Beruflich Dokumente
Kultur Dokumente
Installationsanleitung
OPT/i WF Gasdüsen- DE
Positionssuchen Systemerweiterung
Installations instructions
OPT/i WF gas nozzle touch sensing
EN
System extension
Instructions d'installation
Fonction de recherche de position
FR
42,0410,1943 004-13122016
2
Inhaltsverzeichnis
DE
Allgemeines ............................................................................................................................................... 5
Lieferumfang ......................................................................................................................................... 5
Einbaulage ............................................................................................................................................ 5
Benötigtes Werkzeug............................................................................................................................ 6
OPT/i WF Gasdüsen-Positionssuchen in WF 15i/25i/30i R / SB 500i R einbauen .................................... 7
Sicherheit .............................................................................................................................................. 7
Vorbereitung ......................................................................................................................................... 8
OPT/i WF Gasdüsen-Positionssuchen einbauen.................................................................................. 8
Abschließende Tätigkeiten.................................................................................................................... 11
OPT/i WF Gasdüsen-Positionssuchen in SB 60i R einbauen.................................................................... 12
Sicherheit .............................................................................................................................................. 12
Vorbereitung ......................................................................................................................................... 12
OPT/i WF Gasdüsen-Positionssuchen einbauen.................................................................................. 13
Abschließende Tätigkeiten.................................................................................................................... 14
3
4
Allgemeines
DE
Lieferumfang
(1) Sensor
(2) 2 Schrauben TX 20
4 x 10 mm
(3) 2 Schrauben TX 20
(1) 5 x 25 mm
Ohne Abbildung:
diese Installationsanleitung
(2)
(3)
Einbaulage
OPT/i WF Gasdüsen-Positionssuchen kann bei folgenden Geräten eingebaut werden
- alle Varianten der Geräte WF 15i/25i/30i R und R PAP
- alle Varianten der Geräte SB 500i R und R PAP
- alle Varianten der Geräte SB 60i R
Ist OPT/i WF Ausblasen 7 bar bereits im Gerät eingebaut, muss OPT/i WF Gasdüsen-
Positionssuchen auf der gegenüberliegen Seite von OPT/i WF Ausblasen 7 bar im Gerät
eingebaut werden. Unabhängig von der Montageseite im Gerät ist der Einbau wie be-
schrieben durchzuführen.
(1) (1)
Ansicht der Geräte-Rückseite mit demontierter Ge- Ansicht der Geräte-Rückseite mit demontierter Ge-
häuseabdeckung häuseabdeckung
5
Benötigtes Werk- - Torx-Schraubendreher TX 20
zeug
6
OPT/i WF Gasdüsen-Positionssuchen in WF 15i/25i/
30i R / SB 500i R einbauen
DE
Sicherheit
WARNUNG! Fehlbedienung und fehlerhaft durchgeführte Arbeiten können
schwerwiegende Personen- und Sachschäden verursachen.
Alle in diesem Dokument beschriebenen Arbeiten und Funktionen dürfen nur von
geschultem Fachpersonal ausgeführt werden, wenn folgende Dokumente voll-
ständig gelesen und verstanden wurden:
- dieses Dokument
- sämtliche Bedienungsanleitungen der Systemkomponenten, insbesondere
Sicherheitsvorschriften
WARNUNG! Ein elektrischer Schlag kann tödlich sein. Vor Beginn der Arbeiten:
- Netzschalter der Stromquelle in Stellung - O - schalten
- Stromquelle vom Netz trennen
- sicherstellen, dass die Stromquelle bis zum Abschluss aller Arbeiten vom
Netz getrennt bleibt
Nach dem Öffnen des Gerätes mit Hilfe eines geeigneten Messgerätes sicher-
stellen, dass elektrisch geladene Bauteile (z.B. Kondensatoren) entladen sind.
