354 XWZ3357 XWZ3358 XWZ3359 XWZ3363 XWZ3366 XWZ3368 XWZ3369 XWZ3371 XWK3024 XWZ3381 XWZ3386 XWZ3389 XWZ3404 XWZ3390 XWZ3392 XWK3028 XWZ3395 XWZ3398
Mark No.
Mark No.
Description
Part No.
TC9459F UPC4570G2-TFB 2SC1740S 2SC2412K 2SC3326 1SS355 RB501V-40 UDZS5.1B UDZS6.8B
FM/AM TUNER MODULE NSP COMPLEX ASSY VIDEO&6CH IN ASSY FRONT ASSY 6CH IN ASSY POWER SW ASSY R.ENCODER ASSY H.P. ASSY MECHA SW ASSY FRONT VIDEO ASSY S.VIDEO ASSY COMPONENT ASSY D TO O ASSY TRANS4 ASSY BOARD TO BOARD ASSY AMP&PS ASSY AMP&PRIMARY ASSY REGULATOR ASSY AMP INPUT ASSY TRANS2 ASSY TRANS1 ASSY TRANS3 ASSY D.D & INPUT ASSY D.D DSP ASSY D.D UCOM ASSY
IC112 IC104IC107, IC110 Q101 Q251, Q252 Q107Q112 D103, D105, D106, D254, D255 D201, D202 D104, D256 D101, D102
NSP
CAPACITORS
C101C114, C121C123 C126C128, C152C154 C158C160, C197, C198 C207, C208, C221, C222 C228, C229 C211, C212 C235, C241 C5906 C251, C252, C5902 C130C137, C146C151 C161, C162, C202, C245C247 C261 C5904 C157 C144, C145, C250 C117, C118 C225, C226, C232, C233, C239 C244 C155, C156 C115, C116, C234, C240 CCSRCH101J50 CCSRCH101J50 CCSRCH101J50 CCSRCH101J50 CCSRCH101J50 CCSRCH220J50 CCSRCH221J50 CCSRCH271J50 CCSRCH471J50 CEAT100M50 CEAT100M50 CEAT100M50 CEAT101M10 CEAT101M16 CEAT3R3M50 CEAT470M25 CEAT470M50 CEAT470M50 CEAT471M10 CEAT4R7M50
SEMICONDUCTORS
C173, C174 CKSQYB224K16 C256 CKSQYF105Z16 C271, C5912 CKSRYB102K50 C119, C120, C124, C125 CKSRYB103K50 C171, C172, C179, C180, C183 CKSRYB103K50 C199C201, C203, C204 C223, C224, C230, C231 C237, C238, C242, C243 C248, C249 C140, C143, C253C255, C5907 CKSRYB103K50 CKSRYB103K50 CKSRYB103K50 CKSRYB103K50 CKSRYB104K16
56
VSX-D810S
Mark No. Description Part No.
CKSRYB152K50 CKSRYB153K50 CKSRYB822K50 CKSRYF104Z16 CKSRYF104Z25 CKSRYF473Z50
Mark No.
Description
Part No.
CCSRCH100D50 CCSRCH101J50 CCSRCH101J50 CCSRCH102J50 CCSRCH150J50 CCSRCH180J50 CCSRCH221J50 CCSRCH271J50 CCSRCH470J50 CCSRCH471J50 CCSRCH471J50 CCSRCH471J50 CCSRCH471J50 CCSRCH471J50 CCSRCH471J50 CCSRCH560J50 CCSRCH820J50 CCSRCH821J25 CEAT221M10 CEJQ100M25 CEJQ101M10 CEJQ101M10 CEJQ1R0M50 CEJQ2R2M50 CEJQ330M10 CEJQ330M10 CEJQ470M16 CEJQ470M16 CEJQ470M25 CEJQ4R7M50 CEJQ4R7M50 CEJQ4R7M50 CEJQR47M50 CKSRYB102K50 CKSRYB103K50 CKSRYB103K50 CKSRYB103K50 CKSRYB103K50 CKSRYB103K50 CKSRYB103K50 CKSRYB103K50 CKSRYB104K16 CKSRYB104K16 CKSRYB104K16 CKSRYB122K50 CKSRYB152K50 CKSRYB182K50 CKSRYB222K50 CKSRYB222K50 CKSRYB272K50 CKSRYB333K16 CKSRYB472K50 CKSRYB682K50 CKSRYB821K50 CKSRYF104Z25 CKSRYF104Z25 CKSRYF104Z25 CKSRYF104Z25 CKSRYF104Z25 CKSRYF104Z25 CKSRYF104Z25
C236 C139, C142 C138, C141 C227 C1631, C1632 C184, C185
CAPACITORS
C9510, C9511 C9115, C9135, C9160, C9609, C9610 C9721, C9722, C9735, C9900 C9822 C9107 C9106 C9621, C9622, C9749, C9751, C9809 C9509, C9629 C9159 C9101, C9104, C9112, C9114, C9119 C9122, C9130, C9154, C9156, C9503 C9505, C9507, C9513, C9515, C9518 C9520, C9522, C9525, C9528, C9553 C9555, C9557, C9559, C9561, C9564 C9617, C9618, C9639, C9757 C9201, C9202 C9707, C9708 C9611, C9612, C9736 C9113 C9523, C9526, C9643, C9644, C9770 C9501, C9516, C9551, C9740 C9801, C9802, C9812, C9814 C9123, C9125 C9127, C9529 C9713, C9714, C9727, C9728, C9739 C9753, C9765C9769 C9102, C9108, C9117, C9120 C9151, C9152, C9162, C9562 C9803, C9805 C9203, C9204, C9206, C9207 C9603, C9604, C9615, C9616 C9627, C9628, C9761, C9811,C9813 C9110 C9131, C9745, C9781, C9815 C9103, C9105, C9118, C9121, C9124 C9133, C9134, C9153, C9155 C9157, C9158, C9502, C9504, C9506 C9508, C9512, C9514, C9517, C9519 C9521, C9524, C9527, C9531, C9552 C9554, C9556, C9558, C9560, C9563 C9572, C9636, C9637, C9816 C9109, C9116, C9126, C9626, C9784 C9804, C9806, C9817, C9818, C9831 C9841, C9901, C9904, C9905 C9605, C9606, C9633, C9755 C9211, C9212 C9703, C9704, C9715, C9716, C9729 C9601, C9602, C9613, C9614, C9625 C9763 C9701, C9702 C9732 C9645 C9111 C9717, C9718, C9731 C9163, C9164, C9166, C9205 C9208C9210, C9607, C9608 C9619, C9620, C9631, C9632 C9705, C9706, C9709C9712 C9723C9726, C9730, C9737, C9738 C9759, C9760, C9810, C9819C9821 C9823
RESISTORS
R171R173 R174, R175 Other Resistors RS1/16S102J RS1LMF101J RS1/16S&&&J
OTHERS
CN9501, CN9502 20P CONNECTOR CN9505 10P CONNECTOR CN103, CN105 13P CONNECTOR CN104 15P CONNECTOR CN106 19P CONNECTOR CN102 31P CONNECTOR JA101JA104 PIN JACK (4P) CN107 CONNECTOR POST CN101, CN108 19P SOCKET 101104 PCB BINDER X5901 CERAMIC RESONATOR (15.7MHz) 52044-2045 52045-1045 52045-1345 52045-1545 52045-1945 52045-3145 AKB7048 B3B-PH-K KP200TA20L VEF1040 ASS7032
SEMICONDUCTORS
57
VSX-D810S
Mark No. Description Part No.
