Beruflich Dokumente
Kultur Dokumente
ZTE University
CDMA-BSS Course Team
Main Content
Carrier Parameters
Channel Parameters
BSS Parameter
Reverse Power Control Parameters BSS Neighbor Cell BSC Handoff Parameters Gain Parameters RLP Parameters PTT SCH Parameters Pay Phone Parameters Special Number Parameters Switch Parameters
BSS Parameters
BSS Parameters
MSC ID
Description :Switch ID. Service provider specifies this parameter. The first 16 digits represent Market
background.
(IMSI).
China = 460, USA = 310, Canada =302a, Singapore = 525.
BSS Parameters
MS IMSI_11_12
Value Range: 00~99 Default: 03 Description: the eleventh and twelfth digits of the IIMSI, when IMSI is 15 digitals
IMSI Structure
An IMSI that is 15 digits in length is called a class0 IMSI (the NMSI is 12 digits in length); an IMSI that is less than 15 digits in length is called a class 1 IMSI (the NMSI is less than 12 digits in length).
BSS Parameters
BSS Parameters
supported.
service zone, the base station shall set this field to its non-zero packet data services zone identifier. If the base station does not support a packet data service zone, the base station shall set this field to 0.
BSS Parameters
CE resource is wasted, and forward capacity is reduced. If soft leg supported number is too low, useful pilots cannot be added into active set. Service quality declines. Reverse interference increases. But CE resource and forward capacity is saved.
BSS Parameter
BSS Parameters Forward Power Control Parameters 1X Forward Power Control Parameters Reverse Power Control Parameters BSS Neighbor Cell
BSS Parameter
BSS Parameters Forward Power Control Parameters 1X Forward Power Control Parameters
Default: MS Power control step size 1:0 MS Power control step size 2:1 MS Power control step size 3:2
or more legs). In terms of power control bits in power control subchannel, MS adjusts transmission power according to this step length.
BSS Parameter
BSS Parameters Forward Power Control Parameters 1X Forward Power Control Parameters
This is for reverse closed Power control setpoint For example: 13000: 21-13=8 dB
BSS Parameter
BSS Parameters Forward Power Control Parameters 1X Forward Power Control Parameters Reverse Power Control Parameters BSS Neighbor Cell
Value Range: 0~1023 Default: Description: Global neighbor cell Id is generated by background automatically. It is unchangeable.
Default: 2
Description: Not Protocol Filed.
SwitchNumber
Value Range: 0~255 Default: Description: used to uniquely identify a special
switching center in a group of switching centers under the same Market ID. when CI_Discriminator equals to 7, SwitchNumber is valid and used to construct MSCID.
BSS Parameter
BSS Parameters
Forward Power Control Parameters 1X Forward Power Control Parameters Reverse Power Control Parameters BSS Neighbor Cell BSC Handoff Parameters Gain Parameters
RLP Parameters
PTT SCH Parameters Pay Phone Parameters Special Number Parameters Switch Parameters
supported. If not support, the MS of RC3 or above are treated as IS-95 MS. This parameter is used in hard handoff with disconnected BSC.
search window and etc. in default. This parameter is used in hard handoff with disconnected BSC.
indication. This parameter is used in the hard handoff with disconnected BSC.
BSS Parameter
BSS Parameters
Forward Power Control Parameters 1X Forward Power Control Parameters Reverse Power Control Parameters BSS Neighbor Cell BSC Handoff Parameters Gain Parameters
RLP Parameters
PTT SCH Parameters Pay Phone Parameters Special Number Parameters Switch Parameters
BSS Parameter
Gain Parameters RLP Parameters PTT SCH Parameters Pay Phone Parameters Special Number Parameters Switch Parameters
In the most of the conditions, the default value is used in these parameter tables.
Main Content
Carrier Parameters
Channel Parameters
BTS Parameters
BTS Parameters
Forward power uprise step size(1 leg) = 4 Forward power uprise step size(2 leg) = 2 Forward power uprise step size(3 leg) = 1
control step length is set too high, the forward quick power control response time is short, but the stable state power deviation is high. If the power control step length is set too low, the stable state power
deviation is low, but the forward quick power control response time is
long.
Forward power down step size(1 leg) = 4 Forward power down step size(2 leg) = 2 Forward power down step size(3 leg) = 1
power control step length is set too high, the forward quick power control response time is short, but the stable state power deviation is high. If the power control step length is set too low, the stable state power deviation is low, but the forward quick power control response time is long.
BTS Parameters
The power assigned by BTS to a subscriber.
