Beruflich Dokumente
Kultur Dokumente
Sony TX7 CCUmanual
Sony TX7 CCUmanual
CCU-TX7
CCU-TX7P
CAMERA OPERATION UNIT
COU-TX7
SDI OUTPUT BOARD
DXBK-701
SERVICE MANUAL
Volume 1 1st Edition (Revised 2)
! WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
! WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
! AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
CCU-TX7 (E)/V1
MANUAL STRUCTURE
Purpose of this manual This manual is the Service Manual Vol. 1 of the CAMERA CONTROL UNIT CCU-TX7
(for NTSC) and CCU-TX7P (for PAL), CAMERA OPERATION UNIT COU-TX7 and SDI
OUTPUT BOARD DXBK-701.
This manual contains the operation manual related to the operations of this equipment,
the replacement of the parts and adjustments.
Related manuals In addition to this Service Manual Vol. 1, the following manual is provided.
CCU-TX7 (E)/V1 1
TABLE OF CONTENTS
1. OPERATING INSTRUCTIONS
2. INSTALLATION
3. SERVICE INFORMATION
4. ADJUSTMENT
CCU-TX7 (E)/V1
4
4-7. TRIAX INTERFACE SYSTEM ADJUSTMENT ....................................... 4-27
4-7-1. Frequency Set Adjustment ................................................................... 4-27
4-7-2. INCOM Deviation Adjustment ............................................................ 4-28
4-7-3. PGM Deviation Adjustment ................................................................. 4-28
4-7-4. INCOM Demodulation Adjustment ..................................................... 4-29
4-7-5. INCOM Level Adjustment ................................................................... 4-29
4-7-6. MIC 1 Demodulation Adjustment ........................................................ 4-30
4-7-7. MIC 1 Level Adjustment ...................................................................... 4-30
4-7-8. MIC 2 Demodulation Adjustment ........................................................ 4-31
4-7-9. MIC 2 Level Adjustment ...................................................................... 4-31
4-7-10. CAM DATA Demodulation Adjustment ............................................. 4-32
4-7-11. CAM TONE Adjustment ...................................................................... 4-32
CCU-TX7 (E)/V1
5
CCU-TX7 (E)/V1
1-1. CCU-TX7/TX7P
3-859-845-12(1)
Camera Control
Unit
OPERATING INSTRUCTIONS
Operating Instructions
Before operating the unit, please read this manual
thoroughly and retain it for future reference.
SECTION 1
CCU-TX7/TX7P
1997 by Sony Corporation
1-1
1-2
Table of Contents
For the customers in the USA
WARNING
This equipment has been tested and found to comply with Over view ............................................................................ 4
To prevent fire or shock hazard, do not the limits for a Class A digital device, pursuant to Part 15 of
expose the unit to rain or moisture. the FCC Rules. These limits are designed to provide Product Features .................................................................. 4
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This Connections ......................................................................... 5
equipment generates, uses, and can radiate radio frequency Installing the Camera Operation Unit ................................. 7
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio Location and Function of Par t s ....................................... 8
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the Front Panel .......................................................................... 8
user will be required to correct the interference at his own
expense.
Rear Panel ......................................................................... 14
Internal Board Switches and Knobs .................................. 17
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority Notes on Use ................................................................... 20
to operate this equipment.
Specifications .................................................................. 21
This device requires shielded interface cables to comply with
FCC emission limits.
Owner’s Record
2
3
CCU-TX7 (E)/V1
Over
Over viewview
The CCU-TX7/TX7P is a camera control unit that Examples of how to connect other devices to this unit • Some of the video camera’s switches and buttons
connects to DXC-637 Series and DXC-D30 Series are shown in the following. may not operate while the CCU-TX7/TX7P is
Color Video Cameras via the CA-TX7/TX7P Camera connected to it.
Adaptor. Notes
This product’s features are described below. • Be sure to power the CCU-TX7/TX7P off before For details, see the operation instructions for the video
inserting or removing the triaxial cable connector. camera or camera adaptor.
Full-featured signal transfer functions
• The CCU-TX7/TX7P is able to transfer wideband When using one CCU-TX7/TX7P unit
component video signals. (Y signals at 9 MHz or
above, and R–Y and B–Y signals at 4.5 MHz or
above) Out
• When using a triaxial cable, audio signals can be In
transferred up to 750 meters (2461 feet) (when cable In
diameter is 8.5 mm (11/ 32 inch)) or 1,500 meters (4921 Control console
In
feet) (when cable diameter is 14.5 mm (19/32 inch)). Headset
In/Out
• Transfer functions are provided for the following
signals. Headset
Return video, teleprompter signal, microphone audio,
program audio, red tally and green tally signals CA-TX7/TX7P
• An intercom switch is also provided. DXC-D30/D30P
Y/R–Y/B–Y,1) RETURN
MIC VIDEO
R/G/B,Y/C
Flexibly adaptable camera control functions INTERCOM/ OUT
• The optional COU-TX7 Camera Operation Unit, TALLY VBS
which can be installed on the CCU-TX7/TX7P’s
front panel, enables video camera operations to be INTERCOM (front panel)
controlled from the CCU-TX7/TX7P. Reference sync signal
• When several CCU-TX7/TX7P units are connected in
GENLOCK
parallel, the optional RCP-TX7 Remote Control CAMERA
Panel can be used to control video camera operations Triaxial cable PROMPT
VIDEO
as well as the color balance between cameras. Teleprompter signal
• An RS-232C connector is provided for the CCU-
CCA-7 cable
TX7/TX7P, allowing a personal computer to be
connected for computer-based control of video REMOTE DC IN
4 5
1-3
1-4
Over view
When using two CCU-TX7/TX7P units Installing the Camera Operation Unit
The following describes how to fit the optional COU-
Switcher, video
TX7 Camera Operation Unit to the CCU-TX7/TX7P’s
monitor, etc. front panel.
DXC-D30/D30P
VCR
Y/R–Y/B–Y,R/G/B,Y/C 1)
1 Open the CCU-TX7/TX7P’s
VBS Chroma keyer front panel.
CCA-7 cable
PROMPT
(For power sources,
REMOTE VIDEO
see the connections
RETURN illustrated for the unit
CCU/CAMERA
VIDEO shown below.)
CCU-TX7/TX7P 3) RS232C
GENLOCK 2 Remove the blank panel and
the connector cap. Stopper
VBS
Chroma keyer
GEN
LOCK
CA-TX7/TX7P
CAMERA
Triaxial cable RETURN
VIDEO
PROMPT
3 Attach the camera operation
CCA-7 cable VIDEO unit to the front panel and
connect the flat cable to the
REMOTE
DC IN connector. Flat cable
CCU/CAMERA
DC power
CCU-TX7/ SDI AC IN source 2)
TX7P 3) OUT4)
Camera
AC power cord operation unit
RS232C
(supplied)
AC power source 2)
Waveform monitor
1) Y/R–Y/B–Y, R/G/B, and Y/C outputs are switchable. with SDI input
2) Use either AC or DC power source.
3) This illustration shows the CCU-TX7.
4) Using the SDI OUT connectors requires the optional Switcher with SDI input
DXBK-701 board.
6 7
CCU-TX7 (E)/V1
CCU-TX7 (E)/V1
Location
Location and Function
and Function of Par t s of Parts
Various switches, adjustment knobs, and connectors CCU-TX7/TX7P switches and knobs You can then talk with the operator via the intercom.
are located on the front panel, rear panel, and also on This button also lights when the CALL button is
the edges of internal boards. pressed on the camera adaptor or remote control panel.
1 TALLY lamp
TALLY CABLE ALARM 4 INTERCOM audio input/output and setting
SHORT OPEN
2 CABLE ALARM indicator section
Front P anel
CALL
3 CALL button MIC switch
From the front panel, you can operate the CCU-TX7/ For description of how to install the camera operation unit, INTERCOM
CAMERA INTERCOM
TX7P’s switches and knobs as well as the camera see “Installing the Camera Operation Unit” (page 7). POWER
MIC LINE MIC LINE
ON CH1 ON CH1
operation unit’s switches and knobs (when the optional PRIV
PRIV
LINE switch
ON OFF CH2
COU-TX7 Camera Operation Unit has been installed). INTERCOM PGM OFF
INTERCOM
CH2
PGM
OFF 4 INTERCOM audio input/
output and setting section PGM knob
5 CAMERA POWER switch
CCU-TX7/TX7P switches and knobs POWER
PUSH
and indicator INTERCOM knob
(see page 9)
PUSH
Camera operation unit switches and knobs
(see page 10)
INTERCOM connector
6 POWER switch and
indicator
TALLY CABLE ALARM OPERATE OUTPUT GAIN TLCS
SHORT OPEN LOCK HIGH
CAM
1 TALLY lamp
PART MID
FULL BARS
SHUTTER
LOW
SKIN M.GAMMA
INTERCOM connector (XLR 5-pin): Use this to
CALL
DETAIL The lamp lights red when a red tally signal is received connect a headset.
Hz
C.SCAN
ON
ON
OFF
and green when a green tally signal is received. INTERCOM (intercom level) knob: Use this to
OFF
CAMERA INTERCOM
POWER
MIC LINE WHITE/BLACK BALANCE
DETAIL
It also lights red when the CALL button is pressed on adjust the intercom sound volume.
ON CH1
PRIV
AUTO WHITE AUTO
PRE
ATW
the CA-TX7/TX7P Camera Adaptor or RCP-TX7 PGM (program audio level) knob: Use this to
ON OFF
INTERCOM
CH2
PGM
MANUAL BLACK MANUAL Remote Control Panel connected to this unit. adjust the sound volume when monitoring
OFF
BLACK WHITE
The camera number plate (provided) can be attached to program audio via a headset.
KNEE MASTER
BLACK
IRIS this lamp. MIC switch: Use this switch to turn the headset’s
AUTO AUTO
POWER
PUSH
microphone ON or OFF.
1
PRESET MANUAL
Camera operation unit switches and knobs 3 SHUTTER setting section 4 WHITE/BLACK BALANCE control section
10 11
CCU-TX7 (E)/V1
CCU-TX7 (E)/V1
WHITE AUTO/PRE/MANUAL (white balance WHITE (white balance) knob (blue) !™ IRIS control section !£ DIP switch
auto/preset/manual) switch When the WHITE AUTO/PRE/MANUAL switch is Use the four switches numbered 1 to 4 to make the
Use this switch to select the white balance adjustment set to MANUAL, this knob can be used to adjust the following settings.