RS1/16S&&&J
Mark No.
Description
Part No.
CCCSL101J50 CCCSL6R0D50 CCCSL6R0D50 CEANP2R2M50 CEANP2R2M50 CEAT100M2A CEAT101M10 CEAT101M16 CEAT101M16 CEAT101M35 CEAT102M16 CEAT221M10 CEAT470M25 CEAT4R7M50 CEAT4R7M50 CFTYA224J50 CFTYA224J50 CGCYX103M25 CKCYB102K50 CKCYB331K50 CKCYB331K50 CKPUYB102K50 CQMBA472J50
RESISTORS
All Resistors
OTHERS
CN9805, CN9806 20P CONNECTOR JA9150, JA9152,JA9153 OPTICAL LINK IN JA9155 OPTICAL LINK OUT CN9801 20P SOCKET CN9802 9P SOCKET JA9151 1P PIN JACK X9101 CRYSTAL RESONATOR (24MHz) X9501 CRYSTAL RESONATOR (27.0MHz) 52045-2045 GP1FA551RZ GP1FA551TZ KP200TA20L KP200TA9L VKB1077 ASS7025 VSS1086
C684 C611C614, C636, C637 C661C664, C686, C687 C615, C616, C638, C665, C666 C688 C705, C706 C712 C609, C610, C635, C659, C660 C685 C711 C53 C697 C54 C605, C606, C633, C655, C656 C683 C751C756, C761C764 C771, C772 C55C57 C601, C602, C652, C681, C696 C603, C604, C632, C653, C654
AMP&PRIMARY ASSY
IC52 PROTECTOR (315mA) IC603 PROTECTOR (1A) IC701, IC702 PROTECTOR (125mA) IC604IC607 PROTECTOR (10A) IC51 IC601, IC602 Q703 Q702 Q696, Q697 Q704 Q605, Q606, Q633, Q655, Q656 Q683 Q601Q604, Q631, Q632 Q651Q654, Q681, Q682 Q701 Q51 D56, D57, D601, D603, D606 D608, D631, D632, D651D654 D683, D684, D751D754 D757, D758 D701, D702 D711 D58 D712 D602, D604, D681, D682 D51D55, D721D724 AEK7003 AEK7009 AEK7020 AEK7022 NJM78M56FA PAC011A 2SA1145 2SB1238X 2SC1740S 2SC1845 2SC2240 2SC2240 2SC2878 2SC2878 2SD1859X KRC101M 1SS133 1SS133 1SS133 1SS133 D5SBA20(B) MTZJ22D MTZJ5.1A MTZJ5.1B MTZJ8.2A S5688G
SEMICONDUCTORS
RESISTORS
R52 R615 R751, R752, R755, R761, R762 R772 R753, R754, R756, R763, R764 R771 R711 R617, R622, R639, R667, R668 R691 (0.22/5W) Other Resistors RD1/2PM270J RD1/4PU331J RD1/4PUF101J RD1/4PUF101J RS1LMF4R7J RS1LMF4R7J RS2LMF332J XCN3001 XCN3001 RD1/4PU&&&J
OTHERS
52 3P CABLE HOLDER CN603 4P CONNECTOR CN604 7P CONNECTOR CN53 23P CONNECTOR CN751, CN752 SPEAKER TERMINAL 8-P H 51, H 52 FUSE CLIP T 51 STANDBY TRANSFORMER CN601 18P PLUG CN51 AC CODE SOCKET KN51, KN601EARTH METAL FITTING 701 7P CABLE HOLDER 51048-0300 52045-0445 52045-0745 52045-2345 AKE7059 AKR7001 ATT7037 KM200TA18 RKP1751 VNF1084 XKP3047
D
ACG1005 ACG7020 ACH7135 ACH7137 CCCSL101J50
TRANS2 ASSY
IC853 PROTECTOR (3A) IC851, IC852 PROTECTOR (4A) AEK7015 AEK7018
SEMICONDUCTORS
CAPACITORS
C707, C708 (0.01F/AC250V) C51, C52 (10000pF/AC250V) C703, C704 (3300F/42V) C701, C702 (4700F/71V) C607, C608, C634, C657, C658
OTHERS
851 7P CABLE HOLDER XKP3047
TRANS3 ASSY
58
VSX-D810S
Mark No. Description Part No. Mark No. Description
3P CONNECTOR
Part No.
52045-0345
OTHERS
REGULATOR ASSY
IC803, IC804 IC801, IC805 IC802 Q801, Q803, Q805, Q807 Q802, Q804, Q806, Q808 D809, D810 D801D804 NJM78M05FA NJM78M12FA NJM79M12FA KRA103M KRC101M MTZJ6.2A S5688G
CN891
SEMICONDUCTORS
CAPACITORS
CAPACITORS
C808, C811 C805, C806, C813 C801, C802 C809 C803, C804, C807, C810, C812 CEAT101M10 CEAT101M16 CEAT222M25 CEAT332M16 CGCYX103M25
RESISTORS
All Resistors RS1/16S&&&J
OTHERS
JA902 CN901 PIN JACK (4P) CONNECTOR AKX7014 S8B-PH-K-S
OTHERS
CN801 CN802 CN803 CN804 23P CONNECTOR 20P PLUG 5P PLUG 9P PLUG 52045-2345 KM200TA20 KM200TA5 KM200TA9
K LA
D TO O ASSY
CN1001,CN1002 20P PLUG KM200TA20
OTHERS
H.P. ASSY
C1551, C1552 CKSRYB223K50
SEMICONDUCTORS
CAPACITORS RESISTORS
R1553, R1554 R1551, R1552 RS1LMF471J RS2LMF331J
OTHERS
CN1551 CONNECTOR(3P) JA1551 JACK KN1551 EARTH METAL FITTING KPE3 RKN1002 VNF1084
CAPACITORS
C251 C254 C252, C253 CEANP470M25 CEAT101M25 CKPUYF103Z25
LB
MECHA SW ASSY
S591 ASG7014
RESISTORS
All Resistors RD1/4PU&&&J
OTHERS
CN251 CN254 CN252 CN253
OTHERS
CN591 3PJUMPER CONNECTOR 52151-0310
H I
TRANS1 ASSY
COMPONENT ASSY
IC551 IC552, IC553 D1575,D1576 TC74HC4053AF TK15420M 1SS355
SEMICONDUCTORS
TRANS4 ASSY
SWITCHES AND RELAYS
RY1575 RELAY XSR3002 IC891, IC892 PROTECTOR (630mA) AEK7006 D891 S1WB(A)60SD
SEMICONDUCTORS
CAPACITORS
C551C554, C557, C558 C1581, C555, C556, C559C562 C566, C568 CEAT101M10 CKSRYB103K50 CKSRYB103K50
CAPACITORS
C891, C892 CEAT471M35
59
VSX-D810S
Mark No. Description Part No.