Maximum Initial
Power
Minimum
These two parameters decide Maximum threshold and Minimum threshold
179
the initial transmitting power is set too high, F-FCH initial transmitting power is high, and the MS is easier to receive information correctly (Frame Error Rate is low), but the forward capacity is lowered when the channel is established. If the initial transmitting power is set too
low, F-FCH initial transmitting power is low, and the MS may receive
wrong information (Frame Error Rate is high), but the forward power resource is saved.
Nominal transmit power for voice (1 leg) = 169 Nominal transmit power for voice (2 leg) = 175 Nominal transmit power for voice (3 leg) = 171
Power region for voice (1 leg) = 80 Power region for voice (2 leg) = 40 Power region for voice (3 leg) = 32
Main Content
Carrier Parameters
Channel Parameters
Cell Parameter
Cell Parameter
Cell Parameter
Cell Parameter
a cellular system.
Cell Parameter
Cell Identity : CI
Value Range: 0~15 Unit: 64PN chip Default: 4 Description: Protocol Field.
Cell Parameter
Search window size for the Active Set and Candidate Set: SRCH_WIN_A
Value Range: 0~15 Default:6
Search window size for the Remaining Set: SRCH_WIN_R Searcher Window Sizes Value Range: 0 ~15
Default: 0
Cell Parameter
Cell Parameter System Parameter Power Control Reporting Parameter Handoff Parameter Reverse Link Overload Parameter SCH Rate Parameter Redirect Message Parameters Link Cell Neighbor Frequency ECAM Information Repeat Parameters
System Parameter
System Parameter
Value Range: 0~4095 Default:0 Description: Register zone refers to the base station group within a specified system/network. The zone for a BS is specified in the REG_ZONE field. One MS can be registered in more than one zone. The unique SID and NID for the zone can be added through a REG_ZONE. In consideration of paging by LAC, the REG_ZONE should correspond to LAC .
storable zones in the zone table) field in the system parameter message, a BTS can control the maximum number of registered zones of the registered zone table.
Cell Parameter
Cell Parameter
System Parameter Power Control Reporting Parameter
Handoff Parameter
Reverse Link Overload Parameter SCH Rate Parameter
Cell Parameter
Neighbor Frequency
ECAM Information Repeat Parameters
Handoff Parameter
Handoff Parameters
Handoff Parameters
Default: 3
Description: If the pilot signal is in the candidate pilot signal set and also if
the time when its strength is less than T_DROP continuously exceeds T_TDROP, the pilot signal will be transferred to the neighbor pilot signal set.
19
15
319
Unit: -
Intercept in the inequality criterion for adding a pilot to Active Set: ADD_INTERCEPT
Value range: 0 ~ 63 Default: 26 Unit: -0.5dB Description: Add soft handoff intercept.
Intercept in the inequality criterion for dropping a pilot from the Active Set: DROP_INTERCEPT
Value range: 0 ~ 63 Default: 30 Unit: -0.5dB Description: Drop soft handoff intercept .
Dynamic Add Threshold: [(SOFT_SLOPE/8) 10 log10(PS1) + ADD_INTERCEPT/2] Dynamic Drop Threshold : [(SOFT_SLOPE/8) 10 log10(PS2) + DROP_INTERCEPT/2]
Cell Parameter
Cell Parameter System Parameter Power Control Reporting Parameter Handoff Parameter Reverse Link Overload Parameter SCH Rate Parameter Redirect Message Parameters Link Cell Neighbor Frequency ECAM Information Repeat Parameters
Default: 3
reverse load via converting all reverse service channels into 8 K voice R-FCH under RC1. This set of parameters will convert R-FCH of RC1, RC3 and RC4, different target FERs and coding mode (volume or TURBO) R-SCH into the correction factor for 8 K voice R-FCH under RC1.
Cell Parameter
Cell Parameter
System Parameter Power Control Reporting Parameter
Handoff Parameter
Reverse Link Overload Parameter SCH rate Parameter
Cell Parameter
Cell Parameter System Parameter Power Control Reporting Parameter Handoff Parameter Reverse Link Overload Parameter SCH Rate Parameter Redirect Message Parameters Link Cell Neighbor Frequency ECAM Information Repeat Parameters
Cell Parameter
Cell Parameter
System Parameter Power Control Reporting Parameter
Handoff Parameter
Reverse Link Overload Parameter SCH Rate Parameter
Link Cell
Cell Parameter
Cell Parameter System Parameter Power Control Reporting Parameter Handoff Parameter Reverse Link Overload Parameter RSCH Rate Parameter Redirect Message Parameters Link Cell Neighbor frequency ECAM Information Repeat Parameters
Neighbor frequency
Cell Parameter
Cell Parameter
System Parameter Power Control Reporting Parameter Handoff Parameter Reverse Link Overload Parameter RSCH Rate Parameter Redirect Message Parameters Link Cell Neighbor frequency ECAM Information Repeat Parameters
Main Content
Carrier Parameters
Channel Parameters
Carrier Parameter
Traffic Parameter
Carrier Parameter
Carrier Parameter
We can use these two parameters to balance traffic for multiple carrier.
