Beruflich Dokumente
Kultur Dokumente
Service Manual
COLOR Television
CHASSIS : CX-A21FB
Model:
Specification
TV Standard NTSC-M, PAL-M, PAL-N
Sound system AV STEREO
Power consumption 90W
Speaker 5W 8 Ohm x 2
CRT 21” Ultra Slim CRT
Channel indication On screen display
Auxiliary Terminal RCA jack : TV output and AV input
Caution
: In this Manual, some parts can be changed for improving. their
performance without notice in the parts list. So, if you need the
latest parts information, please refer to PPL(Parts Price List)in
Service Information Center.
March 2012
TABLE OF CONTENTS
1.SAFETY INSTRUCTION 2
2.SCHEMATIC DIAGRAM 3
1. SAFETY INSTRUCTION
WARNING : Only competent service personnel may carry out work involving the testing or repair of this equipment
2. The only source of X-RAY Radiation in this TV receiver is the picture tube. For continued X-RAY RADIATION
protection, the replacement tube must be exactly the same type tube as specified in t he parts list.
■ SAFETY PRECAUTION
1. Potentials of high voltage are present when this receiver is operating. Operation of the receiver outside the cabinet or
with the back cover removed involves a shock hazard from the receiver.
1) Servicing should not be attempted by anyone who is not thoroughly familiar with the precautions necessary when
working on high voltage equipment.
2) Discharge the high potential of the picture tube before handling the tube. The picture tube is highly evacuated and if
broken, glass fragments will be violently expelled.
2. If any Fuse in this TV receiver is blown, replace it with the FUSE specified in the Replacement Parts List.
3. When replacing a high wattage resistor (oxide metal film resistor) in circuit board, keep the resistor body 10 mm away
from the circuit board.
4. Keep wires away from high voltage or high temperature components.
5. This receiver must operate under AC 230 volts, 5O Hz. NEVER connect to a DC supply of any other voltage or
frequency.
TOSHIBA-HAY-173
TOSHIBA-HAY-173 TMPA8895CSNG7FU7(NTSC) ADJUSTMENT
■ AGING MODE
1) With factory remote controller to press “D-mode” directly enter AGING mode, screen will display
“factory”. Press “ DISP” key to exit “ factory” to enter “ WHITE BALANCE”.
2) At TV mode, With user remote controller to press “MENU” key to turn to “TUNING” menu, press number
keyboard in 6 seconds “2483”, “ 6483”, “6568”, then enter AGING mode. At AV mode, direct press number
keyboard “2483”, “6483”, “6568”, then enter factory LOGO debugging.
At “ AGING” mode, Press “ MENU” to display main Menu to adjust all data.
■ WHITE
WHITE BALANCE MODE
1) At AGING mode, press “D-mode” exit “ factory” to enter WHITE BALANCE mode.
2) Press “ D-mode” key two time (factory key) to enter WHITE BALANCE mode.
3) At “ factory” mode, press figure key “ 0” enter WHITE BALANCE mode.
4) At WHITE BALANCE mode, press “ MUTE”, one horizontal bright line appear on screen, use “1,4” key to
adjust RCUT, “2,5” key to adjust GCUT, “ 3,6” key to adjust BCUT
■ ENTER
ENTER FACTORY MODE
1:uses the factory's remote controler : Press “ D-mode” key three time (factory key) to enter factory ’s adjustment
menu.
2:At first enter “D-mode” , press “ DISP” enter again WHITE BALANCE mode , press again “DISP” enter factory
mode 。
3:hold the volume minus keybord until sound volume down to zero , press again “DISP” enter “ D-mode”。
■ ENTER
ENTER FACTORY MODE F7~F15
Press “ 2483”,”6483”,”6568” enter F7, and also open F8-F15. Press “Mute” Key to turn Page Up and “ RETURN”
key to turn Page Down for factory mode menu. Press figure Key 1 、2 、 3 、4 、 5、 6、 7to enter “ factory” mode
F1~F7。 press figure key “ 0” enter WHITE BALANCE mode.
■ EXPLANATION
EXPLANATION FOR ADJUSTMENT SPEED KEY
FORADJUSTMENT
After entering factory mode, some remote controller key function will change to suit f or the production
adjustment.
1) Press “MUTE” key to turn page up, press “ RETURN” key to turn page down. press “MENU” choose
adjustment item in pageF10 、F14、F15 .
2) Press “ CH+” and “CH-“ key to select item, and press “ VOL+” and “VOL-” key to change data value.
3) Press “SLEEP” key to display CHIP inner 8 kinds test signal. that is black signal, white signal, cross signal and
pane signal.
