Beruflich Dokumente
Kultur Dokumente
Operating manual
Mode d’emploi
Handleiding
Model L
Elektronik-Heizkörperthermostat (S. 2)
Electronic radiator thermostat (p. 28)
Régulateur d‘économie d‘énergie
pour radiateurs (p. 53)
Energiesparende regelaar voor radiatoren (p. 79)
1
Inhaltsverzeichnis I. Bedienung und Display
I. Bedienung und Display...................................................3
1. Allgemeine Funktion.......................................................4
A
2. Sicherheitshinweise........................................................4
3. Entsorgungshinweise.....................................................4
4. Batterien einlegen (wechseln)........................................5
5. Datum und Uhrzeit einstellen.........................................6
6. Montage am Heizkörper.................................................7
B E
7. Adaptierfahrt.................................................................14
8. Wochenprogramm einstellen........................................14 C F
9. Betriebs-Modi...............................................................19
10. Konfigurationsmenü...................................................19 G H
11. Display-Inhalt im Normalbetrieb..................................20
12. Boost-Funktion...........................................................20 D I
13. Urlaubsfunktion einstellen..........................................21
14. Komfort- und Absenktemperatur................................22 A Überwurfmutter zur Montage am Heizungsventil
15. Kindersicherung / Bediensperre.................................22 B ( ) Urlaubsfunktion, ( ) Absenk-/Komforttemperatur,
16. Heizpause aktivieren (Batterieschonung)...................23 (Manu) Manueller Betrieb, (Auto) Automatikbetrieb
17. Frostschutzbetrieb einstellen......................................23 C ( ) Fenster-auf-Symbol , Wochentag,
18. Fenster-auf-Funktion..................................................23 ( ) Batterie-leer-Symbol
19. Offset-Temperatur einstellen......................................24 D Stellrad: Einstellungen vornehmen (z.B. Temperatur)
20. Werkseinstellungen wieder herstellen........................25 E Eingestellte Schaltzeiträume im Wochenprogramm
21. Bestimmungsgemäßer Einsatz..................................25 F Temperaturanzeige, Zeit-/Datumsanzeige, Menüpunkte,
22. Fehlerbehebung und Wartung....................................26 Funktionen
23. Lieferumfang..............................................................26 G Mode-/Menü-Taste: Taste kurz drücken zum Wech-
24. Technische Eigenschaften..........................................27 seln zwischen Automatikbetrieb, manuellen Betrieb
und Urlaubsfunktion; Taste länger als 3 Sekunden
Lesen Sie diese Anleitung sorgfältig, um das Gerät in Betrieb zu neh-
men. Bewahren Sie die Anleitung zum späteren Nachschlagen auf. drücken zum Öffnen des Konfigurationsmenüs
H -Taste: Umschalten zwischen Absenk-/ Komfort-
1. Ausgabe Deutsch 07/2012 temperatur
Dokumentation © 2012 eQ-3 AG, Deutschland.
Alle Rechte vorbehalten. I Boost-/OK-Taste: Im Automatik- und manuellen Be-
CC-RT-O-CnL-W-R5-2, V1.3, Art-Nr. 130811 trieb, Aktivierung der Boost-Funktion; in der Urlaubs-
funktion und im Menü Bestätigen /Speichern
2 3
1. Allgemeine Funktion Das CE-Zeichen ist ein Freiverkehrszeichen, das
Mit dem Elektronik-Heizkörperthermostat Model L mit vor- sich ausschließlich an die Behörden wendet und
programmiertem, individuell einstellbarem Heiz- und Ab- keine Zusicherung von Eigenschaften beinhaltet.
senkprogramm ist es möglich, die Raumtemperatur zeitge-
steuert zu regulieren. Der Stellantrieb bewegt ein Ventil, um Verbrauchte Batterien gehören nicht in den
den Wärmezustrom am Heizkörper zu steuern. Der Heiz- Hausmüll! Entsorgen Sie diese in Ihrer örtli-
körperthermostat passt auf alle gängigen Heizkörperven- chen Batteriesammelstelle!
tile und ist einfach zu montieren - ohne Ablassen von Hei-
zungswasser oder einen Eingriff in das Heizungssystem.
Die zusätzliche Boost-Funktion ermöglicht ein schnelles, 4. Batterien einlegen (wechseln)
kurzzeitiges Aufheizen des Heizkörpers durch Öffnung des
Ventils für 5 Minuten. Dadurch wird sofort ein angenehmes • Ziehen Sie den Batteriefachde-
Wärmegefühl im Raum erreicht. ckel auf der Unterseite des Ge-
rätes nach hinten ab.
• Legen Sie 2 neue Batteri-
2. Sicherheitshinweise en vom Typ LR6 (Mignon/AA)
Die Geräte sind keine Spielzeuge, erlauben Sie Kindern polungsrichtig in das Batterie-
nicht damit zu spielen. Verpackungsmaterial nicht achtlos fach ein.
liegen lassen, dies kann für Kinder zu einem gefährlichen • Setzen Sie den Batteriefachde-
Spielzeug werden. Öffnen Sie das Gerät nicht, es enthält ckel wieder auf und rasten Sie ihn ein.
keine durch den Anwender zu wartenden Teile. Im Fehler- Die Lebensdauer neuer Alkaline Batterien beträgt ca. 3
fall schicken Sie das Gerät an den Service. Jahre. Ein Batteriesymbol ( ) im Display weist darauf
hin, dass die Batterien auszutauschen sind. Nach Entnah-
me der leeren Batterien sollte bis zum Einlegen der neuen
3. Entsorgungshinweise Batterien ca. 1 Minute gewartet werden. Ein Betrieb mit
Gerät nicht im Hausmüll entsorgen! Akkus ist nicht möglich.
Elektronische Geräte sind entsprechend der Richt-
linie über Elektro- und Elektronik-Altgeräte über Normale Batterien dürfen niemals aufgeladen wer-
die örtlichen Sammelstellen für Elektronik-Altge- den. Es besteht Explosionsgefahr. Batterien nicht
räte zu entsorgen! ins Feuer werfen! Batterien nicht kurzschließen!
4 5
5. Datum und Uhrzeit einstellen 6. Montage am Heizkörper
Wenn Batterien eingelegt oder ausgetauscht werden, wer- Die Montage des Heizkörperthermostaten ist einfach und
den nach kurzer Anzeige der Firmware-Versionsnummer kann ohne Ablassen von Heizungswasser oder Eingriff in
und kurzem Motorlauf automatisch Datum und Uhrzeit das Heizungssystem erfolgen. Spezialwerkzeug oder ein
abgefragt. Abschalten der Heizung sind nicht erforderlich.
• Stellen Sie Jahr, Monat, Tag, Stunde und Mintute (F) Die am Heizkörperthermostat angebrachte Überwurfmut-
mit dem Stellrad (D) ein und bestätigen Sie mit OK (I). ter ist universell einsetzbar und ohne Zubehör passend für
alle Ventile mit dem Gewindemaß M30 x 1,5 mm der gän-
gigsten Hersteller wie z.B.
• Heimeier
• MNG
• Junkers
• Landis&Gyr (Duodyr)
F • Honeywell-Braukmann
• Oventrop
• Schlösser
• Comap
D I • Valf Sanayii
• Mertik Maxitrol
• Watts
Während der Eingabe von Datum und Uhrzeit fährt der • Wingenroth (Wiroflex)
Motor den Steuerstift bereits zurück. • R.B.M
• Die Anzeige „INS“ mit drehendem „∏“ weist darauf hin, • Tiemme
dass der Motor noch zurückfährt. Sobald der Stellantrieb • Jaga
am Ventil montiert werden kann, steht nur „INS“ im Display. • Siemens
• Das Wochenprogramm und andere Einstellungen • Idmar
können vor der Montage angepasst werden. Drü-
cken Sie dazu die Menü-Taste, während in der Anzeige Durch die im Lieferumfang enthaltenen Adapter ist das Ge-
„INS“ steht. Mehr Details finden Sie unter „10. Konfigu- rät auf Heizkörperventile vom Typ Danfoss RA, Danfoss
rationsmenü“. RAV und Danfoss RAVL montierbar.
