Beruflich Dokumente
Kultur Dokumente
AGENDA
Product Overview Function and Features 122
Mon
1.
2.
3. 4.
Tue
1. 2. 3. 4.
Wed
1.
2. 3.
FLC Replacement
Usefull SC commands Health Check
123
1 Functional Overview
1 Functional Overview
124
Operation System
external LAN
Craft Terminal
DCC Subsystem
9952 MBit/s 2488 MBit/s 622 MBit/s 155 MBit/s Gigabit Ethernet
STM-64
STM-16 STM-4 STM-1 o./el. GbEthernet 10GbEthernet I/O Subsystem Main Shelf
T1 T0
2 MBit/s
10 Gigabit Ethernet
Synchronisation Subsystem
T3/T6 1678 MCC Operation and Maintenance
All Rights Reserved Alcatel-Lucent 2007
T4/T5
Operation System
Customer DCN
Rack Lamps Q3 F Craft Terminal F Q3 RL Remote and Housekeeping Alarms RA/HK
DCR
DCC Server
EM
FLCSERV Disc
Backpanel LAN (ISSB)
Disc
FLCCONGI
SC
Matrix LO Copy A
SC
Matrix HO Copy A
Management Bus (to/from I/O boards)
SC
Matrix HO Copy B
SC
Matrix LO Copy B
I/O board
Assembler Assembler
HO Matrix active
LO Matrix active
copy A
copy A
I/O board
STM-1 el.
GbEthernet OED 1670 SM STM-4 STM-1 op. STM-1 el. 140 Mbit/s VSR Link boards I/O boards
I/O boards
I/O boards
2 Mbit/s
2 Mbit/s
Assembler: Function to perform the high order path termination and adaptation
1678 MCC Operation and Maintenance
All Rights Reserved Alcatel-Lucent 2007
OS
DCN
10/100BaseT (autosens, autoneg) 10/100BaseT (autosens,autoneg)
OSPF
IS-IS
DCR
to OED
DCC
EM
DCR
EM
to OED
F-IF
IP Address Rules
Product Overview Function and Features 129
dcrCong
(always configured on the active FLC) activeDCR(always configured on the active FLC) localCT (reserved address for installation purposes) dcnGateway (if DCN connection is via LAN) The address DCRHostId/32 is needed if IP-over-DCC and/or OSPF is used Used as local address of all unnumbered IP-over-DCC links Used as OSPF router Id The address GmreNode/32 is needed if GMRE is used Used for GMRE neighbor-to-neighbor communication
activeEM
NE Management
Product Overview Function and Features 1 2 10
Equipment Time
Synchronization (NTP)
Configuration
ssh)
Management (IP and OSI) possible via LAN or DCC
Internal and external traffic separated via VLAN setup on on-board LAN SWs
Default: No No
NSAP for Q3 communication always configured on active DCR Management may be via
Q3 NSAP address
RFC1006 activeDCR IP address
Stored in Backup
Persistency Check
tools PersSync
CS Configuration
start
CSConfigCLI m n s
(all SCs, LAX, Synth16 listed)
appl@emCongA3(appl)$ 0 | no valid line in Offset-File 1 | no valid line in Offset-File 2 | no valid line in Offset-File 3 | no valid line in Offset-File 4 | no valid line in Offset-File 5 | no valid line in Offset-File 6 | no valid line in Offset-File 7 | VHM | 5043 | S | 8 | PmMgr | 66 | S | 9 | SSU | 123 | S | 10 | MIB | 2742 | S | 11 | MIB | 2742 | S | 12 | MIB | 2742 | S | 13 | no valid line in Offset-File 14 |CSServer | 1 | S | 15 |CSServer | 1 | S | 16 |GMRE_PM | 1 | S | 17 |GMRE_MA | 1 | S | NVRAM access successfully ended!