RS1/16S&&&J
Mark No.
X481 X401 401
Description
CERAMIC RESONATOR (4.332MHz) CERAMIC RESONATOR (7.2MHz) REMOTE RECEIVER UNIT
Part No.
ASS7004 ASS7018 GP1U28X
RESISTORS
All Resistors
OTHERS
1577 CN1576 CN551 CN1575 1575 JA553 JA551 CABLE HOLDER(3P) 4P CONNECTOR 5P CONNECTOR 7P CONNECTOR PIN JACK(6P) 3P RCA PINJACK 6P RCA PINJACK 51063-0305 52045-0445 52045-0545 52045-0745 AKB7089 AKB7124 AKB7128
R.ENCODER ASSY
S511 S513 S512 ROTARY ENCODER ROTARY ENCODER ASG1051 XSX3005 XSX3006
FRONT ASSY
IC481 IC401 Q481 Q483 Q401, Q402, Q442, Q471 Q403, Q404, Q441, Q482 D407, D442 D403, D405 D401, D404 BU1923F PDG261A 2SA1037K 2SC3326 DTA124EK DTC143EK 1SS355 DAN217 DAP202K
OTHERS
511 CABLE HOLDER (7P) 51063-0705
SEMICONDUCTORS
POWER SW ASSY
D501 BR3371XJ30A
CAPACITORS
C420 (220F/35V) C404 (0.047F/5.5V) C489, C490 C488 C483 C486 C402 C409, C410, C484 C412 C405 C442 C451C453, C472, C481, C482 C495 C401, C403, C411, C419, C441 C531 C408, C416, C418, C471 C492C494, C496, C497 C485 C406, C407 ACH7101 ACH7132 CCSRCH270J50 CCSRCH561J50 CEAT101M10 CEAT1R0M50 CEAT221M6R3 CEAT2R2M50 CEAT470M50 CEJQ221M6R3 CEJQ470M10 CKSRYB102K50 CKSRYB102K50 CKSRYB103K50 CKSRYB103K50 CKSRYB104K16 CKSRYB104K16 CKSRYB472K50 CKSRYB473K16
VIDEO&6CH IN ASSY
IC301 Q302 Q303 Q301 D301, D302, D305, D306 D303, D304 NJM2296M 2SA1515 2SC3326 2SC3377 1SS355 UDZS6.2B
SEMICONDUCTORS
CAPACITORS
C347 C307C310, C312, C314, C338 C1360, C302 C339, C340 C304C306 C333 C311, C313 CCSRCH470J50 CEAT470M25 CKSRYB103K50 CKSRYB104K25 CKSRYB221K50 CKSRYB331K50 CKSRYB473K25
RESISTORS
R313, R316 Other Resistors RS3LMF390J RS1/16S&&&J
RESISTORS
All Resistors RS1/16S&&&J
OTHERS
CN304 CN303 CN305 CN301 CN302 9P CONNECTOR 15P CONNECTOR 6P PIN JACK 13P SOCKET 5P SOCKET 52044-0945 52044-1545 AKB7123 KP200TA13L KP200TA5L
OTHERS
471 404 CN401 CN402 V401 CABLE HOLDER (4P) CABLE HOLDER (7P) 13P CONNECTOR 31P CONNECTOR FL TUBE 51063-0405 51063-0705 52044-1345 52044-3145 XAV3010
60
VSX-D810S
Mark No. Description Part No. Mark No. Description Part No.
LC72131MD-TFB 2SC2412K DTA124ES DTC124EK 1SS133 HVU187 MTZJ5.1C UDZS6.8B
OTHERS
IC202 Q201, Q204, Q205, Q601 Q202 Q203, Q602 D201 D601 D202 D101
6CH IN ASSY
IC302IC305 NJM4558MD
SEMICONDUCTORS CAPACITORS
C1354, C1359, C319, C320 C327, C328, C342C345 C348, C349 C1362 C1361 C1357 C1358, C321, C324, C331, C332 C1352, C1353, C1355,C1356,C316 C322, C323, C329, C330 C1350, C1351, C317, C318 C325, C326 CCSRCH101J50 CCSRCH101J50 CCSRCH101J50 CCSRCH121J50 CCSRCH680J50 CEAT220M25 CEAT4R7M50 CKSRYB103K50 CKSRYB103K50 CKSRYB221K50 CKSRYB221K50
CAPACITORS
C605 C212, C213, C226, C233C235 C240, C614 C206 C231, C232 C223 C229 C224 C227 C241 C243 C228 C237 C211 C210 C103, C104, C204, C238, C609 C102, C208, C216, C217, C220 C239, C242, C604, C610, C615 C225 C607, C608 C201, C205, C214, C230, C236 C244, C611 C221 C603 C215 C202, C222 C606 CCSQCH680J50 CCSRCH101J50 CCSRCH101J50 CCSRCH120J50 CCSRCH150J50 CEAT100M50 CEAT101M10 CEAT1R0M50 CEAT220M25 CEAT2R2M50 CEAT330M16 CEAT3R3M50 CEAT470M10 CEJQ1R0M50 CEJQ470M16 CKSRYB102K50 CKSRYB103K50 CKSRYB103K50 CKSRYB153K50 CKSRYB182K50 CKSRYB223K50 CKSRYB223K50 CKSRYB224K10 CKSRYB392K50 CKSRYB471K50 CKSRYB473K16 CKSRYB561K50
RESISTORS
All Resistors RS1/16S&&&J
OTHERS
CN307 308 9P CONNECTOR PIN JACK(6P) 52044-0945 AKB7089
S. VIDEO ASSY
IC351, IC352 D351D354 NJM2296M 1SS355
SEMICONDUCTORS
CAPACITORS
C375, C376 C352, C355, C358, C361C363 C366 C372, C373, C377, C378 C351, C353, C354, C356, C357 C359, C367 C364, C365, C368C371 CCSRCH470J50 CEAT470M25 CEAT470M25 CKSRYB103K50 CKSRYB104K25 CKSRYB104K25 CKSRYB221K50
RESISTORS
R211 R221 R233 R103, R104 Other Resistors RD1/4PU221J RD1/4PU222J RD1/4PU391J RS1/10S221J RS1/16S&&&J
RESISTORS
All Resistors RS1/16S&&&J
OTHERS
CN354 CN351 JA351 CN353 CN352 CONNECTOR POST 11P SOCKET JACK 2-4P MINI DIN SOCKET 3-4P MINI DIN SOCKET B5B-PH-K KP200TA11L RKN1004 XKP3044 XKP3045
OTHERS
CN201 BN201 X201 13P CONNECTOR 2P TERMINAL WITH PAL SHIELD CASE T SHIELD CASE B CRYSTAL RESONATOR (7.2MHz) FM FRONT END AM RF TUNING BLOCK 52044-1345 AKA7002 ANK7072 ANK7073 ASS1093 AXF7005 AXX7072
SEMICONDUCTORS
61
VSX-D810S
6. ADJUSTMENT
6.1 TUNER SECTION
AM Tuner Section
There is no adjustment in the AM tuner.
