Beruflich Dokumente
Kultur Dokumente
Dne 1000
Dne 1000
DNE-1000
EDITING CONTROL PANEL
BKNE-1010
EDITING FADER PANEL
BKNE-1011
EXTENDED INPUT AND KEYER BOARD
BKNE-1030
VIDEO EFFECTS BOARD
BKNE-1040
3D/LIGHTING/TRAIL EFFECTS BOARD
BKNE-1041
OPERATING PROGRAM
BZNE-1010/1020
! WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
! AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
Manual Structure
1. Installation
DNE-1000 1(E)
1-11. Confirmation and Adjustment of
Secondary Power Supply Voltage ....................................................... 1-29 (E)
1-11-1. DNE-1000 .......................................................................... 1-29 (E)
1-11-2. BKNE-1010 ........................................................................ 1-31 (E)
1-12. Initial Set-up of System ....................................................................... 1-31 (E)
2. Service Overview
2(E) DNE-1000
5. Cleaning
DNE-1000 3(E)
Manual Structure
Related manuals
Besides this Maintenance Manual Part 1, the following manuals are available for
DNE-1000.
4 (E) DNE-1000
Section 1
Installation
w w
Avoid placing or using this unit where it will be exposed to The power cord is not supplied with DNE-1000. Be sure to
greasy fumes, steam, dampness and dust environments. use the power cord that is applicable to places in the world.
If placing or using this unit in these environments, it may To avoid a fire or an electric shock, be sure to use the
cause a fire and an electric shock. designated power cord.
And do not damage to the power cord.
. The operating temperature is 5 dC to 40 dC.
For the customer in the U.S.A. and Canada
Do not install this unit near heat sources.
Required Parts
. To prevent a temperature rise inside the unit, pay careful DK-2401 (UC)
attention to circulation of air in the place where the unit 1 Power Cord, 125 V 10 A (2.4 m)
is installed. 2 Plug Holder B (Black) : 2-990-242-01
Do not block the ventilation holes on the outer cabinet.
AC inlet
1 2
Power requirements: 100 to 240 V AC ± 10% For the customer in the United Kingdom
50/60 Hz Required Parts
DK-2401 (EK)
Current consumption: 4.0 A maximum 1 Power Cord, 250 V 10 A (2.4 m)
(with all optional boards installed) 2 Plug Holder B (Black) : 2-990-242-01
n
As the inrush current at turn-on is the maximum 25 A, the
capacity of the AC power must be commensurate in it with
For the customer in the all European countries
the inrush current of the maximum 25 A. except the United Kingdom
If the capacity of the AC power is not the adequately large, Required Parts
the breaker of the AC power at the supply side will operate DK-2401 (AE)
1 Power Cord, 250 V 10 A (2.4 m)
or the unit will abnormal operate.
2 Plug Holder B (Black) : 2-990-242-01
AC inlet
1 2
n
For the customer outside of the area as shown above,
please consult with local Sony’s sale/service office.
DNE-1000 1-1(E)
1-3. Connectors
1-3. Connectors
Connector function Connector name and part Connector function Connector name and part
name on the rear panel number of matching cable name on the rear panel number of matching cable
PRIMARY INPUT BNC coaxial connector plug EDITOR Included with DNE-1000.
DIGITAL OUTPUT EDITOR D-sub 9-pin, Male
WORD SYNC OUTPUT Connector 9-pin, Male
REF IN 1-560-651-00
GPI D-sub 25-pin, Male Junction Shell 9-pin
Connector 25-pin, Male 1-561-749-00
1-560-904-11 FADER PANEL Included with BKNE-1011.
Junction Shell 25-pin
1-563-377-11
PANEL Included with DNE-1000. 1-3-3. BKNE-1011
GUI Transceiver Cable
1-559-701-11
Connector function Connector name and part
or name on the rear panel number of the matching cable
Micro Transceiver CONTROL PANEL Included with BKNE-1011.
Allied Telesis
Centre COM TM (*1)
MX10s (*1) : Centre COM is a trademark of Allied Telesis Corporation.
DEVICE CONTROL D-sub 9-pin, Male (*2) : Equivalent to CANNON XLR 3-12C.
Connector 9-pin, Male
(*3) : Equivalent to CANNON XLR 3-11C.
1-560-651-00
Junction Shell 9-pin
1-561-749-00
RS232C D-sub 9-pin, Female
Connector 9-pin, Female
1-563-815-21
Junction Shell 9-pin
1-561-749-00
AUX INPUT XLR 3-pin, Male
REF TC IN 1-508-084-00 (*2)
PGM OUT XLR 3-pin, Female
MONITOR 1-508-083-00 (*3)
REF TC IN
1-2(E) DNE-1000
1-4. Input and Output Signals of Connectors
1-4-1. DNE-1000
DEVICE CONTROL
F (LOCAL DISK) A (LOCAL DISK)
G B
REF IN
IN7 IN3
REC TC IN
H (LOCAL DISK) C (LOCAL DISK)
IN8 IN4
I D
J E
DIGITAL OUTPUT
PANEL GUI 2
2
AC IN
<EXT VIEW>
PRIMARY INPUT : SDI Digital video (BNC) MONITOR : (XLR 3-pin, Female)
DIGITAL OUTPUT : SDI Digital video (BNC) +4 dBm (600 Z at load), low impedance, balanced
Serial digital (270 Mbits/second)/SMPTE 259M/
ITU-R BT.656III REF TC IN : (XLR 3-pin, Male)
0.5 through 18 Vp-p, 10 KZ, balanced
WORD SYNC OUTPUT : (BNC)
Word clock, TTL level (48.0 kHz) AUX INPUT : AES/EBU Digital audio (XLR 3-pin, Male)
PGM OUT : AES/EBU Digital audio (XLR 3-pin, Female)
REF IN : Analog video (BNC, roop through out) AES/EBU format stereo mode, balanced
Black burst or composite sync
0.3 Vp-p, 75 Z, sync negative
DNE-1000 1-3(E)
1-4. Input and Output Signals of Connectors
n
(*1) <Controller> : indicates a controlling device.
(*2) <Device> : indicates a controlled device.
(*3) : Based on the Ethernet 10 BASE-5
(*4) : Based on the RS-232C DEVICE CONTROL from A to J (**6) :
(*5) : Based on the RS-422A RS-422A(*5) (D-sub 9-pin Female)
(*2)
<Device> from VTR, data servier and local strage
GUI : Ethernet 10 BASE-5 (*3) (D-sub 15-pin Female) (MAV-500) etc..
Pin No. Signal name Function Pin No. Signal name Function
Pin No. Signal name Function 3 PANEL RXA Received data (_)
4 PANEL TXB Transmitted data (+)
1 –– ––
5 PANEL TXA Transmitted data (_)
2 RXD Received data
6 –– ––
3 TXD Transmitted data
7 –– ––
4 –– ––
8 GND Ground
5 GND Ground
9 GND Ground
6 –– ––
10 METER+ Data for level meter + (*7)
7 RTS Request to send (Output)
11 +12 V Power supply +12 V
8 CTS Clear to send (Input)
12 METER_ Data for level meter _ (*7)
9 –– ––
13 +12 V Power supply +12 V
14 +12 V Power supply +12 V
15 GND Ground
1-4(E) DNE-1000
1-4. Input and Output Signals of Connectors
GPI R x
GPI R xG
x ; 1~4
DNE-1000 1-5(E)
1-4. Input and Output Signals of Connectors
1-4-2. BKNE-1010
<EXT VIEW>
n
(*1) <Controller> : indicates a controlling device.
