Beruflich Dokumente
Kultur Dokumente
Montage
WARNUNG
Installation
WARNING
Safe operation is dependent upon proper handling and installation by qualified personnel under observance of all warnings contained in this instruction manual.
Sicherer Betrieb des Schalters setzt voraus, dass er von qualifiziertem Personal sachgem unter Beachtung der Warnhinweise dieser Bedienungsanleitung montiert und in Betrieb gesetzt wird. Insbesondere sind sowohl die allgemeinen Errichtungs- und Sicherheitsvorschriften zu Arbeiten an Starkstromanlagen (z.B. DIN VDE) als auch die den fachgerechten Einsatz von Hebeeinrichtungen und Werkzeugen und die Benutzung persnlicher Schutzausstattungen (Schutzbrillen u..) betreffenden Vorschriften zu beachten. Bei Nichtbeachtung knnen Tod, schwere Krperverletzung oder erheblicher Sachschaden die Folge sein.
In particular the general erection and safety regulations (e.g. DIN VDE, IEC) and regulations regarding the correct use of hoisting gear and tools and of personal protective gear (safety goggles and the like) shall be observed.
Non-observance can result in death, severe personal injury or substantial property damage.
GEFAHR
Schweres Gert. Falsches Kranen kann Tod, schwere Personenschden sowie Schden an Gerten und Ausrstung bewirken. Niemals einen Leistungsschalter, Sicherungseinschub oder Einschubrahmen ber Personen heben. Bedienungshinweise zum Kranen beachten. Nur OSHA/NIOSH geprftes Krangeschirr verwenden. Benutze personelle Schutzausrstung zum Heben oder Bewegen von Leistungsschaltern und Einschubrahmen.
DANGER
Heavy Equipment. Improper lifting will cause death, serious personal injury, or equipment/property damage. Never lift a circuit breaker, fuse carriage, or guide frame above personnel. Follow instructions for use of lifting bar assembly. Use OSHA/NIOSH approved rigging equipment and personal protection equipment for lifting/moving the circuit breakers and guide frames.
5.1
5.1.1
Einbau
Einbaulage
30
5.1
5.1.1
30
30
Mounting
Mounting position
30
h max 1 mm
51
5.1.2
5.1.2
Werden in Schaltschrnken ohne Fachbden mehrere Einschubschalter bereinander angeordnet, empfehlen wir Lichtbogenkammerabdekkungen zu verwenden.
If several draw-out circuit-breakers are arranged one above the other in cubicles without compartment bases we recommend to use arc chute covers.
5.1.3
5.1.3
Setzmutter Non-removable nut 4 Schrauben M8-8.8 + Spannscheiben 4 bolts M8-8.8 + strain washers
52
Darstellung fr Baugre II mit Frontanschluss Representation for frame size II with front connection
53
5.2
Anschluss-Schienen
q Baugren / Mabilder (Seite 7-1)
5.2
Connecting bars
q Frame sizes / dimension drawings (page 7-1)
5.2.1
Horizontalanschluss
5.2.1
Horizontal connection
The horizontal connection is the standard connection for fixedmounted circuit-breakers and guide frames.
13.5 mm
For guide frames only: q Installing horizontal connection for retrofitting (page 5-9)
5.2.2
5.2.2
M 12
70 4 Nm
Der Einbau der Flanschanschlsse erfolgt wie der Einbau der Vertikal- und Horizontalanschlsse q (Seite 5-9).
The flanged connections are installed in the same way as the vertical and horizontal connections q (page 5-9).