IRIS AUTO/MANUAL switch
mode. This switch does not function while the ATW gain of the B signal.
function is being used (while the ATW button is lit). IRIS No.1 OFF/No.2 OFF Standard color matrix setting
AUTO
No.1 OFF/No.2 ON (This setting has no effect when a
AUTO: This sets auto adjustment mode. It enables 5 KNEE switch DXC-D30 series video camera is
the white balance to be automatically adjusted Use this switch to adjust the knee setting. MANUAL connected.)
using the WHITE/BLACK switch. AUTO: Knee is automatically adjusted No.1 ON/No.2 OFF Color matrix set for fluorescent
(When a DXC-637 series video camera is PRESET: Knee is adjusted to preset value lighting (FL).
(This setting has no effect when a
connected: this also sets auto adjustment mode DXC-D30 series video camera is
for the black balance. The black balance can be 6 MASTER BLACK knob Iris adjustment knob connected.)
automatically adjusted even while the ATW This adjusts the master black (master pedestal level) No.1 ON/No.2 ON Color matrix set for color emphasis
function is being used.) setting. The click position of the knob provides a (H.SAT).
PRE: This sets preset mode. The white balance is typical setting. IRIS AUTO/MANUAL switch (This setting has no effect when a
DXC-D30 series video camera is
maintained at the preset value. Use this switch to select between AUTO and connected.)
(When a DXC-637 series video camera is 7 GAIN switch MANUAL iris adjustment modes. Be sure that the
No.3 ON EVS function set on for the shutter.
connected: this also sets auto adjustment mode Use this switch to set any of three video amp gain IRIS switch on the video camera is set to AUTO. (Has priority over the SHUTTER
for the black balance. The black balance can be levels (HIGH, MID, or LOW). The gain value AUTO: Iris is automatically adjusted. switch setting on the camera
automatically adjusted even while the ATW MANUAL: Iris is adjusted with the iris adjustment operation unit.)
corresponding to these levels can be set using a menu
function is being used.) on the video camera. knob. No.4 ON Date and time display set on for the
output picture.
MANUAL: Sets manual adjustment mode. It
enables the white balance to be manually adjusted 8 TLCS (total level control system) switch Iris adjustment knob
using the WHITE knob (red) and WHITE knob Press this switch to turn the total level control system When the IRIS AUTO/MANUAL switch is set to
(blue). on or off. The switch lights when it is turned on. When MANUAL, this knob can be used to manually adjust
(When a DXC-637 series video camera is this switch is on, settings made with the GAIN switch the iris.
connected: this also sets manual adjustment mode and SHUTTER switch are ignored. When the IRIS AUTO/MANUAL switch is set to
for the black balance. The black balance can be (This function cannot be used when a DXC-637 series AUTO, this knob can be used to manually fine-tune
adjusted manually even while the ATW function video camera is connected.) the automatic iris adjustment.
is being used.)
9 M. GAMMA (master gamma) knob
ATW (auto tracing white balance) button Use this knob to adjust the gamma curve. The click
Press this button (which lights up when pressed) to position of the knob provides a typical setting.
have the white balance adjusted automatically when (This function cannot be used when a DXC-637 series
lighting conditions change. video camera is connected.)
12 13
1-7
1-8
Rear Panel 8 RS232C connectors (D-sub 25-pin) WF (waveform monitor output) connector
There are two connectors, CH1 and CH2. You can use Use this connector to output a video signal to a
these connectors to connect a personal computer to waveform monitor. Use the MONITOR SELECT
control the video camera. button on the RCP-TX7 Remote Control Panel to set
You may also use these connectors to connect this unit the type of signal to be output. Selection of the signal
9 OUTPUT connectors
to another CCU-TX7/TX7P unit. It is possible to carry type also applies to the output from the PIX connector.
out color balancing or linked iris adjustment between
PGM IN OUTPUT
CAMERA
VBS1 1 R/R-Y/C 2
!º Fan two or more interconnected CCU-TX7/TX7P units SPARE connector
INPUT GENLOCK
using the RCP-TX7 Remote Control Panel. This connector is not used (it is reserved for future
1 PGM IN connector ON
VBS2 1 G/Y/Y 2 OFF
75Ω use).
ON
1
For details, refer to the operating instructions for the RCP-
RTS PIX 1 B/B-Y 2 OFF
75Ω
RETURN VIDEO
!¡ INPUT connectors TX7. 0 Fan
2 CAMERA connector and 75 Ω termination
WF SYNC SPARE
ON
OFF
2 switches A cooling fan is built in.
9 OUTPUT connectors (BNC type)
75Ω
3 RTS connector
ON
COAX
MIC OUT
OFF
75Ω
Note
4 COAX connector PROMPT VIDEO
!™ MIC OUT connectors
CH1 CH2
R/R–Y/C, G/Y/Y, and B/B–Y connectors If the fan should fail, the CAMERA POWER indicator
REMOTE WF MODE DC IN
OUTPUT
5 REMOTE connector !£ DC IN connector VBS1 1 R/R-Y/C 2 flashes. Immediately switch off the power, and consult
6 WF MODE connector INTERCOM/TALLY 1
SDI
2 your supplier Sony dealer for repair. Continuing to use
OUT AC IN !¢ SDI OUT connectors
VBS1 and VBS2 connectors VBS2 1 G/Y/Y 2 the unit when the fan is defective may shorten the life
7 INTERCOM/TALLY CH1
RS232C
CH2
of the equipment.
connector
PIX 1 B/B-Y 2
BREAKER
!∞ AC IN connector
PIX connector !¡ INPUT connectors (BNC type) and 75-Ω
8 RS232C connectors
WF SYNC SPARE termination switches
!§ Breaker switch
WF connector This section includes four pairs of loop-through
connectors and corresponding 75-Ω termination
Illustration: CCU-TX7 SPARE connector switches.
GENLOCK
SYNC connector INPUT
ON
1 PGM IN (program audio input) connector (XLR Internal board settings must be changed before using this OFF
75Ω
GENLOCK connectors
3-pin) connector. For details, contact a Sony dealer. R/R–Y/C, G/Y/Y, and B/B–Y (component video 1
ON
The program audio signal is input via this connector. signal/RGB signal/Y and C signal output) OFF
75Ω
5 REMOTE (remote control panel) connector (10- connectors RETURN VIDEO RETURN VIDEO 1 and
ON RETURN VIDEO 2 connectors
2 CAMERA connector (triaxial) pin) Use these connectors to output the signals from the OFF
75Ω 2
Connect a triaxial cable here to connect this unit to the Use this connector to connect the RCP-TX7 Remote video camera as component signals (R–Y, B–Y, and ON
CA-TX7/TX7P Camera Adaptor attached to a video Control Panel via a CCA-7 cable. Y), RGB signals for chroma keying, or Y and C OFF
75Ω
PROMPT VIDEO connectors
camera. signals. Use a switch on an internal board (ES-20) to PROMPT VIDEO
!§ Breaker switch
If the input current exceeds 10 A during operation of
the unit on a DC power source, the breaker is actuated
to shut off the power supply. To resume operation,
push in the breaker switch after making sure the input
current does not exceed 10 A.
16 17
1-9
1-10
1 ES-20 board 2 AA-90 board INTERCOM (intercom system select) switches PANEL (panel control) switch
Use these switches to select the type of external When the COU-TX7 Camera Operation Unit has been
intercom system to be used. Set the upper switch to installed on this unit while the RCP-TX7 Remote
4W if no external intercom is connected. Control Panel is also connected to the unit, use this
ES-20 If you set the upper switch to RTS, select either RTS switch to select the camera operation unit or the
AA-90
PHASE
H PGM IN or CLEARCOM with the lower switch. remote control panel as the control device.
0dB
H PHASE adjustment screw -20dB
PGM IN switch REMOTE: Enables the video camera to be
SC
MIC 1 LEVEL
0dB
3 CT-181 board controlled from the remote control panel.
0
SC PHASE switch and fine-tuning screw -20dB LOCAL: Disables remote control (via the remote
MIC 2 LEVEL MIC 1 LEVEL and MIC 2 LEVEL
180
0dB
switches
control panel) of the video camera.
-20dB
OUTPUT 1 MIC TEST
R/G/B CH1
Y/R-Y/B-Y CH2
MIC TEST switch CT-181 CONTROL MODE switch
Y/C OFF
OUTPUT 1 and OUTPUT 2 switches R TALLY
If another CCU-TX7/TX7P unit is connected to this
OUTPUT 2 LEVEL IND CONTACT
R/G/B
Y/R-Y/B-Y
Y/C LEVEL IND indicators
POWER
unit, use this switch to select whether the video camera
DC24V
TTL
is controlled directly from this unit or from the other
INTERCOM G TALLY R TALLY and G TALLY CCU-TX7/TX7P unit.
2W CONTACT
CLEAR
COM RTS POWER
switches NORMAL: Video camera is controlled directly from
4W
INTERCOM switches
RTS
DC24V this unit.
TTL
CLEAR
COM SLAVE: Video camera is controlled from other
MIC GAIN
NORM
MIN CH1
CCU-TX7/TX7P unit.
MAX
NORM
MIC GAIN adjustment screws This switch does not operate when the RCP-TX7
CH2
MIN
MAX Remote Control Panel is connected to this unit. In this
H PHASE (horizontal phase) adjustment screw PGM IN (program audio input level setting) PANEL
REMOTE case, use the remote control panel to make the above
Turn this screw with a screwdriver to adjust the switch LOCAL PANEL switch
selection.
CONTROL MODE
horizontal phase alignment between an external sync Use this switch to set the program audio input level to NORMAL
SLAVE CONTROL MODE switch
signal and the output signal. 0 dB or –20 dB.
SC PHASE (subcarrier phase setting) switch MIC 1 LEVEL and MIC 2 LEVEL switches
and fine-tuning screw Use these switches to set the microphone output levels
Use this switch and screw to adjust the output signal for channel 1 (CH1) and channel 2 (CH2) to 0 dB or R TALLY (red tally) and G TALLY (green tally)
subcarrier phase with respect to an external sync –20 dB. switches
signal. After setting the SC PHASE switch, turn the Set these switches to CONTACT (to use contact
fine-tuning screw to make fine adjustments. MIC TEST switch signals) or POWER (to use voltage signals) for the red
Set this switch to CH1 or CH2 to mix that channel’s tally and green tally. If you set them to POWER, select
OUTPUT 1 and OUTPUT 2 switches microphone signals from the video camera with the either DC24V or TTL.