FM Tuner Section
Set the mode selector to FM BAND. Connect the wiring as shown in Fig. 1. Step No.
1
Adjustment Title
T-METER Adjustment
ANT. Input level and signal condition Input Level Frequency Modulation (dBV) (MHz)
98 OFF 80
Contents
Adjust L201 so that the DC voltage between Pin 21 and Pin 23 of IC201 (Test point Vtm) gets within 0 50mV.
MPX SG
PRODUCT
DC Voltmeter
L201
1 24
IC201
pin 21 pin 23
SIDE B
Fig.2 Adjustment Point
62
VSX-D810S
7. GENERAL INFORMATION
7.1 DISASSEMBLY AND DIAGNOSIS
Diagnosis 1
Remove the Bonnet (seven screws). Note : This photograph shows other models. However, the work method is the same.
2 2
3
Rear Panel
6 3 3
Pull up
7
REGULATOR Assy
Diagnosis
AMP&PRIMARY Assy
Heat Sink
Note : The product does not operate when the screws of Speaker Terminal are taken off from Rear Panel. When FM/AM TUNER MODULE was removed, the product operates except FM/AM TUNER function.
63
VSX-D810S
PCB Location
R. ENCODER Assy FRONT VIDEO Assy AMP INPUT Assy D.D UCOM Assy D.D DSP Assy S.VIDEO Assy VIDEO&6CH IN Assy REGULATOR Assy 6CH IN Assy
O J G A B T Q F S
N L
P POWER SW Assy E TRANS 3 Assy I TRANS 4 Assy H TRANS 1 Assy D TRANS 2 Assy C AMP&PRIMARY Assy M COMPONENT Assy
SIDE A
SIDE A
64
G4/A4 98 G5/A5 97
G6/A6 96 G7/A7 95
G8/A8 94 G9/A9 93
G10/A10 92 G11/A11 91
G12/A12 90 VDD 89
G13/A13 88 G14/A14 87
G15/A15 86 A16 85
A17 84 A18 83
G2 G1 NC ACIN RDS_DT RDS_CK Not used RMC VER_2 PLL_CE Not used Not used DSPM_RDY DSPM_CS2 STEREO TUNED VENC_A VENC_B A.MUTE DSPM_RDY DSPM_CS DSPM_CK DSPM_SI DSPM_SO MVOL_ATT ST_EVR PLL_DO KEYIN1 KEYIN2
1 2 3 4 5 6 7 8 9
A19 82 A20 81
A21 80 A22 79 A23 78 PH7/A24 77 PH6/A25 76 PH5/A26 75 PH4/A27 74 PH3/A28 73 PH2/A29 72 PH1/A30 71 PH0/A31 70 PG7/A32 69 PG6/A33 68 PG5/A34 67 PG4/A35 66 PG3/A36 65 PG2/A37 64 PG1/A38 63 PG0/A39 62 PF7/A40 61 PF6/A41 60 PF5/A42 59 PF4/A43 58 PF3/A44 57 PF2/A45 56 PF1/A46 55 PF0/A47 54 PD7/A48 53 PD6/A49 52 PD5/A50 51
S11 S12 S13 S14 S15 S16 S17 S18 S19 S20 S21 S22 4053INH 4053A RY_B RY_C/R RY_A RY_AC GAIN_SEL NECK_SEL DSPM_RST 9164_CS T_MUTE T_POWON RY_HP FM+(RDS) 9459_ST Not used 9273_CS Not used
10 PE6/PWM 11 PE7/TO/ADJ 12 PC0/KR0 13 PC1/KR1 14 PC2/KR2 15 PC3/KR3 16 PC4/KR4 17 PC5/KR5 18 PC6/KR6 19 PC7/KR7 20 PB0/CINT 21 PB1/CS0 22 PB2/SCK0 23 PB3/SI0 24 PB4/SO0 25 PB5/SCK1 26 PB6/SI1 27 PB7/SO1 28 AVREF 29 PA1/AN0
31 PA2/AN2 32 PA3/AN3 33 PA4/AN4 34 PA5/AN5 35 PA6/AN6 36 PA7/AN7
30 PA1/AN1
46 PD0/A55
47 PD1/A54
48 PD2/A53 VIDEO3
49 PD3/A52 SYS_CK
AMP_DC
AMP_OL
VIDEO1
VIDEO2
FENC_A
FENC_B
SYS_DT
KEYIN3
VER_1
50 PD4/A51
39 EXTAL
37 AVSS
40 XTAL
45 VFIP
44 VDD
41 VSS
38 RST
43 TEX
42 TX
65
VSX-D810S
Pin Function
No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
Pin Name
G2 G1 NC ACIN RDS_DT RDS_CK Not used RMC VER_2 PLL_CE Not used Not used DSPM_RDY DSPM_CS2 STEREO TUNED ENC_A ENC_B AMUTE DSPM_RDY DSPM_CS1 DSPM_CK DSPM_SI DSPM_SO MVRATT ST_EVR PLL_DO AVref KEYIN1 KEYIN2 KEYIN3 VER_1 FENC_A FENC_B AMP_DC AMP_OL AVSS RST EXTAL XTAL VSS TX TEX VDD VFDP VIDEO1 VIDEO2 VIDEO3 SYS_DT SYS_CK
I/O
O O I I I I I I O O O I I I I I I O O O O I O O O I I I I I I I I I O O O DSP Micro Computer READY input CS input for DSP Micro Computer Stereo/Monoral signal judgment signal TUNED information EVOL Rotary encoder signal input A EVOL Rotary encoder signal input B Audio mute Grid output 2 Grid output 1 Connect to VDD AC pulse input
Pin Function
Active
H H
Serial control DATA signal of RDS communication Serial control CLOCK signal of RDS communication Connect to GND Remote control signal input (no-carrier signal) Destination switch 2 Chip select signal for communication with LC72131 (tuner) H
L L H H H H
RADY of DSP Micro Computer communication Chip select output for control of DSP Micro Computer Clock signal for communication with DSP Micro Computer DATA input signal for communication with DSP Micro Computer DATA output signal for communication with DSP Micro Computer ATT control of master volume (L : Less than -15dB) Strobe signal for communication with electric volume IC Data input signal for communication with LC72131 (tuner) Connect to VDD Key input A/D conversion port 1 Key input A/D conversion port 2 Key input A/D conversion port 3 Destination switch (A/D input) FUNC Rotary encoder signal input A FUNC Rotary encoder signal input B DC abnormality detection of protection circuit (L : Abnormality detection) *1 Over-load detection of protection circuit (L : Abnormality detection) *2 Connect to VSS Reset Connect to the oscillator (7.2MHz) Connect to VSS Open Connect to VSS +5V -30V NJM2296D control Data signal for communication with M62446, TC9163, TC9164 and PLL Clock signal for communication with M62446, TC9163, TC9164 and PLL H H H L L
*1 : When DC voltage was output from amplifier, "POWER OFF" is displayed at FL display. *2 : When the output of amplifier became overload state, "OVER LOAD" is displayed at FL display. 66
VSX-D810S
No.
