Beruflich Dokumente
Kultur Dokumente
Ajmal Shafi
Release with Redirect to LTE Based on Coverage Check (FAJ 121 3960)
RIM Support for System Information Transfer to LTE (FAJ 121 2179)
GSM
Provides the Feature SI is sent in
mechanism enables LTE S12quarter on
to distribute capable BCCH &
SI for cell devices to measurement
reselection to detect LTE information
LTE. access . on SACCH.
LTE Possible to
frequencies set priorities
need to be between
define. different
technologies.
This feature provides inter Based on Operator assigned priority levels set for
system mobility between
Utran & LTE. each LTE frequency layer as well as for the Utran
serving cell.
Device controlled & guided
by Parameters which is sent
to UE through SIB
messages.
Value 0 means lowest & 7 means highest priority.
Parameters for cell
reselection between WCDMA
to LTE is sent on SIB19.
If UE detects a neighboring LTE cell with higher
Cell reselection is supported priority than the serving Utran cell it will attempt a
by Eutra Capable UE’s both cell reselection.
Idle & URA PCH Mode.
Cell selection/reselection
process runs when :
When the UE is
switched ON.
When the cell on which
it is camping is no
longer suitable .
When UE has found a
better neighboring cell
than the currrent one.
When the UE is in
limited service state on
an acceptable cell.
Feature is divided
in to three parts, Dedicated Dedicated Priorities
each part can be Priorities based on based
Dedicated Priorities in
Shared Network, with
Subscriber on IRAT Offload
independently Profile ID. from LTE.
Shared RAN (MOCN).
enabled or
disabled:
Affected Parameters
Parameter Description
Time during which a specific UE that was offloaded from E-UTRAN is not
redirected back. Only used when the feature IRAT Offload From LTE is activated.
Handover::blockRwrEutraTime If the LTE Cell Reselection Dedicated Priorities is activated
and RncFunction::offloadDedicPrioEutraEnabled is set to TRUE,
theRncFunction::offloadDedicPrioEutraTime value is used instead.
Parameter Description
UTRAN cell configuration used for absolute-priority-based cell reselection to E-
UTRAN. The priorities used in DedicatedPriorites are always lower than the
UtranCell::absPrioCellRes value of cellReselectionPriority in this structure. Lowering the value
reduces the number of E-UTRA frequencies sent to
the UE in DedicatedPriorities IE
UTRAN cell configuration used to build the UTRA frequency list
UtranCell::uarfcnDl
for DedicatedPriorities IE in RRC Utran Mobility Information message.
WCDMA carrier configuration used to build the UTRA frequency list
WcdmaCarrier::uarfcnDl
for DedicatedPriorities IE in RRC Utran Mobility Information message.
Counter Description
Test cases
Such relationship is
called RIM
association.
Once a RIM
association is
established, enodeB
receives update
from the RNC when
SI for the Utran cell
in that RIM
association changes.
Field test have shown that 1.2 s reduction in call setup time for CS fall back from LTE
has been achieved.
Interruption time of PS service is shortened when moving from LTE to WCDMA due to reduced call
setup time.
Interworking between WCDMA & LTE | Ajmal Shafi | 2016-06-16 | Page 30
RIM Parameters & Counters
Default
Parameter Description Value Unit
Counter Description
Number of system information update events for this cell that may trigger
UtranCell::pmRimUtraSiUpdates reporting towards eNB associations over RIM during a ROP
Handover
Network Requirement
License, CXC 403 0107, is ready for the feature PSHO from LTE.
Multi RAT capable (UTRAN and E-UTRA) UE with at least release 8 version.
Interworking between WCDMA & LTE | Ajmal Shafi | 2016-06-16 | Page 34
Before PSHO After PSHO
Benefits
Short
PS Multi-RAB
NO PS data connection interruption time The UE moved
connection is
drop during bad LTE due to reserved from LTE to
supported in
coverage. resources in Utran.
PSHO.
Utrancell before
UE releases its resources from WCDMA & to LTE by sending RRC connection release message
searches LTE. As soon as it finds LTE cell it reestablishes with redirection information.