(*2) <Device> : indicates a controlled device.
1 GND Ground
2 UNREG 6-12 V Power supply to BKNE-1011
3 SERIAL BUS FOR BAR LED (_) Sending data to BKNE-1011 (_)
4 SERIAL BUS FOR LED DRIVE Sending data to BKNE-1011
5 KNOB 1 (+) Knob data 1 from BKNE-1011 (+)
6 KNOB 2 (+) Knob data 2 from BKNE-1011 (+)
7 KNOB 3 (+) Knob data 3 from BKNE-1011 (+)
8 KNOB 4 (+) Knob data 4 from BKNE-1011 (+)
9 VIDEO FADER (+) Video fader data from BKNE-1011 (+)
10 AUDIO FADER-A Data of slide fader from BKNE-1011
11 AUDIO FADER-C Data of slide fader from BKNE-1011
12 AUDIO FADER-E Data of slide fader from BKNE-1011
13 GND Ground
14 +4 V Power supply +4 V to BKNE-1011
15 SERIAL BUS FOR BAR LED (+) Sending data to BKNE-1011 (+)
16 SERIAL BUS CLOCK Clock to BKNE-1011
17 SERIAL BUS LATCH PULSE Data to BKNE-1011
18 KNOB 1 (_) Knob data 1 from BKNE-1011 (_)
19 KNOB 2 (_) Knob data 2 from BKNE-1011 (_)
20 KNOB 3 (_) Knob data 3 from BKNE-1011 (_)
21 KNOB 4 (_) Knob data 4 from BKNE-1011 (_)
22 VIDEO FADER (_) Data of Video fader from BKNE-1011 (_)
23 AUDIO FADER-B Data of slide fader from BKNE-1011
24 AUDIO FADER-D Data of slide fader from BKNE-1011
25 FG E/N Data of connection evaluation for BKNE-1011
1-6(E) DNE-1000
1-4. Input and Output Signals of Connectors
1 GND Ground
2 TX KEY DATA (+) Transmitted data to DNE-1000 (+)
3 TX KEY DATA (_) Transmitted data to DNE-1000 (_)
4 RX KEY DATA (+) Received data from DNE-1000 (+)
5 RX KEY DATA (_) Received data from DNE-1000 (_)
6 –– ––
7 –– ––
8 GND Ground
9 GND Ground
10 SERIAL BUS LD (+) Received data from DNE-1000 to level meter (+)
11 +12 V Power supply +12 V from DNE-1000
12 SERIAL BUS LD (_) Received data from DNE-1000 to level meter (_)
13 +12 V Power supply +12 V from DNE-1000
14 +12 V Power supply +12 V from DNE-1000
15 GND Ground
1 –– ––
2 TXO Transmitted data
3 RXIN Received data
4 –– ––
5 GND Ground
6 –– ––
7 –– ––
8 –– ––
9 –– ––
DNE-1000 1-7(E)
1-4. Input and Output Signals of Connectors
1-4-3. BKNE-1011
CONTROL PANEL
13 1
25 14
<EXT VIEW>
1 GND Ground
2 UNREG 6-12 V Power supply from BKNE-1010
3 SERIAL BUS FOR BAR LED (_) Received data from BKNE-1010 (_)
4 SERIAL BUS FOR LED DRIVE Received data from BKNE-1010
5 KNOB 1 (+) Knob data 1 to BKNE-1010 (+)
6 KNOB 2 (+) Knob data 2 to BKNE-1010 (+)
7 KNOB 3 (+) Knob data 3 to BKNE-1010 (+)
8 KNOB 4 (+) Knob data 4 to BKNE-1010 (+)
9 VIDEO FADER (+) Data of video fader to BKNE-1010 (+)
10 AUDIO FADER-A Data of slide fader to BKNE-1010
11 AUDIO FADER-C Data of slide fader to BKNE-1010
12 AUDIO FADER-E Data of slide fader to BKNE-1010
13 GND Ground
14 +4 V Power supply +4 V from BKNE-1010
15 SERIAL BUS FOR BAR LED (+) Receiving data from BKNE-1010 (+)
16 SERIAL BUS CLOCK Clock from BKNE-1010
17 SERIAL BUS LATCH PULSE Data from BKNE-1010
18 KNOB 1 (_) Knob data 1 to BKNE-1010 (_)
19 KNOB 2 (_) Knob data 2 to BKNE-1010 (_)
20 KNOB 3 (_) Knob data 3 to BKNE-1010 (_)
21 KNOB 4 (_) Knob data 4 to BKNE-1010 (_)
22 VIDEO FADER (_) Data of video fader to BKNE-1010 (_)
23 AUDIO FADER-B Data of slide fader to BKNE-1010
24 AUDIO FADER-D Data of slide fader to BKNE-1010
25 FG E/N Data of connection evaluation for BKNE-1011
1-8(E) DNE-1000
LOCAL NETWORK
DNE-1000
Computer SDDI
SDI DIGITAL VIDEO
Overlay BKNE-1010 BKNE-1011 ANALOG VIDEO/AUDIO
(BKV-100) (Control Panel) (Fader Panel)
AES/EBU DIGITAL AUDIO
SONY SONY
Graphic ETHERNET
Ethernet I/F
RS-422A
Ethernet I/F
OTHR CONTROL
15-pin 25-pin
50 Z
EDITOR FADER CONTROL
PANEL PANEL
1-5-1. Stand Alone System
50 Z
(10BASE-2)
Local Storage System
MAU
REF TC IN
IN1
SDI IN SDDI OUT
IN2 SDI
BKSI-2020 PRIMARY PGM 1 SX VTR
IN3
ENC REMOTE INPUT PGM 2
IN4 SDI IN SDI OUT
SDI OUT 1 PGM 3 (DNW-A100)
SDDI IN IN5 SDI
2 DIGITAL REF REMOTE
BKSI-2030,2031 IN6 (BKNE EDIT PVW 1 75 Z ON
OUTPUT
AUDIO OUT 1/2 -1030) EDIT PVW 2
IN7
DEC-1 3/4
IN8 CAPTURE
SDDI IN SDI OUT 1
AES/EBU 1/2
DEC-2 2 1 PGM OUT 3/4 Audio A/D Conv.