54
5.2.3
Frontanschluss Festeinbauschalter
5.2.3
(1)
(2)
(3)
Standard version Version according to DIN 43673 (double hole row) Holes 13.5
(3)
(4) 85 Nm (5)
85 Nm
(6) Gr. / Size 5 (7) (8) 8 Nm (1) Fr Baugre: I II (2) Fr Baugre: I 1600 A II 2500 A, 3200 A III 4000 A Lange Anschluss-Schiene Kurze Innensechskantschraube ISO 4762 M6 mit Spannscheibe Kurze Distanzhlse Schlossschraube DIN 603 M12 mit Spannscheibe und Mutter Lange Distanzhlse Lange Innensechskantschraube ISO 4762 M6 mit Spannscheibe Kurze Anschluss-Schiene (9) (1) For frame size: I II (2) For frame size: I 1600 A II 2500 A, 3200 A III 4000 A Long connecting bar Short hexagon socket screw ISO 4762 M6 with strain washer Short distance sleeve Coach screw DIN 603 M12 with strain washer and nut Long distance sleeve Long hexagon socket screw ISO 4762 M6 with strain washer Short connecting bar 8 Nm Gr. / Size 5
Hinweis
Diese Anschlussart ist in der BG III C-Klasse nicht zulssig.
NOTE
This type of connection is not permitted in FS III C-class.
55
Einschubrahmen
Ausfhrung der Anschluss-Schienen:
Guide frame
Two variations are offered:
Standardausfhrung Ausfhrung nach DIN 43673 (Doppellochreihe) Nuten fr Phasentrennwnde; Einbaulage wie gezeigt! Sttzer Bohrungen 13,5
Standard version Version according to DIN 43673 (double hole row) Slots for phase separation walls; mounting position as shown! Support Holes 13.5
(3)
(4) 85 Nm
85 Nm
(5)
Gr. / Size 5
Gr. / Size 5
10 Nm
10 Nm
(1)
Fr Baugre: I II
(1)
(2)
Fr Baugre: I 1600 A II 2500 A, 3200 A III 4000 A Innensechskantschraube ISO 4762 M6 mit Spannscheibe Sttzer; Einbaulage wie gezeigt! Schlossschraube DIN 603 M12 mit Spannscheibe und Mutter
(2)
For frame size: I 1600 A II 2500 A, 3200 A III 4000 A Hexagon socket screw ISO 4762 M6 with strain washer Support; mounting position as shown! Coach screw DIN 603 M12 with strain washer and nut
Umrsten von Vertikal- oder Flanschanschluss auf Frontanschluss erfordert vorher Einbau des Horizontalanschlusses! q (Seite 5-8)
Conversion from vertical or flange connection to front connection requires installation of horizontal connection first! q (page 5-8)
56
5.2.4
Vertikalanschluss
5.2.4
Vertical connection
Festeinbauschalter
Fixed-mounted breaker
Bemessungsnennstrom Rated current 1000 A 1600 A 1) 1 x M12-8.8 + Mutter + Spannscheiben (oben + unten) 1 x M12-8.8 + nut + strain washers (top + bottom) 85 Nm
1)
2 Anschluss-Schienen pro Hauptanschluss, oben und unten mittels Langloch versetzt befestigt, s. Bild fr Baugre II. 2 x 13.5 mm 2 connecting bars per main terminal, fixed . upper and lower terminal by means of elongated at hole with offset, see drawing for size II.
1)
3 x M12-8.8 + Muttern + Spannscheiben (oben + unten) 3 x M12-8.8 + nuts + strain washers (top + bottom) 85 Nm
1)
1 Anschluss-Schiene pro Hauptanschluss, mittig befestigt, s. Bild fr Baugre I. 1 connecting bar per main terminal, fixed in the centre, see drawing for size I. 3 x 13.5 mm
1)
4 x M12-8.8 + Muttern + Spannscheiben (oben + unten) 4 x M12-8.8 + nuts + strain washers (top + bottom) 85 Nm
4 x 13.5 mm
57
Einschubrahmen
Guide frame
2xM6 2 x 13,5
2xM6
3 x 13,5
4 x 13,5
Vertikalanschlsse links und rechts asymmetrisch Vertical terminals left and right asymmetrical
58
Einschubrahmen
Guide frame
2 1
Gr. / Size 5 Kombischraube M6x20 Hexagon socket bolt M6x20 and strain washer assembly
2 4 1 3
8 Nm
Hinweis
Die Lamellenblcke fr Leistungsschalter der Baugre III, 4000 A, sind nicht vollstndig mit Lamellen bestckt. Achtung! Bei der Montage nur gleichartig ausgestattete Lamellenblcke verwenden.
