Beruflich Dokumente
Kultur Dokumente
www.huawei.com
Huawei Confidential
Preface
The
Huawei Confidential
Page 2
References
OptiX
description documentation
OptiX
description documentation
Huawei Confidential
Page 3
Target
After
Hardware
Functions
Huawei Confidential
Page 4
Contents
Network Position and Networking
Application
System Architecture
Hardware Structure
Boards
Huawei Confidential
Page 5
Network Position
The OptiX RTN 900 is a new generation split microwave transmission system developed by Huawei. It
can provide a seamless microwave transmission solution for a mobile communication network or
private network.
The OptiX RTN 900 products are available in two types: OptiX RTN 910 and OptiX RTN 950. The IDU
of the OptiX RTN 910 is 1U high and supports one or two IF boards. The IDU of the OptiX RTN 950 is
2U high and supports one to six IF boards. The users can choose an appropriate type based on the
actual requirements.
The OptiX RTN 900 provides several types of service interfaces and facilitates installation and flexible
configuration. It can provide a solution that is integrated with the TDM microwave, Hybrid microwave,
and Packet microwave based on the network requirements. It supports the smooth upgrade from the
TDM microwave to the Hybrid microwave, and from the Hybrid microwave to the Packet microwave.
The solution can evolve based on the service changes that occur due to radio mobile network
evolution. Thus, this solution can meet the transmission requirements of not only 2G and 3G networks,
but also future LTE and 4G networks.
RTN 900 V1R1 support pure packet microwave, and RTN 900 V1R2 support TDM microwave and
Hybrid microwave.
Huawei Confidential
Page 6
E1
E1
E1
E1
STM-1/E1
E1
Regional Backhaul
Network
E1
E1
E1
E1
OptiX
RTN
900
E1
BTS
BSC
When the OptiX RTN 910 supports the microwave transmission in three directions or more, you can adopt
the NE cascading mode or use the OptiX RTN 950, which has more powerful functions.
Huawei Confidential
Page 7
FE
E1
E1
FE
E1
E1
STM-1/E1
Regional Backhaul
Network
E1
FE/GE
GE
E1
FE
E1
OptiX
RTN
900
NodeB
BTS
RNC
BSC
When the OptiX RTN 910 supports the microwave transmission in three directions or more, you can adopt
the NE cascading mode or use the OptiX RTN 950, which has more powerful functions.
Huawei Confidential
Page 8
Contents
Network Position and Networking
Application
System Architecture
Hardware Structure
Boards
Huawei Confidential
Page 9
service interface unit, timeslot cross-connect unit, IF unit, control unit, clock unit, auxiliary
interface unit, fan unit, power unit, and ODU.
Service
interface
unit
Accesses E1 signals.
Accesses STM-1 signals.
Service
switching
unit
IF unit
Huawei Confidential
Page 10
service interface unit, timeslot cross-connect unit, packet switching unit, IF unit, control
unit, clock unit, auxiliary interface unit, fan unit, power unit, and ODU.
Service
interface
unit
Accesses E1 signals
Accesses STM-1 signals
Accesses Ethernet signals.
Timeslot
crossconnect
unit
Packet
switching
unit
IF unit
Huawei Confidential
Page 11
SDH/PDH Microwave
Hybrid Microwave
Huawei Confidential
Page 12
SDH/PDH Microwave
Hybrid Microwave
Huawei Confidential
Page 13
Contents
Network Position and Networking
Application
System Architecture
Hardware Structure
Boards
Huawei Confidential
Page 14
Hardware Structure
RTN 900 series
Universal AOC
IDU 910
IDU 950
Huawei Confidential
Page 15
Paired slots
for housing the service
interface boards or IF boards
Huawei Confidential
Page 16
are supported.
The 1+1 HSB/SD/FD is supported.
The N+0 configuration (N5) is supported.
The N+1 configuration (N5) is supported.
The XPIC is supported.