PersSync
with with with with with with with
1 2 14
this index this index this index this index this index this index this index 0 | T | F | F |0K 66 | T | F | F |0K 38 | T | F | F |0K 0 | T | F | F |0K 0 | T | F | F |0K 0 | T | F | F |0K with this index 0 | T | F | F |0K 0 | T | F | F |0K 0 | T | F | F |0K 0 | T | F | F |0K
Basic Framework
start ll bfw*
CS parameters
Product Overview Function and Features 1 2 15
CS Parameters
Product Overview Function and Features 1 2 16
bash
tools setCSParams --file=/tmp/cs_params
CS parameters
Product Overview Function and Features 1 2 17
What is the meaning of files PrelimCSSRepository.xml and Installconfig.xml ? Active FLC SW Installation Standby FLC
Installconfig.xml
CSServer CSServer
PrelimCSSRepository.xml Installconfig.xml.processed
Gigabit Ethernet
Product Overview Function and Features 1 2 18
Ethernet/GFP-F Mapping
Product Overview Function and Features 1 2 19
Gigabit Ethernet
Product Overview Function and Features 1 2 20
Commissioning of 1GBE
Product Overview Function and Features 1 2 21
Follow commissioning docu for related release on NPI homepage or Customer docu homepage
Setup VCG using ISA port configuration menu Create unidirectional CrossConnection Loop from/to VC4vTTP of the 1GBE port on test Connect Ethernet Testset and check that L2 traffic is transported Test optical output power of GBE port and check that range is correct according to Commissioning protocol
Commissioning of 1GBE
Product Overview Function and Features
1 2 22
HO-ShelfController
Product Overview Function and Features 1 2 23
Boot up HO-SC
Boot of Rawloader
gs go (to coninue bootup) Trace using Serial cable on debug interface (38400 baud)
HO-ShelfController
Product Overview Function and Features 1 2 24
@(#)SEL Stuttgart SCM ID: SKY11-02L Released on Thu Jun 23 08:56:46 MEST 2005 Application software for SC1678mccX (SDH) R. 03.01.59 Based on generic SW R. 02.01.13 SC Protocol version: 11.6.1.0.0.0 SMX Protocol Version: 10.2.0.0.0.0
HO-ShelfController
Product Overview Function and Features 1 2 25
me 4 5
Difference between Timing Source <-> headed 10 MHz quartz decValue in ppb (parts per billion) -> / 1000 -> in ppm Alarm: SSF (Server Signal Failure) on port, SF (Signal Failure) on Timing Source (Sync View) FO (Frequency Offset) Reason: TimeSource not working or Hardware (faulty quartz), doublecheck with bsw command Action: repair/remove Timing Source or replace MX board
Check T0 Output
me 4 14
Difference between Systemclock (T0) of active Matrix (used) <-> Output Frequency (T0) of passive Matrix (not used) decValue * 0.0226 -> in ppm Alarm: SSM (Synchronization Source Missmatch) if Difference decValue > 16 (0.3616 ppm)
DCC in 1678MCC
Product Overview Function and Features 1 2 30
Capabilities
x DCC-M + 2 x DCC-R per STM-N board
Configurable
on ports 18
42
>DCC Application
Remote
2
x DCC-M per STM-N ring (east west) STM-N rings per 1678
21
IF/IB
Remote
1678 MCC Operation and Maintenance
DCC
Product Overview Function and Features 1 2 31
Ethernet
DCC
Management of NE2 is possible using NE1 as gateway NE for IP and OSI In EP dialog Gateway field is empty for NE2