• Nach abgeschlossener Programmierung steht erneut
„INS“ im Display und die Montage kann erfolgen.
6 7
Demontage des alten Kopfes 6.1. Adapter für Danfoss
Drehen Sie den Thermostatkopf auf den Maximalwert (A) Zur Montage auf Ventile von Danfoss ist einer der beilie-
(gegen den Uhrzeigersinn). Der Thermostatkopf drückt genden Adapter erforderlich. Die Zuordnung des passen-
jetzt nicht mehr auf die Ventilspindel und kann so leichter den Adapterrings zum entsprechenden Ventil entnehmen
demontiert werden. Sie bitte den nachfolgenden Abbildungen.
Die Fixierung des Thermostatkopfes kann unterschiedlich Achten Sie bei der Montage darauf, sich nicht die
ausgeführt sein: Finger zwischen den Adapterhälften einzuklemmen!
• Überwurfmutter: Schrauben Sie die Überwurfmutter
gegen den Uhrzeigersinn ab (B). Danach können Sie Die Ventilkörper von Danfoss weisen umlaufend längliche
den Thermostatkopf abnehmen (C). Einkerbungen (E) auf (siehe Pfeil), die auch einen besse-
• Schnappbefestigungen: Sie können so befestigte Ther- ren Sitz des Adapters nach dem Aufrasten gewährleisten.
mostatköpfe einfach lösen, indem Sie den Verschluss/
Überwurfmutter ein klein wenig gegen den Uhrzeiger- Achten Sie bei der Montage bitte darauf, dass die
sinn drehen (B). Danach können Sie den Thermostat- Zapfen im Inneren des Adapters (D) eine deckungs-
kopf abnehmen (C). gleiche Position zu den Einkerbungen (E) am Ventil
• Klemmverschraubungen: Der Thermostatkopf wird haben.
durch einen Befestigungsring gehalten, der mit einer Rasten Sie den zum Ventil passenden Adapter voll-
Schraube zusammengehalten wird. Lösen Sie diese ständig auf.
Schraube und nehmen Sie den Thermostatkopf vom
Ventil ab (C).
• Verschraubung mit Madenschrauben: Lösen Sie die Ma-
denschraube und nehmen Sie den Thermostatkopf ab (C).
8 9
Die Adapter RA und RAV wurden Zugunsten eines besse- Auf Ventile vom Typ RAV ist vor der Montage die Stößel-
ren Sitzes mit Vorspannung produziert. Bei Montage ver- verlängerung (F) auf den Ventilstift aufzusetzen.
wenden Sie ggf. einen Schraubendreher, und biegen diese
im Bereich der Schraube leicht auf. Nach dem Aufrasten
auf den Ventilkörper befestigen Sie die Adapter bitte mit E
der beiliegenden Schraube und Mutter.
D
Achten Sie bei der Montage bitte darauf, dass die
Zapfen im Inneren des Adapters (D) eine deckungs-
gleiche Position zu den Einkerbungen (E) am Ventil G
haben.
Rasten Sie den zum Ventil passenden Adapter voll-
ständig auf.
12 13
7. Adaptierfahrt oder die gesamte Woche auswählbar (Bsp. Werktage).
Nach dem Einlegen der Batterien fährt der Motor zunächst • Bestätigen Sie mit der OK-Taste.
zurück, währenddessen wird das Datum abgefragt, „InS“ • Der erste Schaltzeitpunkt wird ange-
und das Aktivitätssymbol ( ) angezeigt. Sobald „InS“ ohne zeigt (0:00), dieser kann nicht verän-
Aktivitätssymbol ( ) im Display steht, kann der Heizkör- dert werden. Die Heizzeiten werden
perthermostat montiert werden. Danach wird zur Anpas- zudem als Balken angezeigt.
sung ans Ventil eine Adaptierfahrt („AdA“) durchgeführt. • Bestätigen Sie mit der OK-Taste.
• Danach können Sie die Temperatur einstellen, die ab
• Setzen Sie den Heizkörperthermostat auf das Ventil. 0:00 gewünscht ist (Bsp. 17.0°C).
• Ziehen Sie die Überwurfmutter fest. • Bestätigen Sie mit der OK-Taste.
• Drücken Sie die OK-Taste, wenn im Display „InS“ steht. • Der nächste Schaltzeitpunkt wird
angezeigt (Bsp. 6:00). Diesen kön-
Der Stellantrieb führt eine Adaptierfahrt durch. Dabei nen Sie individuell anpassen.
werden „AdA“ und das Aktivitätssymbol ( ) im Display • Stellen Sie anschließend die Tem-
angezeigt, währenddessen ist keine Bedienung möglich. peratur ein, die ab 6:00 vorherrschen soll.
• Diesen Vorgang können Sie wieder-
Wurde die Adaptierfahrt vor der Montage eingeleitet, holen, bis die weiteren gewünsch-
drücken Sie die OK-Taste und der Motor fährt zurück ten Temperaturen für den Zeitraum
zur Position „InS“. Wird eine Fehlermeldung (F1, F2, von 0:00 bis 23:59 h hinterlegt sind.
F3) angezeigt, fährt der Motor ebenfalls zurück zur • Sind alle 7 Schaltzeitpunkte belegt,
Position „InS“. wird 23:59 als Endzeitpunkt zum
Bestätigen angezeigt.
8. Wochenprogramm einstellen
Im Auto-Modus kann die Temperatur jederzeit auch über
Im Wochenprogramm lassen sich für jeden Wochentag se- das Stellrad verändert werden. Die geänderte Tempera-
parat bis zu 3 Heizphasen (7 Schaltzeitpunkte) einstellen. tur bleibt dann bis zum nächsten Schaltzeitpunkt erhalten.
Die Programmierung erfolgt für die ausgewählten Tage,
wobei für einen Zeitraum von 00:00 bis 23:59 Temperatu-
ren hinterlegt werden können. 8.1. Wochenprogramm: Beispiele
• Drücken Sie die Menü-Taste länger als 3 Sekunden. Im Mit dem Heizkörperthermostaten können für jeden Wo-
Display erscheint „PRO“. Bestätigen Sie mit der OK-Taste. chentag bis zu 3 Heizzeiten (7 Schaltzeitpunkte) mit indi-
• Im Display erscheint „DAY“. Mit dem Stellrad sind ein vidueller Temperaturvorgabe hinterlegt werden.
einzelner Wochentag, alle Werktage, das Wochenende
14 15
Werkseitig sind zwei Heizphasen von 6:00 bis 9:00 Uhr Soll ein Raum auch zur Mittagszeit beheizt werden, kann
und von 17:00 bis 23:00 Uhr für alle Wochentage gleich eine Programmierung wie folgt aussehen:
hinterlegt:
Montag bis Sonntag
ab 00:00 bis 06:00 17.0°C ab 00:00 bis 06:00 16.0°C
ab 06:00 bis 09:00 21.0°C ab 06:00 bis 09:00 22.0°C
ab 09:00 bis 17:00 17.0°C ab 09:00 bis 12:00 17.0°C
ab 17:00 bis 23:00 21.0°C ab 12:00 bis 14:00 20.0°C
ab 23:00 bis 23:59 17.0°C ab 14:00 bis 17:30 17.0°C
ab 17:30 bis 23:30 21.0°C
ab 23:30 bis 23:59 16.0°C
16 17
Haben Sie zu Hause ein Büro und möchten dies nur tags- 9. Betriebs-Modi
über an Werktagen heizen, könnten Sie die folgenden Zei- Mit kurzem Druck der Mode-Taste kann zwischen den fol-
ten programmieren: genden 3 Betriebsmodi gewechselt werden (die Betriebs-
Modi sind erst nach der Installation/Schritt 3 auswählbar):
Montag bis Freitag • ( ) Urlaubsfunktion: Einstellen einer Temperatur,
ab 00:00 bis 08:30 17.0°C die bis zu einem fixen Zeitpunkt gehalten werden soll.
ab 08:30 bis 17:00 21.0°C • Manu: Manueller Betrieb - die Temperatur wird manuell
ab 17:00 bis 23:59 17.0°C über das Stellrad eingestellt.