Paired slots
Paired slots
Power(1+1)
Paired slots
"EXT" represents an extended slot, which can house an IF board or a service interface board.
All the boards except the power supply board support hot swapping.
Huawei Confidential
Page 17
Contents
Network Position and Networking
Application
System Architecture
Hardware Structure
Boards
Huawei Confidential
Page 18
Contents
Boards
CSTA
CST
Huawei Confidential
Page 19
communication, and clock processing functions. In addition, the CSTA provides PDH/SDH
service interfaces, auxiliary interfaces, and management interfaces.
Grooms service signals between boards. Supports full time division cross-connections at the VC-
Huawei Confidential
Page 20
CSTAFunctional Modules
Functional modules:
The CSTA comprises the
Huawei Confidential
Page 21
CSTA boards are inserted in slots 1 and 2 in the IDU 910 chassis.
The CXPAR/CXPBR boards can be inserted only in slots 1 and 2 in the IDU 910 chassis.
The CXPAR/CXPBR boards cannot be inserted in the IDU 950 chassis.
According to the functional units, the CSTA is mapped into the logical system control and
communication board (CSTA), logical auxiliary and management board (AUX), and
logical service boards (SL1D and SP3S) on the NMS.
Huawei Confidential
Page 22
CSTA Interfaces
external clock/ Bypass E1
service interface
Buttons
Indicators
NE cascade
interface
NM interface/NM
serial interface
Orderwire phone
interface (RJ-45
connector)
Synchronous/A
synchronous
data interface
Alarm input/output
interface
STM-1 optical
interfaces
E1 (1-16)
interface
NOTE:
The external clock interface and wayside E1 interface are combined into one interface. This interface can transparently transmit
the DCC byte, orderwire overhead byte, and synchronous/asynchronous data service overhead byte. One interface, however,
can implement only one of the three functions: external clock interface, wayside E1 service, and transparent transmission of the
overhead byte.
The 64 kbit/s synchronous data interface can transparently transmit the orderwire byte. One interface, however, can implement
only one of the two functions: 64 kbit/s synchronous data interface and transparent transmission of the orderwire byte.
Huawei Confidential
Page 23
CSTAIndicators
Indicator
Color
State
Description
On (green)
STAT indicator
On (red)
Off
PROG indicator
On (green)
On (red)
On for 100 ms
(green) and off for
100 ms repeatedly
On for 300 ms
(green) and off for
300 ms repeatedly
Huawei Confidential
Page 24
CSTAIndicators
Indicator
Color
SYNC indicator
State
On (green)
On (red)
On (green)
SRV indicator
On (red)
On (yellow)
Off
On (red)
LOS 1
Off
On (red)
LOS 2
Off
Description
Huawei Confidential
Page 25
CSTAButtons
Button
Description
CF RCV button
RST button
Huawei Confidential
Page 26
The CST provides the time division cross-connection, system control and communication,
and clock processing functions. In addition, the CST provides the auxiliary interfaces and
management interfaces.
Grooms TDM service signals between boards. Supports full time division cross-connections at the
Huawei Confidential
Page 27
Huawei Confidential
Page 28
CSTSlot allocation
The CST boards can be inserted in slots 7 and 8 and form a 1+1 protection group.
Note
The CST boards can be inserted only in slots 7 and 8 in the IDU 950 chassis and form a
Huawei Confidential
Page 29
CST Interfaces
Indicators
Button
NM cascade
interface
External clock
interface/The first time
interface/The wayside E1
interface
NM interface/NM
serial interface
Note
The external clock interface and wayside E1 interface are combined into one interface. This interface can transparently
transmit the DCC byte, orderwire overhead byte, and synchronous/asynchronous data service overhead byte. One interface,
however, can implement only one of the three functions: external clock interface, wayside E1 service, and transparent
transmission of the overhead byte.