DCC
Product Overview Function and Features 1 2 32
Configuration of OSPF interface (OSPF Router ID) Example: NE1 ip address: 10.10.133.12 -> NE1 OSPF Router Id: 10.10.254.133
DCC
Product Overview Function and Features 1 2 33
DCC
Product Overview Function and Features 1 2 34
Nr
Category
Mai
June
July
August
1 2 3 4 5
MX640/MX320/MX160 HW defect OED lost Question/Info Transmission Matrix issues, also Dafodil problem, OH-Link Others ICP/CSF/RTCSync/LanFailure Int.Comm
2 0 2 2 11
0 0 1 1 27
1 1 1 2 4
Solution
10
GBE / Question
0 RUM Synth16 1 LossOfPointer/SS 3 F/RMAF/RMBF Solved by Reset MX640 8 Solved by SW Reset of Lan-Failure, ICP, DCR, LAX or Process 5 CSF, NoRTCSync Restart GBE Modul defect / wrong SSF,CPE, interpretation by Sequence operator/interworking 3 Mismatch problem
Documentation
Product Overview Function and Features 1 2 38
http://slsvho
Documentation
Product Overview Function and Features 1 2 39
http://aww3.stgl.sel.alcatel.de/pub/tsddev/npi_scm/indus/index.html
Find out correct SW media
Documentation
Product Overview Function and Features 1 2 40
Documentation
Product Overview Function and Features 1 2 41
PSC link
Product Overview Function and Features 1 2 42
http://aww3.stgl.sel.alcatel.de/pub/tsddev/PSC
IDEA Database
Product Overview Function and Features 1 2 43
http://destgsweb59.ad1.ad.alcatel.com/idea/
1) Wrong implementation of Workaround in SW3.2P3 Caused by short occurance of MS-SSF (MS-AIS). When the workaround interferees then the STM1 sending LOF (Alarmliste: RDI auf MSTTP) Action: Remove/restore Board me 0 3 RMV B04 (Slot 3) RST B04 Board will loose ist traffic on board level for 30sec Fix: 3.2 P5 / R4.2 <- Beispiel
Mismatch db-Info of both SCs. Will be found by HealthCheck. Consequence is that HiOrder-Matrix-Switch leads to traffic interuption of 20sec on all Boards.
Action: Reset cold passive SC EPS switch HiOrder-Matrix (leads to 20s interuption on all boards) Reset passive SC Fix: 3.2 P3
3) Dafodil-ASIC hanging pointer processor Alarm: LossOfPointer (LOP) on 2nd/3rd TUG3; Degraded Signal on MSTTP, Unequipped on TU12 Action
4) Wrong values for register MOZART/WAGNER/CHOPIN Check registers on active HO-SC bsw bsw bsw bsw bsw bsw bsw bsw bsw bsw bsw bsw ispbRD ispbRD ispbRD ispbRD ispbRD ispbRD ispbRD ispbRD ispbRD ispbRD ispbRD ispbRD 9 2 140 10 2 140 9 3 140 10 3 140 9 5 283 9 6 283 9 7 283 9 8 283 10 5 283 10 6 283 10 7 283 10 8 283 If Overhead links are not correct the HiOrder-Matrix-Switch will lead to power reset on several or on all IO-Boards and to a traffic interuption on these boards
Result:
Action:
Remove/restore passive HO-Matrix reset -p Fix: 3.2 P4
1678 MCC Operation and Maintenance
All Rights Reserved Alcatel-Lucent 2007
1)
All SC/LAX Interfaces pingable from both EM and DCR ? ping ping ping ping ping ping ping ping 100.1.10.1 (HO-MX left) 100.1.10.20 (HO-MX left) 100.1.11.1 (HO-MX right ) 100.1.11.20 (HO-MX right) 100.1.18.1 (left LAX) 100.1.18.20 (left LAX) 100.1.19.1(right LAX) 100.1.19.20 (right LAX)
2) Interfaces internally connected to process ICHdlr ? tools ./statICHdrl c hoSlca_1_dcrs hoSlcb_1_dcrs loSlca_1_dcrs loSlca_1_dcrs loSlca_1_dcrs