• Auto: Wochenprogramm - automatische Temperaturrege-
lung entsprechend dem hinterlegtem Wochenprogramm.
10. Konfigurationsmenü
Im Konfigurationsmenü lassen sich Einstellungen ändern.
Das Menü lässt sich über einen langen Tastendruck (länger
als 3 Sekunden) der Menü-Taste aufrufen. Menüpunkte wer-
den mit dem Stellrad ausgewählt und mit OK bestätigt. Ein
erneuter Druck der Menü-Taste führt zur vorherigen Ebene
zurück. Wenn für mehr als 65 Sekunden keine Betätigung
am Gerät erfolgt, schließt sich das Menü automatisch. Sie
Samstag bis Sonntag können folgende Einstellungen vornehmen:
ab 00:00 bis 23:59 15.0°C
PRO: Einstellung des Wochenprogramms (siehe
Abschnitt „8. Wochenprogramm einstellen“)
18 19
• Die verbleibende Funktionsdauer wird im Sekundentakt
AER: Fenster-auf-Temperatur und -Zeit für die au-
tomatische Temperaturabsenkung beim Lüf- heruntergezählt („B299“ bis „B000“).
ten einstellen • Nach Ablauf dieser 5 Minuten wechselt der Stellantrieb
in den vorher aktiven Modus (Auto/Manu) mit der vorher
TOF: Offset-Temperatur einstellen eingestellten Temperatur.
• Die Funktion lässt sich jederzeit vorzeitig durch einen
RES: Werkseinstellungen wieder herstellen Tastendruck oder Betätigen des Stellrads deaktivieren.
24 25
22. Fehlerbehebung und Wartung 24. Technische Eigenschaften
Fehlercode im Versorgungsspannung: 3V
Problem Behebung Max. Stromaufnahme: 100 mA
Display
Batteriesymbol Batterieleistung Batterien Batterien: 2x LR6 / Mignon / AA
( ) zu gering austauschen Batterielebensdauer: ca. 3 Jahre
Installation prüfen, Display: LC-Display
Ventilantrieb Gehäuseabmessung: 58 x 71,5 x 90 mm (B x H x T)
F1 Heizungsventil
schwergängig Anschluss: M30 x 1,5
überprüfen
Befestigung Umgebungstemperatur: 0 bis 55 °C
Stellbereich Max.
F2 des Heizkörperther-
zu groß Oberflächentemperatur: +90°C (am Heizkörper)
mostaten überprüfen
Stellbereich Heizungsventil Linearer Hub: 4,3 mm
F3 zu klein überprüfen
Technische Änderungen, die zur Verbesserung
Zum Schutz vor Ventilverkalkung führt der Heizkör- dienen, sind vorbehalten.
perthermostat einmal wöchentlich am Samstag um
12:00 h eine Entkalkungsfahrt durch. Dabei erscheint
„CAL“ im Display.
23. Lieferumfang
Elektronik-Heizkörperthermostat
Adapter Danfoss RA
Adapter Danfoss RAV
Stößelverlängerung Danfoss RAV
Adapter Danfoss RAVL
Zylinderkopfschraube M4 x 12, Mutter M4
Stützring
26 27
Table of contents I. Operation and display
I. Operation and display...................................................29
1. General function...........................................................30 A
2. Safety advice................................................................30
3. Disposal........................................................................30
4. Inserting/replacing batteries.........................................31
5. Setting the date and time.............................................32
6. Installation on the radiator............................................33
B E
7. Adapting run.................................................................40
8. Setting the weekly program..........................................40 C F
9. Operating Modes..........................................................45
10. Configuration menu....................................................45
11. Display content in normale Mode...............................46
G H
12. Boost function.............................................................46 D I
13. Setting the holiday function........................................47
A Union nut for fitting on the heating valve
14. Comfortable temperature and reduced temperature..47
B ( ) Holiday function, ( ) reduced temperature/
15. Child safeguard/operating lock...................................48
comfortable temperature, (Manu) manual Mode,
16. Activating heating pause (battery saving)...................48
(Auto) automatic Mode
17. Setting the frost protection Mode...............................49
C ( ) „Window open“ symbol, weekday,
18. „Window open“ function..............................................49
( ) „Battery empty“ symbol
19. Setting the offset temperature....................................50
D Selector dial: perform settings (e.g. temperature)
20. Restoring the factory settings.....................................50
E Set switching time periods in the weekly program
21. Intended use...............................................................51
F Temperature display, time/date display, menu items,
22. Troubleshooting and maintenance.............................51
functions
23. Scope of delivery........................................................52
G Mode/Menu key: press the key briefly to change bet-
24. Technical data.............................................................52
ween automatic Mode, manual Mode and holiday func-
Please read this manual carefully in order to help you put the de- tion; press the key longer than 3 seconds to open the
vice into operation. Keep the manual handy so you can refer to it configuration menu
at a later date! H -key: switching between reduced temperature/com-
1. English edition 07/2012 fortable temperature
Documentation © 2012 eQ-3 AG, Germany. I Boost-/OK-key: in automatic and manual Mode, ac-
All rights reserved. tivation of the Boost function; in the holiday function
CC-RT-O-CnL-W-R5-2, V1.3, Art-No. 130811
and in the Confirm/Save menu
28 29
1. General function The CE sign is a free trade sign addressed exclu-
The programmable electronic radiator thermostat Model L sively to the authorities and does not include any
offers a pre-programmed heating and temperature reducing warranty of any properties.
program. The program can be set individually and it is pos-
sible to control the room temperature in a time-controlled Never dispose of batteries in your household
manner. The device moves a valve to control the flow of waste. Defective or used batteries must be
heat to the radiator. The programmable radiator control unit recycled in accordance with Directive 2006 /
fits all common radiator valves and is easy to install - wit- 66 / EC. Return batteries and / or the device
hout discharging the heating water or interfering with the to the recycling facilities offered.
heating system. The additional Boost function enables the
radiator to be heated up quickly for a brief period of time by
opening the valve for 5 minutes. This gives an immediate 4. Inserting/replacing batteries
and pleasant feeling of warmth in the room.