Huawei Confidential
Page 30
CSTIndicators
Indicator
Color
State
Description
On (green)
STAT indicator
On (red)
Off
PROG indicator
On (green)
On (red)
On for 100 ms
(green) and off for
100 ms repeatedly
On for 300 ms
(green) and off for
300 ms repeatedly
Huawei Confidential
Page 31
CSTIndicators
Indicator
Color
SYNC indicator
State
On (green)
On (red)
On (green)
SRV indicator
Description
The clock is operating normally.
The clock source is lost or is switched.
The services are working normally and no
alarms occur in the services.
On (red)
On (yellow)
Off
On (green)
ACT
Off
Huawei Confidential
Page 32
CSTButtons
Button
Description
CF RCV button
RST button
Huawei Confidential
Page 33
Contents
Boards
TDM system control, cross-connect, and timing board
Hybrid system control, cross-connect, and timing board
CSHA/CSHB/CSHC
CSH
IF board
Service interface board
Auxiliary and management interface board
Power supply board and fan board
Huawei Confidential
Page 34
The CSHA/CSHB/CSHC provides the 4.2 Gbit/s packet switching, full time division cross-connection, system control
and communication, and clock processing functions. In addition, the CSHA/CSHB/CSHC provides FE/GE interfaces,
PDH/SDH interfaces, auxiliary interfaces, and management interfaces.
Support Packet Switch, Provides the 4.2 Gbit/s packet switching capability.
Supports full time division cross-connections at the VC-12, VC-3, or VC-4 level, which are equivalent to 8x8 VC4s.
Provides TDM service interfaces: The CSHA provides sixteen 75-ohm/120-ohm E1 data interfaces. The CSHB
provides thirty-two 75-ohm/120-ohm E1 data interfaces. The CSHC supports sixteen 75-ohm/120-ohm E1 data
interfaces and two STM-1 optical interfaces. The two STM-1 optical interfaces use the SFP optical modules.
Provides Eth service interfaces: The CSHA provides two FE electrical interfaces and two GE electrical
interfaces. The two GE electrical interfaces can also transmit FE electrical signals. The CSHB provides two FE
electrical interfaces and two GE electrical interfaces. The two GE electrical interfaces can also transmit FE
electrical signals. The CSHC provides two FE electrical interfaces and two GE optical interfaces. The two GE
optical interfaces use the SFP optical modules.
Provides one input and one output of the external clock. / Bypass E1 service interface.
Huawei Confidential
Page 35
The differences between the CSHA, CSHB, and CSHC are with regard to the types and number
of service interfaces.
Huawei Confidential
Page 36
Huawei Confidential
Page 37
Huawei Confidential
Page 38
CSHA/ CSHB/CSHCInterfaces
Button
Indicators
NE cascade interface
NM interface/NM
serial interface
CSHB
CSHC
Synchronous/
Asynchronous
data interface
2*FE
interfaces
2*GE interfaces
Alarm
input/output
interface
E1 (1-16) interface
FE service
interfaces
FE service
interfaces
CSHA
GE service
interface
GE service
interfaces
Huawei Confidential
E1 1 16,17~32
STM-1 service
interfaces
Page 39
E1 1 16
CSHA/ CSHB/CSHCIndicators
Indicator
Color
State
Description
On (green)
STAT indicator
On (red)
Off
PROG indicator
On (green)
On (red)
On for 100 ms
(green) and off for
100 ms repeatedly
On for 300 ms
(green) and off for
300 ms repeatedly
Huawei Confidential
Page 40
CSHA/ CSHB/CSHCIndicators
Indicator
Color
SYNC indicator
State
On (green)
On (red)
On (green)
SRV indicator
On (red)
On (yellow)
Off
Description
Huawei Confidential
Page 41
CSHA/ CSHB/CSHCIndicators
Indicator
LINK 1
ACT 1
LINK 2
ACT 2
LOS 1
LOS 2
Color
State
Description
On (green)
Off
On or blinking
(yellow)
Off
On (green)
Off
On or blinking
(yellow)
Off
On (red)
Off
On (red)
Off
Huawei Confidential
Page 42
CSHA/ CSHB/CSHCButtons
Button
Description
CF RCV button
RST button
Huawei Confidential
Page 43
The CSH provides the 10 Gbit/s packet switching, full time division cross-connection,
system control and communication, and clock processing functions. In addition, the CSH
provides auxiliary interfaces and management interfaces.