1678 MCC Operation and Maintenance
3)
Alarm ICP not active for process ICHdlr ? log tail f scSwitch.log
24.09.2007 08:11:18 Alarm LSSC/CSF = 1 : HoMx (1, 4, 10, 0, 0) passive: HoMx (1, 4, 11, 0, 0) 24.09.2007 08:13:51 : HoMx (1, 4, 10, 0, 0) set EquState: e_EquState_Downloading=>e_EquState_Active 24.09.2007 08:13:51 Alarm LSSC/CSF = 0 : HoMx (1, 4, 10, 0, 0) passive: HoMx (1, 4, 11, 0, 0)
4) Each LAX is loaded correctly ? telnet 100.1.18.1 Telnet+> db role Local Role Equipment State Software State Database state
1678 MCC Operation and Maintenance
= = = =
start CSConfigCLI m s n
hoSlca_1_dcrs|100.1.10.1|100.1.203.4|00:00:00:00:00:0A|MX640GEA|1_4_10 hoSlca_1_dcrc|100.1.10.20|100.1.120.2|00:00:00:00:00:0A|MX640GEA|1_4_10 hoSlcb_1_dcrs|100.1.11.1|100.1.203.4|00:00:00:00:00:0B|MX640GEB|1_4_11 hoSlcb_1_dcrc|100.1.11.20|100.1.120.2|00:00:00:00:00:0B|MX640GEB|1_4_11 loSlca_1_dcrs|100.1.12.1|100.1.203.4|00:00:00:00:00:0C|LAX40A|1_4_12 loSlca_1_dcrc|100.1.12.20|100.1.120.2|00:00:00:00:00:0C|LAX40A|1_4_12 loSlcb_1_dcrs|100.1.13.1|100.1.203.4|00:00:00:00:00:0D|LAX40B|1_4_13 loSlcb_1_dcrc|100.1.13.20|100.1.120.2|00:00:00:00:00:0D|LAX40B|1_4_13
6)
view /etc/hosts
Craft Terminal
Product Overview Function and Features 1 2 51
FLC Congi
Craft Terminal
FLC Congi
Craft Terminal
-> Use Craft Terminal as PCCT via LAN is independent from state of FLC
CraftTerminal
Product Overview Function and Features 1 2 52
Start CT Appl.
-> Do not forget to declare the PCCT User in EP Dialog ! PCCT1 NSAP 540072872203010010088010 TSEL: 1102 SSEL: 00 PSEL: 1D
1678 MCC Operation and Maintenance
All Rights Reserved Alcatel-Lucent 2007
CraftTerminal
Product Overview Function and Features 1 2 53
Delete Persistency
Product Overview Function and Features 1 2 54
FLC Replacement 1) 2) 3) Install new FLC with the same SW, IP and network parameters like on active FLC Start application on newly installed FLC Check processes on this FLC. The FLC should become passive [ Raise Equipment Provisioning, CS parameters and Click OK ] After Supervision comes back the Reinitialize of CS Server has written all necessary Persistency data onto passive FLC. Check this with command PersSync and check CS Persistency on passive FLC:
> start
> CSConfigCLI m n s > tools
> PersSync
1678 MCC Operation and Maintenance
All Rights Reserved Alcatel-Lucent 2007
Usefull SC commands
Product Overview Function and Features 1 2 56
Request SC EPS status Check the EPS state of the SCs. In case SF for failure the EPS state release is not possible and the SCs remain with expression mark on GUI.
telnet <IP active SC> me 0 5 Matrix Pg.B10-AUTO_SWITCH pu.B09-SF pu.B10-SF-ACT EPS data: (bm_epsSW_status_t bm_privateEpsData[bSlot]=1=traffic on spare) 0 . 1 . 2 . 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
[EPS pg_status]
pu.B09-OK-ACT pu.B10-OK
Usefull SC commands
Show status of boards Product Overview Function and Features
1 2 57
Sometimes e.g. in ISU it is necessary to display the board status, in case a FPGA download will be performed than the status fpga dwnld will be displayed.
