Beruflich Dokumente
Kultur Dokumente
Overview
Hidden trouble of Air-Condition Maintenance Process Question & Reply
HUAWEI Confidential
www.huawei.com 2
HUAWEI Confidential
www.huawei.com 3
3 4
Granma Holguin
1 3
Santiago de Cuba
HUAWEI Confidential
www.huawei.com 4
HUAWEI Confidential
www.huawei.com 5
Overview
Hidden trouble of Air-Condition Maintenance Process Question & Reply
HUAWEI Confidential
www.huawei.com 6
Improve Step
HUAWEI Confidential
www.huawei.com 7
HUAWEI Confidential
www.huawei.com 8
Improve Step
HUAWEI Confidential
www.huawei.com 9
Improve Step
HUAWEI Confidential
www.huawei.com 10
Improve Step
HUAWEI Confidential
www.huawei.com 11
Overview
Hidden trouble of Air-Condition Maintenance Process Question & Reply
HUAWEI Confidential
www.huawei.com 12
appearance of the cabinet, note anything abnormal found in the site form, take photo
for them if possible; 2Record the ambient temperature and check if the Air-Condition is working or not, measure and record the AC input voltage and frequency; 3Write down the model and serial number of the cabinet and Air-Condition, check the transformer and the 2 T-Start setting; BTS Name AC/input Voltage Cabinet model Air-Condition model Remark Ambient temperature AC input frequency Serial number Serial number 1Information of the cabinet, installation and appearance of the cabinet; 2Air-Condition is working or not; 3The transformer and the 2 T-Start setting is correct or not;
HUAWEI Confidential
www.huawei.com 13
5Move to the enclosure side and remove the access panel, keep the 4 screws for
later using; 6Install the Hard Start Kit (HSK) 1) Install HSK using M5 nut;
2) Remove Rubber Boot on Capacitor and place one wire on each terminal;
3) Replace Rubber Boot. 4) Route wires so they do not touch metal, use wires ties if needed 7Replace Blower capacitor from 4uF to 7uF
HUAWEI Confidential
www.huawei.com 14
1) Find the Cooling T-stat(On the left of the bracket) and check if it is a 3C T-stat
or 10C T-stat, replace 3C T-Stat with a new 10C T-stat as following steps; 2) Disconnect the wires on the 3C T-stat and then loosen the 3 screwskeep for later using) which fix the T-stat on the bracket, take out the T-stat by move it downwards;
3) Install the 10C T-stat on the bracket in reverse order, and re-connect the 2
wires. Check the part number of the T-stat should be 10-1061-13, wire tie she sensing line, Then replace the label with new 10C T-stat label.. 4) Fully turn the T-stat clockwise then paint the end which point to 27C on the label, and set the T-Stat on 35C(proper setting).
HUAWEI Confidential
www.huawei.com 15
HUAWEI Confidential
www.huawei.com 16
1) Inspect the wire routing of the ambient side, if The wires touch the copper
without sheathing, cover it by sheathing; 2) Check the TXV if there was a wire tie to fix the capillary on the copper tube, If not fix it; 3) Check the cable of external fan, keep wires are tied so they do not rub against
HUAWEI Confidential
www.huawei.com 17
else in advance;
12Switch on (plug in the power cable of) the Air-Condition and do common inspection to it and the cabinet, confirm Air-Condition work; 13Close the front door and telephone to BSC confirm the BTS no alarm and work perfectly, then go to next site;
14In one month after maintenance, often go to the BSC to confirm all the BTS work
perfectly;
HUAWEI Confidential
www.huawei.com 18
Overview
Hidden trouble of Air-Condition Maintenance Process Question & Reply
HUAWEI Confidential
www.huawei.com 19
HUAWEI Confidential
www.huawei.com 20
The End
HUAWEI Confidential
www.huawei.com 21