Use these switches to select the type of signal to be program audio, so that the mixed input can be
output via the OUTPUT connectors (R/R–Y/C, G/Y/Y, monitored via a headset connected to this unit or a MIC GAIN adjustment screws
B/B–Y). The OUTPUT 1 switch corresponds to the camera adaptor. This switch is used to check the Use these screws to adjust the microphone amplifier
three OUTPUT connectors on the left side and the microphone signals. gain for the camera adaptor. The standard level
OUTPUT 2 switch to the three OUTPUT connectors (NORM) is 0 dB, and the gain setting can be adjusted
on the right side. LEVEL IND (microphone level) indicators to any of 16 levels from –12 dB (MIX) to +12 dB.
R/G/B: Selects output of R, G, and B signals from The transfer levels for microphone signals (CH1 and Adjust the gain so that, on the AA-90 board, the green
the OUTPUT connectors. CH2) are indicated by colors. The upper indicator and orange LEVEL IND indicators are lit while the
Y/R–Y/B–Y: Selects output of R–Y, Y, and B–Y corresponds to channel 1 (CH1) and the lower one to audio level is normal with the red indicator lighting
component signals from the OUTPUT connectors. channel 2 (CH2). only when the maximum audio level is reached. If the
Y/C: Selects output of Y and C signals from the Green: Approximately –12 dB to 0 dB red indicator does not light at all, or if the orange
OUTPUT connectors. Orange: Approximately 0 dB to +12 dB indicator lights only intermittently, raise the gain level.
Red: Approximately +12 dB or higher If the red indicator stays lit, lower the gain.
Use these indicators along with the MIC TEST switch
to check microphone signal lines or as a adjustment
indicator when adjusting the microphone gain with a
MIC GAIN adjustment screw on the CT-181 board.
18 19
CCU-TX7 (E)/V1
CCU-TX7 (E)/V1
Notesand
Location onFunction
Use of Parts Specifications
Use and storage locations Do not cover with cloth General MIC OUT XLR 3-pin (2)
Avoid using or storing the unit in the following places: While the unit is in operation, do not cover it with a 0 dBu/–20 dBu balanced,
• Where it is subject to extremes of temperature cloth or other material. This can cause the temperature Power requirements 2 channels
(operating temperature: 5°C to 40°C (41°F to to rise, leading to a malfunction. CCU-TX7: 120 VAC, 50/60 Hz Y/C 1) BNC type (2 each)
104°F)). CCU-TX7P: 220 to 240 VAC, 50/ Y: 1.0 Vp-p, 75 Ω
Note that in summer the temperature in a car with the After use 60 Hz, 0.45 A C: 286 mV (CCU-TX7)/300 mV
windows closed can reach 50°C (122°F). Turn the unit off. 10.5 to 17.0 VDC (CCU-TX7P) (burst), 75 Ω
• Very damp or dusty places. Power consumption SDI 2) BNC type (2)
• Where rain is likely to reach the unit. Care 95 W SDI format, 270 Mbps, SMPTE
• Places subject to severe vibration. If the body of the unit is dirty, wipe it with a dry cloth. Cable length 1500 m max. (diameter: 14.5 mm ) 259M (CCU-TX7)/CCIR656-III
• Near strong magnetic fields For severe dirt, use a soft cloth steeped in a small Operating temperature (CCU-TX7P)
• Near transmitting stations generating strong radio amount of neutral detergent, then wipe dry. Do not SYNC BNC type (1)
5°C to 40°C (41°F to 104°F)
waves. use volatile solvents such as alcohol or thinners, as
Mass About 8.45 kg (18 lb 10 oz) 0.3 Vp-p, 75 Ω, negative polarity
these may damage the finish.
Dimensions (w/h/d, excluding protruding parts)
Avoid violent impacts 200 × 164 × 370 mm (7 7/8 × 6 1/2 ×
Dropping the unit, or otherwise imparting a violent Camera control input/output connectors
14 5/8 inches)
shock to it, is likely to cause it to malfunction.
CAMERA Triaxial (1)
Input connectors COAX BNC type (1)
REMOTE 10-pin (1)
GENLOCK BNC type (2, loop-through) INTERCOM/TALLY
VBS/BS, 1.0Vp-p, 75 Ω D-sub 25-pin (1)
RETURN VIDEO 1, 2 4W/2W
BNC type (2 each, loop-through) TALLY: 24 VDC, TTL level or
VBS, 1.0 Vp-p, 75 Ω contact signals switchable
PROMPT VIDEO BNC type (2, loop-through) RTS XLR 3-pin (2)
VBS, 1.0 Vp-p, 75 Ω RS232C D-sub 25-pin (2)
PGM IN XLR 3-pin (1) INTERCOM(on the front panel)
XLR 5-pin (1)
Output connectors
Accessories supplied
VBS1, VBS2 BNC type (1 each)
VBS, 1.0 Vp-p, 75 Ω AC power cord (1)
Y/R–Y/B–Y1) BNC type (2 each) Power cord plug retainer (1)
Y: 1.0 Vp-p, 75 Ω Number plates (1 set)
R–Y/B–Y: 700 mVp-p (CCU- Operation Manual (1)
TX7)/525 mVp-p (CCU-TX7P),
75 Ω
Optional accessories
R/G/B1) BNC type (2 each)
700 mVp-p, 75 Ω
COU-TX7 Camera Operation Unit
PIX BNC type (1), 1.0 Vp-p, 75 Ω
DXBK-701 SDI Output Board
WF BNC type (1)
RCP-TX7 Remote Control Panel
700 mVp-p, 75 Ω
RMM-TXC7 Rack Mount Bracket
Encoded output: 1.0 Vp-p, 75 Ω
WF MODE 4-pin (1)
Design and specifications are subject to change
without notice.
..........................................................................................................................................................................................................
English 13 12 11 10 9 8 7 6 5 4 3 2 1
CCU-TX7/TX7P
25 24 23 22 21 20 19 18 17 16 15 14
Pin assignment of the INTERCOM/TALLY
connector
No. Signal name Specifications
English The pin assignment for the unit’s INTERCOM/
1 GREEN TALLY (Y) IN ON: 24V DC/TTL(H)/Short
TALLY connector (D-sub 25-pin) is as follows.
14 GREEN TALLY (X) IN OFF: 0V DC/TTL(L)/Open
To switch the DXC-D30WS/D30WSP
aspect ratio 2 RED TALLY (Y) IN ON: 24V DC/TTL(H)/Short
15 RED TALLY (X) IN OFF: 0V DC/TTL(L)/Open
To switch the DXC-D30WS/D30WSP Digital Video 3 GND Ground for intercom remote
Camera connected to this unit via the CA-TX7/TX7P signal
Camera Adaptor between 16:9 and 4:3 aspect ratios, 16 CAM MIC OFF IN L: Camera intercom off
use the following methods. 4 CH2 INT IN L: Channel-2 interrupt on
17 CH1 INT IN L: Channel-1 interrupt on
When using the RCP-TX7 Remote Control
5 4W CH2 (R) (G) OUT 4-wire channel-2 system receive,
Panel
18 4W CH2 (R) (Y) OUT 0 dBu balanced
Switch the aspect ratio using advanced setting page
9/11 of the RCP-TX7’s OTHERS menu. 6 4W CH2 (R) (X) OUT
19 4W CH2 (T) (G) IN 4-wire channel-2 system talk,
When using the COU-TX7 Camera Operation 7 4W CH2 (T) (Y) IN 0 dBu balanced
3-864-243-01(1)
CCU-TX7 (E)/V1
CCU-TX7 (E)/V1
1-2. DXBK-701
3-866-203-01(1)
DXBK-701
1998 by Sony Corporation
1-13
1-14
English
11
CCU-TX7 (E)/V1
FREE LOCK
FREE LOCK
ADJ OPE
ADJ OPE
4ch 2ch
AUDIO MODE
4 Remove the two cables temporarily fixed to the CCU-TX7/
TX7P power supply unit from the clamp, and connect to
the two SDI output connectors on the board. It does not
matter which cable is connected to which connector.
Cables
(Continued)
CCU-TX7 (E)/V1
Board retainer
14 15
CCU-TX7 (E)/V1
5 Push the board fully in, and refasten the board retainer,
Auto Level Adjustment
using the two screws removed in step 2.
The auto level adjustment is necessary to ensure that the video
levels are appropriate. Carry out auto level adjustment in step 6
(page 16) of the procedure under “Fitting and Adjustment”.
Board retainer After a few seconds, when the AUTO LEVEL indicator
lights in green the auto level adjustment is completed.
7 Power on the CCU-TX7/TX7P, and carry out auto level • If the indicator lights in red, check the switch setting on the
board. (See step 1 on page 14.) If the indicator flashes, check
adjustment. (See page 17.)
that color bars are being displayed.
• The adjustment values are stored on this board, so
8 Close the front panel of the CCU-TX7/TX7P, and fasten readjustment is not normally required.
the screws. However, if the CCU-TX7/TX7P is not used for a long time
(several months), or if the board is installed in a different
CCU-TX7/TX7P, the auto level adjustment must be made
again.
For details of the operating procedures for other devices, refer to the
operating instructions supplied with each device.