SDI OUT 1 2 AES/EBU
SDDI IN MIC DIGITAL
BCN->XLR3 3 AUX INPUT MONITOR L
2 (DMA-2000) OUT
DEC-3 (ANALOG WORD
BCN->XLR3 4 AUDIO) R
SDDI OUT REMOTE A
BKNE-1040
SDDI IN B REF IN WORD 1
BKNE-1041 SYNC
SCSI BKSI-2010,2011 OUTPUT 2 DAT
SDC DIGITAL
REF TC IN DIGITAL
IN
OUT
DEVICE CONTROL WORD (PCM-7030)
MAV-S100/S110 REMOTE
SCSI (BKDS-1030)
A B C D E F G H I J
MAV-S100/S110
SCSI
SCSI TERMINATOR
1-5. Example of System Connection
1-9(E)
SERVER NETWORK
1-10(E)
Computer SDDI
SDI DIGITAL VIDEO
ON Air Buffer
Overlay BKNE-1010 BKNE-1011 ANALOG VIDEO/AUDIO
A
(BKV-100) (Control Panel) (Fader Panel) AES/EBU DIGITAL AUDIO
SONY SONY
B Graphic
Server ETHERNET
Ethernet I/F
SOURCE RS-422A
Ethernet I/F
OTHR CONTROL
1-5. Example of System Connection
(Title Super) 50 Z
EDITOR FADER CONTROL
PANEL PANEL
50 Z General
(10BASE-2) Purpose
Local Storage System I/F Unit
MAU
A B C D E F G H I J
MAV-S100/S110
SCSI
SCSI TERMINATOR
Server Control
DNE-1000
SERVER NETWORK
DNE-1000
SOURCE
50 Z General
(10BASE-2) Purpose
Local Storage System I/F Unit
MAU
1-5-3. Server System (Fast Transfer)
A B C D E F G H I J
MAV-S100/S110
SCSI
SCSI TERMINATOR
Server Control
1-11(E)
1-5. Example of System Connection
1-6. Attachment of DNE-1000
30.3
423.4
7
30.3
(Top view)
482
37.6
465
4-M4 (*1)
244.6
221.2
146
88.2
112
37.6
101.6
23.4
254
83.7 304.8
Unit : mm
(*1) : If using the packed screw of BVTT 4 x 8, this hole’s size is M4.
If not using if, this hole’s size is φ 3.5.
1-12(E) DNE-1000
1-6. Attachment of DNE-1000
c
1. Be sure to attach the unit in a stable place. If the unit is attached in a wobbly table or a slant surface,
the unit may be dropped. This may cause a injury.
2. Do not stack the units two or more. If the units two or more are stacked without the use of a rack, the
unit may be dropped. This may cause a injury.
3. Do not block ventilation holes on the outer cabinet. If blocking the ventilation holes, a temperature in
the unit rises. This may cause a fire.
For ventilation and maintenance, the rear side of the unit should be at lest 20 cm away from walls.
416 450
464
244.6
Board Extension board
When DNE-1000 is mounted in a rack, the maximum traveling distance is showed as below.
88.6
Unit : mm
DNE-1000 1-13(E)
1-6. Attachment of DNE-1000
1-14(E) DNE-1000
1-6. Attachment of DNE-1000
3. Loosen the screws secured the rear bracket to the outer 5. Fully press the inner members to the outer members
member. Adjust the positions of the front and rear while pressing the stoppers of the inner members and
bracket. attach the unit in the rack.
Rack
Rear bracket
Outer member
Front bracket
Outer member
Stopper
Inner member
4. Temporarily secure the front and rear brackets to the DNE-1000
outside of the rack by the eight screws (B5 x 8)
included with RMM-30.
6. After confirming that the unit can be moved smoothly,
Rack
tighten the eight screws (B5 x 8) temporarily secured
in the step 4.
Rack
12.7
n
When securing the front brackets to the rack by
31.75 Outer members
screws, pull out the unit about 20 cm (8 inches) from
12.7
the rack.
31.75
B5 x 8 Rack
Bracket Bracket B5 x 8
Unit : mm
Washers
RK5 x 16
DNE-1000
Washers
RK5 x 16
DNE-1000 1-15(E)
1-7. Attachment of Control Panel (BKNE-1010/1011)
237
BKNE-1010 225
10d
67.2
(Rear view) 15 48.3
202
183
18.3
26.6
(Top view)
(Right side view) Unit : mm
237
BKNE-1011 225
10d
67.2
(Rear view)
15 48.3
202
183
18.3
(Top view) 26.6
1-16(E) DNE-1000
1-7. Attachment of Control Panel (BKNE-1010/1011)
When attaching BKNE-1010/1011 in the console, drill to the console as in the following dimensions.
4.5
(10)
8
φ
2-
(202)
184
226
)
12
(R
(237)
Unit : mm
DNE-1000 1-17(E)
1-7. Attachment of Control Panel (BKNE-1010/1011)
Use the two D-sub cables included with DNE-1000 and BKNE-1011, and connect the control panel
(BKNE-1010/1011) to DNE-1000.
D-sub 15-pin cable (Included with DNE-1000) D-sub 25-pin cable (Included with BKNE-1011)
BKNE-1010 BKNE-1011
DNE-1000
DNE-1000 BKNE-1010
BKNE-1011
[PANEL] connector
(D-sub 15-pin Female)
1. BKNE-1010
(1) Select “MODE” switch at the rear side of BKNE-1010 to the 1.
(2) Connect the one D-sub 25-pin cable included with DNE-1000 between “PANEL” connector of DNE-
1000 and “EDITOR” connector of BKNE-1010.
2. BKNE-1011
(1) Connect the one D-sub 25-pin cable included with BKNE-1011 between “FADER PANEL” connec-
tor of BKNE-1010 and “CONTROL PANEL” connector of BKNE-1011.
1-18(E) DNE-1000
1-7. Attachment of Control Panel (BKNE-1010/1011)
(+) Driver
(Fig-1) (Fig-2)
BKNE-1011
DNE-1000 1-19(E)
1-8. Installation of Options
Optional Equipments for DNE-1000 DNE-1000 can be used for various systems, and its
functions can be extended by selecting the optional boards.
Each plug-in board must be installed in the corresponding
Option Function name
slot of DNE-1000.
BKNE-1030 Extended Fader Panel Confirm that all the plug-in boards are in the specified
(IF-609, XPT-9 board) slots by referring to the following table.
BKNE-1040 Video Effects Board For the details of how to install the plug-in boards, refer to
(SEC-39, VSW-45 board) “1-8-2. Inserting/Pulling Out of Plug-in Boards”.
BKNE-1041 3D/Lighting/Trail Effects Board
(VSE-22 board) The board name and the slot number in which the plug-in
boards can be installed are displayed near the eject lever at
the left and side on the A side of each plug-in boards. Like
the standard boards, each optional boards should also be
installed in the specified slot according to the slot number
display.
1 XPT-9
Board name
Eject lever
(A side)
m
1. Confirm that the connectors on each board are securely
connected to the MB-659 board of the main unit.
2. If the board is installed in an incorrect slot, a system
error occurs. Then the system is not activated properly.
3. Be sure to confirm the supply voltage when an option-
al board is added or a board is replaced.
(Refer to “1-11. Secondary Power Supply Voltage
Confirmation”.)
1-20(E) DNE-1000
1-8. Installation of Options
Plug-in Boards
XPT-9 BKNE-1030
1 Cross point board
APR-14
Audio process board
3
BKNE-1040
VSE-22 Special effect control board
4
BKNE-1041
SEC-39 Video special effect board
VSW-45 BKNE-1040
5 Video switcher board
7 (Not used)
8 (Not used)
IF-609
9 CPU-211 BKNE-1030
Interface board
System control board
DNE-1000 1-21(E)
1-8. Installation of Options
3. Open the eject levers of the plug-in board in the <Type 1>
direction of the arrow 1.