Support Packet Switch, Provides the 10 Gbit/s packet switching capability.
Supports full time division cross-connections at the VC-12, VC-3, or VC-4 level,
interface.
Huawei Confidential
Page 44
Huawei Confidential
Page 45
CSHSlot Allocation
The CSH boards can be inserted in slots 7 and 8 and form a 1+1 protection group.
The CST boards can be inserted only in slots 7 and 8 in the IDU 950 chassis and form a
Huawei Confidential
Page 46
NM
interface/NM
serial interface
External clock/time
interface /The
wayside E1 interface
NE cascade
interface
CF RCV button: used to restore the configuration data from the CF card. After you press the CF RCV button
for 5 seconds, the equipment automatically restores the configuration data from the CF card.
RST button: used for warm reset on the board. When you press the RST button and then release it, a warm
reset is performed on the board.
Huawei Confidential
Page 47
Contents
Boards
TDM system control, cross-connect, and timing board
Hybrid system control, cross-connect, and timing board
CSHA/CSHB/CSHC
CSH
IF board
IF1
IFU2
IFX2
Huawei Confidential
Page 48
The IF1 is a medium-capacity SDH IF board . The IF1 board has the following functions
IF processing functions:
Maps SDH and PDH service signals into microwave frame signals.
Codes and decodes microwave frame signals.
Modulates and demodulates microwave frame signals
Modulates and demodulates ODU control signals
Combines and splits service signals, ODU control signals, and -48 V power
supplies.
Support ATPC Automatic Transmit Power Control function.
Protection Processing functions:
Support 1+1 HSB/FD/SD protection.
Support 1+1 FD/SD hitless switching.
Support N+1 protection.
Huawei Confidential
Page 49
Huawei Confidential
Page 50
the ODU and supplies the required -48 V power to the ODU.
IDU 910:
The IF1 board can be inserted in
slot 3 or slot 4.
IDU 950:
The IF1 board can be inserted in
any of slots 1 to 6.
To configure a 1+1 FD/SD
protection group, the IFE2
boards must be inserted in
paired slots.
The paired slots supported by
the IDU 950 are as follows: (slot
1, slot 2), (slot 3, slot 5), and
(slot 4, slot 6).
Slot allocation priority : Slots 3
and 5 > slots 4 and 6 > slots 1
and 2
HUAWEI TECHNOLOGIES CO., LTD.
IDU 910
IDU 950
Huawei Confidential
Page 51
IF interface (TNC)
ODU switch
When the switch is set to "O", it
indicates that the circuit is open.
When the switch is set to "I", it
indicates that the circuit is
closed.
Indicators:
Working status indicator (STAT) two colors (red and
green)
Status indicator (SRV) three colors (red, green, and
yellow)
Radio link status indicator (LINK) one color (green)
ODU status indicator (ODU) three colors (red, green, and
yellow)
Remote end status indicator (RMT) one color (yellow)
Protection status indicator (ACT) one color (green)
Huawei Confidential
Page 52
IF1Indicators
Indicator
Color
State
On (green)
STAT
indicator
On (red)
Off
On (green)
SRV
indicator
ACT
indicator
On (yellow)
On (green)
On (yellow)
On for 300 ms
(yellow) and off for
300 ms repeatedly
RMT
indicator
On (red)
On (red)
ODU
indicator
Description
On (yellow)
On (green)
Off
Page 53
The IFU2 is a general IF board, which can support the Hybrid microwave transmission and Packet
microwave transmission at the same time. In this version, the IFU2 supports only the Hybrid microwave
transmission.