• Pull off the battery compart-
ment cover on the underside of
2. Safety advice the device.
The devices concerned are not intended for children and • Insert 2 new LR6 (Mignon / A
must not be used as toys. Do not leave packaging material A) batteries into the battery
lying around, as children might be tempted to play with it, compartment with the correct
which is extremely dangerous. Do not open the device: it polarity.
does not contain any components that need to be serviced • Replace the battery cover and
by the user. In the event of an error, please return the de- latch it in.
vice to our service department. The life span of new alkaline batteries is approx. 3 years. A
battery symbol ( ) indicates that the batteries should
be replaced. After the batteries have been removed, you
3. Disposal should wait approx. 1 minute before inserting the new batte-
Do not dispose off the device as part of household ries. Operation with rechargeable batteries is not possible.
garbage! Electronic devices are to be disposed of
in accordance with the guidelines concerning elec- Never recharge non-rechargeable batteries and do
trical and electronic devices via the local collecting not short-circuit and / or open any batteries. The
point for old electronic devices. battery may overheat, ignite or explode. Never throw
batteries into fire or water. The batteries may explo-
de.
30 31
5. Setting the date and time 6. Installation on the radiator
If batteries are inserted or replaced, the date and time is The installation of the programmable radiator control unit is
automatically requested after a brief display of the firmwa- easy and can be performed without discharging the heating
re version number. water or interfering with the heating system. Special tools or
• Set the year, month, day, hour and minute (F) with the switching off the heating are not required. The union nut
selector dial (D) and confirm with OK (I). fitted to the programmable radiator control unit can be used
universally and without accessories for all valves with a th-
read dimension of M30 x 1.5 mm from the most common
suppliers, such as for example
• Heimeier
• MNG
• Junkers
• Landis&Gyr (Duodyr)
F • Honeywell-Braukmann
• Oventrop
• Schlösser
• Comap
• Valf Sanayii
D I • Mertik Maxitrol
• Watts
• Wingenroth (Wiroflex)
The motor moves the control pin backwards during the set-
• R.B.M
ting of the date and time.
• Tiemme
• The display of „INS“ with the rotating „∏“ shows that the
• Jaga
motor is still travelling back. When only „INS“ is shown
• Siemens
in the display, the actuator can be installed on the valve.
• Idmar
• The weekly program and other settings can be ad-
justed before installation. Press the Menu key for this,
By means of the adapters in the delivery, the device can be
while „INS“ is shown in the display. You can find more
installed on radiator valves of type Danfoss RA, Danfoss
details under „10. Configuration menu“.
RAV and Danfoss RAVL.
• After the programming has been completed, „INS“ is
shown again in the display and installation can take place.
32 33
Removing the old thermostat head 6.1. Adapters for Danfoss
Turn the thermostat head to the maximum value (A) in an One of the enclosed adapters is required for installation
anticlockwise direction. The thermostat head does not on Danfoss valves. The arrangement of the suitable ad-
now press on the valve spindle and it can therefore be re- apter ring for the appropriate valve can be found in the
moved more easily following figures:
There can be different types of thermostat head fixing: Take care during installation that you do not trap your
• Union nut: Unscrew the union nut in an anticlockwise di- fingers between the two halves of the adapter!
rection (B). Then you can remove the thermostat head (C).
• Snap-on fastenings: You can easily release thermostat The Danfoss valve bodies have elongated indentations (E)
heads fastened in this way by turning the closure faste- running all around (see arrow), which also ensure better
ning/union nut a small amount in an anticlockwise direc- seating of the adapter after it has been latched into place.
tion (B) Then you can remove the thermostat head (C).
• Clamping screw connections: The thermostat head is When installing, please ensure that the spigots inside
held by means of a fastening ring, which is held together the adapter (D) are in the same position as the inden-
by a screw. Release this screw and remove the thermo- tations (E) on the valve.Latch the adapter, which cor-
stat head from the valve (C). responds to the valve, completely onto the valve body.
• Screw connection with setscrews: Release the setscrew
and remove the thermostat head (C).
34 35
The RA and RAV adapters have been produced with pre- With the RAV type of valve, the tappet extension (F) should
tension to aid better seating. Use a screw driver during in- be placed on the valve pin before installation.
stallation if necessary and bend these gently upwards in
the area of the screw. After they have been latched onto
the valve body, fasten the adapters with the enclosed E
screw and nut
36 37
The RAVL adapter does not have to be screwed on. Retaining ring
The valves of a number of suppliers can exhibit tolerance
variations, which may lead to the programmable radiator
control unit being seated too loosely on the valve. The sta-
E bility and seating on the valve can be improved by using
the enclosed retaining ring. Place the retaining ring (G) in
the flange or on the valve connection of the radiator and
screw the thermostat valve on.
If the retaining ring can not be fitted, the stability is already
sufficient and the ring is not required for the installation.
38 39
7. Adapting run • Confirm with the OK key.
After the batteries have been inserted, the motor first travels • The first switching time point is dis-
back, during which the date, „INS“ and the activity sym- played (0:00), this can not be chan-
bol are displayed. As soon as „INS“ without the activity ged. The heating times are also dis-
symbol is displayed, the programmable radiator control played as bars.
unit can be installed. An adapting run („AdA“) is performed • Confirm with the OK key.
after installation to adapt to the valve. • After this you can set the temperature which is desired
from 0:00 (example 17.0 °C).
• Place the programmable radiator control unit on the val- • Confirm with the OK key.
ve. • The next switching time point is dis-
• Tighten the union nut firmly. played (example 6:00). You can ad-
• Press the OK key , when „INS“ is shown in the display. just this individually.
• Finally set the temperature which
The actuator carries out an adapting run. During this time should prevail from 6:00.
„AdA“ and the activity symbol are shown in the display • You can repeat this procedure un-
and operation is not possible. til all the other desired temperatu-
res for the time period from 0:00 to
If the adapting run is initiated before installation, press 23:59 have been stored.
OK and the motor travels back to the „INS“ position. • If all 7 switching time points have
If an error message (F1, F2, F3) is displayed, the motor been allocated, 23:59 is displayed
similarly travels back to the „INS“ position. as the final switching point to be
confirmed.
8. Setting the weekly program
Up to 3 heating phases (7 switching time points) can be set The temperature can also be changed in Auto Mode at any
separately for each weekday in the weekly program. The time via the selector dial.The changed temperature is then
programming is done for the selected days and tempera- retaineduntil the next switching time point.
tures must be stored for a time period from 00:00 to 23:59.
• Press the Menu key longer than 3 seconds. „PRO“ ap- 8.1. Weekly program: examples
pears in the display. Confirm with the OK key. Up to 3 heating times (7 switching time points) with individual
• „DAY“ appears in the display. With the selector dial can temperature setting can be stored for each weekday with the
be selected an individual weekday, all working days, the programmable radiator control unit.
weekend or the whole week (example working days).
40 41
Two heating phases from 6:00 to 9:00 and from 17:00 to If a room is also to be heated at midday, the programming
23:00 for all weekdays alike are saved as factory settings: can appear as follows:
42 43
If you have an office at home and only want to heat this 9. Operating Modes
throughout the day on working days, you could program By briefly pressing the Mode key, you can change between
the following times: the following 3 operating Modes (the operating Modes can
only be selected after installation / step 3):
Monday to Friday • ( ) Holiday function: Setting a temperature, which has
from 00:00 to 08:30 17.0°C to be maintained until a fixed point in time.
from 08:30 to 17:00 21.0°C • Manu: Manual Mode - the temperature is set manually
from 17:00 to 23:59 17.0°C via the selector dial.
• Auto: Weekly program - automatic temperature control
corresponding to the saved weekly program.
11. Display content in normal Mode 13. Setting the holiday function
Switching time periods, operating Mode, target tempera- If a fixed temperature needs to be maintained during a
ture and week day are displayed in normal Mode. The bars holiday or a party for a certain period of time, the holiday
for the switching time periods function can be used.
of the weekly program are dis-
played for every second time • Press the Mode key briefly as often as necessary until the
interval (see example under Suitcase symbol ( ) appears in the display.