4. Pull out the plug-in board from the unit. This Type’s Optional Boards
n
Slot No. Optional board
Pull out the plug-in board with an equal force for both
eject levers. 1 XPT-9 board (BKNE-1030)
4 SEC-39 board (BKNE-1040)
5. Insert the plug-in board along the board guide rails 1. Install the optional board. (Refer to the section 1-8-2.)
while putting the eject levers to 1 position as shown
in the figure.
6. Connect the plug-in board to the connector on the
mother board while putting the eject levers in the
direction of the arrow 2.
7. Install the board retainer in the reverse order of the
steps 1 through 2.
n
When installing the board retainer, secure them with
the screws (B 3x6) that are packed with DNE-1000.
Eject levers
Board retainer
Board
BVTT Board guide rail
3x5
To pull out
1 the board
1-22(E) DNE-1000
1-8. Installation of Options
<Type 2>
The board name and the slot number in which the optional
boards can be installed are displayed at the left and side on
the A side of each optional boards.
After checking the installation direction of the optional
board, connect the optional board to the connectors on the
pre-installed board.
n
When installing the optional board, make sure that the
connectors are connected tightly. If the connectors cannot
be connected completely, the optional board may be placed
in the other way.
Slot 4
VSE-22 board
SEC-39 board
Slot 9
IF-609 board
CPU-211 board
DNE-1000 1-23(E)
1-9. Switch Settings on Boards and LEDs Description
COR2 (H14) : Watch dog timer setting CN16 (M2) : P-CPU test
Short ; Watch dog timer is disabled. This connector is used for the factory-shipped adjust-
Open ; Watch dog timer is enabled. ment. Do not use.
Factory-shipped setting; Open (Watch dog timer is enabled.)
CN20 (A10) : Confirmation of +5 V power voltage
COR4 (G1) : REF TC IN input impedance setting This connector is used for the confirmation of power
Short ; REF TC IN input impedance, about 680 Z voltage (GND) and for the factory-shipped adjustment.
Open ; REF TC IN input impedance, about 22 KZ Do not use.
Factory-shipped ; Open (REF TC IN input impedance,
about 22 KZ) CN21 (A9) : Confirmation of +5 V power voltage
This connector is used for the confirmation of power
CN4 (A15) : C-CPU test voltage (+ 5V) and for the factory-shipped adjustment.
This connector is used for the factory-shipped adjust- Do not use.
ment. Do not use.
CN701 (U16) : Test of E-CPU bus connection board
CN5 (A10) : C-CPU test This connector is used for the factory-shipped adjust-
This connector is used for the factory-shipped adjust- ment. Do not use.
ment. Do not use.
1-24(E) DNE-1000
1-9. Switch Settings on Boards and LEDs Description
DNE-1000 1-25(E)
1-9. Switch Settings on Boards and LEDs Description
F1 ; External interrupt
The interrupt (INT3) that may not occur occurs at the
C-CPU.
F2 ; Not used.
F3 ; Not used.
1-26(E) DNE-1000
1-9. Switch Settings on Boards and LEDs Description
OPEN
CN5 (A5) : GND
This connector is used when measuring.
1 2 3 4 5 6 7 8
DNE-1000 1-27(E)
1-9. Switch Settings on Boards and LEDs Description
1-10. Hard Reset (DNE-1000)
1. CPU-206 Board Open the front panel and push the system reset switch
S100 (A6) on the CPU-211 board, or turn OFF/ON the
power switch.
S1
1
RV1
TP2
TPE3
(A side/component side)
n
Select this switch from the connector panel side.
1-9-3. BKNE-1011
1. CPU-207 Board
CV1
(A side/component side)
1-28(E) DNE-1000
1-11. Confirmation and Adjustment of Secondary Power Supply Voltage
1-11-1. DNE-1000
DNE-1000 1-29(E)
1-11. Confirmation and Adjustment of Secondary Power Supply Voltage
6. If the specification does not meet, adjust the voltage as 2. Confirmation for voltage of +12 V
described below. It is not required to adjust a voltage of +12 V.
n If it is necessary to confirm the voltage, confirm the
The voltage adjustment is carried out with the digital voltage as described below.
voltmeter connected to the check terminals.
[Check procedures]
[Adjustment procedures] 1. Remove the fan cover on the rear panel.
1. Remove the two screws and the blind plate of the (Refer to the section 3-1-1.)
power supply unit. 2. Attach a digital voltmeter between 1-pin (+12 V) and
2. Put the tip of an adjustment driver from the adjustment 3-pin (GND) of the connector terminal (CN1 or CN2)
window and turn the adjustment potentiometer of the for a DC fan, and confirm that the voltage value meets
switching regulator. Turn the potentiometer to meet the following specification.
+1
the specification while monitoring the digital Specification : +12 _0 V
voltmeter.
n 3. After the confirmation, detach the two probes of the
After all required boards are attached to the unit, carry digital voltmeter and close the font panel.
out the adjustment of secondary power supply voltage.
Rear panel
3. After the adjustment, detach the probes of the digital
voltmeter, attach the blind plate and close the front
CN1
panel.
+12V 1-pin
GND 3-pin
+12V 1-pin
RV1
GND 3-pin
RV2
RV3 CN2
Adjustment driver
Blind plate
BVTT 3x5
1-30(E) DNE-1000
1-11. Confirmation and Adjustment of Secondary Power Supply Voltage
1-12. Initial Set-up of System
1. Detach the upper panel assembly. (Refer to the section For the initial set-up of system, refer to BZNE-1020
2-2-1.) Operation Program.
2. Attach the plus probe of a digital voltmeter to TP2 (+5
V) and the minus probe of it to TPE3 (GND) on the
CPU-206 board.
3. Confirm that the voltage meets the following
specification.
Specification : +5 +0.1
_0 V
BVWH 3x8
CN3
(GIZA TITE)
TPE3
(GND)
TP2
CPU-206 board (+5 V)
BVWH 3x8
(GIZA TITE)
DNE-1000 1-31(E)
Section 2
Service Overview
2-1. DNE-1000 (3) Push the hinge pin in the directin of the arrows while
holding the front panel, then remove the front panel.
2-1-1. Removal of Exterior Parts
Front panel
w
To avoid shock hazards and/or damage to the mounted
circuit boards, be sure to turn off the power switch, and
then turn off the breaker at the outside of DNE-1000 or
unplug the power cord before inserting or pulling out the
exterior parts.
1. Front Panel
(4) Install the front panel in the reverse order of the steps
(1) through (3).
2. Upper Chassis
M3 CASE
Upper chassis
BVTT 4x10
Front panel
BVTT 3x5
Rack angle
DNE-1000 2-1(E)
2-1. DNE-1000
2-1-2. Location of Main Parts
2-1-3. Capacitor for Data Backup
2-1-4. Spare Parts
CN-1254 board
RE-104 board
Fans
Power unit (Rear side)
To store a setup data and a real-time clock, the large This section describes the information for spare parts. In
storage capacitor (2 Farad) is mounted on the CPU-211 case of ordering replaceable parts such as mounted circuit
board. boards and major components, refer to the part numbers
To charge the large storage capacitor sufficiently, turn on and descriptions that are listed in this section.
the power of DNE-1000 for more than about thirty minutes.
The sufficiently charged large storage capacitor enables Spare Parts
data to be stored for about one week in the normal
Description Part No.
temperature.