1-17
16 17
1-18
Specifications
Power consumption 4.5 W
Operating temperature 5°C to 40°C (41°F to 104°F)
Mass 330 g (11 oz)
Dimensions 17 × 148 × 277 mm (11/16 × 5 7/8 × 11
inches) (w/h/d, excluding
projections)
Output signal SDI output connectors
SDI format (270 Mbps)
SMPTE 259M (CCU-TX7)/
CCIR 656-III (CCU-TX7P)
CCU-TX7 (E)/V1
18
SECTION 2
INSTALLATION
2-1. CONNECTORS AND CABLES . MIC OUTPUT CH1/CH2 (XLR 3P, MALE)
. PROMPT VIDEO (BNC) : VBS, 1.0 V p-p 3 MIC OUT (X) board)
. SPARE (BNC) *1 : RM Video Input
VBS, 1.0 V p-p
. WF MODE (4P, FEMALE)
[Output signals]
. R (BNC) *2 : 700 mV p-p 4 1
3 2
. G (BNC) *2 : 700 mV p-p
. B (BNC) *2 : 700 mV p-p (EXTERNAL VIEW)
. Y (BNC) *2 : 1.0 V p-p
. R-Y (BNC) *2 : 700 mV p-p (for CCU-TX7) (0 dBu = 0.775 Vrms)
: 525 mV p-p (for CCU-TX7P)
No. Signal Specifications
. B-Y (BNC) *2 : 700 mV p-p (for CCU-TX7)
1 SEQ CONT OUT (G) OPEN COLLECTOR
: 525 mV p-p (for CCU-TX7P)
. C (BNC) *2 : 286 mV p-p (burst) 2 SEQ CONT OUT (X)
(for CCU-TX7) 3 STAIR CASE OUT (X) ∗1)
: 300 mV p-p (for CCU-TX7P) 4 STAIR CASE OUT (G) GND for STAIR CASE
. PIX (BNC) : 1.0 V p-p ∗1) Stair Case signal
. VBS 1/2 (BNC) : 140 IRE
. SYNC (BNC) : VBS, 0.3 V p-p, negative
. WF (BNC) : 700 mV p-p
(Encoded output : 1.0 V p-p) 10 ±2 V
R G B
DC0 ±2 V
. SDI OUT (BNC) : 800 mV p-p
[Input/Output signals]
. TRIAX : King type (for CCU-TX7)
Fischer type (for CCU-TX7P)
. COAX (BNC)
13 1 13 1
25 14 25 14
1 GREEN TALLY (Y) IN ON : 24 V DC/TTL (H)/SHORT 1 CHASSHIS GND This is based on RS-232C
14 GREEN TALLY (X) IN OFF : 0 V DC/TTL (L)/OPEN 2 TXDATA specification.
2 RED TALLY (Y) IN ON : 24 V DC/TTL (H)/SHORT 3 RXDATA 38,400 bps or 9600 bps Switchable
15 RED TALLY (X) IN OFF : 0 V DC/TTL (L)/OPEN by the internal switch on the
CCU-TX7 (E)/V1
2-2
. PGM IN (XLR 3P, FEMALE) 2. Front panel
(EXTERNAL VIEW)
(EXTERNAL VIEW)
No. Signal Specifications
. RTS IN/OUT (XLR 3P, FEMALE ↔ MALE) 3 NCOM (R) (G) OUT GND for HEADPHONE
4 INCOM (R) (X) OUT _0 dBu (Max. 18 dBu)
FEMALE MALE
5 PGM (X) OUT
Loop-through
(EXTERNAL VIEW)
Use the connectors below or the equivalent at its tip when . CCA-7 cable
cables are connected to each connector on the connector
panel during installation and servicing. Blue
White
Connector name Connected connector/cable
Orange
GENLOCK VIDEO 1, 2 1-560-069-11 plug,
RETURN VIDEO BNC, or B-B cable assembly Black
PROMPT VIDEO (1.5 m in cable length, optional) Green
R/R-Y/C 1, 2
G/Y/Y 1 8 1 8 1
B/B-Y 1, 2 7
9 10
2 7
9 10
2
WF
PIX 6 3 6 3
VBS 1/2 5 4 5 4
SYNC White
COAX Brown
(BNC type)
White
MIC CH1/CH2 1-508-083-00 XLR, 3-pin
RTS FEMALE or Red
(3P, MALE) CANNON XLR-3-11C Yellow
or the equivalent
PGM IN 1-508-084-00 XLR, 3-pin
RTS MALE or
CANNON XLR-3-12C 2-2. MAKING OF WF MODE
or the equivalent
CONNECTOR
INTERCOM/TALLY D-Sub, 25-pin male,
RS-232C CH1/CH2 JAE DA-25PF-N or the equivalent
(25P, FEMALE) . When connecting plug to wave form monitor, make the
plug as follow.
WF MODE 1-560-343-11 plug, 4-pin male
(4P, FEMALE)
REMOTE 1-766-848-11 plug, 10-pin male, or PLUG (4P) (Sony part No. 1-560-343-11)
(10P, FEMALE) CCA cable assembly
CCA-7-5 (supplied with RCP-TX7)
(50 m max.) To wave form monitor
4 1
INTERCOM 1-508-370-11 XLR, 5-pin male, 3 2 (REMOTE)
(5P, FEMALE) or CANNON XLR-5-12-C or the
equivalent (EXTERNAL VIEW)
GROUND
4 1
3 2
(WIRING SIDE)
STAIR CASE
SEQ CONT
CCU-TX7 (E)/V1
2-4
2-3. COAX CONNECTOR 2-4. OPERATING ENVIRONMENT
The COAX connector (BNC type) can be used for connection Operating temperature : +5 dC to +40 dC
between the CCU and the CA with a BNC cable instead of a Storage temperature : _20 dC to +55 dC
triaxial cable. In this case, supply the power source from Humidity : Noncondcnsing
outside to the CA side. Supply voltage : 100 V to 240 V ± 10% (50/60 Hz)
And for the CA side, it is needed to modify the TRIAX Power consumption : 95 W (maximum)
harness to the COAX harness.
For the CCU, the following modification is required. 1. Do not put the unit in a place subject to high temperature
Disconnect the RF cable from the CN3 on the IO-141 board or in a location near hear sources.
and reconnect it to the CN4. 2. Do not put the unit in a place subject to excessive
electrical and magnetic fields.
3. Put the unit in a dry and well-ventilated place.
RF cable
4. Do not put the unit in a place subject to excessive dust
and mechanical shock.
IO-140 board 5. Do not put the unit in a place subject to direct sunlight
and light.
CN3
CN4 300
169
164
8 200 9.5
217.5
(Unit: mm)
Mounting
RMM-TXC7
B5 screws
(60 mm or more long)
Screws
Screws
CCU-TX7 (E)/V1
2-6
2-6. SWITCH FUNCTIONS ON BOARD . S2002 (PROMPT SELECT TX/RX)
TX : When selecting the TX mode, the CCU modulates
CT-181 board the VBS signal input to the PROMPT VIDEO IN
connector on the CCU-TX7/TX7P, and modulated
E1001
signal is sent to the CA-TX7/TX7P.
TP2006 RET FREQ
CV1
RX : When selecting the RX mode, the CA modulates
CT-181 R TALLY S2011
R TALLY
CONTACT
POWER
CONTACT
POWER
TP1000 the VBS signal input to the PROMPT VIDEO IN
TP21
E12
connector on the CA-TX7/TX7P, and modulated
TP1002
DC24V RF AGC DLY
DC24V S2013 RV22
TTL E1000
TTL R TALLY
G TALLY
CONTACT CONTACT
S2012
PROMPT FREQ signal is sent to the CCU-TX7/TX7P.
LV2
POWER G TALLY
DC24V
POWER
DC24V
S2014
RV23
PROMPT LEVEL PROMPT TUNE
Note : When using this switch, change as follows.
TTL
G TALLY
MIC GAIN
TTL
MIC 1 GAIN LV3 E13 TP22
. In case of using the TX mode (TX side) ;
NORM
MIN
CH-1 SW1000 S2002
TP23
1) Disconnect CN8 and connect CN3 and CN7
MAX
SW1001 PROMPT CN7
NORM
CH-2
MIC 2 GAIN
MIN
S1001 RX TX
MAX S1004 CN8
PANEL RS232C-2 PROMPT RF RX
on the CT-181 board.
LOCAL REMOTE
SELECT
PANEL IF BOARD
S1000
REMOTE TP1001
LOCAL TP2001
T201
TP8
RV201
MIC 1
LEV
TP10
RV301
TP11
T301
MIC 2
E12
LEV
AA-90 TP9
PGM IN TP44
TP13
S2081
TP12
PGM IN
0dB
TP14
T401
RV401
—20dB E10
TP15
MIC-1-LEV
MIC 1 LEVEL
INCOM
LEV
S201
0dB
—20dB TP43
LV101
RV101
TONE TUNE 5.6M TUNE
E2 TP6
MIC 2 LEVEL
MIC-2-LEV
S301
0dB
—20dB TP7
INCOM MODE
TP3
TP5
MIC TEST
MIC TEST
LV21
1CH
S2004
CH-1
S2003
CH-2
2.5M CCU DATA LV61 LV41
OHM
4.3M 3.6M
OFF E11
TP2
LEVEL IND
2CH
E1
REV
TP1
TP46
RTS/CLEAR-COM INCOM SELECT
RV81
INCOM
DEV
2W
S2005 S2002
(
CLEAR
COM ) RTS
4W TP3005
RTS
TP3002
CLEAR
COM E3001
TP3001
TP3004
RV2000
SIDE TONE
TP3003
. S2005 (RTS/Clear-Com)
This switch selects RTS or Clear-Com position when the S2002 switch is set to RTS position.
Factory setting : RTS
Set the S2002, S2003, S2005 and S2007 switches to the positions shown in the table below, according to the intercom system.
X : Don’t care
CCU-TX7 (E)/V1
2-8
. S201 (MIC 1 LEVEL)
This switch sets the audio signal level of the MIC OUTPUT
CH-1 connector on the CCU rear panel to 0 dBu or _20 dBu.
Factory setting : 0 dBu
Y CARR BAL
TP2 Y OFFSET ADJ
RV8 TP11
TP5
RV24
TP8 Y LEVEL
YD-26 RV9
TP4 TP7 RV6
Y 2'nd AGC
Y CAR LEVEL
Y RF TUNE VCO DC SET
S3 E6
RV2 RV5 TP6
OFF
TP9 RV17
ON
TP12
RV7
LV1 BLACK S/H SYNC S/H R-Y LEVEL
TP3 TP17
S4 RV12
C 2'nd AGC B-Y LEVEL
E8
E7 E9
TP18
R-Y CARR BAL TP19
OFF
ON
B-Y CARR BAL RV16
TP13 TP14 RV11 TP18
TP15
RV10
C AGC CONT RV18
90° SET
RV13 RV14 RV15
OFFSET ADJ PLL SET C CAR LEV
E16
TP1 E4
S2
E3 CABLE LENGTH TP21 TP20
S1
MODE
MAN
AUTO
0 100 m
1 300 m
2 500 m
3 700 m
4 NOT IN USED
CCU-TX7 (E)/V1
2-10
ES-20 board
Y LEVEL (VBS)
VBS LEVEL
RV813
SYNC LEVEL (VBS) RV804
RV1
CAM H PHASE
PHASE RV2 Y LEVEL(COMP)
RV806
BURST
LEVEL
H RV7 H PHASE RV800 RV801
SYNC PHASE
TP17 TP15
Y SETUP LEVEL SYNC LEVEL(COMP)
Q(U)CAL
RV809
(NTSC ONLY)
SC RV6 SC PHASE
RV808
(U)LEV
RV805
I(V)CAL
RV4 TP1
SC 0/180
0
SC FREQUENCY
RV807
BURST
PHASE
S3
180°
RV812
RV811
R-Y LEVEL
RV5 B-Y LEVEL
OUT PUT 1
OUTPUT 1
SC-H PHASE
SELECT
R/G/B
S800
Y/R-Y/B-Y
Y/C
E1
S2
OUT PUT 2
S1000
R/G/B G MAT BAL2 B WHT BAL R WHT BAL
Y/R-Y/B-Y S1 RV506 RV505 RV500
Y CLP LEVEL
Y/C
RV515
SEQ ON
TP501
S4
OUTPUT 2
S801
SELECT
RV508
TP507
TP506
TP505
RV1001
RV507 TP7
G MAT BAL1
G LEVEL TP502 R-Y BLK BAL TP5
R MAT BAL RV501 POSITION TP4
RV511 RV509 TP2
R DC BAL TP503 R-Y GAIN ADJ
RV510 R LEVEL TP3
RV502
E16
B MAT BAL
RV514 RV512 RV1000
RV504 RV503 LEVEL
B DC BAL RV513 B LEVEL B-Y GAIN ADJ B-Y BLK BAL
RV1
S4
DU-33 Board (A SIDE)
CALL
PRI
Set this switch to ON position when the 16:9 compatible S1 S3 VATE
OFF CH2
ON
camera is connected and used in the 16:9 mode. S2 RV1 RV2
S5
CARBON DINAMIC
CN1
AU-234 Board (A SIDE)
. S5 (DYNAMIC/CARBON)
Set this switch according to the type of the headset
microphone connected to the INTERCOM connector on
the front panel.