„8.1 Weekly program: examp- • Set the time via the selector dial up to which the tempera-
les“). ture is to be maintained and then confirm with the OK key
• Then set the date with the selector dial and confirm with
12. Boost function the OK key.
The Boost function uses the human perception of warmth. • Set the temperature with the selector dial and confirm
When activated, the heating valve is immediately opened with the OK key. The display flashes as confirmation.
to 80% for 5 minutes (factory setting). The heating of a
room takes longer than 5 minutes, but the heat given off The set temperature is maintained until the time point which
by the radiator can be felt immediately. If you are coming has been set. After this the actuator goes into Auto Mode.
home earlier and want to have heat quickly, or if you need
extra heat in the morning for a bath, then the Boost func- 14. Comfortable temperature and
tion will help you. reduced temperature
The key for comfortable temperature / reduced tempera-
• Press the Boost key to activate the Boost function.
ture ( ) provides for a convenient and simple switching
• The remaining duration of the function is counted down
between these two temperatures. These have been set at
in seconds („B299“ to „B000“).
the factory at 21.0 °C (comfortable temperature) and 17.0
• After these 5 minutes have elapsed, the actuator chan-
°C (reduced temperature). They can be adjusted as follows:
ges to the Mode which was previously active (Auto/Manu)
with the previously set temperature.
• Hold the key for Comfortable temperature/ reduced tem-
• The function can be deactivated early at any time by pres-
perature ( ) for a long period.
sing the key or activating the selector dial.
• The Sun symbol ( ) and the currently stored comfortab-
46 47
le temperature appear in the display. 17. Setting the frost protection Mode
• Change the temperature with the selector dial and con- If a room is not to be heated, the valve can be closed.
firm with the OK key. • Turn the selector dial in manual Mode (Manu) to the left
• The Moon symbol ( ) and the reduced temperature ap- until „OFF“ appears in the display.
pear in the display. •
• Change the temperature with the selector dial and con- The valve is only opened if there is danger of frost. The protec-
firm with the OK key. tion against calcification continues however to be carried out.
The temperature can also be changed in Auto Mode at any • To end it, exit the manual Mode (Manu) or turn the se-
time via the key. This is then retained until the next swit- lector dial to the left.
ching time point of the program.
48 49
19. Setting the offset temperature 21. Intended use
Since the temperature is measured at the radiator, it can The programmable radiator control unit is used to control
be colder or warmer at another location in the room. In or- a conventional radiator valve. Only operate the device in
der to equalise this, a temperature offset of +/- 3.5 °C can inside rooms and avoid the influence of moisture, dust and
be set. If for example 18 °C is measured instead of the set sunlight or external heat radiation. Any type of use other
20 °C, then an offset of -2.0 °C is to be set. than that described in these operating instructions does
not comply with the intended use and leads to automatic
To set the offset temperature proceed as follows: exclusion from warranty and liability claims. This also ap-
• Press the Menu key longer than 3 seconds. plies in the case of conversions and modifications. The
• Select the „OF“ menu item with the selector dial and con- devices are solely intended for private use.
firm with the OK key
• Turn the selector dial for as long as necessary until the
desired temperature appears. 22. Troubleshooting and maintenance
• Confirm with the OK key.
Error code in Problem Rectification
the display
20. Restoring the factory settings Battery symbol Battery output Replace the bat-
( ) too low teries
The status of the programmable radiator control unit can
Valve drive is Check the installati-
be manually restored by means of a reset to that when ori- F1 stiff to move on and heating valve
ginally supplied. This means that all the manually perfor-
Actuating range Check the fastening
med settings are lost. F2 of the radiator con-
Follow these steps: too large trol unit
• Hold the Menu key pressed down for longer than 3 se-
Actuating range Check the heating
conds. F3 too small valve
• Select the „RES“ menu item with the selector dial and con-
firm with the OK key. „CFM“ then appears in the display. The programmable radiator control unit performs a
• „CFM“ then appears in the display. decalcifying run once a week on Saturday at 12:00 to
• Confirm with the OK key. protect against calcification of the valve. During this
„CAL“ appears in the display.
50 51
23. Scope of delivery Table des matières
I. Utilisation et affichages................................................54
Electronic radiator thermostat 1. Fonctions générales....................................................55
2. Consignes de sécurité.................................................55
Danfoss RA adapter 3. Consignes pour l’élimination.......................................55
Danfoss RAV adapter 4. Insérer / remplacer les piles........................................56
Danfoss RAV tappet extension 5. Régler la date et l’heure...............................................57
Danfoss RAVL adapter 6. Montage sur le radiateur..............................................58
Cylinder head screw M4 x 12, Nut M4 7. Phase d’adaptation......................................................65
8. Réglage du programme hebdomadaire......................65
Retaining ring 9. Modes de fonctionnement...........................................70
10. Menu de configuration...............................................70
11. Contenu de l’écran en Mode normal.........................71
24. Technical data 12. Fonction Boost...........................................................71
Supply voltage: 3V 13. Réglage de la fonction congés..................................72
Max. current loading: 100 mA 14. Température confort et abaissement........................73
Batteries: 2x LR6 / Mignon / AA 15. Protection enfant / Verrouillage.................................73
Battery life span: approx. 3 Jahre 16. Activation de la pause de chauffage
Display: LC display (pour économiser les piles)......................................74
Housing dimensions: 58 x 71,5 x 90 mm (w x h x d) 17. Réglage du Mode hors gel........................................74
Connection: M30 x 1,5 18. Fonction « fenêtre ouverte ».....................................74
Ambient temperature: 0 bis 55 °C 19. Réglage de la température offset..............................75
Max. 20. Réinitialisation des réglages d’usine.........................76
Surface temperature: +90°C (at the radiator) 21. Utilisation conforme...................................................76
Linear lift: 4,3 mm 22. Elimination des défauts et entretien..........................77
23. Contenu de la livraison..............................................77
Subject to technical changes. 24. Caractéristiques techniques......................................78
Lisez soigneusement la présente notice pour l’utilisation de l’appareil.
Conservez la notice pour pouvoir vous y référer ultérieurement.
58 59
6.1. Adaptateur pour Danfoss Les adaptateurs RA et RAV ont été fabriqués dans le but
L’un des adaptateurs joints est nécessaire pour le mon- d’améliorer la fixation. Pour le montage, utilisez le cas
tage sur des vannes Danfoss. L’attribution de la bague échéant un tournevis et relevez légèrement dans la zone
d’adaptateur convenable à la valve correspondante est de la vis. Après l’enclenchement sur le corps de la vanne,
indiquée dans les illustrations. fixez les adaptateurs à l’aide de la vie et de l’écrou joints.
D
Pendant le montage, veillez à ce que les pivots à
l’intérieur de l’adaptateur (D) recouvrent parfaitement
les encoches (E) de la vanne.
Enclenchez entièrement l’adaptateur adapté à la
vanne.
60 61
Si vous utilisez des vannes RAV, posez la rallonge du cou- L’adaptateur RAVL ne doit pas être vissé.
lisseau (F) sur la cheville de la vanne avant le montage
E E
D
D
Pendant le montage, veillez à ce que les pivots à
l’intérieur de l’adaptateur (D) recouvrent parfaitement
Pendant le montage, veillez à ce que les pivots à les encoches (E) de la vanne.
l’intérieur de l’adaptateur (D) recouvrent parfaitement Enclenchez entièrement l’adaptateur adapté à la
les encoches (E) de la vanne. vanne.
Enclenchez entièrement l’adaptateur adapté à la
vanne.