Mounted Circuit Board, APR-14 A-8312-227-A
Mounted Circuit Board, CN-1254 A-8312-223-A
Mounted Circuit Board, CPU-211 A-8312-231-A
Mounted Circuit Board, IF-609 (BKNE-1030) A-8312-197-A
Mounted Circuit Board, IO-122 A-8312-225-A
Mounted Circuit Board, MB-659 A-8312-224-A
Mounted Circuit Board, SEC-39 (BKNE-1040) A-8312-216-A
Mounted Circuit Board, VIF-12 A-8312-229-A
Mounted Circuit Board, VSW-45 (BKNE-1040) A-8312-218-A
Mounted Circuit Board, XPT-9 (BKNE-1030) A-8312-195-A
Power Supply Unit A-8267-803-A
DC Fan (Rear side) 1-541-890-21
2-2(E) DNE-1000
2-2. BKNE-1010
2-2-1. Removal of Exterior Parts
2-2. BKNE-1010 3. Remove the four screws from the upper panel assem-
bly and the KY-343 board.
2-2-1. Removal of Exterior Parts
BVWH 3x8
(GIZA TITE)
c
. To avoid shock hazards and/or damage to the mounted
circuit boards, be sure to turn off the power switch of
DNE-1000 before inserting or pulling out the exterior BVWH 3x8
parts. (GIZA TITE) KY-343 board
. To avoid shock hazards and/or fire by a short circuit, be
sure to set the removed exterior parts on the places that
will not be established a short circuit.
Because the exterior parts are conductive-coated.
Lower case
Dial knob
PWH 3x6
CPU-206 board
Search dial
DNE-1000 2-3(E)
2-2. BKNE-1010
2-2-1. Removal of Exterior Parts
2-2-2. Location of Main Parts
2-2-3. Installation and Removal of Boards
7. Remove the three screws, and the pad and the upper panel. 2-2-3. Installation and Removal of Boards
c
PWH 3x6 To avoid shock hazards and/or damage to the mounted
circuit boards, be sure to turn off the power switch of
DNE-1000 before installing and/or removing the mounted
circuit board.
1. CPU-206 Board
Pad
8. Install the pad and the upper panel in the reverse order Upper panel assembly
of the steps 1 through 7.
KY-343 board
Search dial assembly
CN5
CN6
CN4
Harness clamp
Lower case
CN3
CPU-206 board
CPU-206 board
2-4(E) DNE-1000
2-2. BKNE-1010
2-2-3. Installation and Removal of Boards
2-2-4. Spare Parts
(3) Remove the three screws on the rear side and the three 2. KY-343 Board
screws on the CPU-206 board.
(1) Remove the upper panel assembly.
PTTWH 3x6 (Refer to the step 1 of the section 2-2-1.)
(S TIGHT) (2) Disconnect the one connector (CN3) on the CPU-206
board. (Refer to the step 2 of the section 2-2-1.)
CPU-206 board (3) Remove the four screws and the KY-343 board.
Harness (Refer to the step 3 of the section 2-2-1.)
clamp
(4) Disconnect the three connectors (CN1 through CN3)
on the KY-343 board.
KY-343 board
CN1
B 3x6
Lower case
B 3x8
CN2
(4) Remove the six hexagon screws, and the CN bracket
CN3
and the three plug covers.
Plug covers
Spare Parts
Hexagon screws
CN bracket
Description Part No.
(5) Install the CPU-206 board in the reverse order of the Mounted Circuit Board, CPU-206 A-8312-201-A
steps (1) through (4). Mounted Circuit Board, KY-343 A-8312-203-A
Search Dial Block Assembly A-6734-253-B
DNE-1000 2-5(E)
2-3. BKNE-1011
2-3-1. Removal of Exterior Parts
2-3. BKNE-1011 2. Remove the four knobs and the five slide knobs.
Fader grip
CPU-207 board
Lower case
CN7
BVWH 3x8
(GIZA TITE)
BVWH 3x8
(GIZA TITE)
2-6(E) DNE-1000
2-3. BKNE-1011
2-3-1. Removal of Exterior Parts
2-3-2. Location of Main Parts
5. Remove the two screws and the ENC bracket. 2-3-2. Location of Main Parts
6. Remove the four screws and the VR fitting bracket.
7. Remove the four screws and the fader assembly. SW-871 board
LD-77 board
BVWH 3x8
(GIZA TITE)
BVWH 3x8
ENC bracket (GIZA TITE)
BVWH 3x8
(GIZA TITE)
BV 3x10
(GIZA TITE)
Fader
assembly Faders
Fader assembly
CPU-207 board
8. Remove the three screws, and the pad and the upper
panel.
Pad
9. Install the pad and the upper panel in the reverse order
of the steps 1 through 8.
DNE-1000 2-7(E)
2-3. BKNE-1011
2-3-3. Installation and Removal of Boards
2-3-3. Installation and Removal of Boards (4) Remove the two screws on the rear side and the three
screws on the CPU-207 board.
c
To avoid shock hazards and/or damage to the mounted PTTWH 3x6
circuit boards, be sure to turn off the power switch of (S TIGHT)
CPU-207 board
DNE-1000 before installing and/or removing the mounted
circuit board.
1. CPU-207 Board
(1) Remove the fader grip, the four knobs and the five
slide knobs.
(Refer to the steps 1 and 2 of the section 2-3-1.)
(2) Remove the upper panel assembly.
(Refer to the step 3 of the section 2-3-1.) B 3x6
(3) Disconnect the seven connectors (CN2 through CN8)
and the flexible card wire (CN9) on the CPU-207 board.
Lower case
CPU-207 board
CPU-207 board
CN8 CN2
CN3
CN4
CN5
CN6
CN9 Plug cover
Hexagon screws
CN bracket
Lower case
CN7
(6) Install the CPU-207 board in the reverse order of the
steps (1) through (5).
2-8(E) DNE-1000
2-3. BKNE-1011
2-3-3. Installation and Removal of Boards
(1) Remove the fader grip, the four knobs and the five (1) Remove the fader grip, the four knobs and the five
slide knobs. slide knobs.
(Refer to the steps 1 and 2 of the section 2-3-1.) (Refer to the steps 1 and 2 of the section 2-3-1.)
(2) Remove the upper panel assembly. (2) Remove the upper panel assembly.
(Refer to the step 3 of the section 2-3-1.) (Refer to the step 3 of the section 2-3-1.)
(3) Disconnect the two connectors (CN7 and CN8) on the (3) Disconnect the two connectors (CN7 and CN8) on the
CPU-207 board. CPU-207 board. (Refer to the step 4 of the section 2-
(Refer to the step 4 of the section 2-3-1.) 3-1.)
(4) Remove the four screws and the VR fitting bracket. (4) Remove the two screws and the ENC bracket.
(Refer to the step 6 of the section 2-3-1.) (Refer to the step 5 of the section 2-3-1.)
(5) Disconnect the flexible card wire (CN1) on the LD-77 (5) Remove the two screws and disconnect the five
board. connectors (CN1 through CN5). Remove the SW-871
board.
