Beruflich Dokumente
Kultur Dokumente
Author/ Email: Eray Uyank/eray.uyanik@huawei.com Version: V1.0(20120723) CO., LTD. HUAWEI TECHNOLOGIES
Contents
1. Purposes and Applicable Scenarios of IPRehoming
2. Design and Implementation methods of IPRehoming 3. Hardware and Data Planning of IPRehoming 4. Data Configuration, Commissioning, and Verification of IPRehoming (Key Point)
Purposes
configured for the BTS locally in the static IP networking mode while
the new functions support remote static IP configuration.
Enhanced functions: For the earlier BTS version, in the static IP networking mode, operators can modify locally the configured
Enabling low cost services: The IPRehoming enables remote static IP configuration. In this case, operators do not need to go to the BTS, which contributes to higher efficiency.
Page3
Applicable Scenarios
Page4
IP networking (IPoFE/IPoE1)
Software Requirements
BSC6900: BSC6900V900R011C00SPC720 or later versions BTS: BTS3000V200R013C00SPC003 or later versions BTS3900B: BTS3000V600R013 or later versions.
Page5
to activate the newly configured data. The BTS writes the data
into the Flash and backs up the original data to another Flash. The newly configured data can take effect only after users reset the BTS. Then, the BTS attempts to create links with the BSC using the new data. If the attempt fails, the backup data will be used for another try, that is to say, the BTS attempts to connect to the BSC using data in the two flashes. We have to configure both side, BSC and BTS.
Page6
Data Planning
Data for the BTS: Configure the BTS based on the data planning, including configuration of BTS IP, routers, BSC IP and VLAN, and ppp/mp links.
Page7
IMP BTSDEVIP command: (IMPORT commands are used to write new configuration to BTS flash, but only takes effect after ACT BTSIMPDATA. )
1. After this command is executed successfully, do not run the ACT BTSIMPDATA command to activate the BTS data until the BTS data are imported successfully by running other IMP commands. Then, reset the BTS to modify the BTS static IP addresses that is configured locally. 2. In this command, Port No. specifies the port number of the BTS, Port Cabinet No. specifies the No. of the cabinet where the FE/GE port is located, Subrack No. specifies the No. of the subrack that holds the GTMU board (IP interface board for non-BTS3900E base stations), and Slot No. specifies the No. of the slot that holds the GTMU board (IP interface board for non-BTS3900E base stations). BTS Name must be defined uniquely in the source BSC and target BSC in the case of BTS reparent between BSCs. 3. The values of all the preceding configuration parameters are the ones after the BTS data are changed.
%%IMP BTSDEVIP: IDTYPE=BYID, BTSID=3, CFGSW=ENABLE, PN=0, CN=0, SRN=0, SN=3, IP="10.100.100.3", MASK="255.255.255.0";%% RETCODE = 0 Execution succeeded.
2. The values of all the preceding configuration parameters are the ones after the BTS data are changed.
CFGSW=ENABLE, IPPHYTRANSTYPE=IP_OVER_FE/GE,
BTSCOMTYPE=PORTIP, BTSIP="10.100.100.3", BSCIP="100.100.100.34";%%
the BTS to modify the BTS static IP addresses that is configured locally.
2. The values of all the preceding configuration parameters are the ones after the BTS data are changed.
%%IMP BTSIPRT: IDTYPE=BYID, BTSID=3, CFGSW=ENABLE, DSTIP="100.100.100.32", DSTMASK="255.255.255.252", RTTYPE=NEXTHOP, NEXTHOP="10.100.100.1";%% RETCODE = 0 Execution succeeded.
EXP BTSDEVIP:
Use this command to export the Ethernet port IP address configured by using the IMP BTSDEVIP command.
EXP BTSIPPARA:
Use this command to export the Ethernet port IP address configured by using the IMP BTSIPPARA command.
EXP BTSIPRT:
Use this command to export the BTS routes configured by using the IMP BTSIPRT command.
BSC side configuration: As you can see below, BSC paramaters have not changed yet,
BSC side configuration: ADD IPPATHs as same as previous configuration ACT BTS:
After site is up, you can query the configuration on BTS by running EXPORT commands.
DATA Configuration:
Thank you
www.huawei.com
Copyright2011 Huawei Technologies Co., Ltd. All Rights Reserved. The information in this document may contain predictive statements including, without limitation, statements regarding the future financial and operating results, future product portfolio, new technology, etc. There are a number of factors that could cause actual results and developments to differ materially from those expressed or implied in the predictive statements. Therefore, such information is provided for reference purpose only and constitutes neither an offer nor an acceptance. Huawei may change the information at any time without notice.