DYNAMIC : Dynamic type microphone
CARBON : Carbon type microphone
Factory setting : DYNAMIC
CCU-TX7 (E)/V1
2-12
SDI-44 board
TP807
TP806
TP805
TP101 E101
TP810
SDI-44 RV1401 RV1400
ALARM
B-Y DC B-Y LEVEL
TP1400
D201
S701
LOCK FREE
RV1501 RV1500
RV701 R-Y DC R-Y LEVEL
TP1500
TP702
CN2 S601
OPE ADJ TP1201 E201
AUTO LEVEL
D601
(BARS)
AUTO LEVEL
S602
E1001
SDI POWER
AUTO IND
S201
ON
OFF RV904
RV903
TP902
RV901
TP901 RV902
. S601 (ADJ/OPE)
This switch is used for returning the level control values of
the R-Y and B-Y video signals to the factory setting.
Set this switch to ADJ position and turn on the power to
the main unit.
Alternatively, set this switch to ADJ position and press the
AUTOLEVEL (BARS) switch.
Usually, set this switch to OPE position.
Factory setting : OPE
Front panel
CN-1328 board
CN-1350 board
SW-892
board
Switching regulator (COU-TX7)
AU-234 board
Loosen
two coin
screws
2.
Connector
Connector
AU-234 board
Front panel
CCU-TX7(E)/V1 3-1
(2) Removal of Cover 3-2-2. Replacement of Switching Regulator
Connector (CN10)
IO-140 board
B 3x5
K 3x6
Bottom cover
B 3x5
Connector (CN19)
Rearpanel Connector (CN20)
K 3x6
B 4x5
B 4x5
B 4x5
Switching regulator
CCU-TX7(E)/V1
3-2
[For the Serial No. 11001 and Higher (UC)] 3-2-3. Replacement of Fan
[For the Serial No. 41001 and Higher (CE)]
[For the Serial No. 11001 and Higher (UC)]
1. Remove the top cover. (Refer to “3-2-1. Removal of [For the Serial No. 41001 and Higher (CE)]
Cabinet”.)
2. Remove four screws (K3x6) and disconnect CN1 on the n
IO-140 board and CN10, CN19, CN20 and CN28 on the . When the fan is out of order, the CAMERA POWER
MB-693A board. Remove the rear panel. indicator is blinking.
3. Remove four screws (PSW3x20) and remove the fan. Turn off the power immediately and replace the fan.
Using the defective fan may reduce the service life of the
equipment extremely.
Fan . Before replacing the fan, be sure to turn off the power
switch and unplug the power cord.
PSW 3x20
A 1. Perform steps 1 to 3 in Section “3-2-2. Replacement of
Connector (CN10) Switching Regulator” for the Serial No. 11001 and
Connector (CN1) higher (UC), Serial No. 41001 and higher to remove the
fan.
IO-140 board
2. Install a new fan in the reverse order.
MB-693A board
Connector
(CN28)
Connector (CN19)
Rearpanel
K 3x6 Connector (CN20)
B 4x5
B 4x5
B 4x5
Switching regulator
CCU-TX7(E)/V1
3-4
3-4. EXTENSION OF DXBK-701
(SDI-44 BOARD)
Preparation:
1 Coaxial connector converter : Sony part No. 1-750-881-11
2 Coaxial cable assembly : Sony part No. 1-765-112-12
3 BNC cable : BELDEN 8281 cable or
equivalent
Coaxial cables
SDI-44 board
EX-564 board
2 Coaxial cable
assembly
1 Coaxial
connector
converter
3 BNC cable
Equipment,
Monitor
CCU-TX7(E)/V1 3-5
SECTION 4
ADJUSTMENT
75Z
RCP-TX7
Audio connections
Fig-1 Fig-2
CCU-TX7 (E)/V1
4-2
4-2. Video Signal System Adjustment 4-2-2. CAM H Phase Adjustment
CH2
50%
Y LEVEL (VBS)
VBS LEVEL
RV813
(NTSC ONLY)
SC RV6 SC PHASE
RV808
(U)LEV
RV805
I(V)CAL
RV4 TP1
SC 0/180
0
SC FREQUENCY
RV807
BURST
PHASE
S3
180°
RV812
RV811
R-Y LEVEL
SC-H PHASE
SELECT
R/G/B
S800
Y/R-Y/B-Y
Y/C
E1
S2
OUT PUT 2
S1000
Y/C
RV515
SEQ ON
TP501
S4
OUTPUT 2
S801
SELECT
RV508
TP507
TP506
TP505
RV1001
RV507 TP7
G MAT BAL1
G LEVEL TP502 R-Y BLK BAL TP5
R MAT BAL RV501 POSITION TP4
RV511 RV509 TP2
R DC BAL TP503 R-Y GAIN ADJ
RV510 R LEVEL TP3
RV502
E16
B MAT BAL
RV514 RV512 RV1000
RV504 RV503 LEVEL
B DC BAL RV513 B LEVEL B-Y GAIN ADJ B-Y BLK BAL
T1 T2 T1 T2
CCU-TX7 (E)/V1
4-4
4-2-5. INT SC Phase Adjustment 4-2-6. Y CLAMP Adjustment
Adjustment Procedure :
. Adujst 1RV5 (SC-H PHASE)/ES-20 board so that the
luminance line of BURST (SC) is the same as following
figure.
B yl B
G Cy G Cy mg
Y LEVEL (VBS)
VBS LEVEL
RV813
(NTSC ONLY)
SC RV6 SC PHASE
RV808
(U)LEV
RV805
I(V)CAL
RV4 TP1
SC 0/180
0
SC FREQUENCY
RV807
BURST
PHASE
S3
180°
RV812
RV811
R-Y LEVEL
SC-H PHASE
SELECT
R/G/B
S800
Y/R-Y/B-Y
Y/C
E1
S2
OUT PUT 2
S1000
Y/C
RV515
SEQ ON
TP501
S4
OUTPUT 2
S801
SELECT
RV508
TP507
TP506
TP505
RV1001
RV507 TP7
G MAT BAL1
G LEVEL TP502 R-Y BLK BAL TP5
R MAT BAL RV501 POSITION TP4
RV511 RV509 TP2
R DC BAL TP503 R-Y GAIN ADJ
RV510 R LEVEL TP3
RV502
E16
B MAT BAL
RV514 RV512 RV1000
RV504 RV503 LEVEL
B DC BAL RV513 B LEVEL B-Y GAIN ADJ B-Y BLK BAL
A A
B B
B B
C
Y LEVEL (VBS)
VBS LEVEL
RV813
(NTSC ONLY)
SC RV6 SC PHASE
RV808
(U)LEV
RV805
I(V)CAL
RV4 TP1
SC 0/180
0
SC FREQUENCY
RV807
BURST
PHASE
S3
180°
RV812
RV811
R-Y LEVEL
SC-H PHASE
SELECT
R/G/B
S800
Y/R-Y/B-Y
Y/C
E1
S2
OUT PUT 2
S1000
Y/C
RV515
SEQ ON
TP501
S4
OUTPUT 2
S801
SELECT
RV508
TP507
TP506
TP505
RV1001
RV507 TP7
G MAT BAL1
G LEVEL TP502 R-Y BLK BAL TP5
R MAT BAL RV501 POSITION TP4
RV511 RV509 TP2
R DC BAL TP503 R-Y GAIN ADJ
RV510 R LEVEL TP3
RV502
E16
B MAT BAL
RV514 RV512 RV1000
RV504 RV503 LEVEL
B DC BAL RV513 B LEVEL B-Y GAIN ADJ B-Y BLK BAL
CA RV507
E RV506
BA
DB
C C
F
A A A A
2. Adjusting point : 1RV510 (R LEVEL)/ES-20 board 2. Adjusting point : 1RV513 (B LEVEL)/ES-20 board
Specification : B = 700 ± 10 mV [ For NTSC] Specification : B = 700 ± 10 mV [For NTSC]
B = 700 ± 10 mV [ For PAL] B = 700 ± 10 mV [For PAL]
B B
B
B
Y LEVEL (VBS)
VBS LEVEL
RV813
(NTSC ONLY)
SC RV6 SC PHASE
RV808
(U)LEV
RV805
I(V)CAL
RV4 TP1
SC 0/180
0
SC FREQUENCY
RV807
BURST
PHASE
S3
180°
RV812
RV811
R-Y LEVEL
SC-H PHASE
SELECT
R/G/B
S800
Y/R-Y/B-Y
Y/C
E1
S2
OUT PUT 2
S1000
Y/C
RV515
SEQ ON
TP501
S4
OUTPUT 2
S801
SELECT
RV508
TP507
TP506
TP505
RV1001
RV507 TP7
G MAT BAL1
G LEVEL TP502 R-Y BLK BAL TP5
R MAT BAL RV501 POSITION TP4
RV511 RV509 TP2
R DC BAL TP503 R-Y GAIN ADJ
RV510 R LEVEL TP3
RV502
E16
B MAT BAL
RV514 RV512 RV1000
RV504 RV503 LEVEL
B DC BAL RV513 B LEVEL B-Y GAIN ADJ B-Y BLK BAL
R g R
MG MG
75% V
100%
YL YL b
U
B yl B
G Cy G Cy mg
G R-Y OUT
Cy G Cy mg B-Y OUT
r
A B
3. Repeat procedure 1 and 2 several times.
CCU-TX7 (E)/V1
4-10
4-2-17. VBS OUT Level Adjustment 4-2-18. STAIR CASE Adjustment
Equipment : Waveform monitor Note : This adjustment is for temporary adjustment when
To be extended : ES-20 board repairing the STAIR CASE block. In the system
Preparation : set up, the readjustment is required to match the
. Select the BARS mode on the RCP-TX7 or COU-TX7. characteristic of waveform monitor.