SW-871 board
CN2
CN3
CN1
LD-77 board CN4
ENC bracket
CN1 CN5
LD-77 board
VR fitting bracket
DNE-1000 2-9(E)
2-3. BKNE-1011
2-3-4. Spare Parts
Spare Parts
2-10(E) DNE-1000
Section 3
Replacement of Main Parts
N
OW IO
FL TAT
AIRRO
B 4x30
Ferrite bead
(Serial numbers
4. Install a new power unit in the reverse order of the 10001 through 10050)
steps 1 through 3.
5. Confirm the secondary power supply voltage.
(Refer to the section 1-11.)
Fan cover B 3x30
DNE-1000 3-1(E)
3-1. DNE-1000
3-1-2. Replacement of Fan on the Rear Panel
3-2. BKNE-1010
3-2-1. Replacement of Search Dial
n 3-2. BKNE-1010
1. When installing the fan, take care the direction of the
airflow. c
2. When installing the fan, put the harness in the notch of To avoid shock hazards and/or damage to the mounted
the fan shown in the figure. circuit boards, be sure to turn off the power switch of
After installing the fan, insert the harness between the DNE-1000 before replacing the main parts.
upper fan and the lower fan. Pull the harness toward
the arrow A, then hold it with the ferrite bead. 3-2-1. Replacement of Search Dial
(Ferrite bead : For the units of the serial numbers from
10001 to 10050.) 1. Remove the upper panel assembly.
(Refer to the step 1 of the section 2-2-1.)
2. Disconnect the one connector (CN3) on the CPU-206
board. (Refer to the step 2 of the section 2-2-1.)
N
OW IO
FL TAT
AIRRO
3. Remove the dial knob rubber, the dial knob and the
search dial.
Air-flow (Refer to the steps 4 through 6 of the section 2-2-1.)
Notch direction 4. Disconnect the one connector (CN1) on the search
Fan
dial.
Notch
5. Remove the three screws and the JOG bracket.
Search dial
R RF
A
O
I
T O
A W
L
T
CN1
IO
N
CN2 A
Fan
JOG bracket CN1
Harness
Ferrite bead
(Serial numbers 10001 through 10050)
BVWH 3x8
(GIZA TITE)
3-2(E) DNE-1000
3-3. BKNE-1011
3-3-1. Replacement of Rotary Encoder
c (1) Remove the fader grip, the four knobs and the five
slide knobs.
To avoid shock hazards and/or damage to the mounted
(Refer to the steps 1 and 2 of the section 2-3-1.)
circuit boards, be sure to turn off the power switch of
(2) Remove the upper panel assembly.
DNE-1000 before replacing the main parts. (Refer to the step 3 of the section 2-3-1.)
(3) Disconnect the two connectors (CN7 and CN8) on the
3-3-1. Replacement of Rotary Encoder CPU-207 board.
(Refer to the step 4 of the section 2-3-1.)
1. Knob (4) Remove the four screws and the fader assembly.
(Refer to the step 7 of the section 2-3-1.)
(5) Remove the two screws (PSW 3x10, PSW 4x8) and
(1) Remove the fader grip, the four knobs and the five
the gear A.
slide knobs.
(6) Remove the three screws (B 2x4) and the rotary
(Refer to the steps 1 and 2 of the section 2-3-1.) encoder.
(2) Remove the upper panel assembly. (7) Remove the gear B from the rotary encoder.
(Refer to the step 3 of the section 2-3-1.)
(3) Disconnect the two connectors (CN7 and CN8) on the
CPU-207 board.
Rotary encoder
(Refer to the step 4 of the section 2-3-1.)
Gear B
(4) Remove the two screws and the ENC bracket.
(Refer to the step 5 of the section 2-3-1.)
(5) Disconnect the one connector of the rotary encoder to
Gear A
replace.
(6) Remove the nut of the rotary encoder to replace. PSW 3x10
Rotary encoder
B 2x4
PSW 4x8 Fader assembly
ENC bracket
Connector
Nut
DNE-1000 3-3(E)
3-3. BKNE-1011
3-3-2. Replacement of Fader
1. Fader Assembly (1) Remove the fader grip, the four knobs and the five
slide knobs. (Refer to the steps 1 and 2 of the section
(1) Remove the fader grip, the four knobs and the five 2-3-1.)
slide knobs. (2) Remove the upper panel assembly.
(Refer to the steps 1 and 2 of the section 2-3-1.) (Refer to the step 3 of the section 2-3-1.)
(2) Remove the upper panel assembly. (3) Disconnect the two connectors (CN7 and CN8) on the
(Refer to the step 3 of the section 2-3-1.) CPU-207 board. (Refer to the step 4 of the section 2-
(3) Disconnect the two connectors (CN7 and CN8) on the 3-1.)
CPU-207 board. (Refer to the step 4 of the section 2- (4) Remove the four screws and the VR fitting bracket.
3-1.) (Refer to the step 6 of the section 2-3-1.)
(4) Remove the four screws and the fader assembly. (5) Remove the two screws of the fader to replace.
(Refer to the step 7 of the section 2-3-1.) (6) Remove the each heat-shrinkable tube of harnesses to
(5) Install a new fader assembly in the reverse order of the replace the fader and desolder the harnesses.
steps (1) through (4).
Harness (soldering)
Heat-shrinkable tube
Fader
VR fitting bracket
B 3x4
(7) Install a new fader in the reverse order of the steps (1)
through (6).
n
When soldering the harness to the fader, put the heat-
shrinkable tube (ø3) through the harness.
3-4(E) DNE-1000
Section 4
Trouble Shooting (BKNE-1010/1011)
2. Test of LED
This test is confirmed to light all LEDs on the control
panel.
In the “4. Test of Communication” of the self diagnostics mode, the following connector tool is used.
This connector is connected between 2-pin and 4-pin, and between 3-pin and 5-pin of the D-sub 15-pin
female connector. (Other pins are opened.)
1 GND
2 TX KEY DATA (+)
3 TX KEY DATA (_)
4 RX KEY DATA (+)
[D-sub 15-pin . Female]
5 RX KEY DATA (_)
6 _ 8 1
7 _
15 9
8 GND
9 GND — EXT VIEW —
10 SERIAL BUS LD (+)
11 +12 V
12 SERIAL BUS LD (_)
13 +12 V
14 +12 V
15 GND
This connector is connected between 2-pin and 3-pin of the D-sub 9-pin female connector.
(Other pins are opened.)
1 _
2 TXO [D-sub 9-pin . Male]
3 RXIN 5
1
4 _
5 GND 6 9
6 _
7 _ — EXT VIEW —
8 _
9 _
BKNE-1010
“TL” key
P TL GO TO GO TO
“P” key IN OUT
-N +M
-1 +1 STILL PLAY “SEARCH DIAL”
“SHIFT” key
(Top view)
“FADER PANEL” connector “EDITOR” connector D-sub 15-pin (RS-422A)
“EDITOR” connector D-sub 9-pin (RS-232C)
“MODE” switch
(Rear view)
8 8 8 0 “1/2” LED
-1
-4
7 7 7 -6
“KNOB 1 to 4” 3 6 6 6
-10
-14
“3/4” LED
-20
5 5 5 -28
0 0 0
3. Test of MODE Switch and DC-IN (6 V) (1) Confirmation of D-sub 15-pin Connector (RS-422A)
(BKNE-1010) Connect the connector tool for loop back test to the D-
sub 15-pin connector and confirm that the transmitted
This test is confirmed to operate the audio fader Ref. data is received.
voltage selection mode by “MODE” switch and “DC IN
(6 V)” on the rear panel. n
The “AUDIO LEVEL METERs L and R” LEDs are used Do not connect to the D-sub 9-pin connector.
to confirm the operation. “(1) Confirmation of MODE
Switch” and “(2) Confirmation of DC IN (6 V)” are tested The transmitted data’s times are indicated the “AU-
at the same time until the [SHIFT] key is pressed . DIO LEVEL METER L” LEDs and the received
data’s times are indicated the “AUDIO LEVEL
n METER R” LEDs.