7
Vorbereitung
1 Sämtliche Verbindungen des Gerätes von allen anderen Systemkomponenten tren-
nen
2 Gerät auf einer geeigneten Unterlage ablegen
3 4 Schrauben TX 20 (1) lösen
4 Abdeckung (2) öffnen
5 Gehäuseabdeckung (3) wie abgebildet vom Gerät abziehen
(1) (1)
(2)
(3)
(1) (1)
OPT/i WF Gasdü-
1 Sensor (1) wie abgebildet in das Gerät einsetzen und mittels Schraube TX 20 (2) an
sen-Positionssu-
der Position (3) festschrauben
chen einbauen
(3)
(2)
(1)
8
2 Sensor (1) mittels Schraube TX 20 (4) an der Position (5) festschrauben
DE
(1)
(4)
(5)
9
5 Vorkonfektioniertes Kabel (10) vom
(10) (8) Sensor (1) wie abgebildet in Anschluss
6 des Steckers (8) einstecken
5 6 7 8
10
Abschließende
DE
HINWEIS! Beim Montieren der Gehäuseabdeckung sicherstellen, dass Kabel
Tätigkeiten
und Schläuche nicht geknickt, eingeklemmt, abgescheuert oder auf andere
Weise beschädigt werden.
1 Gehäuseabdeckung (3) wie abgebildet bis auf Anschlag auf das Gerät aufschieben
2 4 Schrauben TX 20 (1) festschrauben
3 Abdeckung (2) schließen
4 Gerät in seine Ausgangsposition bringen
5 Verbindungen mit anderen Systemkomponenten herstellen
(1) (1)
(2)
(3)
(1) (1)
11
OPT/i WF Gasdüsen-Positionssuchen in SB 60i R
einbauen
Sicherheit
WARNUNG! Fehlbedienung und fehlerhaft durchgeführte Arbeiten können
schwerwiegende Personen- und Sachschäden verursachen.
Alle in diesem Dokument beschriebenen Arbeiten und Funktionen dürfen nur von
geschultem Fachpersonal ausgeführt werden, wenn folgende Dokumente voll-
ständig gelesen und verstanden wurden:
- dieses Dokument
- sämtliche Bedienungsanleitungen der Systemkomponenten, insbesondere
Sicherheitsvorschriften
WARNUNG! Ein elektrischer Schlag kann tödlich sein. Vor Beginn der Arbeiten:
- Netzschalter der Stromquelle in Stellung - O - schalten
- Stromquelle vom Netz trennen
- sicherstellen, dass die Stromquelle bis zum Abschluss aller Arbeiten vom
Netz getrennt bleibt
Nach dem Öffnen des Gerätes mit Hilfe eines geeigneten Messgerätes sicher-
stellen, dass elektrisch geladene Bauteile (z.B. Kondensatoren) entladen sind.
Vorbereitung Der Einbau wird anhand einer rechten SB 60i R Geräteausführung beschrieben. Der Ein-
bau in eine linke SB 60i R Geräteausführung erfolgt analog dazu.
