UDC 621,882.245.1,091.6 December 1986
Slotted countersunk (flat) head wood screws
‘Senk-Holzschrauben mit Schlitz ‘Supersedes March 1975 edition.
{In keeping with current practice jn standards published by the International Organization for Standardization (ISO),
2 comma has been used throughout as che decimal marker,
1 Dimensions
Dimensions in mm
Edge radiuses
/ Nat conta
a b2osr
Pos,
—.—»__|
L— i
Threads Wa a Bo
7 mexssoninetae [16 [2 [28 [3 984 4816 [65,6 17 8 [10 |
‘ 12118 | 21 [26 | 302 | 352° 4021 452) 502) 582) ea 742] 842
A si 338 [a7 [$6 [65 [78 a3 792 [02 11 [i258 145 16
a 33.7 410) S08] 990] G95 [795875 "965 | 10787 1185) 1905) 16057 Tass]
2743 | 439 | 879 | 605 | 7.05 785. 875 | 965] 1045/1195 1395.17.45
0961215 | tes} 193} 22 235.25 | 275 3 | 35 5
040s 70s 08 [os [1 1 i242 8 | 2 | 228
fos -o7 “os 11 [1 [sz [42 151] 151] 191] 2a1[ 231 26%
0461 056 066 7086 | 086/108 | 106” i267 1247 166) 206) 206) 266
ve as [08 07 08671 141 [42 719 Tia 16 119] 21 26
iia ‘32040806 [a7 0a a9 7 a ae ia Pe Pe
Nom ‘Mase (7,85 kg/de), in kgper 1000 units, approximately
8738 87S] [one Osi ]
07925} 1075] 0250 0372 060s 0.789 |
ai | 28 |os02 | 0432 0696, 0916 1.18 | |
a rar fa | |
i661 69 0387 0882/0881) 1.17 | 149 185 | 231 |
a) 71 188 See Hee 7
218 72 ‘eaea 0672 [106 [iad | 17922927 a2]
2s 124 | 6 o@22| 130 [173 | 217 271 | 337 | 496
30 [20 “a | 972/154 |204 | 255 310 400) | 580, | :
5 3625 177 238 | 298” 368” 455 ses)
[ "40-3878 ~a1.25 201 268 932 417 516 746 | 134
[4549.76 4525 [290 | 366 465 573,820, | 150
75.7 5125 3291 405) 5.14 632 32) 165
5) 61s a1 4a1 eit 754 108 196
70 | as | 715, | 125 | 227 |
80) 785 815 L ft 143 [as7
‘Lengths above 80 mim shall be graded in 10 mm steps.
Bracketed sizes shall be avoided if posible
Wood serews are normally manufactured in sizes for which mas values have been specified. These values are for
guidance only
Continued on page 2Poge 2. DIN 97
2 Technical delivery conditions
Material ‘Steel Stainless steel
General requirements ‘As specified in DIN 267 Part 1
todtheedond ‘As specified in DIN 7998.
Cuzn = copper-rinc alloy.
St= steel
Material {grade at the manufacturer's ditcration) 17 alse luat any.
{grade at the manufacturer's discretion)
Other meterials ae subject to agreement.
Limit deviations, Product grade C as specified in 1SO 4759 Part 1")
seometrial tolerances (previously type a).
‘As processed.
Surface finish DIN 267 Part 9 shall apply with regard to electroplating
(a different type of electroplating being subject to agreement
‘Acceptance inspection As specified in DIN 267 Part 5.
1) 104759 Part 1 applies only for serews with ISO metric screw thread. However, the permissible deviations and
the geometrical tolerances specified in ISO 4759 Part 1 have a
logously been adopted for wood screws.
3. Designation
Designation of an M4 slotted countersunk (flat) head wood screw of nominal length 1= 20mm, made of ste! (St):
Wood screw DIN 97 — 4x 20 St
“The DIN 4000 ~ 2 ~ 1 tabular layout of article characteristics shall apply to serews conforming to thi standard,
‘Note, Until the March 1975 edition of this standard, thread sizes 1,4, 1,7,2,4 and 2,7 were aso included. In that edition,
however, the use of these sizes for new designs was prohibited. In view of existing documentation these sizes may
stil be ordered; the dimensional specifications given in that edition shall then apply,
‘Standards referred to
DIN 267 Part 1 Fasteners; echnical delivery conditions; general requirements
DIN 267 Part 5 Fasteners; echnical delivery conditions; acceptance inspection (modified version of 1S0 3269,
1984 edition)
DIN 267 Part9 Fasteners; technical delivery conditions; electroplated components
DIN 4000 Part 2 Tabular layouts of article characteristics for bolts, studs and nuts
DIN 7998, Threads and thread ends for wood screws
180 4759 Part 1 Tolerances for fasteners; bolts, screws and nuts with thread diameters between 1,6 mm (inclusive)
and 150 mm (inclusive) and product grades A, B and C
Previous editions
DIN 97: 09,19, 08.24, 12.43, 10.53, 03.75,
‘Amendments
“The following amendments have been made in comparison with the March 1975 edition,
1) Nominal lengths 90 mm and 100 mm have been deleted in order to bring this standard into line
standards on wood serews.
'b) Type g has been replaced by product grade C.
€) The content of the standard has been revised.
the other
International Patent Classification
F 16.6 23/00
F 16 8 25/00