Beruflich Dokumente
Kultur Dokumente
Group Members
7-MAE-1:
7-MAE-2:
Neeraj Kalra
A2305410099
Thereby: Increasing the efficiency of the engine. Reducing the fuel consumption of the engine Reducing the unburned hydrocarbons emissions.
Description of Project:
The two stroke engines which was majorly used for single cylinder two wheelers are now expired from the market due its poor fuel efficiency and pollution. Besides these drawbacks the two stroke engines have many advantages over fourstroke engines like mechanical effeciency of the two stroke engine is 1.3 times the four stroke engines since there is no valves, It is simple in construction and weight of the engine is comparabley less, manufacturing and maintanance cost is less, the parts to be lubricated is less. Hence by elemenating the disdvantages specified above the two stroke engines could be brought back to the use and employed in the two wheelrs. This research work deals with the solution to those problems in two stroke engine. By this low cost efficient two wheelers could be manufactured to adhering to the latest pollution norms. The fuel efficiency and low emission of the four stroke engine is due to fuel injection system. If this system is suitably employed in the two stroke engines these benefits could be achieved in low cost compared to the four stroke engines. Implementation of this system will increase the fuel efficiency and reduce the emission.
INTRODUCTION
Two-stroke engine is an internal combustion engine that
completes the process cycle in one revolution of the crank shaft (an up stroke and a down stroke of the piston, compared to twice that number for a four-stroke engine). This is accomplished by using the beginning of the compression stroke and the end of the combustion stroke to perform simultaneously the intake and exhaust (or scavenging) functions. In this way two-stroke engines often provide strikingly high specific power, at least in a narrow range of rotations speeds. The functions of some or all of the valves required by a four-stroke engine are usually served in a two-stroke engine by ports that are opened and closed by the motion of the pistons, greatly reducing the number of moving parts
3 phase stator
Proposed Design
Hardware Required
Fuel Injector Injection Pump High Pressure Pump Low Pressure Pump Sensors Battery Fuel Tank Fuel Filter Engine (60cc) Servo motors Connecting cables Micro-controller Miscellaneous Total
Cost in Rs
2500 5000
Status
3500 5000 2000 500 1000 5000 1000 1000 3000 2000 31,500
To be Programmed
Fabrication Methodology
First, location of fuel injector is to be at 45 degrees. We have already purchased a piston with extended skirt to
close the ports. We are then attaching the crank angle sensor externally. Temperature and pressure sensor are to be placed on the exhaust manifold. Then the sensors will be connected to a micro controller, which will control the fuel injector.
OPERATION
PISTON FROM TDC TO BDC
The inlet port is closed and the air is subjected to crankcase
compression. The piston opens the exhaust port the exhaust gasses in the previous cycle combustion will leave the cylinder. Then the transfer port is opened and the scavenging is done by the incoming air by this the remaining exhaust gas is forced out by the incoming air.
The piston close transfer port. The piston closes the exhaust. Now the compression of
the charge starts The fuel is injected inside combustion chamber immediately after the exhaust port is closed
Continued
The injection pressure is around 8O bars.
The piston uncover the inlet port and the air enter
inside the crankcase Ignition takes place just before the piston reaches TDC and the fuel is burnt.
ADVANTAGES:
mixture through the exhaust port is prevented. Fuel is injected in high pressure so atomisation of the fuel is good and complete combustion will takes place.(injection pressure is around 80 bar)
Virtual instrumentation
Battery BREAD BOARD
SENSORS
Throttle Position Sensor- Throttle position sensor will give the position of the throttle valve by which the control system is able to sense the requirement of the driver. Engine idling condition is also given by this system. Speed Sensor- Speed sensor will give the engine rpm to the system this will help the system to determine the timing of injection and ignition. Mass Flow Rate Sensor- mass flow rate sensor in placed in the inlet manifold. It will give the amount of fuel drawn into the cylinder per cycle. This will help the control system to determine the load on the engine. Atmospheric Air Temperature Sensor- Atmospheric air temperature sensor will give temperature of the air in the inlet. Inlet Pressure Sensor- inlet manifold pressure sensor is placed in the inlet manifold this will give the information about the suction created in the cylinder during the suction stroke. Lambda Sensor- Lambda sensor is an oxygen sensor which will give the amount of oxygen in the exhaust gas. This will give the feedback of the combustion to the system. This intern will control the amount of air and fuel for the combustion.