51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
Pin Name
Not used 9273_CS Not used 9459_ST FM+(RDS) RY_HP T_POWON T_MUTE 9164 CS DSP_RST NECK_SEL GAIN_SEL RY_AC RY_A RY_C/R RY_B 4053A 4053INH S22 S21 S20 S19 S18 S17 S16 S15 S14 S13 S12 S11 S10 S9 S8 S7 S6 S5 S4 S3 VDD S2 S1 Not used G10 G9 G8 G7 G6 G5 G4 G3
I/O
O O O O O O O O O O O O O O O O TC9273 Chip select
Pin Function
Active
H H H H H H
Electronic volume TC5496 Strobe for SB Tr switch ON/OFF for power supply of RDS decoder (L : AM, power OFF , H : Other) HP relay ON/OFF Tuner module ON/OFF (North America model only) Tuner mute TC9163, TC9164 Chip select DSP Micro Computer reset 5.1ch, surround mode and A+B Stereo : H / Stereo : L Gain select (5.1ch and Stereo of analog input : H ) AC relay ON/OFF Speaker A relay ON/OFF Rear/Center Speaker relay ON/OFF Speaker B relay ON/OFF Component terminal control Component terminal control Segment output 22 Segment output 21 Segment output 20 Segment output 19 Segment output 18 Segment output 17 Segment output 16 Segment output 15 Segment output 14 Segment output 13
H H H H H H H
Segment output 12 Segment output 11 Segment output 10 Segment output 9 Segment output 8 Segment output 7 Segment output 6 Segment output 5 Segment output 4 Segment output 3
O O
5V Segment output 2 Segment output 1 Not used (Fixed Vfdp) Grid output 10 Grid output 9 Grid output 8 H Grid output 7 Grid output 6 Grid output 5 Grid output 4 Grid output 3 H
67
VSX-D810S
2CHSW1
2CHSW2
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
P100 97 AVSS 96
P101 95 P102 94
P103 93 P104 92
P105 91 P106 90
P107 89 P00 88
P01 87 P02 86
P03 85 P04 84
P05 83 P06 82
ASO ACK AREQ Not used M_DO M_DI M_CK GND GND M_CS2 M_REDAY RESET GND 5V Not used M_CS1 Not used Not used Not used Not used Not used Not used Not used Not used Not used Not used Not used Not used
1 2 3 4 5 6 7 8 9
P07 81
Not used
ANOVL
ADRY
ARDY
ADRT
AIRT
GND
ASI
5V
5V
P10 80 P11 79 P12 78 P13 77 P14 76 P15 75 P16 74 P17 73 P20 72 P21 71 P22 70 P23 69 P24 68 P25 67 P26 66 P27 65 VSS 64 P30 63 VCC 62 P31 61 P32 60 P33 59 P34 58 P35 57 P36 56 P37 55 P40 54 P41 53 P42 52 P43 51
31 P67 32 P66 33 P65 34 P64 35 P63 36 P62 37 P61 38 P60 39 P57 40 P56 41 P55 42 P64 43 P53 44 P52 45 P51 46 P50 47 P47 48 P46 49 P45 50 P44
Not used Not used CDC_CK CDC_DT CDC_CS ERR Not used Not used Not used Not used FS96 CODEC PD DIR SDTO DIR PD Not used Not used GND Not used 5V ATT Not used Not used Not used Not used SELC SELB SELA Not used ST CK
10 P87 11 P86 12 RESET 13 XOUT 14 VSS 15 XIN 16 VCC 17 P85 18 P84 19 P83 20 P82 21 P81 22 P80 23 P77 24 P76 25 P75 26 P74 27 P73 28 P72 29 P71 30 P70
Not used
T_LXD
T_RXD
T_SCLK
CSDO
CREQ
T_BUSY
MUTE
CDT
CRST
ABOT
GND
ADMD
CA17
CA16
CA15
CCK
CCS
68
DT
5V
VSX-D810S
Pin Function
No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
Pin Name
ASO ACK AREQ Not used M_DO M_DI M_CK BYTE T_PGM/OE M_CS2 M_READY RESET XOUT VSS XIN VCC MN1 M_CS1 Not used Not used Not used Not used Not used Not used Not used Not used Not used Not used Not used Not used TXD RXD T-SCLK T-BUSY CSDO CDT CCK CRST CREQ ABOT VSS CCS CA17 CA16 CA15 T-Vdd Not used MUTE ADMD DT
I/O
O O O O O I I I I O O I I O O O O O O O O O O O O O I I O O I O I O O O O O I O O O O For E-SW (TC9164) For E-SW (TC9164) For E-SW (TC9164) CS for Crystal DSP For Crystal DSP For Crystal DSP For Crystal DSP 5V For FLASH rewriting For FLASH rewriting For FLASH rewriting For FLASH rewriting DATA OUT for Crystal DSP DATA IN for Crystal DSP CLK for Crystal DSP RESET for Crystal DSP REQ for Crystal DSP ABOOT for Crystal DSP DATA OUT to Main microcomputer DATA IN from Main microcomputer AK7706 DATA output AK7706 CLOCK output AK7706 REQ
Pin Function
Active
CLOCK IN for Main microcomputer communication GND Pull down to CNVss, GND (For FLASH rewriting) CS output for Main microcomputer communication READY output for Main microcomputer communication Reset (from Main microcomputer) Oscillator GND Oscillator 5V 5V CS input for Main microcomputer communication
69
VSX-D810S
No.