me 0 2 Slot Card Number Status 01->IN Slot number (0... (descrNum.) | S1..26 | A0..A3 B0..B21 | Ex-y | -1 all | Quit):-1 [00 BA01 CT01 B00] normal active [01 BA02 CT02 B01] undef idle 02->OUT [02 BA03 CT03 B02] undef idle 03->OUT [03 BA04 CT04 B03] undef idle 04->OUT [04 BA05 CT05 B04] undef idle 05->OUT [05 BA06 CT06 B05] normal active 06->IN [08 BA09 CT09 B08] normal active 09->IN [09 BA10 CT10 B09] normal active 10->IN [10 BA11 CT11 B10] normal active 10->IN [11 BA12 CT12 B11] normal InsSbyMain 11->IN [12 BA13 CT13 B12] normal InsActSpare 12->IN [13 BA14 CT14 B13] normal active 13->IN [14 BA15 CT15 B14] normal active 14->IN [15 BA16 CT16 B15] normal active 15->IN [16 BA17 CT17 B16] normal active 16->IN [17 BA18 CT18 B17] normal active 17->IN [18 BA19 CT19 B18] undef idle 18->OUT [19 BA20 CT20 B19] normal active 19->IN [20 BA21 CT21 B20] normal active 20->IN [21 BA22 CT22 B21] normal active 21->IN [22 BA23 CT23 A00] normal active 255->IN [23 BA24 CT24 A01] normal active 255->IN [24 BA25 CT25 A02] normal active 255->IN [25 BA26 CT26 A03] normal active 255->IN
1678 MCC Operation and Maintenance
Usefull SC commands
Product Overview Function and Features 1 2 58
Check CRU Status and Clock source The CRU mode must be SC_SYNC_LOCKED before SLC switchover and before testing. That means that a clock source is selected. In the example the CRU mode is not ok, probably no clock source is connected or configured me 4 2
...
Usefull SC commands
Product Overview Function and Features 1 2 59
Check SC traces The SC traces are usefull to find out if the SC behaves suspicious, board reset was performed or a SLC switchover was performed without an obvious reason. The latest traces are recorded. me 1 15
[SC traces]
SC AS 8 ../src/as_rav_blk.c:3204: REPEAT #2 failed to read RAVEL SW version on board with BA 0x2100 (at address 0x2100) SC AS 8 ../src/as_rav_blk.c:3204: REPEAT #3 failed to read RAVEL SW version on board with BA 0x2100 (at address 0x2100) SC AS 8 ../src/as_rav_blk.c:3204: REPEAT #4 failed to read RAVEL SW version
Usefull SC commands
Product Overview Function and Features 1 2 60
Reset remote SC If the partner SLC should be resetted in case of being unavailable use following command. This can be done when e.g the active SLC is not pingable anymore (CSF alarm). Then perform Cold start. me 1 18
### RESTART REMOTE SC ### 1) KS_POWER_ON_START 2) KS_COLD_START 3) KS_WARM_START 4) KS_NO_RESTART 0) Return to Menu
Usefull SC commands
Product Overview Function and Features 1 2 61
Check ispbs error counters The ispbs is a bus for communication between the SCs and the intelligent boards in the shelf. In case of error counters are bigger than 000FF the bus is disturbed. This can be a result of a faulty board or a faulty Busterm board.
Telnet+> ispbs ----------------------------ISPB-BUS device-driver status ----------------------------- ISPB-read ABE DBE RDY ACK NDN NRS operation performed: = 0x090D7195 error error error error error error count count count count count count = = = = = = 0x00000000 0x00000000 0x00000000 0x000001C2 0x00000000 0x00000000
operation performed: = 0x001C7679 error count = 0x00000000 error count = 0x00000000 error count = 0x00000000 error count = 0x00000000 error count = 0x00000000 error count = 0x00000000
Backup / Restore
# run checkedPersBackup tool every Mon and Thu at 00:35 UTC 35 0 * * 1,4 cd ~; /usr/bin/perl ./checkedPersBackup.pl >> ~/checkPersistency.log 2>&1
:wq
1678 MCC Operation and Maintenance
All Rights Reserved Alcatel-Lucent 2007