NOTE
The laminated contacts for circuit breaker frame size III, 4000 A, are not fully equiped with contacts. Attention! Use only similarly equipped laminated contacts.
59
5.2.5
Bestellnummern
5.2.5
Order numbers
Anzahl 1) Number 1) 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Bestellnummer Order number 3WL9111-0AL01-0AA0 3WL9111-0AL02-0AA0 3WL9111-0AL03-0AA0 3WL9111-0AL04-0AA0 3WL9111-0AL05-0AA0 3WL9111-0AL06-0AA0 3WL9111-0AL07-0AA0 3WL9111-0AL08-0AA0 3WL9111-0AL11-0AA0 3WL9111-0AL12-0AA0 3WL9111-0AL13-0AA0 3WL9111-0AL14-0AA0 3WL9111-0AL51-0AA0 3WL9111-0AL52-0AA0 3WL9111-0AL53-0AA0 3WL9111-0AL54-0AA0 3WL9111-0AL55-0AA0 3WL9111-0AL56-0AA0 3WL9111-0AL57-0AA0 3WL9111-0AL58-0AA0 3WL9111-0AL61-0AA0 3WL9111-0AL62-0AA0 3WL9111-0AL63-0AA0 3WL9111-0AL64-0AA0 3WL9111-0AM01-0AA0
1000A
I 1250A -1600A Frontanschluss einfach oben Front connection, single hole, top
2000A
II 2500A 3200A III I 1250A - 1600A
4000A 1000A
2000A
II 2500A 3200A III I 1250A - 1600A 4000A
1000A
2000A
II 2500A 3200A III I 1250A - 1600A
4000A 1000A
2000A
II 2500A 3200A III I 1600A 4000A
1000A
2 1 3WL9111-0AM02-0AA0 2 1 3WL9111-0AM03-0AA0
2500A
II 3200A III 5000A
1) Number of connecting bars per main contact (e. g. circuit-breaker with 3 poles = 6 main contacts)
5 10
Bestellnummer Order number 3WL9111-0AN01-0AA0 3WL9111-0AN02-0AA0 3WL9111-0AN03-0AA0 3WL9111-0AN04-0AA0 3WL9111-0AN05-0AA0 3WL9111-0AN06-0AA0 3WL9111-0AN07-0AA0 3WL9111-0AN08-0AA0 3WL9111-0AN11-0AA0 3WL9111-0AN12-0AA0 3WL9111-0AN13-0AA0 3WL9111-0AN14-0AA0 3WL9111-0AN15-0AA0 3WL9111-0AN16-0AA0 3WL9111-0AN17-0AA0 3WL9111-0AN18-0AA0 3WL9111-0AN21-0AA0 3WL9111-0AN22-0AA0 3WL9111-0AN23-0AA0 3WL9111-0AN24-0AA0 3WL9111-0AN25-0AA0 3WL9111-0AN26-0AA0 3WL9111-0AN27-0AA0 3WL9111-0AN28-0AA0 3WL9111-0AN31-0AA0 3WL9111-0AN32-0AA0 3WL9111-0AN33-0AA0 3WL9111-0AN34-0AA0 3WL9111-0AN35-0AA0 3WL9111-0AN36-0AA0 3WL9111-0AN37-0AA0
1000A
I 1250A - 1600A Frontanschluss einfach Front connection, single hole
2000A
II 2500A 3200A III I 1250A - 1600A
4000A 1000A
2000A
II 2500A 3200A III I 1250 - 1600A 2000A 4000A
1000A
II
III 6300A
1000A
I 1250 - 1600A Flanschanschluss Flange connection
2000A
II
2500A 3200A
III I
4000A 1000A
1250 - 1600A
2000A
II
2500A 3200A
III
5000A
1) Number of connecting bars per main connection (e.g. 3-pole circuit-breaker, 6 main connections)
5 11
5.3
Hauptleiter anschlieen
5.3
ACHTUNG
Bei 4poligen Leistungsschaltern ist der N-Leiter immer ganz links anzuschlieen. Anderenfalls kann es zu Fehlfunktionen des elektronischen berstromauslsers kommen. Das Anschliessen von Kabeln unmittelbar an die Leistungsschalteranschlsse ist nicht zulssig.
