0 Bewertungen0% fanden dieses Dokument nützlich (0 Abstimmungen)
44 Ansichten2 Seiten
(1) The document provides guidelines for optimizing 3G cell sites with high SHO overhead, including cells with SHO overhead greater than 50%, TP greater than ISD by more than 20%, and cells not meeting downtilt checks.
(2) The guidelines include performing RET to optimize maximum mechanical tilt based on height and ISD, modifying SHO parameters like trigtime1B and trigtime1A to still meet OSS KPI targets, and addressing bad spot coverage and pilot pollution first before applying these guidelines.
(3) For new 3G sites with SHO overhead below 60% after applying the guidelines, exemption can be made if target coverage conflicts with the rules. The multi-sector re-azimuth guidelines ensure
(1) The document provides guidelines for optimizing 3G cell sites with high SHO overhead, including cells with SHO overhead greater than 50%, TP greater than ISD by more than 20%, and cells not meeting downtilt checks.
(2) The guidelines include performing RET to optimize maximum mechanical tilt based on height and ISD, modifying SHO parameters like trigtime1B and trigtime1A to still meet OSS KPI targets, and addressing bad spot coverage and pilot pollution first before applying these guidelines.
(3) For new 3G sites with SHO overhead below 60% after applying the guidelines, exemption can be made if target coverage conflicts with the rules. The multi-sector re-azimuth guidelines ensure
(1) The document provides guidelines for optimizing 3G cell sites with high SHO overhead, including cells with SHO overhead greater than 50%, TP greater than ISD by more than 20%, and cells not meeting downtilt checks.
(2) The guidelines include performing RET to optimize maximum mechanical tilt based on height and ISD, modifying SHO parameters like trigtime1B and trigtime1A to still meet OSS KPI targets, and addressing bad spot coverage and pilot pollution first before applying these guidelines.
(3) For new 3G sites with SHO overhead below 60% after applying the guidelines, exemption can be made if target coverage conflicts with the rules. The multi-sector re-azimuth guidelines ensure
1. Cells with SHO OH >50% 2. Cells with TP > START ISD > 20% 3. Check cells DT E tilt < Y Perform RET (1) Maximum mechanical tilt based on height and ISD max coverage Check Y Overshooti N MOD ng cells (3) 1BPS Y INTRARELTHDFOR1BP >8 OR S =8 1APS >4 INTRARELTHDFOR1AP (2) Rule 1,2 and 3 can have exemption for case N S=4 where target coverage is in conflict with the rules. N Antenna Re-azimuth (3) Modifying SHO parameters should make CCSR Y face to >=10 (3) Y PS and CCSR CS still pass the OSS KPI target. Rule1 TRIGTIME1 MOD face with difference with TRIGTIME1B=320 neighbor neighbor B>320 (4) This guideline applies for SHO overhead optimization, bad spot coverage optimization N N (specially due to pilot pollution) will have to be (1)M tilt < Y fixed first or in parallel. Re-azimuth Perform mechanical (5) 3G new sites with site level SHO OH pass Overlap Y max based >=10 down tilt target, but with at least 1 sector having Rule2 opposite ISD/height difference with neighbor neighbor N Target SHO OH < Actual SHO OH <60% Neighbor 43% < 55% < 60% N overshooti Y Perform neighbor ng optimization AND already applied SHO OH guideline above, will Azimuth ~PRACH Y be considered for acceptance. Rule3 between Re-azimuth > >20% antenna 90 difference <=90 Best Effort Optimization * For non-RET(new site), E tilt and M tilt should go together. 3G Multi-Sector Re-Azimuth guideline
More than 10 Rule 1: Opposite Antenna can
not face to face, the minimum angle of them should more than 10 degrees;
Overlap no opposite More than 10 Rule 2: The overlap can not
opposite, the minimum angle of them should more than 10 degrees;
Angle between Antennas larger than 90 Rule 3: The angle between 65
antenna and split antenna should be Less than 90 more than 90 more than 90 degrees between the split antenna should be more than 100 degree