Beruflich Dokumente
Kultur Dokumente
30.06.2005 / MG/JI
Service Bulletin
ZPL II Emulation
Systemvoraussetzung des Druckers:
- AP5.4: 16MB RAM (ist Standard in AP5.4)
- 64xx/ALX/DPM: Speichererweiterung ist ntig: (A4413 fr A2292/A2293 oder A1602 fr A1159)
- Firmware V3.32 oder hher
Bei einem Wechsel des Etikettenmaterials zu einem (gestanzten) Material mit unterschiedlicher Lnge
muss eine manuelle Kalibrierung durchgefhrt werden (siehe unten); Das Senden des neuen
Formats reicht hier nicht aus, da die Materiallnge bei gestanztem Material nicht mit bertragen wird!
Systemparameter => Druckemulation => EasyPlug/ZPL II (es werden EasyPlug und ZPLII
Dateien ausgefhrt). Dies ist nicht erlaubt falls mit der ZPLII Emulation der Text #!A1 oder
#!P1 gedruckt werden soll. Vor dem Download einer neuen Firmware muss dieser Parameter
nicht umgestellt werden.
Mit dem Umschalten wird automatisch ein Reset durchgefhrt. Danach hat man Zugriff auf ein neues
Parametermen:
Hinweis:
- Unmgd interupt: The ^XZ command is normally the last command. In case, some commands
follow, it is possible the printer reacts with Unmgd interupt. Just remove al commands after ^XZ.
This bulletin is confidential to our Distributors and should not be copied in whole or part to any other party without the prior written
consent of Avery Dennison.
Label oben - Label oben Offset (Y-Offset) in dots. Bereich: -120 - +120
Defaultwert = 0; Hinweis: Druckparameter => Y-Druckversatz hat
beim Druck mit ZPLII Emulation keine Funktion.
Position links - Position links Offset (X-Offset) in dots. Bereich: -9999 - +9999
Defaultwert = 0; Hinweis: Druckparameter => X- Druckversatz hat
beim Druck mit ZPLII Emulation keine Funktion.
305DPI Skalier. - Ja/Nein, diese Funktion ermglicht den Drucker einen Druck
mit einem 11,8dot/mm Druckkopf zu emulieren. Soll eine Datei,
welche fr einen ZEBRA Drucker mit 300DPI (11,8dot/mm) erstellt
wurde, mit einem Drucker der 64bit Serie (12dot/mm) gedruckt
werden, dann muss hier auf Ja gestellt werden. Default = Ja
This bulletin is confidential to our Distributors and should not be copied in whole or part to any other party without the prior written
consent of Avery Dennison.
=============================================================================
Recommended Version: Emulation Version 1.13 or higher (lower versions can cause malfunctions).
This version is integrated in Firmware V3.21pre1 or higher
When working with RH versions, the material width needs to be defined very precisely, otherwise
there will be a wrong horizontal print position.
A "Manual Calibrate" (ZPL II Para. menu) must be performed EVERY time the stock is changed to a
material with a different length! Just sending the new format does not help, because the label length is
not transmitted with the format when using punched material!
This bulletin is confidential to our Distributors and should not be copied in whole or part to any other party without the prior written
consent of Avery Dennison.
Note: The ZPL II emulation is NOT supported in Standalone Mode, irrespective of the Printer
Emulation Parameter
b) Darkness - Print contrast for ZPL II jobs. When the contrast is sent via
the ZPL print file this value changes. The print contrast under
Online-> Prog. Esc is not influenced by this parameter.
Values: 0 - 30.
Default is 10 which corresponds to 33%.
f) Label Top - Label Top offset, (Y offset) in dots. Printer Parameter ->Y
Print adjust will be ignored when ZPLII print files are printed.
Values: -120 - +120.
Default is 0.
h) Manual Calibrate - YES, label length calculation for punched material. When
endless material is used the label length is sent in the print
file. This has to be done manually when material is changed.
Shortcut: When printer is in OFFLINE mode press FEED &
PROG ECS together. Calibration should be done after
changing material when there are no jobs loaded in the
printer.
This bulletin is confidential to our Distributors and should not be copied in whole or part to any other party without the prior written
consent of Avery Dennison.
g) Error Checking - YES/NO, This enables or disables error checking when the
printer is handling print fields.
Default is YES.
h) 305 DPI Scaling - YES/NO, this function enables the printer to emulate the
printing of 11.8dots/mm print head.
When print file is made for a Zebra printers with 300 dpi (11.8
dots/mm) and is to be printed on a 64-bit series printer (12
dots/mm) this parameter is to be set to YES.
Default is YES
i) Image Save Path - CF Card/Internal RAM. Selects the memory to be used by the
^IS and ^IL commands: Emulator version 1.10 onwards.
CF Card Optional Compact Flash memory Card
Internal RAM Printers internal RAM (Default)
This bulletin is confidential to our Distributors and should not be copied in whole or part to any other party without the prior written
consent of Avery Dennison.
All other mentioned brand names, product names, or trademarks belong to their respective holders.
This bulletin is confidential to our Distributors and should not be copied in whole or part to any other party without the prior written
consent of Avery Dennison.