Supports the Hybrid microwave frames, and supports the pure transmission of E1 or Ethernet
256QAM.
Maps service signals into microwave frame signals.
Codes and decodes microwave frame signals.
Modulates and demodulates microwave frame signals.
Modulates and demodulates ODU control signals.
Combines and splits service signals, ODU control signals, and -48 V power supplies.
Huawei Confidential
Page 54
Huawei Confidential
Page 55
channel to the ODU, and supplies the required -48 V power to the ODU.
IDU 910:
The IFU2 board can be inserted
in slot 3 or slot 4.
IDU 910
IDU 950:
The IFU2 board can be inserted
in any of slots 1 to 6.
To configure a 1+1 FD/SD
protection group, the IFE2
boards must be inserted in
paired slots.
The paired slots supported by
the IDU 950 are as follows: (slot
1, slot 2), (slot 3, slot 5), and
(slot 4, slot 6).
Slot allocation priority : Slots 3
and 5 > slots 4 and 6 > slots 1
and 2
HUAWEI TECHNOLOGIES CO., LTD.
IDU 950
Huawei Confidential
Page 56
IF interface (TNC)
ODU switch
When the switch is set to "O", it
indicates that the circuit is open.
When the switch is set to "I", it
indicates that the circuit is closed.
Indicators:
Working status indicator (STAT) two colors (red and
green)
Status indicator (SRV) three colors (red, green, and
yellow)
Radio link status indicator (LINK) one color (green)
ODU status indicator (ODU) three colors (red, green,
and yellow)
Remote end status indicator (RMT) one color (yellow)
Protection status indicator (ACT) one color (green)
Huawei Confidential
Page 57
SDH microwave. In this version, the IFX2 supports only the Hybrid microwave transmission.
Supports the XPIC function, provides the XPIC input and output interfaces, and supports the
mode of 256QAM.
Maps service signals into microwave frame signals.
Codes and decodes microwave frame signals.
Modulates and demodulates microwave frame signals.
Modulates and demodulates ODU control signals.
Combines and splits service signals, ODU control signals, and -48 V power supplies.
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 58
Huawei Confidential
Page 59
IDU 950
Huawei Confidential
Page 60
ODU switch
When the switch is set
to "O", it indicates that the
circuit is open. When the
switch is set to "I", it
indicates that the circuit is
closed.
XPIC signal
interfaces
IF interface (TNC)
Indicators:
XPIC input signal indicator XPIC two colors (red
and green).
Working status indicator (STAT) two colors (red and green)
Status indicator (SRV) three colors (red, green, and
yellow)
Radio link status indicator (LINK) one color (green)
ODU status indicator (ODU) three colors (red, green, and
yellow)
Remote end status indicator (RMT) one color (yellow)
Protection status indicator (ACT) one color (green)
Huawei Confidential
Page 61
1
The ODU-PWR switch is equipped
with a lockup device. To turn on or
turn off the switch, you need to first
pull the switch lever outwards
slightly.
Huawei Confidential
Page 62
2
When the ODU switch is set to I, do
not insert or remove the IF cable.
Huawei Confidential
Page 63
IF signal
ODU
management
signal
Performance
350
140
Impedance (ohm)
50
Modulation mode
ASK
5.5
10
Huawei Confidential
Page 64
Contents
Boards
TDM system control, cross-connect, and timing board
Hybrid system control, cross-connect, and timing board
CSHA/CSHB/CSHC
CSH
IF board
IF1
IFU2
IFX2
Service interface board
EM6T/EM6F
SL1D
SP3S/SP3D
AUX
Huawei Confidential
Page 65
interfaces and two GE interfaces. The EM6T has similar functions to the EM6F. The only
difference is as follows: the GE interfaces on the EM6T always function as electrical
interfaces whereas the GE interfaces on the EM6F use the SFP modules and therefore
can function as two optical or electrical interfaces. The GE electrical interfaces on the
EM6F and the EM6T are compatible with the FE electrical interfaces.