Carrier Parameter
system compared with the IS95 system, which can only work above RC3.
respectively Default: 0 Description: Nominal transmit power offset, expressed in binary supplemental code. This parameter and the parameter Extended nominal transmit power are used in the open loop power control of reverse links.
Carrier Parameter
Carrier Parameter
Carrier Parameter Global Redirect Message Parameters PTT SCH Power Control Parameters
Carrier Parameter
Just default!
Carrier Parameter
Traffic Parameter
Attention the relationship with The cell neighbor list! Carrier neighbor<Cell neighbor
Carrier Parameter
Carrier Parameter Global Redirect Message Parameters PTT SCH Power Control Parameters Neighbor Cell List Access Parameter Power Control Message Parameter Forward Power Overload Parameter Periodic Pilot Measurement Request Order Traffic Parameter
Access Parameter
Access Parameter
Access Probing
Access Channel Request Attempt
Sequence MAX_RSP_SEQ Access Probe Sequence 1 Sequence 2 Sequence 3
(15max)
System Time
PD
PD =0 for Response Message
RS
PD
RS
PD
Request Message ready for transmission Access Probe 1+NUM_STEP (16 max)
PI
Access Probe Access Probe 1 2
Access Probe 3
PI
IP
System Time
TA
RT
TA
RT
TA
Access Parameter
NUM_STEP, PWR_STEP and INIT_PWR function simultaneously in the access attempt sequence of an MS.
Default: 3
Default: 6
Access Parameter
MAX_CAP_SZ
Unit: Frame Value range: 0 ~ 7 Default: 3 Description: Maximum Access Channel message capsule size. 3 less than
the maximum number of Access Channel frames in an Access Channel message capsule.
PAM_SZ
Unit: Frame Value range: 0 ~ 15 Default: 3 Description:Access Channel preamble length. 1 less than the number of
Access Channel frames that mobile stations are to transmit in each Access Channel preamble.
Access Parameter
PROBE_BKOFF
Value Range: 0~15
Default:0
BKOFF
Value Range: 0~15 Default:0 Description: For every access probe sequence, a backoff delay, RS,
Access Parameter
as much as this time before transmitting next access probe TA = (2 + ACC_TMO) * 80ms
PROBE_PN_RAN:
Value Range: 0~9 Default:0 Description: Time randomization for access channel probes.To avoid
collision among the MS to try call access at the same time: PN randomization delay = (PN chip)
0 ~ 2PROBE_PN_RAN-1
Carrier Parameter
Traffic Parameter
Carrier Parameter
Carrier Parameter Global Redirect Message Parameters PTT SCH Power Control Parameters Neighbor Cell List Access Parameter Power Control Message Parameter Forward Power Overload Parameter Periodic Pilot Measurement Request Order Traffic Parameter
Value: 0~30000
Description: Designed power of the cell.
Carrier Parameter
Carrier Parameter Global Redirect Message Parameters PTT SCH Power Control Parameters Neighbor Cell List Access Parameter Power Control Message Parameter Forward Power Overload Parameter Periodic Pilot Measurement Request Order Traffic Parameter
Carrier Parameter
Carrier Parameter Global Redirect Message Parameters PTT SCH Power Control Parameters Neighbor Cell List Access Parameter Power Control Message Parameter Forward Power Overload Parameter Periodic Pilot Measurement Request Order Traffic Parameter
Traffic Parameter
CE search window
Main Content
Carrier Parameters
Channel Parameters
Channel Parameters
ModuleId
Value range:
Default: 1 Description: Module where the Pliot channel is located,The
ElementId
Value range: 0 ~ 35
Default: 0
Description: Element where the pilot channel is located. The
Unit: (X-255)/4
Value range: 0 ~ 255 Default: 225 Description : Provided by network planning, generally
according to the default value. Suppose the configuration value is X, the corresponding dB value is (x-255)/4. For example, if Pilot_gain is set to 225, the corresponding dB value is (225-255)/4 = -7.5dB.
The Synchronous Channel, Paging Channel and Access Channel are similar to this.