Beruflich Dokumente
Kultur Dokumente
Objective
2
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Table of Contents
1. Standard Procedure
2. Alternative Scenario’s
3
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Management communication
External Internal
VLAN VLAN 4094
External management
- Mgmt VLAN
IP addresses configurable by operator
4
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Turn up procedure
Log on to the ISAM for the first time via Full CLI
- Connect via RS232 port on NANT-D, DCE RJ45 interface
ASCII coding no parity
9600 bps 1 stop bit
8 bits No flow control
6
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Turn up procedure using an access port: L1/L2 configuration
7
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Basic concepts: Virtual Port
• ISAM supports interfaces on VLANs
• VLAN on IHUB are represented by V-VPLS
• Solution: IP interfaces are associated with v-VPLS via “virtual port”
IES
IP
L3 SAP
L2
9
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Turn up procedure: SNMP
Now you can create & supervise the ISAM on the AMS
10
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Saving the management configuration
• Once turn-up procedure finished you need to manage the ISAM in the AMS (see
chapter on AMS Introduction)
• From the beginning, some basic decisions need to be taken to avoid unnecessary
reboots or other service disruption later during operation:
- Whether you are going to use NT-B and NTIO slot as universal slot instead (see equipment
configuration)
- xfp direction (up or down), if used for expansion (see equipment configuration)
12
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
2 Alternative scenario’s
13
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Alternative 1: LAG – Link Aggregation Group
- All ports in a LAG must share the same characteristics, auto-negotiation must be
switched off.
- Changes can only be made to the primary port configuration, and changes to the
primary port configuration are automatically made to the non-primary ports.
One of the
links is
randomly
selected as
PRIMARY
14
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Alternative 1: using an access port: L1/L2 configuration
• Network
with LAGport configuration + LAG
configure port nt-a:xfp:1 no shutdown
configure port nt-a:xfp:1 ethernet no autonegociate
• LAG configuration
configure lag 10
configure lag 10
port nt-a:xfp:1
no shutdown
15
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Alternative 1: using an access port: L1/L2 configuration with LAG
After these commands, you need to also do the L3 configuration and SNMP
configuration (cfr pag 8 and 9)
16
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Alternative 2: Turn up procedure using a network port (from R4.1
onwards)
• Network port configuration
configure port nt-a:xfp:1 ethernet mode network
configure port nt-a:xfp:1 no shutdown
17
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
7302/5520 Hands-on
18
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Hands-on
19
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
www.alcatel-lucent.com
www.alcatel-lucent.com
20
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.