TOSHIBA-HAY-173
TOSHIBA-HAY-173 TMPA8895CSNG7FU7(NTSC) ADJUSTMENT
TOSHIBA-HAY-173
TOSHIBA-HAY-173 TMPA8895CSNG7FU7(NTSC) ADJUSTMENT
2: EW
2:EW
3:Brightness、Contrast、Color adjustment
OSD Descriptions Recommend Data Max
SUB.CONT Sub Contrast 10 15
SUB.BRIGHT Brightness 0 -63~63
SUB.COLOR Sub Color 10 -128~—+127
RF.AGC IF Gain 30 63
BACKGrou nd Back grou nd 0:OFF 1 :ON 1 1
BACK.COLOR BACK.COLOR 0: blue 1: black 0 1
BLUE LEVEL Blue Level 1 3
LOGO MOVE 0:Not move 1:Move 0 1
POW.CONT Brightness boost speed for “ POWER ON” 5 15
4:OSD1 adjustment
TOSHIBA-HAY-173
TOSHIBA-HAY-173 TMPA8895CSNG7FU7(NTSC) ADJUSTMENT
0 1 2 3 4 5 6 7 8 9
black blue green orchid red purple yellow white Half black Half blue
10 11 12 13 14 15
Half green Half orchid Half red Half purple Half yellow Half white
TOSHIBA-HAY-173
TOSHIBA-HAY-173 TMPA8895CSNG7FU7(NTSC) ADJUSTMENT
7:OSD2 adjustment
OSD Descriptions Recommend Data Max
POS.TIMER Black screen time adjustment for exchange channels,
10 255
8MS time for data “ 1”
CH DARK Black screen for exchange channels 0:OFF 1:ON 1 1
P.OFF.RGB “ POWER OFF” brightness vanish, 0:OFF 1:ON 0 2
PORTUGUESE Portuguese 0:OFF 1:ON 1 1
SPANISH Spanish 0:OFF 1:ON 1 1
FRENCH French 0:OFF 1:ON 1 1
ENGLISH English 0 :OFF 1 :ON 1 1
BRAZIL Brazil 0: OFF 1 :ON 0 1
CHINESE Chinese 0 :OFF 1 :ON 0 1
TOSHIBA-HAY-173
TOSHIBA-HAY-173 TMPA8895CSNG7FU7(NTSC) ADJUSTMENT
TOSHIBA-HAY-173
TOSHIBA-HAY-173 TMPA8895CSNG7FU7(NTSC) ADJUSTMENT
13:Function control
OSD Descriptions Recommend
Max
Data
V.AGC.DC V. AGC power source selection, 0: external 1: inner 1 1
CVBS output amplitude control,
PIF.LEVER 3 3
0:2.1V 1:2.2V 2:2.3V 3:2.4V
CVBS.PASS Whether CVBS output pass band filter, 0: PASS 1: NO PASS 0 1
Cold “ POWER ON” power pin wait time:
POWER.TIME 0:0 second, 1 :1 second ,2:2 seconds ,3:3 seconds 0 3
TOSHIBA-HAY-173
TOSHIBA-HAY-173 TMPA8895CSNG7FU7(NTSC) ADJUSTMENT
After adjusting the screen G2 , the picture will open once or
V MUTE 1 1
twice 0:once 1:twice
TINT auto recognized display: 1:auto display 0 : always
TINT DSP. 1 1
display
15:R
egister control to Color
5:Register
Recommend Data
OSD Descriptions Max
TV/PAL-N TV/NTSC /PAL-M AV DVD
16:R
egister control to Sound trap
6:Register
OSD Descriptions Recommend Data
Max
M
TOSHIBA-HAY-173
TOSHIBA-HAY-173 TMPA8895CSNG7FU7(NTSC) ADJUSTMENT
VLHf + VHLf
Lf (Highest Freq. of Low Band )( Lowest Freq. of Medium Band ) - 100MHZ
(Low freq.)
2
VHHf + VuLf
Hf (Lowest Freq. of Medium Band )( Lowest Freq. of High Band ) - 300MHZ
(High freq. )
2
TOSHIBA-HAY-173
TOSHIBA-HAY-173 TMPA8895CSNG7FU7(NTSC) ADJUSTMENT
TOSHIBA-HAY-173
TOSHIBA-HAY-173 TMPA8895CSNG7FU7(NTSC) ADJUSTMENT
5.WORK GUIDE
Customer Oper. Name Fixing of the LOGO
Model CRT2135-1P NO. 1/4
Ass'y No. Front cabinet Section CTV Assembly
Fig.1
LOGO
DAEWOO 24MN-1122-002110
Front cabinet
2135-1P Fig.6
Red
White
Fig.2
Fig.3
Fig.5
Fig.4
WORK GUIDE
Customer Oper. Name Fixing of CRT
Model CRT2135-1P NO. 2/4
Ass'y No. Front cabinet Section CTV Assembly
Fig.4
WORK GUIDE
Customer Oper. Name Jointing DY wire
Model CRT2135-1P NO. 3/4
Ass'y No. Back cabinet Section CTV Assembly
DEFLECTION WIRE
14"/21"(450 mm)-B
Fig.3
2
1
2
Fig.2 3 Fig.3
2 3 4
Spongy Cushion×3
15×15×8mm
Fig.4
Chassis
WORK GUIDE
Customer Oper. Name To enlace the wire with strap belt
Model CRT2135-1P NO. 4/4
Ass'y No. Back cabinet Section CTV Assembly
Fig.1
STRAP BELT
Fig.3
Fig.4
STRAP BELT
Fig.5
STRAP BELT
Fig.2