The EM6T/EM6F accesses, processes, and aggregates four FE signals and two GE
Huawei Confidential
Page 66
Huawei Confidential
Page 67
EM6T/EM6FSlot Allocation
IDU 910:
The EM6T/EM6F board can
be inserted in slot 3 or slot 4.
IDU 910
IDU 950:
The EM6T/EM6F board can be
inserted in any of slots 1 to 6.
Slot allocation priority Slots 4
and 6 > slots 1 and 2 > slots 3
and 5
IDU 950
Huawei Confidential
Page 68
EM6T/EM6FFront Panel
GE
Indicators
interfacesRJ45
GE
interfaces-LC
FE interfaces-
RJ45
GE electrical interfaces on the front panel of the EM6T are compatible with the FE interfaces. The GE
interfaces on the front panel of the EM6F use pluggable SFP optical modules.
The FE electrical interfaces and GE electrical interfaces support the MDI and MDI-X adaptation modes.
The FE interfaces support 10M full duplex, 10M half duplex, 100M full duplex, 100M half duplex, and
auto-negotiation.
The GE electrical interfaces support 10M full duplex, 10M half duplex, 100M full duplex, 100M half
duplex, 1000M full duplex, and auto-negotiation.
Huawei Confidential
Page 69
The SL1D is an SDH dual-port STM-1 board. The SL1D transmits and receives 2xSTM-1
optical signals.
Supports the automatic laser shutdown (ALS) function.
Supports SNCP and LMSP.
Supports the inloop and outloop over optical interfaces.
Supports the outloop on VC-4 paths.
Supports the warm reset and cold reset on the board.
Supports the query of the board manufacturing information.
Supports the in-service upgrade of the FPGA.
Huawei Confidential
Page 70
Huawei Confidential
Page 71
SL1DSlot Allocation
IDU 910:
The SL1D board can be
inserted in slot 3 or slot 4.
IDU 910
IDU 950:
The SL1D board can be
inserted in any of slots 1 to 6.
Slot allocation priority Slots 4
and 6 > slots 1 and 2 > slots 3
and 5.
IDU 950
Huawei Confidential
Page 72
SL1DInterfaces
Indicators:
Working status indicator (STAT) two
colors (red and green)
Status indicator (SRV) three colors
(red, green, and yellow)
LOS1/LOS2: Whether the optical
interface have the R_LOS alarm.
STM-
1interface-LC
The type of the SFP optical module equipped on the SL1D, provides Ie-1 Multi-mode,
Huawei Confidential
Page 73
The SP3S is a 16xE1 75-ohm/120-ohm tributary board. The SP3D is a 32xE1 75-
code of the bar code. In the bar code, the board feature code is the number next to the
board name.
Board Feature Code
120
75
Huawei Confidential
Page 74
Huawei Confidential
Page 75
IDU 910:
The SP3S/SP3D board can
be inserted in slot 3 or slot 4.
IDU 910
IDU 950:
The SP3S/SP3D board can be
inserted in any of slots 1 to 6.
Slot allocation priority Slots 4
and 6 > slots 1 and 2 > slots 3
and 5.
IDU 950
Huawei Confidential
Page 76
SP3S/SP3D Interfaces
Indicators:
Working status indicator (STAT) two
colors (red and green)
Status indicator (SRV) three colors
(red, green, and yellow)
E1 interface
NOTE:
In the case of the OptiX RTN 900, only the ports 1-16 and 22-37 of the SP3D interface are
used. Ports 1-16 correspond to E1 signals 1-16 and ports 22-37 correspond to E1 signals 1732.
Huawei Confidential
Page 77
The AUX is the auxiliary and management interface board of the OptiX RTN 950 V1R2.
one orderwire interface, one synchronous data interface, one asynchronous data
interface, and one four-input/two-output external alarm interface.