Test point : VBS 1 OUT connector/CCU rear panel
Adjusting point : 1RV813 (VBS LEVEL)/ES-20 board Equipment : Oscilloscope
Specification : A = 100 ± 1 IRE [For NTSC] To be extended : ES-20 board
A = 700 ± 10 mV [For PAL] Preparation :
. Select the BARS mode on the RCP-TX7.
[For NTSC] [For PAL]
. MONITOR SELECT button/RCP-TX7 → "SEQ"
Test point : pin 76 (GND: pin 75)/
A A extension board
Adjusting point : 1RV1001/ES-20 board
1RV1000/ES-20 board
Specification : A = 10.0 ± 1 V p-p (1RV1001)
B = 0 ± 1 V dc (1RV1000)
B
A GND
Y LEVEL (VBS)
VBS LEVEL
RV813
PHASE RV2
RV806
BURST
LEVEL
(NTSC ONLY)
SC RV6 SC PHASE
RV808
(U)LEV
RV805
I(V)CAL
RV4 TP1
SC 0/180
0
SC FREQUENCY
RV807
BURST
PHASE
S3
180°
RV812
RV811
R-Y LEVEL
SC-H PHASE
SELECT
R/G/B
S800
Y/R-Y/B-Y
Y/C
E1
S2
OUT PUT 2
S1000
Y/C
RV515
SEQ ON
TP501
S4
OUTPUT 2
S801
SELECT
RV508
TP507
TP506
TP505
RV1001
RV507 TP7
G MAT BAL1
G LEVEL TP502 R-Y BLK BAL TP5
R MAT BAL RV501 POSITION TP4
RV511 RV509 TP2
R DC BAL TP503 R-Y GAIN ADJ
RV510 R LEVEL TP3
RV502
E16
B MAT BAL
RV514 RV512 RV1000
RV504 RV503 LEVEL
B DC BAL RV513 B LEVEL B-Y GAIN ADJ B-Y BLK BAL
OFF ON
CN1
S1
RV1
50%
A
H T
TP26 E5
SAMPL GATE
E1 SAMPL S/H RV3 TP10
RV1
Y AGC CONT E2 RV4
Y CARR BAL
TP8 Y LEVEL
YD-26 RV9
TP4 TP7 RV6
Y 2'nd AGC
Y CAR LEVEL
TP9 RV17
ON
TP12
RV7
ON
RV10
C AGC CONT RV18
90° SET
RV13 RV14 RV15
OFFSET ADJ PLL SET C CAR LEV
E16
TP1 E4
S2
E3 CABLE LENGTH TP21 TP20
S1
MODE
MAN
AUTO
50%
A
GND
T
CCU-TX7 (E)/V1
4-14
4-3-5. Sample Pulse Width Adjustment 4-3-6. Sample Pulse V Gate Width
Adjustment
Equipment : Oscilloscope
To be extended : YD-26 board Equipment : Oscilloscope
Test point : TP7 (GND: E2)/YD-26 board To be extended : YD-26 board
Adjusting point : 1RV4 (SAMPLE S/H)/YD-26 board Test point : TP7 (GND: E2)/YD-26 board
Specification : T = 40.0 ± 2.0 µs Adjusting point : 1RV3 (SAMPLE GATE)/YD-26 board
Adjustment Procedure :
. Confirm that the sample pulses have six pulses in both odd
and even fields.
If not met, adjust 1RV3 (SAMPLE GATE)/YD-26 board
so that the sample pulses have six pulses in both odd and
even fields.
V 6 Pulses
50%
TP26 E5
SAMPL GATE
E1 SAMPL S/H RV3 TP10
RV1
Y AGC CONT E2 RV4
Y CARR BAL
TP8 Y LEVEL
YD-26 RV9
TP4 TP7 RV6
Y 2'nd AGC
Y CAR LEVEL
TP9 RV17
ON
TP12
RV7
ON
RV10
C AGC CONT RV18
90° SET
RV13 RV14 RV15
OFFSET ADJ PLL SET C CAR LEV
E16
TP1 E4
S2
E3 CABLE LENGTH TP21 TP20
S1
MODE
MAN
AUTO
CCU-TX7 (E)/V1
4-16
4-3-9. Y OFFSET Adjustment 4-3-11. Y 1st AGC Adjustment
A
BLKG
SYNC
Equipment : Oscilloscope
To be extended : YD-26 board
Preparation :
. Select the BARS mode on the RCP-TX7 or COU-TX7.
Test point : TP26 (GND: E6)/YD-26 board
Adjusting point : 1FL3 (90˚ SIFT)/YD-26 board
Specification : A = 0 ± 10 mV
A A
TP26 E5
SAMPL GATE
E1 SAMPL S/H RV3 TP10
RV1
Y AGC CONT E2 RV4
Y CARR BAL
TP8 Y LEVEL
YD-26 RV9
TP4 TP7 RV6
Y 2'nd AGC
Y CAR LEVEL
TP9 RV17
ON
TP12
RV7
ON
RV10
C AGC CONT RV18
90° SET
RV13 RV14 RV15
OFFSET ADJ PLL SET C CAR LEV
E16
TP1 E4
S2
E3 CABLE LENGTH TP21 TP20
S1
MODE
MAN
AUTO
A
GND
Maximum
TP26 E5
SAMPL GATE
E1 SAMPL S/H RV3 TP10
RV1
Y AGC CONT E2 RV4
Y CARR BAL
TP8 Y LEVEL
YD-26 RV9
TP4 TP7 RV6
Y 2'nd AGC
Y CAR LEVEL
TP9 RV17
ON
TP12
RV7
ON
RV10
C AGC CONT RV18
90° SET
RV13 RV14 RV15
OFFSET ADJ PLL SET C CAR LEV
E16
TP1 E4
S2
E3 CABLE LENGTH TP21 TP20
S1
MODE
MAN
AUTO
Note : Make sure that 45 MHz frequency on the YM-15 Equipment : Oscilloscope
board (CA-TX7/TX7P) is correct. To be extended : YD-26 board
Preparation :
Equipment : Oscilloscope . S1 (AUTO/MANU)/YD-26 board → "AUTO"
To be extended : YD-26 board . S4 (C 2nd AGC)/YD-26 board → "OFF"
Test point : TP17 (GND: E8)/YD-26 board Test point : TP17 (GND: E8)/YD-26 board
Adjusting point : 1RV13 (OFFSET ADJ)/YD-26 board Adjusting point : 1RV10 (C AGC CONT)/YD-26 board
Specification : A = 0 ± 3 mV Specification : A = 350 ± 20 mV
BLKG
SYNC
CCU-TX7 (E)/V1
4-20
4-4-6. B-Y OUT Level Adjustment 4-4-7. R-Y DEMOD Carrier Balance
Adjustment
Equipment : Oscilloscope
To be extended : YD-26 board Equipment : Oscilloscope
Preparation : To be extended : YD-26 board
. S4 (C 2nd AGC)/YD-26 board → "ON" Test point : TP18 (GND: E9)/YD-26 board
Test point : TP17 (GND: E8)/YD-26 board Adjusting point : 1RV16 (R-Y CARR BAL)/
Adjusting point : 1RV12 (B-Y LEVEL)/YD-26 board YD-26 board
Specification : A = 350 ± 5 mV p-p Specification : Adjust 1RV16 so that the negative DC
level is maximum.
GND
A
Maximum
(Negative DC level) _
TP26 E5
SAMPL GATE
E1 SAMPL S/H RV3 TP10
RV1
Y AGC CONT E2 RV4
Y CARR BAL
TP8 Y LEVEL
YD-26 RV9
TP4 TP7 RV6
Y 2'nd AGC
Y CAR LEVEL
TP9 RV17
ON
TP12
RV7
ON
RV10
C AGC CONT RV18
90° SET
RV13 RV14 RV15
OFFSET ADJ PLL SET C CAR LEV
E16
TP1 E4
S2
E3 CABLE LENGTH TP21 TP20
S1
MODE
MAN
AUTO
Note : Make sure that 45 MHz frequency on the YM-15 Equipment : Oscilloscope
board (CA-TX7/TX7P) is correct. To be extended : YD-26 board
Preparation :
Equipment : Oscilloscope . S4 (C 2nd AGC)/YD-26 board → "ON"
To be extended : YD-26 board Test point : TP19 (GND: E9)/YD-26 board
Test point : TP19 (GND: E9)/YD-26 board Adjusting point : 1RV17 (R-Y LEVEL)/YD-26 board
Adjusting point : 1RV18 (90° SET)/YD-26 board Specification : A = 350 ± 5 mV
Specification : The SAMPLE pulse level should be
minimum.
A = 0 ± 3 mV
A
CCU-TX7 (E)/V1
4-22
4-5. RETURN VIDEO Cable Compensation 4-5-2. Return Video Deviation Adjustment
System Adjustment
Equipment : Spectrum analyzer
4-5-1. Return Video Carrier Frequency To be extended : CT-181 board
Adjustment Preparation :
. Input 10 STEP signal (sub-carrier : OFF) of video signal
Equipment : Spectrum analyzer generator to RETURN-1 connector (75 Z termination, 1.0
To be extended : CT-181 board V p-p) on the CCU-TX7/TX7P rear panel.
Preparation : Test point : TP21 (GND: E12)/CT-181 board
. Input 10 STEP signal (sub-carrier : OFF) of video signal Adjusting point : 1RV20 (RET DEV)/CT-181 board
generator to RETURN-1 connector (75 Z termination, 1.0 Specification : T = 2.000 ± 0.005 MHz
V p-p) on the CCU-TX7/TX7P rear panel.