which will interface the sensors and give the signals to the actuators according to the program loaded. The entire system of operation is controlled by this system with the help of inputs from the sensors and the program loaded to it. It collects the various data from sensors like throttle position, inlet air pressure, mass flow rate of air, atmospheric air temperature, engine speed, load on engine, and control the entire operation of the engine. It is a closed loop system since it will get the feedback from the lambda sensor placed in the exhaust manifold which will give the amount of oxygen present in the exhaust gas. Amount of oxygen present in the exhaust gas will indicate the incomplete combustion so with respect to the input from the lambda sensor control system will evaluate the fuel injection timing and amount of fuel to be injected.
PORT TIMING
TDC position. The inlet port is closed 450 to 550 after the TDC. The exhaust port is opened 650 to 750 before BDC. The exhaust port is closed 650 to 750 after the BDC. The transfer port is opened 550 to 650 before BDC. The transfer port is closed 550 650 after TDC. The ignition takes place at 150 to 250 before TDC. The fuel injection starts at 700 to 750 after BDC. The fuel injection ends 750 to 800 after BDC
chamber, which is placed in the cylinder head. Only air is used for scavenging process. The injection of the fuel will begins just after the exhaust port is closed so the fuel is not wasted. The injection of the fuel is in high pressure so the atomisation of the fuel is good and also enhances thorough mixing of fuel before burning so the combustion will be complete. Electronic engine management system in implemented so the entire engine operation is precisely controlled electronically.
DIMENSIONS
CORE SIZE :
110*121mm^2
PORT SIZE: a) total length: 72mm outer diameter: 39mm b) inner step: 24 mm inner diameter: 22.5mm c) screw size : 2*6mm (as we have 2 screws) BORE SIZE:
42.6mm
STROKE LENGTH: 42mm PIN SIZE : pins 4 in number each having a size of 6mm PIN SIZE TOTAL LENGTH= 69mm+11mm=80mm( 4 pins we have) and (11mm end thread size). PISTON : a) piston diameter: 42.5mm piston length: 46.5mm MAX. TORQUE : 4.5Nm at 5500rpm MAX. POWER : 3.5bhp at 5000rpm
CALCULATIONS
PISTON DISPLACEMENT = = bore*bore*3.14*stroke 4 = 42.6 * 42.6 * 3.14 * 42 cc 4 * 1000 = 59.83 cc
COMPRESSION RATIO= = swept volume + clearance volume clearance volume = 980.98 + 141.06 141.06 = 7.96
MEAN EFFECTIVE PRESSURE (m.e.p) = horse power * 6500 Volume(in L) * Speed (rpm)
= 3.5 * 6500 0.0598 * 5000 = 75.95 bar
BRAKE POWER = 2 * 3.14 * N (speed in rpm) * Torque 60 = 2 * 3.14 * 5000 * 4.5 KW 60 = 2.355 KW
INDICATED POWER = mep* stroke length* area* no. of strokes* no.of cylinders KW 60 * 1000 = 75.95 * 42 * 1625.97 * 2 60 * 1000 = 0.172 KW
CONCLUSION
Thus implementing gasoline direct injection system in
two stroke petrol Engines along with the electronic engine management system we could achieve various advantages which will be competitive with the modern four stroke engine in all the ways like fuel efficiency, power developed and emission norms. The ultimate aim of this project is to bring the two stroke use again with satisfying the latest social and environmental requirements.
REFERENCE:
IC Engines- V. Ganesan
Automotive spark-ignited direct-injection gasoline
engine-F. Zhao, D.L. Harrington Sensors for Automotive Technology - J. Marek Gasoline Fuel Injection System - L-Jetronic Bosch Automotive Control Systems - Lars Nielsen