Provides one orderwire interface.
Provides one 64 kbit/s synchronous transparent data interface.
Supports one 19.2 kbit/s asynchronous transparent data interface.
Supports the input of four channels of external alarms.
Supports the output of two channels of external alarms.
Supports hot swapping.
Supports the detection of the board power supply.
Huawei Confidential
Page 78
Huawei Confidential
Page 79
AUX Interfaces
Synchronous/
Orderwire
Alarm
Asynchronous
data interface
phone
output
Indicators:
Working status indicator (STAT) two
colors (red and green)
Status indicator (SRV) three colors
(red, green, and yellow)
Alarm input
The OptiX RTN equipment also supports the orderwire group call function. For example, when an OptiX RTN
equipment calls the number of 888, the orderwire group call number, all the OptiX RTN equipment orderwire phones
in the orderwire subnet ring until a phone is answered. Then, a point-to-point orderwire phone call is established.
Huawei Confidential
Page 80
AUXSlot Allocation
IDU 950
The AUX board can be inserted in any of slots 1 to 6.
An NE can house only one AUX board.
The AUX board cannot be installed in the IDU 910 chassis.
Huawei Confidential
Page 81
Contents
Boards
TDM system control, cross-connect, and timing board
Hybrid system control, cross-connect, and timing board
CSHA/CSHB/CSHC
CSH
IF board
IF1
IFU2
IFX2
Service interface board
Auxiliary and management interface board
Power supply board and fan board
PIU
FAN
Huawei Confidential
Page 82
Functional
Version
Description
Valid Slot
PIU
TNC1
PIU
TND1
IDU 910:
The PIU board whose functional
version is TNC1 is fixedly inserted
in slot 5. The two accessed power
supplies function as a hot backup
for each other.
IDU 950:
The PIU boards that have the
functional version of TND1 are
fixedly inserted in slot 9 and slot 10.
The two PIU boards function as a hot
backup for each other.
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 83
BGND power
input interface
TND1 PIU
48 V power
input interface
BGND power
input interface
48 V power
input interface
Huawei Confidential
Page 84
Board
Functional
Version
Description
Valid Slot
FAN
TNC1
FAN
TND1
IDU 910:
The FAN board whose functional
version is TNC1 is fixedly inserted in
slot 6.
Accesses one +12 V power supply for
driving three fans, each of which
consumes 6 W power.
IDU 950:
The FAN board whose functional version
is TND1 is fixedly inserted in slot 11.
Accesses two +12 V power supplies for
driving six fans, each of which consumes
6 W power.
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Confidential
Page 85
42CM
Indicator
Color
State
Green
FAN indicator
CRIT
indicator
MAJ indicator
MIN alarm
Red
Off
Red
Orange
Yellow
86.2CM
Description
Huawei Confidential
Page 86
Summary
CSHA/CSHB/CSHC/CSH
IF board: IF1 IFU2 IFX2
Service interface board :
EM6T/EM6F SL1D SP3S/SP3D
Auxiliary and management interface board : AUX
Power supply board and fan board : PIU FAN
Huawei Confidential
Page 87
Weight (kg)
CSTA
1.079 kg
19W
CSHA
1.110 kg
19W
CSHB
1.158 kg
22W
CSHC
1.129 kg
20W
CST
0.720 kg
21W
CSH
0.740 kg
25W
IF1
0.720 kg
8W
IFU2
0.790 kg
22W
IFX2
0.796 kg
24W
EM6T/EM6F
0.370 kg / 0.382kg
12W
SL1D
0.296 kg
3W
SP3S
0.544 kg
5W
SP3D
0.644 kg
10W
AUX
0.270 kg
2.1W
PIU
0.120 kg
0.5W
FAN
0.200kg
Huawei Confidential
Page 88
Thank you
www.huawei.com