T
Test point : TP21 (GND: E12)/CT-181 board
Adjusting point : 1CV1 (RET FREQ)/CT-181 board
Specification : 69.000 ± 0.005 MHz
SYNC
69.0MHz
CENT FREQ: 69.0MHz
FFEQ SPAN: 5.0MHz
E1001
TP2006 RET FREQ
TP20
CV1
CONTACT CONTACT
POWER TP1000
POWER
TP21
E12
RET MIX
TP1002
RV19
POWER G TALLY
POWER RV23
DC24V PROMPT TUNE
DC24V PROMPT LEVEL
TTL
S2014
G TALLY
TTL CN2
MIC GAIN MIC 1 GAIN LV3 E13
SW1000 TP22 PROMPT RF TX RET RF
NORM
MIN
CH-1 S2002
TP23
MAX
SW1001 PROMPT CN7 CN3
NORM
CH-2
MIC 2 GAIN
MIN
S1001 RX TX PROMPT RF
MAX S1004 CN8
PANEL RS232C-2 PROMPT RF RX
LOCAL REMOTE
SELECT
PANEL IF BOARD
S1000
CCU-TX7 (E)/V1
4-24
4-6-2. RX PROMPT VIDEO Demod. 2. Adjust 1LV2 (PROMPT FREQ)/CT-181 board so that
Adjustment the frequency response at 6 MHz portion is minimum.
Note :
. Perform this adjustment only when replacing 1LV2
(PROMPT FREQ) or 1LV3 (PROMPT TUNE)/CT-181
board.
When performing this adjustment, the TRIX cable less than
300 m should be used. 6MHz
. Adjustment of CA-TX7/TX7P must be completed.
3. Change the output signal of the video signal generator to
Equipment : Waveform monitor, 10 STEP (sub-carrier : ON) signal.
Video signal generator (10 STEP signal) 4. Re-adjust 1LV3 (PROMPT TUNE)/CT-181 board so that
To be extended : CT-181 board the “A” portion at video waveform becomes flat.
Preparation : NOTE : If not met, Re-perform “4-6-2. RX PROMPT
. S1 (AUX/PROMPT)/YD-25 board (CA-TX7/TX7P) VIDEO Demod. Adjustment” after performing
→ "AUX" “4-6-3. RX PROMPT VIDEO RF AGC
. S6 (AUX/PROMPT)/YD-25 board (CA-TX7/TX7P) Adjustment”.
→ "AUX"
. Connect CN8 and CN3 on the CT-181board. (CCU-TX7/
TX7P)
. S2002 (TX ↔ RX)/CT-181 board (CCU-TX7/TX7P)
→ "RX"
. S1 (MODE AUTO/MAN)/YD-26 board (CCU-TX7/TX7P)
→ "AUTO"
. Input the SWEEP signal of the video signal generator to
PROMPTER OUT connector on the CA-TX7/TX7P rear
panel.
Test point : PROMPTER VIDEO IN connector
(CCU-TX7/TX7P rear panel)
Note : To measure the video level, make 75 Z
termination on the waveform monitor side. A
Adjusting point : 1LV2 (PROMPT FREQ)/
CT-181 board
1LV3 (PROMPT TUNE)/
CT-181 board flat
Adjustment Procedure :
1. Observe the waveform monitor screen and adjust 1LV3 Note : After the adjustment is completed, set the switches
(PROMPT TUNE)/CT-181 board so that the video as follows.
waveform is appeared. . S1 (AUX/PROMRT)/YD-25 board (CA-TX7/TX7P)
→ "PROMPT"
. S6 (AUX/PROMRT)/YD-25 board (CA-TX7/TX7P)
→ "PROMPT"
. Connect CN7 and CN3 on the CT-181board. (CCU-TX7/
TX7P)
. S2002 (TX ↔ RX) switch/CT-181 board (CCU-TX7/TX7P)
→ "TX"
Note : When performing this adjustment, the TRIAX cable Note : After this adjustment is completed, set the switches
50 m to 150 m should be used. as follows.
Adjustment of CA-TX7 /TX7P must be completed. . S1 (AUX/PROMPT)/YD-25 board (CA-TX7/TX7P)
→ "PROMPT"
Equipment : Oscilloscope, . S6 (AUX/PROMPT)/YD-25 board (CA-TX7/TX7P)
Video signal generator (10 STEP signal) → "PROMPT"
To be extended : CT-181 board . Connect CN7 and CN3 on the CT-181 board. (CCU-TX7/
Preparation : TX7P)
. S1 (AUX/PROMPT)/YD-25 board (CA-TX7/TX7P) . S2002 (TX ↔ RX)/CT-181 board (CCU-TX7/TX7P)
→ "AUX" → "TX"
. S6 (AUX/PROMPT)/YD-25 board (CA-TX7/TX7P)
→ "AUX"
. Connect CN8 and CN3 on the CT-181 board. (CCU-TX7/
TX7P)
. S2002 (TX ↔ RX)/CT-181 board (CCU-TX7/TX7P)
→ "RX"
. S1 (MODE AUTO/MAN)/YD-26 board (CCU-TX7/TX7P)
→ "AUTO"
. Input the 10 STEP (sub-carrier : ON) signal of the video
signal generator to PROMPTER connector on the CA-TX7/
TX7P rear panel.
Test point : PROMPTER VIDEO IN connector
(CCU-TX7/TX7P rear panel)
CN2
TP2000
RET MIX
PROMPT RF
PROMPT RF TX
Adjustment Procedure :
TP2003 TP2002 TP2004 TP2001
RV20
TP20 RET DIV
PROMPT RF RX
RET FREQ
CN8
TP22
TP23
TP1001
E13
E16
LV2
PROMPT
S2002
RF AGC DLY
RV22
LV3
TX
IF BOARD
RS232C-2
RX
PROMPT LEVEL
S1004
TP21
RV23
E12
E1001
TP1002
TP1000
E1000
S2013
S2012
S2014
S2011
TTL R TALLY
G TALLY
CONT MODE
TP2006
MIC 1 GAIN
MIC 2 GAIN
CONTACT
CONTACT
SW1000
SW1001
S1000
G TALLY
POWER
POWER
DC24V
SLAVE
NORM
DC24V
TTL
R TALLY
LOCAL REMOTE
S1002
SELECT
S1001
PANEL
CT-181
REMOTE
NORMAL
CONTROL MODE
CONTACT
CONTACT
POWER
POWER
LOCAL
DC24V
DC24V
SLAVE
CH-1
CH-2
MIC GAIN
G TALLY
R TALLY
PANEL
TTL
TTL
NORM
NORM
MAX
MAX
MIN
MIN
Note : When performing this adjustment, the TRIAX less 4-7-1. Frequency Set Adjustment
than 300 m should be used.
Adjustment of CA-TX7/TX7P must be completed. Note : Check to see that no signal is input to the INCOM
connector and PGM connector on the CCU-TX7/
Equipment : Oscilloscope, TX7P rear panel or the CCU-TX7/TX7P front panel.
Video signal generator (10 STEP signal) Perform the adjustment only when replacing the
To be extended : CT-181 board following part on AA-90 board.
Preparation : LV1, 21, 41, 81, D2, 22, 42, 62
. S1 (AUX/PROMPT)/YD-25 board (CA-TX7/TX7P)
→ "AUX" Equipment : Frequency counter, Digital voltmeter
. S6 (AUX/PROMPT)/YD-25 board (CA-TX7/TX7P) To be extended : AA-90 board
→ "AUX"
. Connect CN8 and CN3 on the CT-181 board. (CCU-TX7/ Adjustment Procedures :
TX7P) 1. Remove the ES-20 and CT-181 boards.
. S2002 (TX ↔ RX)/CT-181 board (CCU-TX7/TX7P) 2. Turn on the power switch "ON".
→ "RX" 3. AA-90 board (GND : E1)
. S1 (MODE AUTO/MAN)/YD-26 board (CCU TX7/TX7P)
Test point Adj. point Specifications
→ "AUTO"
. Input the 10 STEP signal (sub-carrier : ON) of the video PGM TP5 1LV81 4.300 ± 0.005 MHz
signal generator to PROMPTER OUT connector on the INCOM TP3 1LV41 3.600 ± 0.005 MHz
CA-TX7/TX7P real panel. H CONT TP1 1LV1 3.000 ± 0.005 MHz
Test point : PROMPTER VIDEO IN connector CCU DATA TP2 1LV21 2.500 ± 0.005 MHz
(CCU-TX7/TX7P rear panel)
Note : To measure the video level, make 75 Z Setting after Adjustment :
termination on the waveform monitor side. Install the ES-20 and CT-181 boards back into position.
Adjusting point : 1RV23 (PROMPT LEVEL)/CT-181
board.
A = 140 ± 6 IRE [For NTSC]
A = 1.00 ± 0.05 V [For PAL]
TP2001
PROMPT RF RX
CN7
CN8
TP22
PROMPT FREQ
TP23
TP1001
E13
TP2005
A
PROMPT TUNE
E16
LV2
PROMPT
S2002
RF AGC DLY
RV22
LV3
TX
IF BOARD
RS232C-2
RX
PROMPT LEVEL
S1004
TP21
RV23
E12
TP1002
as follows.
. S1 (AUX/PROMPT)/YD-25 board (CA-TX7/TX7P)
→ "PROMPT"
TP1000
E1000
S2012
S2014
S2011
→ "PROMPT"
TTL R TALLY
G TALLY
CONT MODE
TP2006
MIC 1 GAIN
MIC 2 GAIN
CONTACT
CONTACT
SW1000
SW1001
S1000
G TALLY
POWER
POWER
SLAVE
NORM
DC24V
TTL
R TALLY
LOCAL REMOTE
S1002
SELECT
S1001
PANEL
TX7P)
. S2002 (TX ↔ RX) /CT-181 board (CCU-TX-7/TX7P)
CT-181
REMOTE
NORMAL
CONTROL MODE
CONTACT
CONTACT
POWER
POWER
LOCAL
DC24V
DC24V
SLAVE
CH-1
CH-2
MIC GAIN
G TALLY
R TALLY
PANEL
TTL
TTL
→ "TX"
NORM
NORM
MAX
MAX
MIN
MIN
A B
T201
TP8
RV201
MIC 1
LEV
TP10
RV301
TP11
T301
MIC 2
E12
LEV
AA-90 TP9
PGM IN TP44
TP13
S2081
TP12
PGM IN
0dB
TP14
T401
RV401
–20dB E10
TP15
MIC-1-LEV
MIC 1 LEVEL
INCOM
LEV
S201
0dB
–20dB TP43
LV101
RV101
MIC 2 LEVEL
MIC-2-LEV
S301
0dB
–20dB TP7
INCOM MODE
TP3
TP5
MIC TEST
MIC TEST
LV21
1CH
S2004
CH-1
ON
RTS 200
S2006
S2003
CH-2
2.5M CCU DATA LV61 LV41
OHM
4.3M 3.6M
OFF E11
TP2
LEVEL IND
2CH
OFF
E1
TP1
TP46
RTS/CLEAR-COM INCOM SELECT
RV81
RV41
LV1 3.0M
INTER COM H CONT
PGM
DEV
INCOM
DEV
2W
S2005 S2002
(CLEAR
COM ) RTS
4W TP3005
RTS
TP3002
CLEAR
COM E3001
TP3001
TP3004
RV2000
SIDE TONE
TP3003
Note : Perform this adjustment only when replacing 1T401/ Equipment : Oscilloscope, Audio generator
AA-90 board. To be extended : AA-90 board
FM-15 board (CA-TX7/TX7P)
Equipment : Oscilloscope, Audio generator Preparetion :
To be extended : AA-90 board 1. Input the 1 kHz sine wave signal of the audio generator
AFM-15 board (CA-TX7/TX7P) to pin 2 (GND : pin 1) of INTERCOM/PROGRAM
Preparetions : connector (5 pin) on the CA-TX7/TX7P.