12
4 6 Schrauben TX25 (1) lösen
(1) 5 Abdeckung (2) abnehmen
DE
(1)
(1)
(1)
(2)
(1)
5 6 7 8
(3)
(4)
(6)
(8)
13
Abschließende Gasschlauch wieder am Magnetventil
1
Tätigkeiten anschließen
(1)
2 Abdeckung (2) einsetzen
3 Abdeckung mit 6 Schrauben TX25 (1)
(1) fixieren
Anzugsmoment = 3 Nm
(1)
(1)
(2)
(1)
14
Contents
General ...................................................................................................................................................... 17
Scope of supply .................................................................................................................................... 17
Installation position ............................................................................................................................... 17
Tools required ....................................................................................................................................... 18
EN
Installing the OPT/i WF gas nozzle touch sensing in the WF 15i/25i/30i R / SB 500i R ............................ 19
Safety.................................................................................................................................................... 19
Preparations.......................................................................................................................................... 20
Installing the OPT/i WF gas nozzle touch sensing................................................................................ 20
And finally... .......................................................................................................................................... 23
Installing the OPT/i WF gas nozzle touch sensing in the SB 500i R.......................................................... 24
Safety.................................................................................................................................................... 24
Preparatory work................................................................................................................................... 24
Installing the OPT/i WF gas nozzle touch sensing................................................................................ 25
And finally... .......................................................................................................................................... 26
15
16
General
Scope of supply
(1) Sensor
EN
(2) 2 x TX20 screws
4 x 10 mm
Not shown:
these Installation Instructions
(2)
(3)
Installation posi-
OPT/i WF gas nozzle touch sensing can be installed on the following devices
tion
- all variants of the WF 15i/25i/30i R and R PAP
- all variants of the SB 500i R and R PAP
- all variants of the SB 60i R
If OPT/i WF 7 bar gas purging is already installed in the device, OPT/i WF gas nozzle
touch sensing must be installed on the opposite side from the OPT/i WF 7 bar gas purging
option. The installation must be carried out as described, irrespective of the installation
side.
(1) (1)
View of the rear of the device with housing cover re- View of the rear of the device with housing cover re-
moved moved
17
Tools required - TX20 Torx screwdriver
18
Installing the OPT/i WF gas nozzle touch sensing in
the WF 15i/25i/30i R / SB 500i R
Safety
EN
WARNING! Incorrect operation or shoddy workmanship can cause serious injury
or damage.
All functions described in this document may only be carried out by trained and
qualified personnel after they have fully read and understood the following docu-
ments:
- this document
- all the operating instructions for the system components, especially the safe-
ty rules
After opening the device, use a suitable measuring instrument to check that elec-
trically charged components (e.g. capacitors) have been discharged.
CAUTION! Risk of injury from wire electrode emerging at speed. If the welding
system contains an unreeling wirefeeder, also carry out the following actions be-
fore starting work:
- turn the mains switch of the unreeling wirefeeder to the "O" position
- disconnect the unreeling wirefeeder from the mains
- ensure that the unreeling wirefeeder remains disconnected from the mains
until all work has been completed
CAUTION! Risk of scalding from hot system components. Before starting work,
allow all hot system components to cool down to room temperature (+25°C,
+77°F). For example:
- coolant
- water-cooled system components
- wirefeeder drive motor
19
Preparations
1 Disconnect all connections on the device from all other system components
2 Place the device on a suitable base
3 Undo four TX 20 screws (1)
4 Open cover (2)
5 Pull the housing cover (3) off the device as shown
(1) (1)
(2)
(3)
(1) (1)
Installing the
1 Insert the sensor (1) into the device as shown and secure in position (3) using a TX
OPT/i WF gas
20 screw (2)
nozzle touch
sensing
(3)
(2)
(1)
20
2 Screw the sensor (1) to position (5) using a TX 20 screw (4)
EN
(1)
(4)
(5)
21
5 Insert the pre-assembled cable (10)
(10) (8) from the sensor (1) into connection 6 of
the plug (8) as shown
5 6 7 8
22
And finally...
NOTE! When fitting the housing cover, ensure that the cables and hoses are not
kinked, trapped, sheared or damaged in any way.
1 Push housing cover (3) as far as it will go onto the device as shown
EN
2 Tighten the four TX 20 screws (1)
3 Close the cover (2)
4 Return the device to its original position
5 Establish connections to other system components
(1) (1)
(2)
(3)
(1) (1)
23
Installing the OPT/i WF gas nozzle touch sensing in
the SB 500i R
Safety
WARNING! Incorrect operation or shoddy workmanship can cause serious injury
or damage.
All functions described in this document may only be carried out by trained and
qualified personnel after they have fully read and understood the following docu-
ments:
- this document
- all the operating instructions for the system components, especially the safe-
ty rules
After opening the device, use a suitable measuring instrument to check that elec-
trically charged components (e.g. capacitors) have been discharged.