62 63
Bague de support 7. Phase d’adaptation
Les vannes de différentes marques peuvent présenter des Une fois les piles en place, le moteur revient d’abord en
tolérances variables entraînant une mauvaise fixation du arrière, entre temps, « INS » et le symbole d’activité (
thermostat de radiateur sur la vanne. En utilisant la bague ) s’affichent. Dès que « INS » apparaît sur l’écran sans le
de support jointe, la stabilité et la fixation sur la vanne peu- symbole d’activité ( ) , le thermostat de radiateur program-
vent être améliorés. mable peut être monté. Puis l’appareil fait une marche test
Insérez la bague de support (G) dans la bride ou sur le pour l’adaptation à la vanne (AdA).
raccord de vanne du radiateur et vissez la vanne ther-
mostatique. • Posez le thermostat de radiateur programmable sur la
Si la bague de support ne peut pas être insérée, la sta- vanne.
bilité est suffisante et son montage n’est pas nécessaire. • Serrez l’écrou-raccord à fond.
• Appuyez sur la touche OK si l’écran affiche « INS ».
66 67
L’écran affiche des barres pour les périodes d’un cyc- Si vous avez un bureau à la maison et si vous souhaitez le
le sur deux. Cet exemple n’affiche pas de barres pour chauffer uniquement pendant la journée les jours ouvrés,
le cycle de 0:00 à 6:00. Les barres ne s’affichent que vous pouvez programmer les heures suivantes:
pour les cycles de 6:00 à 9:00 et 17:00 à 23:00.
Lundi à vendredi
Si une pièce doit aussi être chauffée à l’heure de midi, la de 00:00 à 08:30 17.0°C
programmation peut se présenter comme suit: de 08:30 à 17:00 21.0°C
de 17:00 à 23:59 17.0°C
Lundi à dimanche
de 00:00 à 06:00 16.0°C
de 06:00 à 09:00 22.0°C
de 09:00 à 12:00 17.0°C
de 12:00 à 14:00 20.0°C
de 14:00 à 17:30 17.0°C
de 17:30 à 23:30 21.0°C
de 23:30 à 23:59 16.0°C
Samedi à dimanche
de 00:00 à 23:59 15.0°C
68 69
9. Modes de fonctionnement
AER: Réglage de la température et de l’heure «
En appuyant légèrement sur la touche Mode , vous pouvez fenêtre ouverte » pour l’abaissement auto-
choisir entre les 3 Modes (ces Modes ne peuvent être sé- matique de la température pendant l’aération
lectionnés qu’après le montage): des pièces.
• ( ) Fonction congés: réglage d’une température à
TOF: Réglage de la température offset
respecter jusqu’à une heure déterminée.
• Manu: Mode manuel - la température est réglée à la main RES: Réinitialisation des réglages d’usine
via le bouton de réglage rotatif.
• Auto: programme hebdomadaire - régulation automa-
tique de la température en fonction du programme heb- 11. Contenu de l’écran en Mode normal
domadaire enregistré.
En Mode normal, les périodes de commutation, le Mode
de fonctionnement, la température de consigne et le jour
10. Menu de configuration
de la semaine s’affichent.
Le menu de configuration permet de modifier les réglages. Les barres des périodes de
Ce menu peut être sélectionné en appuyant longuement commutation du programme
(plus de 3 secondes) sur la touche du menu. Les menus sont hebdomadaire s’affichent
sélectionnés avec le bouton de réglage rotatif et confirmés tous les deux cycles (exem-
avec OK. En réappuyant sur la touche de menu, vous reve- ple dans « Programme heb-
nez au niveau précédent. Si vous n’intervenez pas pendant domadaire: exemples »).
plus de 65 secondes, le menu se ferme automatiquement.
Vous pouvez effectuer les réglages suivants:
12. Fonction Boost
PRO: Réglage du programme hebdomadaire (voir
paragraphe « Réglage du programme heb- La fonction Boost utilise la sensation de chaleur humaine.
domadaire ») En activant cette fonction, la vanne s’ouvre immédiatement
pendant 5 minutes à 80 % (réglage d’usine). Une pièce a
DAT: Modification de l’heure et de la date besoin de plus de 5 minutes pour se réchauffer, mais la
POS: Demande de la position actuelle du servo- chaleur restituée par le radiateur peut être ressentie immé-
moteur diatement. La fonction Boost vous est utile si vous rentrez
chez vous plus tôt que prévu et que vous souhaitez avoir
DST: La commutation automatique entre l’heure chaud rapidement, ou si vous avez besoin de plus de cha-
d’été et l’heure d’hiver peut être désactivée. leur le matin dans la salle de bain.
70 71
• Appuyez sur la touche Boost pour activer la fonction 14. Température confort et abaissement
correspondante. La touche confort / abaissement ( ) permet de commu-
• La durée restante est décomptée par secondes (« B299 ter facilement et simplement entre ces deux températures.
» à « B000 »). L’appareil est livré avec une température confort de 21.0 °C
• Après écoulement de ces 5 minutes, le servomoteur re- et une température d’abaissement de 17.0 °C. Elles peu-
vient au Mode précédent (Auto/Manu) avec l’ancienne vent être adaptées comme suit:
température réglée.
• Cette fonction peut être désactivée à tout moment en ap- • Appuyez longtemps sur la touche confort / abaisse-
puyant sur une touche ou en tournant le bouton de réglage ment ( ).
• L’écran affiche le symbole soleil ( ) et la température
La touche Boost n’a pas d’effet direct si le radiateur confort actuellement enregistrée.
est recouvert (par ex. par un divan). La détection « • Modifiez la température avec le bouton rotatif et confir-
fenêtre ouverte » est désactivée pendant la fonction mez avec la touche OK.
Boost. • L’écran affiche le symbole lune et la température
d’abaissement.
13. Réglage de la fonction congés • Modifiez la température avec le bouton rotatif et confir-
Cette fonction peut être utilisée si une température déter- mez avec la touche OK.
minée doit être maintenue pour une période définie pen-
dant les congés ou au cours d’une réception. En Mode automatique, la température peut également
être modifiée n’importe quand avec la touche. Celle-ci est
• Appuyez rapidement sur la touche Menu aussi souvent alors maintenue jusqu’au prochain point de commutation
que nécessaire pour afficher le symbole valise ( ). du programme.
• Réglez à l’aide du bouton rotatif l’heure jusqu’à laquel-
le la température doit être maintenue et confirmez avec
la touche OK 15. Protection enfant / Verrouillage
• Réglez ensuite la date avec le bouton rotatif, et confir-
L’appareil peut être verrouillé:
mez avec la touche OK.
• Réglez la température à l’aide du bouton rotatif et confir-
• Pour activer / désactiver le verrouillage, appuyez rapide-
mez avec OK. Le message clignote pour être confirmé.
ment et simultanément sur les touches de menu et .
Une fois le verrouillage activé, « LOC » s’affiche.
La température réglée est maintenue jusqu’à l’heure en-
• Pour désactiver le verrouillage, réappuyez sur les deux
registrée. Le servomoteur passe ensuite en Mode auto-
matique. touches.
72 73
16. Activation de la pause de chauffage Pour activer, procédez comme suit:
(pour économiser les piles) • Appuyez sur la touche de menu pendant plus de 3 se-
condes.
Vous pouvez économiser les piles si le chauffage est arrêté • Sélectionnez à l’aide du bouton rotatif le menu « AER »
en été. Pour cela, ouvrir la vanne entièrement. La protec- et confirmez avec la touche OK
tion anti-tartre est maintenue. • La température et l’heure peuvent être réglées à l’aide
du bouton rotatif. La sélection « 0 » permet de désacti-
Pour activer la pause chauffage, procédez comme suit: ver la fonction.