NOTICE
On 4-pole circuit-breakers, the neutral conductor must always be connected all on the left. Otherwise this can cause malfunctions of the electronic overcurrent release. The connection of cables immediatly at the circuit-breaker terminals is not permitted.
Hauptleiteranschluss subern
Schalter Breaker
Kupfer-Anlagenschienen subern
5 12
Hauptleiter absttzen
100
100
5 13
5.4
Hilfsleiteranschlsse
Klemmenbelegung: q Schaltplne (Seite 8-1)
5.4
Auxiliary conductors
Terminal assignment: q Circuit diagrams (page 8-1)
Querschnitte
Cross sections
1x
2x
0,5-2,5 mm2 AWG 20-14 + Aderendhlse 2) Wire end ferrule 2) AWG 14 Lnge/length: 1 m / 40
Empfehlung: AMP, Reihe PIDG AWG 16-14 Bestell-Nr. 50881 Recommendation: AMP, PIDG series AWG 16-14 order no. 50881
1) 1 x bis 2,5 mm2 Rohrform ohne Kunststoffhlse nach DIN 46 228 T1 1 x bis 1,5 mm2 Rohrform mit Kunststoffhlse nach DIN 46 228 T2 2 x bis 1,5 mm2 Rohrform mit Kunststoffhlse, Zwillings-Aderendhlse 2) 2 x bis 2,5 mm2 Rohrform ohne Kunststoffhlse nach DIN 46 228 T1 2 x bis 1,5 mm2 Rohrform mit Kunststoffhlse nach DIN 46 228 T2
1) 1 no. up to 2.5 tube-type without insulating sleeve as per DIN 46 228 T1 1 no. up to 1.5 tube-type with insulating sleeve as per DIN 46 228 T2 2 nos. up to 1.5 tube-type with insulating sleeve, twin wire end ferrule 2) 2 nos. up to 2.5 tube-type without insulating sleeve as per DIN 46 228 T1 2 nos. up to 1.5 tube-type with insulating sleeve as per DIN DIN 46 228 T2
5 14
5.4.1
Messerleiste Anordnung
5.4.1
Receptacle Arrangement
(1)
(2)
X8
X7 COM15
X6
X5
(1) (2)
Lichtbogenkammer Messerleiste
(1) (2)
Nachrsten
Retrofitting
(1)
(2)
0173-06
(1) (2)
Blindblock Messerleiste
(1) (2)
(3)
0173-09
PH 1
0,7 Nm
(3)
(3)
5 15
Leitungen anschlieen
Schraublose Anschlusstechnik
Connecting wires
Screwless terminal system
3,0 x 0,6
5.4.2
Schleifkontaktmodul Nachrsten
5.4.2
(1)
(2)
1
(1) (2) Einschubrahmen mit Schleifkontaktmodulen Schleifkontaktmodul (1) (2) Cradle with sliding contact modules Sliding contact module
For the SIGUT terminal system, a one-piece sliding contact module is also available.
3,0 x 0,6
0769
Einteilige Schleifkontaktmodule bentigen keinen Hilfsstromstecker. Die Leitungen werden direkt am Schleifkontaktmodul angeschlossen.
The one-piece sliding contact modules do not require auxiliary plugs. The wiring is directly to the sliding contact module.
5 16
5.4.3
Hilfsstromstecker Ausfhrungen
(1)
5.4.3
PH 1 0,5 Nm
SIGUT system Ring lug system Insulated ring lug Screws ANSI B 18.6.3 #4
Lnge 1 m Lenght 40
PH 0
(5) (6)
(5) (6)
Screwless terminal system, 2 terminals in parallel per contact Fixed-mounted breaker only: pre-assembled wires
(1)
(2) (1) (2) Rckseite Hilfsstromstecker Fhrungszungen (1) (2) Back side of auxiliary connector Guide tongues
5 17
2
(1)
X5
X6.
