Beruflich Dokumente
Kultur Dokumente
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA
Filters
Electrical/Electronic filters are electronic circuits which perform signal processing functions, specifically to remove unwanted frequency components from the signal, to enhance wanted ones, or both. Audio equalizers and crossover networks are two well-known applications of filter circuits. Equalizers allow the amplitudes of several frequency ranges to be adjusted to suit the listener's taste and acoustic properties of the listening area. Crossover networks block certain ranges of frequencies( low-frequency signals) from reaching tweeter (high-frequency speakers).
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA
Types of Filters
Electronic Filters belong one of the following types: Digital Filters Sampled-data Filters
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA
Low-pass(LP) Filter
A low-pass(LP) filter is a filter that passes lowfrequency signals but attenuates (reduces the amplitude of) signals with frequencies higher than the cutoff frequency. A low-pass(LP) filter is the opposite of a high-pass(HP) filter.
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA
Ideal LP response
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA
Continuous-time LP Filter
An ideal LP filter completely eliminates all frequencies above the cutoff frequency while passing those below unchanged. Ideal LP frequency response is a rectangular function, and is a brick-wall filter. The transition region present in practical filters does not exist in an ideal filter.
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA
The gain-magnitude frequency response of a first-order (one-pole) low-pass filter. The voltage gain is shown in decibels .At cut-off frequency there is a 3 dB decline .Angular frequency is shown in units of radians per second.
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA
Third- and higher-order filters are defined similarly. In general, the final rate of power roll off for a nth order LP filter is 20n dB per decade.
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA
The combination of resistance and capacitance gives you the time constant of the filter = RC (represented by the Greek letter tau)
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA
This 1st-Order low pass Butterworth type filter, consists simply of a passive RC filter connected to the input of a non-inverting operational amplifier. The frequency response of the circuit will be the same as that of the passive RC filter, except that the amplitude of the output signal is increased by the pass band voltage gain of the amplifier. The gain in the pass band is R2/R1
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA
Where AF = the pass band gain of the filter, (1 + R2/R1) = the Frequency of the Input Signal in Hertz, (Hz) c = the Cut-off Frequency in Hertz, (Hz)
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA
High-pass Filter
A high-pass(HP) filter offers easy passage to high-frequency signal and attenuates the lowfrequency signal.
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA
The cutoff frequency for a high-pass filter is that frequency at which the output voltage equals 70.7% of the input voltage. Above the cutoff frequency, the output voltage is greater than 70.7% of the input, and vice versa.
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA
Band-pass(BP) filter
The Band-Pass(BP) filter passes a selected range or band of frequencies that can be either narrow or wide while attenuating all those outside of this range. The Band-Pass(BP) filter can be of two types:
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA
Band-pass(BP) filter
Frequency Response of a 2nd order Band-Pass(BP) Filter The term "bandwidth" refers to the difference between the lower cut-off frequency(cLOWER) and the upper cut-off frequency (cUPPER) points.
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA
Band-pass(BP) filter
a
A band-pass(BP) filter arrangement commonly consists of combination of a Low-pass (LP) and a High-pass(HP) filter.
In BP Filter, the width of the pass-band between the upper and lower-3dB corner points determine the Quality Factor(Q-point) of the circuit. This Q Factor is a measure of how "Selective" or "Un-selective" the band pass filter is towards a given spread of frequencies. The lower the value of the Q factor the wider is the bandwidth of the filter and consequently the higher the Q factor the narrower and more "selective" is the filter.
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA
Band-Reject(BR) Filter
A band-stop filter or band-rejection filter passes most frequencies unaltered, but attenuates those in a specific range to very low levels. It is the opposite of a band-pass filter. A notch filter is a band-stop filter with a very narrow stop band.(high Q factor).Notch filters are used in live sound reproduction(Public Address systems, also known as PA systems) and in instrument amplifier(especially amplifiers or preamplifiers for acoustic instruments such as acoustic guitar, mandolin etc.) to reduce the noise and unwanted frequencies. e.g., Anti-hum filter is used to filter out the mains hum from a 50 Hz power line, though its higher harmonics could still be present. The filter passes all frequencies, except for the range of 4951 Hz.
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA
All-pass Filter
The all-pass filter is an important building block in audio signal processing systems. It is called all-pass because all frequencies are passed equally. In other words, the amplitude response of an all-pass filter is any nonzero constant at each frequency, but filter changes the phase relationship between various frequencies. Generally, the first-order all-pass filter is described by the frequency at which the phase shift crosses 90
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA
For 1st order all-pass filter ,the amplitude response is flat (within the bandwidth limitation of the amplifier), and there is a 90 degree phase shift at the "corner" frequency.
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA
for matching phase in systems where phase is important for producing delays in circuits that need to delay a signal for creating 90o shifts for quadrature modulators
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA
END
Department of Electronics and Communication Engineering, Manipal Institute of Technology, Manipal, INDIA