CAUTION! Risk of injury from wire electrode emerging at speed. If the welding
system contains an unreeling wirefeeder, also carry out the following actions be-
fore starting work:
- turn the mains switch of the unreeling wirefeeder to the "O" position
- disconnect the unreeling wirefeeder from the mains
- ensure that the unreeling wirefeeder remains disconnected from the mains
until all work has been completed
CAUTION! Risk of scalding from hot system components. Before starting work,
allow all hot system components to cool down to room temperature (+25°C,
+77°F). For example:
- coolant
- water-cooled system components
- wirefeeder drive motor
Preparatory work Installation is described based on the right-hand version of the SB 60i R. Installation of the
left-hand version of the SB 60i R is carried out in the same way.
1 Disconnect all connections on the device from all other system components
2 Detach the device from the robot (4 x Allen screws M6 x 60 mm)
3 Place the device on a suitable base with the transparent cover facing down
24
4 Undo the six TX25 screws (1)
(1) 5 Remove cover (2)
(1)
EN
(1)
(1)
(2)
(1)
5 6 7 8
(3)
(4)
(6)
(8)
25
And finally... Reconnect the gas hose to the sole-
1
(1) noid valve
2 Fit the cover (2)
3 Secure the cover with six TX25 screws
(1) (1)
Tightening torque = 3 Nm
(1)
(1)
(2)
(1)
26
Sommaire
Généralités................................................................................................................................................. 29
Contenu de la livraison ......................................................................................................................... 29
Emplacement de montage .................................................................................................................... 29
Outillage nécessaire ............................................................................................................................. 30
Installer l'option de recherche de position buses de gaz OPT/i WF en WF 15i/25i/30i R / SB 500i R....... 31
Sécurité................................................................................................................................................. 31
Préparation ........................................................................................................................................... 32
Installer l'option de recherche de position buses de gaz OPT/i WF...................................................... 32
Opérations finales ................................................................................................................................. 35
FR
Installer l'option de recherche de position buses de gaz OPT/i WF en SB 500i R .................................... 36
Sécurité................................................................................................................................................. 36
Préparation ........................................................................................................................................... 36
Installer l'option de recherche de position buses de gaz OPT/i WF...................................................... 37
Étapes finales ....................................................................................................................................... 38
27
28
Généralités
Contenu de la li-
vraison (1) Capteur
(2) 2 vis TX 20
4 x 10 mm
(3) 2 vis TX 20
(1) 5 x 25 mm
FR
Sans illustration :
les présentes Instructions d'installation
(2)
(3)
Emplacement de
L'option de recherche de position des buses de gaz OPT/i WF peut être installée sur les
montage
appareils suivants
- toutes les variantes des appareils WF 15i/25i/30i R et R PAP
- toutes les variantes des appareils SB 500i R et R PAP
- toutes les variantes des appareils SB 60i R
Si le soufflage OPT/i WF 7 bar est déjà monté dans l'appareil, l'option de recherche des
buses de gaz OPT/i WF doit être montée sur le côté opposé dans l'appareil. Indépendam-
ment du côté de montage dans l'appareil, l'installation doit être effectuée comme décrit
ci-après.
(1) (1)
Vue de la face arrière de l'appareil avec capot du Vue de la face arrière de l'appareil avec capot du
boîtier démonté boîtier démonté
(1) Dévidoir/SplitBox
(2) Soufflage OPT/i WF 7 bar
(3) Option de recherche de position buses de gaz OPT/i WF
29
Outillage néces- - tournevis Torx TX 20
saire
30
Installer l'option de recherche de position buses de
gaz OPT/i WF en WF 15i/25i/30i R / SB 500i R
Sécurité
AVERTISSEMENT ! Les erreurs de commande et les erreurs en cours d'opéra-
tion peuvent entraîner des dommages corporels et matériels graves.
