Beruflich Dokumente
Kultur Dokumente
BÂRLAD Annex 1
BALL VALVE RSD-BB 1.1.NPS3.cls300.1.0.1.0.2.5.1.FB
RSD-BB 1.1.NPS3.cls300.3.0.1.0.2.5.1.FB
DOUBLE BLOCK & BLEED
RSD BB type
TRUNNION MOUNTED,
ANTISTATIC, FIRE SAFE
DESIGN API607, API6FA
APPLICATIONS
Designed and executed for use in pipeline systems, which convey fluids under pressure,
neutral or potentially corrosive.
The products situate into the category of accessories for pressure adjustment and meet the
essential requirements for security insurance of users of pressure equipment covered by
GD 584/2004.
BENEFITS
Construction which guarantees the separation of the two fluid paths on both sides of the valve
- upstream and downstream.
Offered in standard variants both with double bearing of the ball (trunnion):
- Split body; Welded body; Top entry
Antistatic construction-electrical contact between all the metallic elements of the valve, fire
safe design acc. to API 607; API6FA (ISO 10497) – certified.
Anti blow out stem design, sealing replacement can be done with the valve under pressure.
Single, double or triple sealing:
- single sealing metal/metal (SPE single piston effect);
- double sealing: primary sealing metal/metal, secondary sealing metal/PTFE,
-triple sealing (DPE – double piston effect): primary sealing metal/metal, secondary sealing
metal/PTFE or metal/FKM assured by one of the upstream sealing system.
-Dual seat –Double piston efect with maximum realibility
The sealing is permanent and is assured by the springs positioned behind the seats. After the
primary seal is used, the sealing is made by PTFE or FKM gasket and after this one is wear,
the sealing is assured by introduced sealing mastic. The specific structure of stem bearing and
sealing – the two functions of bearing and sealing are separated.
Optionally with lubrication seat for the sliding bearings (stem + ball gaskets) - for gases as the
working fluid.
The valve type "block and bleed" allows to check the gaskets’ tightness degree from de ball
without disassembling it from installation, both in opened or closed position. "Block and Bleed"
type valve, allow verifying the degree of tightness of the seals without dismantling the
installation area both in the open position and closed position.
The standard version allows the pressure verification from the valve’s chamber using a pipe
that has at one end a needle valve and a manometer.
FUNCTIONAL DESCRIPTION
Shut valve – both sides of the ball are Open valve – the valve’s
under the pressure, chamber may become
the valve’s chamber may become depressurized to verify
depressurized the tightness degree
(max.40 bar)
slurry fluid
metalic ringf
Metalic ring
2.Low pressure
Clear fluid
Spring
Stellite ring
3.High presure
slurry fluid
FKM or
PTFE ring
scraper
17-4-PH
2 Fig. 1
3
Fig. 2
a POSITION
1 Above ground
2 Under ground
b VALVE ENDS
1 flanged
2 welded
3 Threads(max DN100)
c NOMINAL DIAMETER
DN or NPS NPS3
d NOMINAL PRESSURE
PN or Class class 300
e BODY/BALL material
1 Carbon steel / stainless steel
2 Carbon steel//alloy steel +Cr or ENP
3 Stainless steel/stainless steel
f SEALING TYPE
0 metal/PTFE
1 metal/FKM
2 metal/PTFE +metal/metal
3 metal/FKM +metal /metal
4 Dual seat
g TEMPERATURE
1 -30 +110C
2 0 +200C
h LUBRICATION OPTION
0 Without lubrication access
i DIMENSION
1 SR-EN 558-1
2 API 6D
j ACTUATORS
1 Gear or
2 Electric actuators
3 Gas over oil actuators
4 Electrohydraulic actuators
5 Pneumatic actuators
k VALVE TYPE
1 Split body
2 Top entry
3 Full welded
l BORE
FB Full bore
RB Reduced bore