51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
Pin Name
CK ST Not used SELA SELB SELC Not used Not used Not used Not used ATT VCC Not used VSS Not used Not used DIR PD DIR SDTO CDC_PD FS96 Not used Not used Not used Not used ERR CDC_CS CDC_DT CDC_CK Not used Not used Not used Not used Not used Not used 2CHSW2 2CHSW1 Not used Not used ANOV Not used Not used Not used AIRT ARDY ADRY AVSS ADRT VREF AVCC ASI
I/O
O O O O O O O O O O O O O O O I O I O O O O I O O O O O O O O O O O O O I O O O O I I O I Analog input overload detection (A/D) DIR CS for CODEC communication DATA OUT for CODEC communication Clock for CODEC communication Power down for DIR DIR DATA IN Power down for CODEC 96K GND ATT output 5V For LOGIC IC, TC74ACT151F For LOGIC IC, TC74ACT151F For LOGIC IC, TC74ACT151F For E-SW (TC9164) For E-SW (TC9164)
Pin Function
Active
For TC9215 control (SW H : PASSIV, L : POWERED) For TC9215 control (SB H : DSP, L : 6CH)
AK7706DSP INIT reset (control it only in a power start) AK7706 writing READY input AK7706 output data READY input GND AK7706 DSP reset 5V 5V
70
VSX-D810S
SIGNAL SELECT
DIGITAL DTS
ANALOG DIGITAL
ATT
MONITOR RF ATT
EON
dB
Grid Assignment
10G
SIGNAL SELECT SB DIGITAL PRO LOGIC DSP DNR ATT DIRECT MIDNIGHT LOUDNESS
1G
MONITOR RF ATT EON
DIGITAL DTS
ANALOG DIGITAL
dB
9G
8G
7G
6G
5G
4G
3G
2G
Segment Designation
S2 S4 S3 S1 a1 j f h k m n p d d1 d2 Dp1 Dp2 c e c b f g g e r a2 a b
(9G to 2G)
(1G)
71
VSX-D810S
Pin Connection
Pin No. 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 Connection F2 F2 NP NP P22 P21 P20 P19 P18 P17 P16 P15 P14 P13 P12 P11 P10 P9 P8 P7 P6 P5 P4 P3 P2 Pin No. 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
Connection P1 NX NX NX NX NX NX NX NX NX 10G 9G 8G 7G 6G 5G 4G 3G 2G 1G NP NP F1 F1 NOTE 1) F1, F2.......... Filament 2) NP................ No pin 3) NX................ No extend pin 4) DL................. Datum Line 5) 1G to 10G..... Grid 6) Field of vision is a minimum of 29 from the lower side.
Anode Connection 10G MONO P1 B P2 A P3 SP P4 MONITOR P5 LOUDNESS P6 MIDNIGHT P7 DIRECT P8 DNR P9 ATT P10 P11 DSP P12 SB P13 PRO LOGIC P14 DIGITAL P15 P16 ANALOG P17 DIGITAL P18 P19 P20 DTS DIGITAL P21 P22 SIGNAL SELECT
9G
a1 a2 h j k b f m g c e r p n d1 d2 Dp2 Dp1 S1 S4 S2 S3
8G
a1 a2 h j k b f m g c e r p n d1 d2 Dp2 Dp1 S1 S4 S2 S3
7G
a1 a2 h j k b f m g c e r p n d1 d2 Dp2 Dp1 S1 S4 S2 S3
6G
a1 a2 h j k b f m g c e r p n d1 d2 Dp2 Dp1 S1 S4 S2 S3
5G
a1 a2 h j k b f m g c e r p n d1 d2 Dp2 Dp1 S1 S4 S2 S3
4G
a1 a2 h j k b f m g c e r p n d1 d2 Dp2 Dp1 S1 S4 S2 S3
3G
a1 a2 h j k b f m g c e r p n d1 d2 Dp2 Dp1 S1 S4 S2 S3
2G
a1 a2 h j k b f m g c e r p n d1 d2 Dp2 Dp1 S1 S4 S2 S3
1G
dB
2a 2b 2f 2g 2c 2e 2d 1a 1b 1f 1g 1c 1e 1d
RDS RF ATT EON
TUNED STEREO
72
VSX-D810S
7 4 5 6 89 0 = ~
1
) ( * & ^ % $ #
1 STANDBY indicator Lights when the receiver is in standby mode (note that the receiver consumes a small amount of power (1W) in standby mode). 2 OFF/ _ ON (Main power) button If the button is OFF (), the power of the receiver is shut off and the STANDBY/ON button on the receiver or the RECEIVER button on the remote control do not function. Pressing the button again will turn the receiver ON (_) and the receiver enters the standby mode. In the standby mode, you can turn on the receiver using STANDBY/ON button on the receiver or the RECEIVER button on the remote control. STANDBY/ON button Switches the receiver between on and standby (note that the receiver consumes a small amount of power (1W) in standby mode). 3 STATION (+/) buttons Selects station memories when using the tuner. 4 TUNING (+/) buttons Selects the frequency when using the tuner. 5 DIRECT button Use to switch DIRECT playback on or off. This mode bypasses the tone controls, channel levels, 2/DTS and DSP modes for the most accurate reproduction of a program source. 6 MONITOR button Press to switch tape monitoring on/off. 7 DIGITAL NR button Switches the DIGITAL NR on or off. To reduce extraneous noise switch on DIGITAL NR.
8 DSP MODE button Use to switch between the various DSP modes available (HALL1, HALL 2, JAZZ, DANCE, THEATER1, THEATER 2, 5/ 6CH STEREO) and DSP off. Use this button to create different surround sound effects from any stereo source. 9 Remote sensor Receives the signals from the remote control. 0 SIGNAL SELECT button Use to select an analog or digital or AUTO signal. - 2/DTS button Use to switch between the various 2/DTS surround modes. = TONE button This button allows you to activate the BASS & TREBLE controls. To adjust the BASS and/or TREBLE use the MULTI JOG dial. Tone can only be used in 2 channel stereo sound mode. The tone controls have no effect on the B speaker system. ~ MULTI JOG dial You can use this dial for two purposes. Firstly, in normal mode turn it to select a source component. Secondly, use it to adjust the BASS and/or TREBLE levels when the TONE button has been activated (as explained above). ! MASTER VOLUME Use to set the overall listening volume. @ VIDEO INPUT jacks Connect a video camera, video game system, etc. to the VIDEO INPUT jacks. # MIDNIGHT button Use when listening to movie soundtracks at low volume. This feature will enable you to hear quiet sounds and not get jolted by loud or sudden sound effects.
73
VSX-D810S
$ SPEAKERS button Use to switch the speaker system A = B = A+B = off. In B and A+B speaker modes you hear only 2 channel stereo
sound.
% MPX button If there is interference or noise during a FM radio broadcast, or the radio reception is weak, press the MPX button to switch the receiver into mono reception mode. This should improve the sound quality and allow you to enjoy the broadcast. ^ BAND button Press to select the AM or FM band. & MEMORY button Press to memorize a station for recall using the STATION (+/) buttons. * CLASS button Switches between the three banks (classes) of station memories.
( RF ATT button Use to lower the input level of a radio signal that is too powerful or contains interference thus causing the receiver to distort CHARACTER/SEARCH button Use to search for different program types in RDS mode. It is also used to input station names. EON MODE button Use to search for different programs that are transmitting traffic or news information (this search method is called EON). ) PHONES jack Use to connect headphones but this does not switch the speakers off.