1. Input the 1 kHz sine wave signal of the audio generator . Fig-1 (Refer to 4-1-5. Audio connection.)
to pin 2 (GND : pin 1) of INTERCOM/PROGRAM 2. Adjust the output level control of audio generator so that
connector (5 pin) on the CA-TX7/TX7P. the pin 24 (GND : pin 12) /AFM-15 board is 220 mV p-p.
. Fig-1 (Refer to 4-1-5. Audio connection.) Test point : TP15 (GND : E2)/AA-90 board
2. Adjust the output level control of audio generator so that Adjustment point : 1RV401 (INCOM LEVEL)/
the pin 24 (GND : pin 12) /AFM-15 board is 220 mV p-p. AA-90 board
Test point : TP14 (GND : E2)/AA-90 board Specifications : A = 220 ± 10 mV p-p
Adjustment Procedures :
1. Set the input range of oscilloscope to DC made. Adjust
the white core of 1T401/AA-90 board slowly so that the A
DC level at TP14 (GND : E2)/AA-90 board is 1.24 ± 0.01
V dc.
1.24 ± 0.01 V dc
GND
E3001
TP3001
TP3002
TP3004
TP3003
E11
E10
TP46
1CH 2CH
INCOM MODE
S2003
ON OFF
OHM
RTS 200
S2006
Minimum
E1
5.6M TUNE
LV41
3.6M
LV101
DEV
INCOM
LV61
E2 TP6
DEV
TONE TUNE
PGM
3. Repeat procedure 1.
T201
T301
T401
TP5 RV81
TP7
TP1
LEV
2.5M CCU DATA
MIC 1 RV101
LV1 3.0M
RV201 TP2
LEV
H CONT
LV21
MIC 2
RV401
TP12
RV301
TP9
LEV
INCOM
TP15
TP10 TP13
TP44
SIDE TONE
RV2000
S201 S2004
PGM IN S2005 S2002
S2081 MIC-2-LEV
S301 RTS/CLEAR-COM INCOM SELECT
AA-90
CLEAR
MIC 1 LEVEL
MIC 2 LEVEL
INTER COM
–20dB
–20dB
–20dB
LEVEL IND
CH-1
CH-2
COM
MIC TEST
OFF
RTS
RTS
0dB
0dB
0dB
2W
4W
PGM IN
COM )
(CLEAR
Note : Perform this adjustment only when replacing 1T201/ Equipment : Oscilloscope, Audio generator
AA-90 board. To be extended : AA-90 board
AFM-15 board (CA-TX7/TX7P)
Equipment : Oscilloscope, Audio generator Preparations :
To be extended : AA-90 board 1. AUDIO SELECT switch (CAMERA/CA-MIC/CA-LINE)/
Preparations : CA-TX7/TX7P rear panel → "CA-LINE"
1. AUDIO SELECT switch (CAMERA/CA-MIC/CA-LINE)/ 2. Input the 1 kHz sine wave signal of the audio generator to
CA-TX7/TX7P rear panel → "CA-LINE" CH 1 of MIC IN (rear panel) on the CA-TX7/TX7P.
2. Input the 1 kHz sine wave signal of the audio generator to . Fig-2 (Refer to 4-1-5. Audio connection.)
CH 1 of MIC IN (rear panel) on the CA-TX7/TX7P. 3. Adjust the output level control of audio generator so that
. Fig-2 (Refer to 4-1-5. Audio connection.) the pin 19 (GND : pin 12) / AFM-15 board is 220 mV p-p.
3. Adjust the output level control of audio generator so that 4. S201 (0 dB/_20 dB)/AA-90 board → 0 dB
the pin 19 (GND : pin 12)/AFM-15 board is 220 mV p-p. Test point : TP10 (GND : E2)/AA-90 board
Test point : TP8 (GND : E2)/AA-90 board Adjustment point : 1RV201 (MIC 1 LEVEL)/
AA-90 board
Adjustment Procedures :
1. Adjust the white core of 1T201/AA-90 board slowly so
that the DC level at TP8 (GND : E2) /AA-90 board is
1.24 ± 0.01 V dc. 1100 ± 50 mV p-p
1.24 ± 0.01 V dc
GND
Minimum
3. Repeat procedure 1.
CCU-TX7 (E)/V1
4-30
4-7-8. MIC 2 Demodulation Adjustment 4-7-9. MIC 2 Level Adjustment
Note : Perform this adjustment only when replacing 1T301/ Equipment : Oscilloscope, Audio generator
AA-90 board. To be extended : AA-90 board
AFM-15 board (CA-TX7/TX7P)
Equipment : Oscilloscope, Audio generator Preparations :
To be extended : AA-90 board 1. AUDIO SELECT switch (CAMERA/CA-MIC/CA-LINE)/
AFM-15 board (CA-TX7/TX7P) CA-TX7/TX-7P → "CA-LINE"
Preparations : 2. Input the 1 kHz sine wave signal of audio generator to
1. AUDIO SELECT switch (CAMERA/CA-MIC/CA-LINE)/ CH 2 of MIC IN (rear panel) on the CA-TX7/TX7P.
CA-TX7/TX7P → "CA-LINE" . Fig-2 (Refer to 4-1-5. Audio connection.)
2. Input the 1 kHz sine wave signal of the audio generator to 3. Adjust the output level control of audio generator so that
CH 2 of MIC IN (rear panel) on the CA-TX7/TX7P. the pin 17 (GND : pin 12)/AFM-15 board is 220 mV p-p.
. Fig-2 (Refer to 4-1-5. Audio connection.) 4. S301 (0 dB/_20 dB)/AA-90 board → "0 dB"
3. Adjust the output level control of audio generator so that Test point : TP13 (GND : E2)/AA-90 board
the pin 17 (GND : pin 12)/AFM-15 board is 220 mV p-p. Adjustment point : 1RV301 (MIC 2 LEVEL)/
Test point : TP11 (GND : E2)/AA-90 board AA-90 board
Specifications : A = 1100 ± 50 mV p-p
Adjustment Procedures :
1. Adjust the white core of 1T301/AA-90 board slowly so
that the DC level at TP11 (GND : E2) /AA-90 board is
1.24 ± 0.01 V dc. A
1.24 ± 0.01 V dc
GND
TP46
1CH 2CH
INCOM MODE
S2003
ON OFF
OHM
RTS 200
S2006
Minimum
E1
5.6M TUNE
LV41
3.6M
LV101
DEV
INCOM
LV61
E2 TP6
DEV
3. Repeat procedure 1.
TONE TUNE
PGM
T201
T301
T401
TP5 RV81
TP7
TP1
LEV
2.5M CCU DATA
MIC 1 RV101
LV1 3.0M
RV201 TP2
LEV
H CONT
LV21
MIC 2
RV401
TP12
RV301
TP9
LEV
INCOM
TP15
TP10 TP13
TP44
SIDE TONE
RV2000
S201 S2004
PGM IN S2005 S2002
S2081 MIC-2-LEV
S301 RTS/CLEAR-COM INCOM SELECT
AA-90
CLEAR
MIC 1 LEVEL
MIC 2 LEVEL
INTER COM
–20dB
–20dB
–20dB
LEVEL IND
CH-1
CH-2
COM
MIC TEST
OFF
RTS
RTS
0dB
0dB
0dB
2W
4W
PGM IN
COM )
(CLEAR
Notes : Notes :
. This adjustment for the following cameras must be . This adjustment for the following cameras must be
completed before this adjustment. completed before this adjustment.
[For NTSC] DXC-637 or DXC-D30 [For NTSC] DXC-637 or DXC-D30
[For PAL] DXC-637P or DXC-30P [For PAL] DXC-637P or DXC-30P
. Perform the adjustment only when replacing 1LV101 (5.6
MHz TUNE)/AA-90 board. Equipment : Oscilloscope (DC mode)
To be extended : AA-90 board
Equipment : Oscilloscope Test point : TP7 (GND : E2)/AA-90 board
(
20 MHz BW Limit : ON
INPUT made : DC ) Adjustment point : 1RV101 (TONE TUNE)/
AA-90 board
To be extended : AA-90 board
Test point TP6 (GND : E2)/AA-90 board Adjustment Procedures :
Adjustment point : 1LV101 (5.6 MHz TUNE)/ 1. 1RV101 (TONE TUNE)/AA-90 board
AA-90 board → "Mechanical center"
Specifications : _100 ± 40 mV dc 2. Turn 1RV101 (TONE TUNE)/AA-90 board slowly
clockwise and stop it at the point where the sine wave
signal just appears.
GND
A Measure the DC voltage "a"⋅⋅⋅Fig-1
Equal (a)
Turn slowly clockwise
Equal (a)
Equal (b)
(fig. 2)
Equal (a)
A
RV101 (A = B)
B
Equal (b)
(fig. 3)
CCU-TX7 (E)/V1
4-32
SAFETY CHECK-OUT
LEAKAGE TEST
To Exposed Metal
Parts on Set
AC
0.15 µF 1.5 k Ω voltmeter
(0.75V)
Earth Ground
CCU-TX7 (E)/V1
DXBK-701 (UC, CE)
COU-TX7 (UC, CE)
CCU-TX7 (UC) Printed in Japan
CCU-TX7P (CE) E Sony Corporation 2003. 9 11
9-977-286-13 B&P Company ©1997