Connection
Interworking on WCDMA
between LTE by&performing TA Update.
LTE | Ajmal Shafi | 2016-06-16 | Page 38
LTE features
Counters
Counter Description
pmCriticalBorderEvalReport The total number of A2 measurement reports received due to critical threshold is
reached. This counter is used instead of pmBadCovEvalReport when the feature
Mobility Control at Poor Coverage is activated.
pmBadCovSearchEvalReport The total number of A2 measurement reports received due to entering the Search
zone. This counter is used when the feature Mobility Control at Poor Coverage is
activated.
Parameter Description
a1a2SearchThresholdRsrp The RSRP threshold for the Event A1 and Event A2 RSRP Search measurements.
a1a2SearchThresholdRsrq The RSRQ threshold for the Event A1 and Event A2 RSRQ Search measurements.
hysteresisA1A2SearchRsrp The RSRP hysterisis used by the Event A1 and Event A2 RSRP Search measurements.
hysteresisA1A2SearchRsrq The RSRQ hysterisis used by the Event A1 and Event A2 RSRQ Search measurements.
The time used to determine whether the measured frequencies shall be excluded for
searchEffortTime mobility action at critical threshold or not.
timeToTriggerA1Search The time-to-trigger value for both the RSRP and RSRQ Event A1 Search measurements.
timeToTriggerA2Search The time-to-trigger value for both the RSRP and RSRQ Event A2"Search measurements.
a2CriticalThresholdRsrp The RSRP threshold for the Event A2 RSRP Critical Coverage measurements.
a2CriticalThresholdRsrq The RSRQ threshold for the Event A2 RSRQ Critical Coverage measurements.
hysteresisA2CriticalRsrp The RSRP hysterisis used by the Event A2 RSRP Critical Coverage measurements.
hysteresisA2CriticalRsrq The RSRQ hysterisis used by the Event A2 RSRQ Critical Coverage measurements.
The time-to-trigger value for both the RSRP and RSRQ Event A2 Critical Coverage
timeToTriggerA2Critical measurements.
Activates or deactivates EUTRAN inter-frequency measurements for mobility purposes
ueMeasurementsActiveIF when Mobility Control at Poor Coverage feature is enabled.
Activates or deactivates UTRAN measurements for mobility purposes when Mobility
ueMeasurementsActiveUTRAN Control at Poor Coverage feature is enabled.
Activates or deactivates GERAN measurements for mobility purposes when Mobility
ueMeasurementsActiveGERAN Control at Poor Coverage feature is enabled.
Activates or deactivates CDMA2000 measurements for mobility purposes when Mobility
ueMeasurementsActiveCDMA2000 Control at Poor Coverage feature is enabled.
Used to activate or deactivate RSRQ measurements. For more information, see Radio
zzzTemporary13 Network.
Used to activate or deactivate the extended A5 "Target Good Enough" check. For more
zzzTemporary14 information
Reduced Enhanced
Helpful in High priority
interruptions control over
offload the services such
in data flow how UE’s are
LTE cells as VOIP in
due to transferred
Benefits: transition between
based on high load
measurement network is
from one different
threshold not
technology to frequencies &
settings. interrupted.
another. cells.
Parameter Description
Indicates whether the coverage area of the cell indicated by the cell relation has approximately
the same coverage area (overlap) as this cell, or whether it fully covers this cell, or if it is fully
coverageIndicator contained in this cell
mobilityAction Preferred way to transfer UE in connected mode to a specific WCDMA frequency
Routing area code of a routing area
The value -1 of the attribute is used to mark that the optional RAC IE should not be sent in the
rac Target ID IE of the HANDOVER REQUIRED S1 message.
Location area code of the external UTRAN cell
A fixed-length code identifying the location area within a PLMN. The value 0 of the attribute is
used to mark invalid or unusable location area code information for the cell. For example,
handover to an external UTRAN cell (that is part of a UTRAN cell relation) can be considered only
if the value of the location area code attribute is not 0.
lac
Counter Description