When carrying out “Test of Communication”, press the Confirm that the ten LEDs from the bottom of the
[SHIFT] key after connecting the connector tool for RS- “AUDIO LEVEL METERs L and R” light.
422A loop back test to the D-sub 15-pin of the “EDITOR”
connector. After the test, disconnect the connector tool for loop
back test from the D-sub 15-pin connector, re-connect
(1) Confirmation of MODE Switch it to the D-sub 9-pin connector and put the [SHIFT]
This confirmation is used the “AUDIO LEVEL key to go to “(2) Confirmation of D-sub 9-pin Connec-
METER R” LEDs. tor (RS-232C)”.
The “AUDIO LEVEL METER R” LEDs are indicated
the selection of the MODE switch on the rear panel. (2) Confirmation of D-sub 9-pin Connector (RS-232C)
The MODE 1 is selected.: All LEDs light off. Connect the connector tool for loop back test to the D-
The MODE 2 is selected.: The twenty LEDs from the sub 9-pin connector and confirm that the transmitted
bottom light. data is received.
(2) Confirmation of DC IN (6 V) n
This confirmation is used the “AUDIO LEVEL Do not connect to the D-sub 15-pin connector.
METER L” LEDs.
The “AUDIO LEVEL METER L” LEDs are indicated The transmitted data’s time are indicated the “AUDIO
whether the DC plug is plugged in the “DC IN (6 V)” LEVEL METER L” LEDs and the received data’s
or not. time are indicated the “AUDIO LEVEL METER R”
The DC plug is not plugged. : All LEDs light off. LEDs.
The DC plug is plugged. : The twenty LEDs from Confirm that the ten LEDs from the bottom of the
the bottom light. “AUDIO LEVEL METERs L and R” light.
4. Test of Communication (BKNE-1010) If the test conclusion is OK, the “3/4” LED lights. If the
test conclusion is NG, the “3/4” LED lights off and next
n goes to “5. Test of Switch” automatically.
Before this test, disconnect the connected cable (DNE-
1000) to the “FADER PANEL” on BKNE-1010 and plug
the AC adaptor to the “DC IN (6 V)”.
This test is carried out the loop back check of the RS-422A
and RS-232C of the “EDITOR” connectors and is con-
firmed the communication operation for them.
The communication operation of the RS-422A and RS-
232C is separately tested.
The confirmation of the operation is used the “AUDIO
LEVEL METERs L and R”, “3/4” LEDs.
This test is confirmed to operate the push button switches This test is confirmed the jog and shuttle operation of a
on BKNE-1010. The LED lights according to the pressed search dial. The confirmation of the operation is used the
switch. “INPUT”, “MIX” and “AUDIO LEVEL METERs L and
R” LEDs.
The confirmation of the operation is used the “AUDIO
LEVEL METERs L and R” LED. (1) Jog Mode
The LED lights while pressing a push button switch and Put the search dial to select into the jog mode.
lights off after releasing the push button. If turning the search dial clockwise(every 180d), the
twenty-five LEDs from the bottom of the “AUDIO
Every pressing a push button switch on the panel of LEVEL METER R” light in order according to the
BKNE-1010 without pressing the [SHIFT] key, the actuation of the search dial. If turning it counterclock-
“AUDIO LEVEL METER R” LEDs light according to the wise (every 180d), the twenty-five LEDs from the
push button switch. bottom of the “AUDIO LEVEL METER L” light in
order according to it.
If the test conclusion is OK, the LED of the [P] key lights.
If the test conclusion is OK (When turning the search
Every pressing a push button switch with pressing the dial clockwise and counterclockwise, all of the twenty-
[SHIFT] key, the “AUDIO LEVEL METER L” LEDs five LEDs light.), the “INPUT” LED lights.
light according to the push button switch.
(2) Shuttle Mode
If the test conclusion is OK, the LED of the [TL] key Put the search dial to select into the shuttle mode.
lights. If turning the search dial clockwise from the center
click position, the twenty-five LEDs from the bottom
of the “AUDIO LEVEL METER R” light in order
Push Button Number of LEDs of Audio Level
Switch Meter
according to the actuation of the seatch dial. If turning
it counterclockwise from the center click position, the
[P] 1
twenty-five LEDs from the bottom of the “AUDIO
[TL] 2
LEVEL METER L” light in order according to the
[GO|TO|IN] 3 actuation of the seatch dial.
[GO|TO|OUT] 4
–1 –N
5 If the test conclusion is OK (When turning the search
+1 +M
6 dial clockwise and counterclockwise, all of the twenty-
[STILL] 7 five LEDs light.), the “MIX” LED lights.
[PLAY] 8
[MARK|IN] 9
[MARK|OUT] 10
[REC] 11
[PVW] 12
[ADD] 13
[ALL|STOP] 15
This test is confirmed the transition operation of the audio 4-1-5. Ending the Self Diagnostics Mode
fader on BKNE-1011.
The “1”, 2", “3”, “4”, “M” and “AUDIO LEVEL METER After turning OFF the power switch of DNE-1000, turn
R” LEDs are used to confirm the operation. ON the power switch of DNE-1000.
This test starts in order from the audio fader of the “1”.
4-2. Trouble Shooting Any of the “1”, “2”, “3”, “4”, “M”, “KNOB”,
“LEVER”, “INPUT”, “MIX”, “1/2”, “3/4” and “L/R”
In the self diagnostics tests, the trouble that will erupt and LEDs (BKNE-1011) do not light or do not light off.
the source’s research are described.
. The IC1 or IC27 on the CPU-206 board is at fault or is
1. Trouble When Starting Self Diagnostics cold joints.
. The CN1 on the CPU-206 board is a cold joint.
The self diagnostics does not start. . The CN1 or CN9 on the CPU-207 board is a cold joint.
. The IC6 on the CPU-207 board is at fault or is a cold
. BKNE-1011 is not attached. joint.
. The CN1 on the LD-77 board is a cold joint.
. The IC1 on the LD-77 board is at fault or is a cold joint.
2. Trouble When Testing RAM . Any of the D1 through D12 on the LD-77 board are at
faults or are cold joints.
The internal RAM’s error.
The “AUDIO LEVEL METER L or R” LED does not
. The IC27 on the CPU-206 board is at fault. light or does not light off.
The external RAM’s error. . Any of the IC6, IC8 and IC27 on the CPU-206 board are
at fault or are cold joints.
. Any of the IC19, IC21 and IC28 on the CPU-206 board . The CN1 on the CPU-206 board is a cold joint.
are at fault. . The CN1 on the CPU-207 board is a cold joint.