Rear Panel
PCM/2 /DTS IN
AUX CD
AM LOOP
FM UNBAL 75
ANTENNA
CENTER
COAX
(DVD) IN (CD) O U T
SURROUND BACK
R R
L L
SURROUND BACK Y
TO MONITOR TV OUT
OPT
S S
(CD-R) OPT
OUT
PB
PR
PB (TV/SAT) IN 2
PR
R
FRONT
R
SURROUND
CENTER
IN
IN IN
IN R E C P L A Y
FRONT
IN
S TV / SAT S
OUT CD - R / TAPE / MD IN
IN
S P E A K A E R S
FRONT
CENTER
BACK
SURROUND
FRONT
74
VSX-D810S
Display
1
SIGNAL SELECT
5 6
ATT
- =
EON
DIGITAL DTS
ANALOG DIGITAL
MONITOR RF ATT
SP A MONO
dB
#$
&
1 SIGNAL SELECT indicators Light to indicate the type of input signal assigned for the current component (see Front Panel, 0 SIGNAL SELECT). When the AUTO setting is being used on the VSX-D810S receiver a set of brackets will appear around the SIGNAL SELECT indicators. 2DIGITAL : Lights when a Dolby Digital signal is played. DTS: Lights when a source with DTS audio signals is played. ANALOG : Lights when an analog signal is selected. DIGITAL : Lights when a digital audio signal is selected. [ ]: Lights when the AUTO setting is selected. 2 DTS indicator Lights when DTS mode is being used. 3 2 DIGITAL indicator When the 2 (DOLBY)/DTS mode of the receiver is on, this lights to indicate playback of a Dolby Digital signal. However, 2 PRO LOGIC lights during two channel playback of Dolby Digital. 4 Surround Back indicator Lights when most Surround Back channel flag encoded (6.1channel) software is playing. (With some Surround Back channel software the surround back indicator wont light because there is no flag encoded in the software.) If you play DTS 5.1/6.1 channel software surround sound will be heard whether it is encoded with a surround back channel flag or not. 5 OVERLOAD indicator This lights when an analog signal is too high (the SIGNAL SELECT would have to be on ANALOG). It indicates the sound is distorting and the input signal should be reduced. 6 ATT indicator Lights when ATT is used to attenuate (reduce) the level of the input signal (can only be used in ANALOG mode). 7 DIRECT indicator Lights when source DIRECT is in use. This function bypasses all tone, balance, DSP and Dolby Surround effects. 8 SPEAKER indicator Shows if the speaker system is on or not. SP 3A means that speakers are switched on. SP 3 means that speakers are switched off. 9 MONITOR indicator Lights when MONITOR is selected. Used to hear a recording as it's being made.
0 RF ATT indicator Lights when the RF ATT is on. - EON indicator The box around EON indicator lights to inform you that the currently tuned station carries the EON data service. When the EON mode is set, the EON indicator lights, but during actual reception of an EON broadcast the EON indicator will flash. An empty box in the EON indicator spot means it is possible to pick up an EON broadcast but the receiver has not been set to do so (this will only appear when RDS is switched on). = RDS indicator Lights when an RDS broadcast is received. ~ CHARACTER display Shows the radio frequency or function (DVD/LD, CD, etc.) receiver is using . ! 2 PRO LOGIC indicator When the 2/DTS mode of the receiver is on, this lights to indicate playback of a two channel source. @ DNR indicator Lights when the digital noise reduction is on. Use to reduce extraneous noise. It can be used with any sound mode. # DSP indicator Lights when any Advanced Theater or DSP mode is selected. $ MIDNIGHT indicator Lights when MIDNIGHT listening mode is in use. % LOUDNESS indicator Lights when the LOUDNESS is on. Use to boost the bass and treble at low volume. ^ TUNER indicators MONO: Lights when the mono mode is set using the MPX button. TUNED: Lights when a broadcast is being received. STEREO: Lights when a stereo FM broadcast is being received in auto stereo mode. & MASTER VOLUME LEVEL Shows the overall volume level. Volume level is maintained even when the power is off. --- dB indicates the minimum level, and 0dB indicates the maximum level.
75
VSX-D810S
Remote Control
3 RCV button Use this button when setting up the surround sound for the receiver. Also press it if you want to use special features attached to some of the number buttons, for example MIDNIGHT, 5.1/7.1, EFFECT +/ or ATT. 4 NUMBER/MODE buttons Use the number buttons to select the radio frequency in tuner DIRECT ACCESS mode or the tracks in CD, DVD mode etc. Also, buttons marked with the following names have special functions. If you try to use one of these functions but the display flashes it means that function cannot be used in the current mode (for example DSP modes cannot be used when 5.1 Ch (VSX-D710S)/ 7.1 Ch (VSXD810S) setting is on). MIDNIGHT button Use to put receiver in MIDNIGHT mode. To use first press the RCV button then operate this button. 5.1/7.1 button (VSX-D810S is 7.1 Ch) When the DVD/LD or DVD 5.1/7.1 Ch function is selected each press switches the DVD/LD input between DVD/LD and DVD 5.1/7.1 Ch. To use first press the RCV button then operate this button. ATT button When the overload indicator lights use this button to attenuate (lower) the level of an analog input signal and prevent distortion. To use first press the RCV button then operate this button. EFFECT +/ buttons Use to add or subtract the amount of effect in different DSP sound modes (except 6 Ch Stereo) or advanced listening modes. To use first press the RCV button then operate these buttons. 5 THE FOLLOWING BUTTONS ARE BOTH CONTROLS FOR OTHER COMPONENTS (LIKE A DVD PLAYER) AND DEDICATED TUNER CONTROLS. THE TUNER CONTROLS ARE EXPLAINED HERE. YOU CAN USE THEM AFTER YOU HAVE PUSHED THE TUNER MULTI CONTROL BUTTON. BAND button Use to switch between the AM and FM band when in TUNER mode. CLASS button Use to switch between the three banks (classes) of station memories. MPX button Use to switch between auto stereo and mono reception of FM broadcasts. If the signal is weak then switching to MONO will improve the sound quality. D. ACCESS button Use to directly access a radio station by pressing the number of the station you want. DISPLAY button Use to display the RDS information. RF ATT button Use to lower the input level of a radio signal that is too powerful or contain interference thus causing the receiver to distort.
1 2 3 4
SOURCE
RECEIVER
# @
DVD
TV
VCR
CD-R
1
MIDNIGHT
2
5.1 / 7.1
3
ATT
4 7 10
MPX
5
EFFECT
6 9
DISC
D.ACCESS
8 0
7
CLASS
!
8
5 6 7 8
3
DISPLAY
BAND
RF ATT
1
2 /DTS
DSP
CH SELECT
CH LEVEL
FUNCTION
LOUDNESS
FL DIMMER
SETUP
MUTING
TUNE ST
ENTER
ST
~ =
TUNE
TVFUNC
TV
TV CONTROL
1 SOURCE button Use to turn on/off other components connected to the receiver. 2 MULTI CONTROL buttons Use to put the receiver/remote control in the stated mode. For other equipment controls, see Controlling the Rest of Your System.