(2)
X5
X6.
click
X5
X6.
(3)
(4)
0100-01_nu
Nut Fhrung Modulbezeichnung (hier: X5; muss nach vorn zeigen) Modul X5
Male pin: groove Female socket: guide Number of module (here: X5; has to be oriented to the front) Module X5
Hilfsstromstecker aufsetzen
L
(1)
1 2
(2)
(1) (2)
(1) (2)
Auxiliary connector Fixed-mounted breaker: Breaker secondary disconnect block Draw-out breaker: Guide frame secondary disconnect block
5 18
5.4.4
Leitungsverlegung am Einschubrahmen
5.4.4
WARNUNG
Unzulssige Bereich fr Leitungen: Leitungen knnen beschdigt werden.
WARNING
Impermissable area for wires: Damage to wires in this area.
(1)
(2)
(3)
(4)
*) Sind Lichtbogenkammerabdeckungen vorhanden, drfen die Hilfsleiter nicht auf diesen Abdeckungen verlegt werden.
*) If there are arc chute covers installed, auxiliary wires must not lay directly on top of these covers.
5.4.5
5.4.5
Klemmen X6 immer vorhanden. In Abhngigkeit von der Ausrstung des Leistungsschalters mit optionalem Zubehr sind weitere Klemmen erforderlich. Ggf. mssen die entsprechenden Messerleisten, Hilfsstromstecker und fr Einschubrahmen auch Schleifkontaktmodule nachgerstet werden.
The terminals X6 are standard. Depending on optional accessories, additional terminals may be necessary. In case of necessity, additional receptacles, hand plugs and (for guide frames) sliding contact modules have to be fitted.
5 19
Klemme
Optionales Zubehr
X5
- Motorantrieb mit Speicher mit mechanischem und elektrischem Abruf - 2. Hilfsauslser (Spannungsauslser F2, Unterspannungsauslser F3, verzgerbarer Unterspannungsauslser F4) - Hilfsstromschalter S3 + S4 oder S7 + S8 oder S3 + S8 - Motorabstellschalter S12 (nur mglich, wenn Motrantrieb gewhlt) Ausgelst-Meldeschalter S24 Speicherzustandsmeldung S21 Elektrisch EIN-Taster S10 Meldeschalter am 1. Hilfsauslser S22 Meldeschalter am 2. Hilfsauslser S23
- Charging motor with mechanical and electrical closing command - 2nd auxiliary release (shunt trip F2, undervoltage release F3, delayed undervoltage release F4 - Auxiliary switches S3 + S4 or S7 + S8 or S3 + S8 - Motor disconnect switch S12 (only if charging motor exist) Trip signalling switch S24 Signalling switches storage spring charged S21 Electrical ON push-button S10 Signalling switches 1st auxiliary release S22 Signalling switches 2nd auxiliary release S23
X7
X8
- berstromauslser ETU 45B. ETU55B, ETU76B (interner c) - Anschlsse fr externer Stromwandler fr berlastungsschutz im N-Leiter und Erdschlussschutz - Stromwandler im N-Leiter eingebaut - Stromwandler im Sternpunkt des Transformators eingebaut - Fernrcksetzmagnet F7 - externer Spannungswandler
- Overcurrent release ETU 45B. ETU55B, ETU76B (internal c) - Teminals for external current transformer for overload protection of neutral pole and earth-fault protection - Current transformer installed in the neutral conductor - Current transformer installed in the star point of the transformer - Remote reset coil for trip indication - External voltage transformer
5.4.6
Bestell-Nummern
5.4.6
Order numbers