. Any of the IC8, IC11 through 15, IC17 through 20, IC22
through 24, IC27, IC28, IC31, IC32 and IC56 on the
3. Trouble When Testing LED CPU-207 board are at fault or are cold joints.
. The CN9 on the CPU-207 board is a cold joint.
The [P] or [TL] key (BKNE-1010) does not light or . The harness between CN9 on the CPU-207 board and
does not light off. CN1 on the LD-77 board is not connected or is a poor
connection.
. The IC24 on the CPU-206 board is at fault or is a cold . Any of IC2 through IC5 on the LD-77 board are at fault
joint. or are cold joints.
. The Q5 ([P] key) or Q4 ([TL] key) on the CPU-206 . Any of D13 through D62 on the LD-77 board are at fault
board is at fault or is a cold joint. or are cold joints.
. The CN4 on the CPU-206 board is a cold joint.
. The harness (KEY1) between CN4 on the CPU-206
board and CN2 on the KY-343 board is not connected or
is a poor connection.
4. Trouble When Testing MODE Switch and DC- 6. Trouble When Testing Switch
IN (6 V)
If pressing a push button switch (BKNE-1010), the
If selecting the MODE switch (BKNE-1010), the “AUDIO LEVEL METER L or R” LEDs are not
“AUDIO LEVEL METER R” LEDs are not changed. changed.
. The S1 on the CPU-206 board is at fault or is a cold . The IC24 on the CPU-206 board is at fault or is a cold
joint. joint.
. The IC1 or IC24 on the CPU-206 board is at fault or is a . The CN5 or CN6 on the CPU-206 board is a cold joint.
cold joint. . The harness (KEY2) between CN5 on the CPU-206
board and CN1 on the KY-343 board is not connected or
The “AUDIO LEVEL METER L or R” LEDs are not is a poor connection.
changed by plugging and unplugging the “DC IN . The harness (KEY3) between CN6 on the CPU-206
(6V)”. board and CN3 on the KY-343 board is not connected or
is a poor connection.
. Any of the Q6, IC1 and IC24 on the CPU-206 board are . Any of the S1 through the S15 on the KY-343 board are
at fault or are cold joints. at fault or are cold joints.
. The J1 on the CPU-206 board is a cold joint.
. Any of the IC9, IC18 and IC27 on the CPU-206 board If moving the video fader lever (BKNE-1011), the
are at fault or are cold joints. “AUDIO LEVEL METER R” LEDs are not changed.
. The CN7 on the CPU-206 board is a cold joint.
. Any of the IC22, IC23 and IC25 on the CPU-206 board
are at fault or are cold joints.
. The CN1 on the CPU-206 board is a cold joint.
. The CN1 or the CN7 on the CPU-207 is a cold joint.
. The IC2 on the CPU-207 board is at fault or is a cold
joint.
. The connection between CN7 on the CPU-207 board and
video fader is not connected or is a poor contact.
. The video fader is at fault.
Clean periodically the filter at the back of the front panel The temperature in the set increases if dust is attached to
because it is apt to catch dust. the opening block of a fan and the air flow is disturbed.
It is recommended to replace the filter every five years. This may badly influence the performance and life of the
set.
1. Open the front panel. (Refer to “1. Front Panel” in the It is recommended to clean the fans every one month.
section 2-1-1.)
2. Peel the filter away from the adhesive tapes. 1. Fan of Front side
3. Remove dust on the filter using a vacuum cleaner.
n (1) Open the front panel. (Refer to “1. Front Panel” in the
If dust is caught leavily, it is recommended to wash the section 2-1-1.)
filter. (2) Remove dust on the fan and the power unit using a
When washing the filter, be sure to dry it well. vacuum cleaner.
Front panel
Adhesive tape
Fan
Filter
Adhesive tape
2. Fan of Rear side
(1) Remove dust on the fan and the fan cover using a
vacuum cleaner.
Fans
DNE-1000 5-1(E)
Section 6
Overall Block Diagrams
DNE-1000 6-1
DNE-1000 OVERALL Block Diagram
6-1. DNE-1000
IN 4
IN 3
IN 2
IN 1
XPT-9 VIF-12
Control Control
I/F I/F
S/P
S/P
S/P
S/P
S/P
S/P
S/P
S/P
Frame Output Audio
Delay Proc. Combine
TBC
TBC
TBC
TBC
TBC
TBC
TBC
TBC
Frame Output
Delay Proc.
KEYER
PGM DMX
PVW
CAP
DSKS
DSKF
EXTK
FM1I
FM2I
VITC
EAA
EAB
EAR
6-2 DNE-1000
Block Diagram DNE-1000 OVERALL
IF-609
D CPU 4 D CPU 3 D CPU 2 D CPU 1 D CPU 0 P CPU
ADRS
DATA
PGM Out(D) CONTROL
EDH 10
/ P/S C CPU BUS
ADD.
Pattern Gen.
1/2
Emphasis
/ Sep. 3/4
Pitch Control
1/2
Equalizer
EAR 10 Audio
/ Sep. 3/4 WORD
Audio SYNC
Timing
GEN.
Monitor
Adder
Fader
1/2
AES/EBU ENC
AES/EBU ENC
AES/EBU
AES/EBU
AES/EBU
AES/EBU
DEC
DEC
DEC
DEC
CONV
CONV
CONV
RATE 1/2
RATE 1/2
RATE 1/2
RATE 1/2
Gen.
APR-14
1/2 3/4
To Panel
1 2 3 4 CH1 CH2
AUX AUDIO INPUT MONITOR PGM OUT
DNE-1000 6-3
BKNE-1010 OVERALL Block Diagram
6-2. BKNE-1010
DC-DC 12.288MHZ
J1 6-12V
AC ADAPTOR IC2
5V
X1
Q1 ,2 ,3
CN2
CPU
RS-422A
TO DNE-1000 DRIVER/ HD647180
(D-SUB 15-PIN MALE) RECEIVER IC27 ADDRESS BUS
CONTROL
CN7
RS-232C
(*1) DRIVER/
RECEIVER
IC18
SERIAL
CONVERTER
IC29
CN1
RS-422A SELECTER
DRIVER/
IC8
RECEIVER
TO BKNE-1011 BAR LED
IC6
(D-SUB 25-PIN FEMALE)
STATUS LED
6-4 DNE-1000
Block Diagram BKNE-1010 OVERALL
DIAL ASSY
A/D CONVERTER COUNTER PIO DIAL
REF. COUNTER
IC4 IC10 ,12 ,23 IC24
IC15
VOLTAGE
SELECTER
S1
RY1 IC14
Q6 ,7
KEY SW
LED
KY-343
CPU-206
DNE-1000 6-5
BKNE-1011 OVERALL Block Diagram
6-3. BKNE-1011
ENCODER
BUFFER
SW-871
CN1
IC2,7
STATUS LED
VIDEO FADER ASSY
FROM BKNE-1010 BAR LED
BUFFER
IC6
SHIFT
REGISTER
RS-422A BAR LED
RECEIVER
CONTROL IC1,2,3,
4,5
IC11,14,15,17,
18,19,22,23
X1
IC8
REG
5V LD-77
IC10
AUDIO FADER
BUFFER
FADER VR 10K/B
IC3,4
CPU-207
6-6 DNE-1000
SAFETY CHECK-OUT
AC
0.15 µF 1.5 kΩ voltmeter
(5.25V)
Earth Ground