UDC 621.882.245.1 December 1986
Slotted round head wood screws
Halbrund-Holzschrauben mit Schlitz Supersedes March 1975 edition,
In keeping with current practice in standards published by the International Organization for Standardization (/SO),
2.comma has been used throughout as the decimal marker.
1 Dimensions Dimensions in mm
Thread size 25 6S
25 55
6 iat | | 502] 5,
[ze / 3a | | 5 | 6B
Nominal size 74 s | I [ 10 12
max - | 438 7 5.38 T t 94 10.45 | 11,55 | 12,65 | 74; 55
min, 7 362 | 462 t 955 | 1045 | 11,45 | 13.45 | 15.45
Nominal size - 35 | 38 | 42 56
m @ | 40a) 446 584
3563! 536
32 “4a 48 64
56 64 | 8a | 96
Nominal size [08 os Ti) 27 16
max _ "| 07 | 08 1 i2) 12— 151) 191
86/086 | 106 | 106 | 1.26) 1.26) 1.66
T 16 [25 [27
t ! 19 | 24
085.
C
Nom Mass (7,88 kg/dm®), in kg per 1000 units, approximately
8725815 T2ET | O40 T
10 9.25 | 10.78 | 0311 | 0.460 0,763 |
cin 123 0358 | 0520 | 0856 | |
vat | 149 TTT
15.1] 169 o4ss | oes2| 104 141 | 199 |
i Lt
21 0532 | 0.763 168 | 224 | "288 “378
251
gta 198 | 262 | 337 | 497 |
4,06 229 301 | 985 | 500
- 260 | 339 | 434 | 555 |
291 | 377 483 | 614
322 | 412 | 531 | 673
1363 | 450 | 580 | 7,32
416 | 526 | 677 | ase
| 972
i
fo pot
Lengths above 80 mm shail be graded in 10 mm steps.
Bracketed sizes shall be avoided if possible.
Wood screws are normally manufactured in sizes for which mass values have been specified. These values are for
guidance only,
Continued on page 2Page 2 DIN 96
2 Technical delivery conditions
Ma Steel
General requirements As specified in DIN 267 Part 1.
Sea thread one _ ‘As specified in DIN 7998.
st =steel Cuzn = copperzine alloy.
Material (grade at the manufacturer's discretion) seni ohey.
(grade at the manufacturer's discretion)
Other materials are subject to agreement.
Limit deviations, Product grade C as specified in SO 4759 Part 11)
geometrical tolerances (previously type g).
| As processed.
Surface finish DIN 267 Part 9 shall apply with regard to electroplating
(a different type of electroplating being subject to agreement)
Acceptance inspection As specified in DIN 267 Part 5.
1) 180 4759 Part 1 applies only for screws with ISO metric screw thread. However, the permissible deviations and
the geometrical tolerances specified in ISO 4759 Part 1 have analogously been adopted for wood screws.
3 Designation
Designation of an M4 slotted round head wood screw of nominal length / = 20 mm, made of steel (St):
Wood screw DIN 96 — 4x 20 St
The DIN 4000 — 2— 1 tabular layout of article characteristics shall apply to screws conforming to this standard.
Note. Until the March 1975 edition of this standard, thread sizes 1,4, 1,7, 2,4 and 2,7 were also included. In that edition,
however, the use of these sizes for new designs was prohibited. In view of existing documentation these sizes may
still be ordered; the dimensional specifications given in that edition shall then apply.
‘Standards referred to
DIN 267 Part1 —_Fasteners; technical delivery conditions; general requirements
DIN,267 PartS Fasteners; technical delivery conditions; acceptance inspection (modified version of ISO 3269,
1984 edition)
DIN 267 Part9 Fasteners; technical delivery conditions; electroplated components
DIN 4000 Part 2 Tabular layouts of article characteristics for bolts, studs and nuts
DIN 7998 Threads and thread ends for wood screws
ISO 4759 Part 1 Fasteners; tolerances; bolts, screws and nuts with thread diameters between 1,6 (inclusive) and
150 mm (inclusive) and product grades A, B and C
Previous editions
DIN 96: 09,19, 08.24, 12.43, 09.53, 03.75,
Amendments
The following amendments have been made in comparison with the March 1975 edition.
a) Nominal lengths 90 mm and 100 mm have been deleted in order to bring this standar
standards on wood screws.
b) Type g has been replaced by product grade C.
¢) The content of the standard has been revised.
into line with the other
International Patent Classification
F 16 B 23/00
F 16 8 25/00