Bestellnummern / Order numbers Messerleiste Receptacle Zusatzmesserleiste (fr 1000 V-Ausfhrung) Receptacle extension (for 1000 V version) Hilfsstromstecker SIGUT Hand plug SIGUT Hilfsstromstecker schraublose Anschlusstechnik Hand plug screwless terminal system Hilfsstromstecker Ringsen Hand plug ring lug system Hilfsstromstecker mit vormontierten Leitungen Hand plug pre-assembled wires Kodiersatz Coding set Schleifkontaktmodul Secondary disconnects Blindblock Blanking cover Messerleiste SIGUT einteilig Receptacle SIGUT one-piece 3WL9111-0AB01-0AA0
3WL9111-0AB02-0AA0
3WL9111-0AB03-0AA0
3WL9111-0AB04-0AA0
3WL9111-0AB05-0AA0
3WL9111-0AB06-0AA0
3WL9111-0AB07-0AA0
3WL9111-0AB08-0AA0
3WL9111-0AB12-0AA0
3WL9111-0AB18-0AA0
5 20
5.5
Schutzleiter anschlieen
Festeinbauschalter
5.5
14 mm
Einschubrahmen
Guide frame
14 mm
5 21
5.6
5.6
Guide frame Contact module for the guide frame Back of the draw-out circuit-breaker Contact module for the draw-out circuit-breaker
Nachrsten
Anbau des Kontaktmoduls am Einschubrahmen Vor Einbau des Einschubrahmens in die Schaltanlage anbauen.
Retrofitting
Fitting contact module on the guide frame Mount it before fitting the guide frame in the panel.
1
Gr. / Size 5
81Nm
2x cheese-head screw M6x12 DIN 6912 Back of the guide frame Contact module Grounding connection
5 22
Gr. / Size 5
81Nm
Bestell-Nr. Order no. Kontaktmodul fr Einschubrahmen mit 30% der Ausschaltleistung Baugroe I und II Contact module for guide frame for 30% of make-break capacity frame size I and II Kontaktmodul fr Einschubrahmen mit 30% der Ausschaltleistung Baugre III Contact module for guide frame for 30% of make-break capacity frame size III Kontaktmodul fr Einschubschalter BGI / 3polig Contact module for draw-out circuit-breaker frame size I / 3-pole Kontaktmodul fr Einschubschalter BGII / 3polig Contact module for draw-out circuit-breaker frame size II / 3-pole Kontaktmodul fr Einschubschalter BGIII / 3polig Contact module for draw-out circuit-breaker frame size III / 3-pole Kontaktmodul fr Einschubschalter BGI / 4polig Contact module for draw-out circuit-breaker frame size I / 4-pole Kontaktmodul fr Einschubschalter BGII / 4polig Contact module for draw-out circuit-breaker frame size II / 4-pole Kontaktmodul fr Einschubschalter BGIII / 4polig Contact module for draw-out circuit-breaker frame size III / 4-pole 3WL9111-0BA01-0AA0
3WL9111-0BA02-0AA0
3WL9111-0BA05-0AA0
3WL9111-0BA06-0AA0
3WL9111-0BA07-0AA0
3WL9111-0BA08-0AA0
3WL9111-0BA04-0AA0
3WL9111-0BA10-0AA0
5 23
5.7
5.7
5.7.1
Umrsten
Schalterfe wechseln
5.7.1
Conversion
Replacing circuit-breaker feet
2
Gr. / Size 4
Gr. / Size 4
10 Nm
1
1 2 3 4 3 Senkschrauben M6x20 lsen und entfernen Baugrsse I ohne die mittlere Schraube. Schalterfu abnehmen Schalterfu fr Einschubschalter ansetzen Schalterfu mit 3 Senkschrauben M6x20 anschrauben Einfahrantrieb einbauen 1 2 3 4
4
Loosen and remove screws Frame size I without the screw in the middle Remove circuit-breaker foot of fixed-mounted breaker Replace by foot for draw-out breaker Fit it finaly using 3x M6x20 screws Installing racking mechanism
Gr. / Size 5
*) Nm
1
1 2 Einfahrantrieb einsetzen Bei vorhandener Gewindebuchse Einfahrantrieb mit Zylinderschraube M6x12, Spannscheibe und Scheibe 6x18x3 anschrauben. Ist keine Gewindebuchse vorhanden, selbstschneidende Schraube einfetten und einschrauben. *) Anzugsmoment: Zylinderschraube 6 Nm selbstschneidende Schraube 5 Nm 1 2
