Beruflich Dokumente
Kultur Dokumente
pumps
• The Centrifugal pump has the following main
components:
Components of centrifugal
pumps
• Impeller
A rotating wheel fitted with a series of backward curved
vanes or blades mounted on a shaft connected to the
shaft of an electric motor. Due to rotation of impeller
centrifugal force is produced on the liquid, which
produces kinetic energy in the liquid. Water enters at the
centre of the impeller and moves radially outward and
then leaves from outer periphery of the impeller with a
very high kinetic energy.
Components of centrifugal
pumps
• Casing
It is an airtight chamber, which accommodates the
rotating impeller. The area of flow of the casing gradually
increases in the direction of flow of water to convert
kinematic energy into pressure energy.
Components of centrifugal
pumps
• Suction pipe
It is the pipe through which water is lifted from the sump
to the pump level. Thus the pipe has its lower end
dipped in the sump water and the upper end is
connected to the eye or the inlet of the pump. At the
lower end, a strainer and a foot-valve are also fitted.
i. Strainer
It is a screen provided at the foot of the suction pipe, it
would not allow entrance of the solid matters into the
suction pipe which otherwise may damage the pump.
Components of centrifugal
pumps
• Suction pipe
ii. Foot valve
It is a one direction valve provided at the foot of the
suction pipe. It permits flow only in one direction i.e.
towards the pump. Foot valve facilitates to hold the
primed water in the suction pipe and casing before
starting the pump. Priming is the process of filling of
water in centrifugal pump from foot valve to delivery
valve including casing before starting the pump.
Components of centrifugal
pumps
• Delivery pipe
Delivery pipe is used for delivery of liquid. One end
connected to the outlet of the pump while the other
delivers the water at the required height to the delivery
tank. It consists of following components:
i. Delivery gauge
This gauge connected on the delivery side of the pump
to measure the pressure on the delivery side.
ii. Delivery Valve
It is a gate valve on the delivery side of the pump to
control the discharge
Components of centrifugal
pumps
• Shaft
It is a rotating rod supported by the bearings. It transmits
mechanical energy from the motor to the impeller.
2. Manometric Efficiency
Manometric efficiency is defined as the hydraulic
efficiency of an ideal pump.
Losses and Efficiencies
3. Volumetric Efficiency
The pressure at the outlet of the impeller is higher than
at the inlet. Thus there is always a tendency on the part
of water to slip back or leak back through the clearance
between the impeller and the casing. There can also be
some leakage from the seals. These are called
volumetric losses.
Volumetric efficiency is the ratio of the actual discharge
to the total discharge.
Q = Amount of discharge
Let ∆Q = Amount of leakage.
ηv = Q / (Q+ ∆Q)
Its value lies between 0.97 and 0.98.
Losses and Efficiencies
4. Mechanical Efficiency
Mechanical losses in case of a pump are due to
(a) Friction in bearings
(b) Disc friction as the impeller rotates in liquid.
Mechanical efficiency is the ratio of the actual power
input to the impeller and the power given to the shaft.
Let P = Total power input to the shaft
∆ P = Mechanical losses
ηm = (P - ∆ P) / P
Its value lies between 95% - 98%.
Losses and Efficiencies
5. Overall Efficiency
It is the ratio of the total head developed by a pump to
the total power input to the shaft.
ηo = (ρQgH) / P
Range of overall efficiency is between 0.71 to 0.86.
Problem: A centrifugal pumps delivers 50 liters of water per
second to a height of 15m through a 20 m long pipe.
Diameter of the pipe is 14 cm. Overall efficiency is 72 %,
and the coefficient of friction 0.015. Determine the power
needed to drive the pump.
Solution:
Hs = 15m
Q=0.05 m3/s
I = 20 m
f = 0.015
d = 0.14 m
ηo = 72%
We have,
ηo = (ρQgH) / P
H = Hs+ Hf + Vd2/(2g)
Problem:
Solution:
For which Vd is given by,
Q = π/4 d2 Vd
0.05=π/4(0.14)2 Vd
Vd = 3.25 m/s
And hf = (4flVd2) / (2gd)
hf = (4x0.015x20x3.252)/(2x9.81x0.14)
hf = 4.61 m
H=15+4.61+ 3.252/(2x9.81)= 20.15m
Power to drive pump can be calculated as follows:
ηo = (ρQgH) / P
0.72 = (1000x0.05x9.81x20.15) / P
Or P = 13726 W = 13.726 k W.
Multistage Pumps
To develop a high head, the tangential speed μo has to
be increased. However an increase in the speed also
increases the stresses in the impeller material. This
implies that centrifugal pump with one impeller cannot be
used to raise high heads.
More than one pump is needed to develop a high head.
The discharge of one pump is delivered to the next to
further augment the head.
However, a better way is to mount two or more impellers
on the same shaft and enclose them in the same
cashing. All the impellers are put in series so that the
water coming out of one impeller is directed to the next
impeller and so on (Fig.10.22).
Multistage Pumps