• Tournez le bouton de réglage en Mode manuel (Manu)
vers la droite jusqu’à ce que « On » s’affiche.
• Pour terminer, quittez le Mode manuel (Manu) ou tour- 19. Réglage de la température offset
nez le bouton vers la gauche.
Comme la température est mesurée sur le radiateur, il se
peut qu’il fasse plus chaud ou plus froid dans une autre
17. Réglage du Mode hors gel partie de la pièce. Pour compenser cette différence, il est
possible de régler un offset de ±3.5 °C. Si, par exemple,
Si une pièce ne doit pas être chauffée, il est possible de 18 °C sont mesurés au lieu des 20 °C réglés, il faut régler
fermer la vanne. un offset de -2.0 °C.
• Tournez le bouton de réglage en Mode manuel (Manu)
vers la gauche jusqu’à ce que « OFF » s’affiche. Pour régler la température offset, procédez comme suit:
• Appuyez sur la touche de menu pendant plus de 3 se-
La vanne ne s’ouvre que s’il y a risque de gel. La protection condes.
antitartre est maintenue. • Sélectionnez à l’aide du bouton rotatif le menu « OF » et
confirmez avec la touche OK.
• Pour terminer, quittez le Mode manuel (Manu) ou tour- • Tournez le bouton jusqu’à ce que la température souhai-
nez le bouton vers la droite. tée s’affiche.
• Confirmez avec la touche OK.
adaptateur Danfoss RA
adaptateur Danfoss RAV
rallonge coulisseau Danfoss RAV
adaptateur Danfoss RAVL
vis à tête cylindrique M4 x 12, écrou M4
bague de support
76 77
24. Caractéristiques techniques Inhoudsopgave
Tension d’alimentation: 3V I. Bediening en display.....................................................80
Puissance électrique 1. Algemene functie..........................................................81
absorbée maxi.: 100 mA 2. Veiligheidsinstructies....................................................81
Piles: 2x LR6 / Mignon / AA 3. Verwijdering..................................................................81
Durée de vie des piles: env. 3 ans 4. Batterijen plaatsen / vervangen....................................82
Écran: écran à cristaux liquides 5. Datum en tijd instellen..................................................83
Dimension du boîtier: 58 x 71,5 x 90 mm (l x h x p) 6. Montage aan de radiator..............................................84
Raccord: M30 x 1,5 7. Aanpassingstermijn......................................................91
Température ambiante: 0 à 55 °C 8. Weekprogramma instellen............................................91
Max. Température 9. Gebruiksmodi...............................................................96
de surface: +90°C (sur le radiateur) 10. Configuratiemenu.......................................................96
Course linéaire: 4,3 mm 11. Displayinhoud bij normaal gebruik..............................97
12. Boost-functie..............................................................97
Sous réserve de modifications techniques destinées 13. Vakantiefunctie instellen.............................................98
à améliorer le produit. 14. Comfort- en verlagende temperatuur.........................98
15. Kinderbeveiliging / bedieningsblokkering...................99
16. Verwarmingspauze activeren (batterijbesparing).......99
17. Vriesbeveiliging instellen..........................................100
18. Raam-open-functie...................................................100
19. Offset-temperatuur instellen.....................................101
20. Fabrieksinstellingen terugzetten...............................101
21. Correct gebruik.........................................................102
22. Probleemoplossing en onderhoud............................102
23. Omvang van de levering..........................................103
24. Technische gegevens...............................................103
Lees deze handleiding zorgvuldig door, vóór u het apparaat in ge-
bruikneemt. Bewaar de handleiding, om ze ook later nog te kun-
nen raadplegen.
84 85
6.1. Adapter voor Danfoss De adapters RA en RAV zijn gemaakt voor een betere
Voor de montage op ventielen van Danfoss is een van de pasvorm met voorspanning. Bij de montage gebruikt u
meegeleverde adapters nodig. Het vaststellen van de pas- eventueel een schroevendraaier en buigt u deze licht in
sende adapterring voor het desbetreffende ventiel kunt u het gebied van de schroef. Na het vergrendelen van de
in de afbeeldingen zien. ventielknop bevestigt u de adapter met de meegeleverde
schroef en moer.
Let er bij de montage op dat uw vingers niet klem ko-
men te zitten tussen de adapterhelften!
E
De ventielbehuizingen van Danfoss hebben langwerpige
groeven (E) die ook een betere pasvorm van de adapter
na het monteren garanderen.
D
Let er bij de montage op dat de pinnen in de adapter
(D) een overeenkomende positie met de groeven (E)
aan het ventiel hebben.
Zet de volledig passende adapter op het ventiel.
86 87
Op ventielen van het type RAV is voor de montage een De adapter RAVL moet niet worden verschroefd.
stootverlenging (F) op de ventielpin te zetten.
E E
D D
Let er bij de montage op dat de pinnen in de adapter
(D) een overeenkomende positie met de groeven (E)
Let er bij de montage op dat de pinnen in de adapter aan het ventiel hebben.
(D) een overeenkomende positie met de groeven (E) Zet de volledig passende adapter op het ventiel.
aan het ventiel hebben.
Zet de volledig passende adapter op het ventiel.
88 89
Steunring 7. Aanpassingstermijn
De ventielen van verschillende producenten kunnen tole- Na het inleggen van de batterijen gaat de motor terug ter-
rantieafwijkingen vertonen die kunnen leiden tot een los- wijl het activiteitensymbool ‚INS‘ wordt ( ) weergegeven.
se pasvorm van de programmeerbare radiatorregelaar op Zodra ‚INS‘ zonder activiteitensymbool ( ) in het display
het ventiel. Door het gebruik van de meegeleverde steun- staat, kan de programmeerbare radiatorregelaar gemon-
ring kunnen de stabiliteit en de pasvorm op het ventiel teerd worden. Daarna wordt voor het aanpassen aan het
worden verbeterd ventiel een aanpassingstermijn (‚AdA‘) uitgevoerd.
Leg de steunring (G) in de flens of op de ventielaanslui-
ting van de radiatorbehuizing en schroef het thermostaat- • Zet de programmeerbare radiatorregelaar op het ventiel.
ventiel aan. • Trek de wartelmoer vast.
Als de steunring niet kan worden bevestigd dan is de stabi- • Druk op de Boost-toets als er ‚INS‘ op het display staat.
liteit goed genoeg en is deze niet nodig voor de montage.
De aandrijving voert een aanpassingstermijn uit. Daarbij
worden ‚AdA‘ en het activiteitensymbool ( ) op het dis-
play weergegeven, wanneer geen bediening mogelijk is.
8. Weekprogramma instellen
In het weekprogramma zijn voor elke werkdag apart tot 3
verwarmingsfases (7 schakeltijdstippen) in te stellen. De
programmering gebeurt voor de uitgekozen dagen waarbij
voor een tijdruimte van 00:00 tot 23:59 temperaturen moe-
ten worden ingevoerd.
94 95
9. Gebruiksmodi
AER: raam-open-temperatuur en -tijd voor de au-
Door kort op de Mode-knop 7 te drukken kan tussen de vol- tomatische temperatuurverlaging kan bij het
gende 3 bedrijfsmodi worden gewisseld (de bedrijfsmodi luchten ingesteld worden
kunnen pas na de montage worden gekozen):
• ( ) Vakantiefunctie: het instellen van een temperatuur TOF: offset-temperatuur instellen
die tot een bepaald tijdpunt kan worden aangehouden. RES: herstellen van de fabrieksinstellingen
• Manu: handmatig gebruik - de temperatuur wordt hand-
matig via het verstelwiel ingesteld.