L'ensemble des opérations et travaux décrits dans le présent document ne
doivent être effectués que par du personnel qualifié ayant lu et compris l'intégra-
lité des documents suivants :
FR
- le présent document
- toutes les Instructions de service des composants périphériques, en particu-
lier les consignes de sécurité
31
Préparation
1 Débrancher toutes les connexions de l'appareil avec les autres composants périphé-
riques
2 Placer l'appareil sur un support adapté
3 Desserrer les 4 vis TX 20 (1)
4 Ouvrir le capot (2)
5 Retirer le capot du boîtier (3) comme illustré
(1) (1)
(2)
(3)
(1) (1)
Installer l'option
1 Placer le capteur (1) dans l'appareil comme indiqué sur l'illustration et le visser en
de recherche de
position (3) à l'aide d'une vis TX 20 (2)
position buses de
gaz OPT/i WF
(3)
(2)
(1)
32
2 Visser le capteur (1) en position (5) à l'aide d'une vis TX 20 (4)
(1)
(4)
(5)
FR
3 Raccorder le connecteur plat du câble
(7) (6) (6) du capteur (1) au connecteur (7) de
l'appareil comme indiqué sur l'illustrati-
on
33
5 Raccorder le câble préconfectionné
(10) (8) (10) du capteur (1) au raccord 6 du
connecteur (8) comme indiqué sur l'il-
lustration
5 6 7 8
34
Opérations fi-
REMARQUE! Lors du montage du capot du boîtier, veiller à ce que le câble et
nales
le tuyau ne soient pas coincés, coudés, usés ou endommagés de toute autre
manière.
1 Pousser le capot du boîtier (3) sur l'appareil comme indiqué sur l'illustration jusqu'à
la butée
2 Visser les 4 vis TX 20 (1)
3 Fermer le capot (2)
FR
4 Replacer l'appareil dans sa position initiale
5 Rétablir la connexion avec les autres composants périphériques
(1) (1)
(2)
(3)
(1) (1)
35
Installer l'option de recherche de position buses de
gaz OPT/i WF en SB 500i R
Sécurité
AVERTISSEMENT ! Les erreurs de commande et les erreurs en cours d'opéra-
tion peuvent entraîner des dommages corporels et matériels graves.
L'ensemble des opérations et travaux décrits dans le présent document ne
doivent être effectués que par du personnel qualifié ayant lu et compris l'intégra-
lité des documents suivants :
- le présent document
- toutes les Instructions de service des composants périphériques, en particu-
lier les consignes de sécurité
Préparation L'installation est décrite selon le modèle d'appareil SB 60i R droit. L'installation dans un
modèle d'appareil SB 60i R gauche s'effectue de façon similaire.
1 Débrancher toutes les connexions de l'appareil avec tous les autres composants pé-
riphériques
2 Démonter l'appareil du robot (4 x vis à tête à six pans creux M6 x 60 mm)
3 Poser l'appareil sur un support adapté avec le cache transparent vers le bas
36
4 Desserrer les 6 vis TX25 (1)
(1) 5 Retirer le cache (2)
(1)
(1)
(1)
(2)
FR
(1)
5 6 7 8
(3)
(4)
(6)
(8)
37
Étapes finales Raccorder à nouveau le tuyau de gaz
1
(1) à l'électrovanne
2 Remettre le cache (2) en place
3 Fixer le cache avec 6 vis TX25 (1)
(1) Couple de serrage = 3 Nm
(1)
(1)
(2)
(1)
4 Monter l'appareil sur le robot (4 x vis à tête à six pans creux M6 x 60 mm)
5 Rétablir la connexion avec les autres composants périphériques
38
FR
39
FRONIUS INTERNATIONAL GMBH
Froniusplatz 1, A-4600 Wels, Austria
Tel: +43 (0)7242 241-0, Fax: +43 (0)7242 241-3940
E-Mail: sales@fronius.com
www.fronius.com
www.fronius.com/addresses
Under http://www.fronius.com/addresses you will find all addresses
of our Sales & service partners and Locations