Beruflich Dokumente
Kultur Dokumente
0 New Features
Workshop 2
Spotwelds
Large Deformation Analysis of thin plate assembly
spotwelded together
ANSYS v9.0
Spot weld
Workshop
Goal
Build spotwelded assembly, run and 4.00
post process a large deflection analysis. Displacement
0.50 dia
Model Description Spot weld
15.00 R
14.00 R
12.9 R
Spot weld
0.15 0.10 Typ
October 1, 2004
Inventory #002157
2004 ANSYS, Inc. 9.0 New Features WS2-2
ANSYS v9.0
Spot weld Workshop
Steps to Follow:
Start an ANSYS interactive session and open (or read in) the input file named
spotweld.inp. You might need to set your Files of type: = (*.*)
Use the GUI menu method:
Select the Open ANSYS File ICON
Select the file spotweld.inp
Click OK
October 1, 2004
Inventory #002157
2004 ANSYS, Inc. 9.0 New Features WS2-3
ANSYS v9.0
Spot weld Workshop
Note: One hard point (keypoint #33) has already been created at the location defining the centerline of the
spot weld. This hard point is associated with the top plate (area# 7). The node (#393 in 9.0) associated
with this hard point has been parameterized with the name SW_NODE for convenience.
October 1, 2004
Inventory #002157
2004 ANSYS, Inc. 9.0 New Features WS2-4
ANSYS v9.0
Spot weld
Workshop
With the area entry (2,7), ANSYS will associate node #393
with area #2 and create a second node on area #7 which is
coincident with node 393. Hence, the warning message. October 1, 2004
Inventory #002157
2004 ANSYS, Inc. 9.0 New Features WS2-5
ANSYS v9.0
Spot weld
Workshop
Note: A maximum of
11 surfaces can be
included in one spot
weld assembly
October 1, 2004
Inventory #002157
2004 ANSYS, Inc. 9.0 New Features WS2-7
ANSYS v9.0
Spot weld
Workshop
October 1, 2004
Inventory #002157
2004 ANSYS, Inc. 9.0 New Features WS2-8
ANSYS v9.0
Spot weld
Workshop
October 1, 2004
Inventory #002157
2004 ANSYS, Inc. 9.0 New Features WS2-9
ANSYS v9.0
Spot weld
Workshop
October 1, 2004
Inventory #002157
2004 ANSYS, Inc. 9.0 New Features WS2-10
ANSYS v9.0
Spot weld
Workshop
Additional Features:
The Spot weld assembly can also be created, listed and deleted with the following commands:
SWGEN,sweld1,0.50,7,2,sw_node,, !Generates spot weld between first two surfaces (7 and 2)
SWADD,sweld1,,12 !Adds surface 12
SWLIST !Lists spot weld specifications and reactions (after solution is complete)
SWDEL,sweld1
By default, ANSYS connects each surface together by creating MPC184 rigid link elements between the spot weld nodes. A
flexible weld can be created if the active element is a BEAM188 with a circular cross section prior to weld creation. You must
define the material properties for the BEAM188 and define the geometry of the beam section using section definition tools
(SECTYPE and SECDATA commends) in advance of weld creation. Below is an example APDL script for creating the same
spot weld in this workshop model using flexible BEAM188 elements. After the solution run, corresponding results in the
flexible spot weld are conveniently summarized in the SWLIST and are also available in the traditional ETABLE for
BEAM188.
/PREP7
MP,EX,2,28e6
MP,PRXY,2,0.3
SECTYPE,2,beam,csolid
SECDATA,0.25
ET,2,188
TYPE,2
MAT,2 Stress calculations in spot weld
SECNUM,2 are added when BEAM188 is
SWGEN,sweld1,0.50,7,2,sw_node,, active prior to spot weld creation
SWADD,sweld1,,12
October 1, 2004
Inventory #002157
2004 ANSYS, Inc. 9.0 New Features WS2-11