76
VSX-D810S
6 2 /DTS button Use to put the receiver in DOLBY DIGITAL, DOLBY SURROUND and DTS modes. To use first press the RCV button then operate this button. DSP button Use to put receiver in one of the DSP modes. To use first press the RCV button then operate this button. TEST TONE button Use to sound the TEST TONE when setting up the surround sound of the receiver (the 2 /DTS mode must be on). To use first press the RCV button then operate this button. SIGNAL SELECT Use to select the proper signal (analog, digital) for the source your are inputting. On the VSX-D810S receivers there is an AUTO setting. In this setting the receiver will automatically switch between the analog and digital signals according to what is being input. If both signals are input the AUTO setting will choose the digital one. This setting is convenient as the receiver will always choose the best or appropriate signal. To use first press the RCV button then operate this button. 7 CH SELECT button Use to select a speaker when setting up the surround sound of the receiver. CH LEVEL +/ Use to set up the levels of the surround sound of the receiver. FUNCTION button Use to select the playback or recording source. This button lets you cycle through the different functions of the receiver in the following order: CD, TUNER, AUX, CDR/ TAPE, VCR/DVR, DVD/LD, DVD 7.1 ch, VIDEO, and TV/ SAT. 8 LOUDNESS button Use to switch on the loudness. This feature is useful for getting good bass and treble sounds listening at low volumes. FL DIMMER button Use this button to make the fluorescent display (FL) dimmer or brighter. There are three brightness settings as well as an off setting. SETUP button Use this button when setting up the remote control to control other components. MUTING button Use to mute the sound or restore the sound if it has been muted. 9 THE FOLLOWING BUTTONS ARE DEDICATED TV CONTROL BUTTONS. THEY ARE ONLY USED FOR CONTROLLING YOUR TV. TV FUNC button Use to select the TV function. TV button Use to turn on/off the power of the TV. TV VOLUME +/ buttons Use to adjust the volume on your TV. 0 MENU button Use to access different menus associated with your DVD player. To use first press the DVD button then operate this button.
- MASTER VOLUME +/ buttons Use to set the overall listening volume. = CHANNEL +/ buttons Use to skip tracks backward or forward on CDs, DVDs, etc and change channels on the VCR, DVR, etc. ~ @ # % ( TUNE/ST +/) & ENTER buttons Use these arrow buttons when setting up your surround sound system. These buttons are also used to control DVD menus/options and for deck 1 of a double cassette deck player. The TUNE/ST +/ buttons can be used to find radio frequencies and preset stations, respectively . ! DISC button Use to select a disc and a multi-CD player. To use first press the CD button then operate this button. @ RECEIVER (POWER) button This switches between STANDBY mode and power ON for this receiver. # LED DISPLAY This display flashes when a command is sent from the remote control to the receiver. It also flashes at other times, for example when teaching the receiver preset codes, with specific meanings.
77
VSX-D810S
8.2 SPECIFICATIONS
Amplifier Section
Continuous Power Output (STEREO MODE) FRONT .............. 100 W + 100 W (DIN 1 kHz, THD 1 %, 8 ) Continuous Power Output (SURROUND MODE) FRONT ............................. 100 W/ch (1 kHz, THD 1 %, 8 ) CENTER ............................... 100 W (1 kHz, THD 1 %, 8 ) SURROUND .................... 100 W/ch (1 kHz, THD 1 %, 8 ) SURROUND BACK .......... 100 W/ch (1 kHz, THD 1 %, 8 ) Above specifications are applicable when the power supply is 230V. Input (Sensitivity/Impedance) CD, AUX, VCR/DVR, CD-R/TAPE/MD, DVD/LD, TV/SAT, VIDEO .......................................... 200 mV/47 k Frequency Response CD, AUX, VCR/DVR, CD-R/TAPE/MD, DVD/LD, TV/SAT, VIDEO .......................... 5 Hz to 100,000 Hz +0 dB 3 Output (Level/Impedance) VCR/DVR OUT, CD-R/TAPE/MD REC ..... 200 mV/2.2 k Tone Control BASS ....................................................... 6 dB (100 Hz) TREBLE ................................................... 6 dB (10 kHz) LOUDNESS ................................ +9 dB (100 Hz/10 kHz) Signal-to-Noise Ratio [DIN (Continuous rated power output/50 mW)] CD, AUX, VCR/DVR, CD-R/TAPE/MD, DVD/LD, TV/SAT, VIDEO .............................................. 88 dB/64 dB
FM Tuner Section
Frequency Range ............................... 87.5 MHz to 108 MHz Usable Sensitivity ........... Mono:13.2 dBf, IHF (1.3 V/ 75 ) 50 dB Quieting Sensitivity ............................. Mono: 20.2 dB Stereo: 38.6 dBf Signal-to-Noise Ratio ..................... Mono: 73 dB (at 85 dBf) Stereo: 70 dB (at 85 dBf) Signal-to-Noise Ratio (DIN) .............................. Mono: 62 dB Stereo: 58 dB Distortion ............................................ Stereo: 0.5 % (1 kHz) Alternate Channel Selectivity ..................... 60 dB (400 kHz) Stereo Separation .......................................... 40 dB (1 kHz) Frequency Response ...................... 30 Hz to 15 kHz (1dB) Antenna Input (DIN) .................................. 75 unbalanced
AM Tuner Section
Frequency Range ............................... 531 kHz to 1,602 kHz Sensitivity (IHF, Loop antenna) ............................. 350 V/m Selectivity .................................................................... 30 dB Signal-to-Noise Ratio .................................................. 50 dB Antenna .......................................................... Loop antenna
Miscellaneous
Power Requirements UK model .............................................. AC 230 V, 50/60 Hz European model .......................... AC 220 230 V, 50/60 Hz Power Consumption VSX-D810S ............................................................ 280 W In Standby ...................................................................... 1 W Dimensions ....................... 420 (W) x 158 (H) x 401 (D) mm Weight (without package) VSX-D810S ........................................................... 10.5 kg
VIDEO Section
Input (Sensitivity/Impedance) VCR/DVR, DVD/LD, TV/SAT .......................... 1 Vp-p/75 Output (Level/Impedance) VCR/DVR, TO MONITOR TV OUT ................ 1 Vp-p/75 Frequency Response VCR/DVR, DVD/LD, TV/SAT MONITOR 3 .......................................................... 5 Hz to 7 MHz +0 dB Signal-to-Noise Ratio ............................................... 55 dB
Furnished Parts
AM loop antenna ................................................................ FM wire antenna ................................................................ Dry cell batteries (AA size IEC R6P) .................................. Remote control ................................................................... Operating instructions ........................................................ NOTE: Specifications and the design are subject to possible modifications without notice, due to improvements. 1 1 2 1 1
"DTS" ,"ES" and "DTS Digital Surround" are trademarks of Digital Theater Systems, Inc. Manufactured under license from Digital Theater Systems, Inc.
Accessories
78