Install racking mechanism If the insert nut is available, the racking mechanism has to be fixed using a socket head cap screw M6x12, strain washer and washer 6x18x3. If the inserted nut is not available, then grease and tighten the self tapping scew. *) Torque: cheese head screw 6 Nm self tapping screw 5 Nm
5 24
Einfahrwelle einbauen
2 1
1 2 3 Einfahrwelle einsetzen Kurbel aufsetzen Kurbel mit Sicherungsring DIN 471-17x1 sichern Bedienpult ausbrechen 1 2 3 Insert racking shaft Fit crank Secure crank with retaining ring Providing cut-outs in the front panel
1 2
Felder im Bedienpult ausbrechen; geeignete Unterlage verwenden Kanten entgraten Klebeschild am Bedienpult anbringen
1 2
Knock out the fields in the front panel using suitable support Deburr the edges Fix adhesive label at the front panel
Anschlieend Steuerschieber einbauen q (Seite 15-3) berstromauslser einbauen q (Seite 9-82) Bedienpult anbauen q (Seite 24-19) Einschubrahmen mit den fr die jeweilige Anschlussart erforderlichen Anschlussschienen ausrsten (mssen separat bestellt werden) q (Seite 5-4)
Then: Install control gate q (page 15-3) Install overcurrent release q (page 9-82) Install front panel q (page 24-19) Assemble the required terminals on the guide frame (must be ordered separately) q (page 5-4)
5 25
- Einschubrahmen einbauen q (Seite 5-1) - Schalter in Einschubrahmen einsetzen und in Betriebsstelung verfahren q (Seite 6-1)
- Install guide frame q (page 5-1) - Insert circuit-breaker in guide frame and rack into connected position q (page 6-1)
5.7.2
Schilder aktualisieren
5.7.2
Hinweis
Nach dem Einbau zustzlicher Komponenten folgende Angaben mit einem weien, wisch- und wasserfesten Stift ergnzen!
Note
After installing additional components, add the following data using a white and indelible ink pen!
Bestell-Nr. Order no. Umbausatz fr Festeinbau- in Einschubschalter Bg I-3polig Conversion kit for fixed-mounted into draw-out circuit-breaker, frame size I, 3-pole Umbausatz fr Festeinbau- in Einschubschalter Bg II-3polig Conversion kit for fixed-mounted into draw-out circuit-breaker, frame size II, 3-pole Umbausatz fr Festeinbau- in Einschubschalter Bg III-3polig Conversion kit for fixed-mounted into draw-out circuit-breaker, frame size III, 3-pole Umbausatz fr Festeinbau- in Einschubschalter Bg I-4polig Conversion kit for fixed-mounted into draw-out circuit-breaker, frame size I, 4-pole Umbausatz fr Festeinbau- in Einschubschalter Bg II-4polig Conversion kit for fixed-mounted into draw-out circuit-breaker, frame size II, 4-pole Umbausatz fr Festeinbau- in Einschubschalter Bg III-4polig Conversion kit for fixed-mounted into draw-out circuit-breaker, frame size III, 4-pole
3WL9111-0BC11-0AA0
3WL9111-0BC12-0AA0
3WL9111-0BC13-0AA0
3WL9111-0BC14-0AA0
3WL9111-0BC15-0AA0
3WL9111-0BC16-0AA0
Hinweis
Umbaustze knnen nur ber die oben genannte Bestell-Nr. mit zustzlicher Angabe der Identnummer des Schalters bestellt werden.
NOTICE
Conversion kits may only be ordered using the above mentioned order number and only together with the identity numbers of the circuit-breakers the kits are intended for.
5 26