• Auto: weekprogramma - automatische temperatuurre- 11. Displayinhoud bij normaal gebruik
geling op basis van de opgeslagen weekprogramma‘s.
Bij normaal gebruik worden de schakeltijdruimte, werkmo-
dus, gewenste temperatuur en
10. Configuratiemenu weekdag weergegeven. De
balken voor schakeltijdruimte
In het configuratiemenu zijn de instellingen te veranderen. van het weekprogramma wor-
Het menu is met een lange druk (langer dan 3 seconden) den voor elke tweede tijdinter-
op de menu-toets naar voren te halen. Menudelen worden val weergegeven (voorbeeld
met het verstelwiel uitgekozen en met OK 5 bevestigd. Een bij ‚weekprogramma: voorbeelden‘).
nieuwe druk op de menu-toets leidt terug naar een vorige
menu. Indien meer dan 65 seconden geen gebruik van het 12. Boost-functie
menu wordt gemaakt dan sluit het menu automatisch. U kunt
de volgende instellingen gebruiken: De Boost-functie is voor het menselijke warmtegevoel. Bij
activatie wordt het verwarmingsventiel direct 5 minuten op
PRO: instelling van het weekprogramma (zie para- 80% geopend (fabrieksinstelling). De verwarming van een
graaf ‚Weekprogramma instellen‘) ruimte duurt langer dan 5 minuten, maar de aangegeven
warmte van de radiator kan direct worden waargenomen.
DAT: veranderen van tijd en datum Komt u eerder naar huis en wilt u het snel warm hebben
of heeft u ‚s morgens in de badkamer extra warmte nodig
POS: aanvragen van de huidige positie van de aan-
drijving dan helpt de Boost-functie u.
DST: De automatische omschakeling tussen zo- • Druk op de Boost-toets voor het activeren van de Boost-
mer- en wintertijd kan worden gedeactiveerd. functie.
• De resterende tijd van de functie telt terug per seconde
(‚B299‘ tot B000‘).
96 97
• Na verloop van deze 5 minuten wisselt de aandrijving tuur). Ze kunnen als volgt worden aangepast:
terug naar de vorige actieve modus (Autom/Manu) met
de vorige ingestelde temperatuur. • Houd de comfort-/verlagende temperatuurtoets ( )
• De functie is altijd voortijdig door een druk op de knop lang ingedrukt.
of het door gebruiken van het verstelwiel te deactiveren • In het display verschijnt het zonnesymbool ( ) en de
huidige opgeslagen comforttemperatuur.
De Boost-toets heeft geen direct effect als de radiator • Verander de temperatuur met het verstelwiel en beves-
wordt bedekt (door bijvoorbeeld een bank). De raam- tig met de OK-toets.
openherkenning is tijdens de Boost-functie gedeac- • In het display verschijnt het maansymbool ( ) en de ver-
tiveerd. lagende temperatuur.
• Verander de temperatuur met het verstelwiel en beves-
13. Vakantiefunctie instellen tig met de OK-toets.
Indien tijdens een vakantie of een feest voor een bepaalde
tijd een vaste temperatuur moet worden aangehouden dan Ook in de automatische modus kan de temperatuur te al-
kan de vakantiefunctie worden gebruikt. len tijde ook via de toets worden veranderd. Deze blijft dan
aanhouden tot het volgende schakeltijdstip.
• Druk zo vaak kort op de menu-toets totdat het koffersym-
bool ( ) verschijnt.
• Stel via het verstelwiel de tijd in tot wanneer de temperatuur 15. Kinderbeveiliging / bedieningsblokkering
moet worden aangehouden en bevestig met de OK-toets. De bediening aan het apparaat kan worden
• Stel daarna de datum in met het verstelwiel en bevestig geblokkeerd:
met de OK-toets.
• Stel de temperatuur met het verstelwiel in en bevestig met • Voor het activeren/deactiveren van de bedieningsblokke-
OK. De weergave knippert voor de bevestiging. ring drukt u de knoppen menu en kort gelijktijdig in.
Na succesvolle activatie verschijnt ‚LOC‘ in het display.
De ingestelde temperatuur blijft bestaan tot het aangege- • Voor het deactiveren van de bedieningsblokkering drukt
ven tijdstip. Daarna gaat de aandrijving in de auto-modus. u opnieuw op beide knoppen.
18. Raam-open-functie
De aandrijving herkent bij een sterk lager wordende tem- 20. Fabrieksinstellingen terugzetten
peratuur automatisch dat een raam geopend is. Om ver- De fabrieksinstellingen van de programmeerbare radi-
warmingskosten te besparen wordt de temperatuur dan atorregelaar kunnen handmatig door een reset worden
voor een bepaalde tijd naar beneden gezet (standaard 15 hersteld. Daarbij gaan alle handmatig opgeslagen instel-
minuten). Dan wordt er in het display het raam-open-sym- lingen verloren.
bool ( ) weergegeven. Ga als volgt te werk:
Voor het activeren gaat u als volgt te werk: • Houd de menu-toets langer dan 3 seconden ingedrukt.
• Druk langer dan 3 seconden op de menu-toets. • Kies met het verstelwiel het menugedeelte ‚RES‘ en be-
• Kies met het verstelwiel het menugedeelte ‚AER‘ en be- vestig met de OK-toets.
vestig met de OK-toets. • Vervolgens verschijnt ‚CFM‘ in het display.
• Bevestig met de OK-toets.
100 101
21. Correct gebruik 23. Omvang van de levering
De programmeerbare radiatorregelaar is bedoeld voor het
reguleren van een gebruikelijk radiatorventiel. Gebruik het Programmeerbare radiatorregelaar
apparaat alleen in binnenruimtes en vermijd het contact
met vocht, stof en zonne- of warmtebestraling. Elk ander Adapter Danfoss RA
gebruik dan in deze gebruiksaanwijzing beschreven is niet Adapter Danfoss RAV
correct en zorgt voor het vervallen van de garantie en aan- Stootverlenging Danfoss RAV
sprakelijkheid. Dit geldt ook voor wijzigingen en veranderin- Adapter Danfoss RAVL
gen. Dit product is uitsluitend bestemd voor privégebruik. Cylinderschroef M4 x 12, Moer M4
Steunring
22. Probleemoplossing en onderhoud
Foutcode in 24. Technische gegevens
Probleem Oplossing
het display
Batterijsymbool Batterijniveau Voedingsspanning: 3V
Batterij vervangen Max. stroomopname: 100 mA
( ) te laag
Batterijen: 2x LR6 / Mignon / AA
Installatie controle-
Ventielaandrij- Batterijlevensduur: ca. 3 jaar
F1 ren, verwarmings-
ving stug Display: LC-Display
ventiel controleren
Bevestiging van de Behuizingsafmetingen: 58 x 71,5 x 90 mm (B x H x T)
Instelbereik te Aansluiting: M30 x 1,5
F2 radiatorregelaar con-
groot Omgevingstemperatuur: 0 bis 55 °C
troleren
Instelbereik te Radiatorventiel con- Max.
F3 Oppervlaktetemperatuur: +90°C (aan de radiator)
klein troleren
Lineaire slag: 4,3 mm
Voor de bescherming voor ventielverkalking voert de
programmeerbare radiatorregelaar eenmaal per week Technische veranderingen die voor de verbeterin-
op zaterdag om 12:00 h een ontkalkingsprocedure uit. gen dienen, zijn voorbehouden.
Daarbij verschijnt ‚CAL‘ in het display.
102 103
Bevollmächtigter des Herstellers:
Manufacturer’s authorised representative:
eQ-3 AG
Maiburger Straße 29
26789 Leer / GERMANY
www.eQ-3.de